LOWER EXHAUST NO DRILLING REQUIRED...YEARS:2017-CURRENT KIA MODEL: SPORTAGE SUV 3,500 350 TRAILER...
5
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT. WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS. WARNING: ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY ** WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY *** FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM & FOR HELPFUL TOWING TIPS LOG ONTO WWW.HITCHINFO.COM HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634 HITCH WEIGHT: LBS. INSTALL TIME PROFESSIONAL: MINUTES NOVICE (DIY): MINUTES INSTALL NOTES: INSTALLATION STEPS PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND. CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684. 3,500 350 33 20 KIA SPORTAGE 8/13/2020 12158 40 Scan for more information Parts List DESCRIPTION PART NUMBER QTY ITEM HHCS,M10x1.25,30,CL10.9,YZ 10-10271 8 1 WASHER, S-CON,7/16,YZ 30-00163 8 2 1 2 PASSENGER SIDE FRAME RAIL DRIVER SIDE FRAME RAIL EXISTING WELDNUTS (BOTH SIDES) TOOLS REQUIRED RATCHET 17mm SOCKET TORQUE WRENCH 6 in. SOCKET EXTENSION FLATHEAD SCREWDRIVER SAFETY GLASSES -NO DRILLING REQUIRED -LOWER EXHAUST -TEMPORARILY REMOVE UNDERBODY PANELS 1. Remove (3) plastic clips attaching the panel cover on the driver and passenger side of vehicle. Pull panel covers downward to remove from vehicle. Retain hardware and panels for reinstallation. Note: The white fasteners that attach the panel covers to studs on the vehicle may pull off the covers during cover removal. Unthread the fasteners from the studs and reinsert the fasteners into position on the panel covers. 2. Lower exhaust by detaching (2) exhaust isolators. 3. Raise hitch into position and secure to vehicle using M10 hardware and 7/16" conical toothed washers, as shown. 4. Torque M10 hardware to 48 lb-ft. 5. Raise exhaust back into position and reattach exhaust isolators removed in Step 2. 6. Reinstall underbody panels removed in Step 1. DESIGNED FOR USE WITH BALL MOUNT # 45521 EURO MOUNT OPTION AVAILABLE #45571 (1 7/8" BALL) #45572 (2" BALL)
Transcript of LOWER EXHAUST NO DRILLING REQUIRED...YEARS:2017-CURRENT KIA MODEL: SPORTAGE SUV 3,500 350 TRAILER...
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
WARNING: ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY **
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM & FOR HELPFUL TOWING TIPS LOG ONTO WWW.HITCHINFO.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERSARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
3,500 350
33
20
KIA SPORTAGE8/13/202012158
40
Scanfor moreinformation
Parts ListDESCRIPTIONPART NUMBERQTYITEM
HHCS,M10x1.25,30,CL10.9,YZ10-1027181
WASHER, S-CON,7/16,YZ30-0016382
1
2
PASSENGER SIDEFRAME RAIL
DRIVER SIDEFRAME RAIL
EXISTING WELDNUTS(BOTH SIDES)
TOOLS REQUIREDRATCHET
17mm SOCKETTORQUE WRENCH
6 in. SOCKET EXTENSIONFLATHEAD SCREWDRIVER
SAFETY GLASSES
-NO DRILLING REQUIRED-LOWER EXHAUST-TEMPORARILY REMOVE UNDERBODY PANELS
1. Remove (3) plastic clips attaching the panel cover on the driver and passenger side of vehicle. Pull panel covers downward to remove from vehicle. Retain hardware and panels for reinstallation. Note: The white fasteners that attach the panel covers to studs on the vehicle may pull off the covers during cover removal. Unthread the fasteners from the studs and reinsert the fasteners into position on the panel covers. 2. Lower exhaust by detaching (2) exhaust isolators. 3. Raise hitch into position and secure to vehicle using M10 hardware and 7/16" conical toothed washers, as shown. 4. Torque M10 hardware to 48 lb-ft. 5. Raise exhaust back into position and reattach exhaust isolators removed in Step 2. 6. Reinstall underbody panels removed in Step 1.
DESIGNED FOR USE WITH BALL MOUNT # 45521
EURO MOUNT OPTION AVAILABLE#45571 (1 7/8" BALL)
#45572 (2" BALL)
MAKE: STYLE:
MIN.20
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITYFor more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY: EASY
EASY MODERATE CHALLENGING
Safety glasses should be worn at all times whileinstalling this product.
YEARS: 2017-CURRENT KIA MODEL: SPORTAGE SUV
3,500350
TRAILER WEIGHT:TONGUE WEIGHT:
12158 INSTALLATION INSTRUCTIONS
LBS.LBS.
WARNING: WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER (WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT WWW.CURTMFG.COM FOR FURTHER INFORMATION.
MIN.MIN.40
IF YOU ARE HESITANT TO UNDERTAKETHIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
NOVICE INSTALL TIME: PRO INSTALL TIME:
SCAN FORMORE INFO
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this productvoids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.comThis product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684. 8/13/2020
1. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY. 2. TO EASE INSTALLATION, 2 PEOPLE MAY BE REQUIRED. 3. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED. 4. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 877.287.8634
RATCHET SOCKET
17mm TORQUE
WRENCH
SOCKETEXTENSION
6"SCREWDRIVER
SAFETYGLASSES
PART REMOVAL
NO DRILLING REQUIRED
LOWER EXHAUST
TEMPORARILY REMOVEUNDERBODY PANELS
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HHCS,M10x1.25,30,CL10.9,YZ10-1027181
WASHER, S-CON,7/16,YZ30-0016382
1
2
DRIVER SIDE FRAME RAIL
PASSENGER SIDE FRAME RAIL
EXISTING WELDNUTS(BOTH SIDES)
1. Remove (3) plastic clips attaching the panel cover on the driver and passenger side of vehicle. Pull panel covers downward to remove from vehicle. Retain hardware and panels for reinstallation. Note: The white fasteners that attach the panel covers to studs on the vehicle may pull off the covers during cover removal. Unthread the fasteners from the studs and reinsert the fasteners into position on the panel covers.
2. Lower exhaust by detaching (2) exhaust isolators.
EURO MOUNT OPTION AVAILABLE#45571 (1 7/8" BALL)
#45572 (2" BALL)
DESIGNED FOR USE WITH BALL MOUNT # 45521
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
3. Raise hitch into position and secure to vehicle using M10 hardware and 7/16" conical toothed washers, as shown.
4. Torque M10 hardware to 48 lb-ft.
5. Raise exhaust back into position and reattach exhaust isolators removed in Step 2.
6. Reinstall underbody panels removed in Step 1
