Lok-BoL t AS 1 Material Specifications 2 - Powers · General Information..... 1 Material...
5
www.powers.com 1 TECH MANUAL – MECHANICAL ANCHORS ©2016 POWERS – REV. D GENERAL INFORMATION SECTION CONTENTS MECHANICAL ANCHORS General Information...................... 1 Material Specifications ................. 2 Installation Specifications ............ 2 Installation Instructions ................ 3 Performance Data .......................... 4 Ordering Information .................... 5 HEX HEAD HEAD STYLES • Hex Head • Acorn Nut • Round Head • Combo Flat Head • Threshold Flat Head • Rod Hanger • Tie-Wire ANCHOR MATERIALS • Zinc Plated Carbon Steel • Type 304 Stainless Steel ANCHOR SIZE RANGE (TYP.) • 1/4" diameter through 3/4" diameter SUITABLE BASE MATERIALS • Normal-Weight Concrete • Grouted Concrete Masonry (CMU) • Hollow Concrete Masonry (CMU) • Brick Masonry GENERAL INFORMATION LOK-BOLT AS ® Sleeve Anchor PRODUCT DESCRIPTION The Lok-Bolt AS is an all-steel pre-assembled single unit sleeve anchor which is designed for use in concrete or masonry base materials. The anchors are available in multiple head styles for multiple applications and a finished appearance. Anchor extender sleeves can be added to create longer lengths. GENERAL APPLICATIONS AND USES • Door and window frame installations • Masonry applications • Electrical / Mechanical applications • Mounting fixtures on walls • General purpose anchoring FEATURES AND BENEFITS + Variety of head styles, lengths and sizes + All steel component design + Preassembled anchor for immediate installation + Sleeve design keeps anchor centered in hole + Sleeve has 360° contact area for even stress distribution + Versatile – can be used for solid and hollow concrete or masonry applications + Designed to allow fixture to draw snug against the base material during tightening GUIDE SPECIFICATIONS CSI Divisions: 03 16 00 - Concrete Anchors and 05 05 19 - Post-Installed Concrete Anchors Expansion anchors shall be Lok-Bolt AS as supplied by Powers Fasteners, Inc., Brewster, NY. Anchors shall be installed in accordance with published instructions and the Authority Having Jurisdiction.
Transcript of Lok-BoL t AS 1 Material Specifications 2 - Powers · General Information..... 1 Material...
www.powers.com 1
TECH MAN
UAL – MECHAN
iCAL ANCHo
rs ©2016 Po
WErs – rEv. d
General InformatIon
Section contentS
Mech
an
ica
l a
nch
or
s
General Information ......................1Material Specifications .................2Installation Specifications ............2Installation Instructions ................3Performance Data ..........................4Ordering Information ....................5
Hex Head
Head StyleS• HexHead• AcornNut• RoundHead• ComboFlatHead• ThresholdFlatHead• RodHanger• Tie-Wire
ancHor MaterialS• ZincPlatedCarbonSteel• Type304StainlessSteel
ancHor Size range (tyP.)• 1/4"diameterthrough3/4"
diameter
Suitable baSe MaterialS• Normal-WeightConcrete• GroutedConcreteMasonry(CMU)• HollowConcreteMasonry(CMU)• BrickMasonry
general inforMation
Lok-BoLt AS®
Sleeve Anchor
Product deScriPtion
The Lok-Bolt As is an all-steel pre-assembled single unit sleeve anchor which is designed for use in concrete or masonry base materials. The anchors are available in multiple head styles for multiple applications and a finished appearance. Anchor extender sleeves can be added to create longer lengths.
GenerAL APPLicAtionS And uSeS
•Doorandwindowframeinstallations
•Masonryapplications
•Electrical/Mechanicalapplications
•Mountingfixturesonwalls
•Generalpurposeanchoring
FeAtureS And BeneFitS
+ Varietyofheadstyles,lengthsandsizes
+ Allsteelcomponentdesign
+ Preassembledanchorforimmediateinstallation
+ Sleevedesignkeepsanchorcenteredinhole
+ Sleevehas360°contactareaforevenstressdistribution
+ Versatile–canbeusedforsolidandhollowconcreteormasonryapplications
+ Designedtoallowfixturetodrawsnugagainstthebasematerialduringtightening
Guide SPeciFicAtionS
Csi divisions: 03 16 00 - Concrete Anchors and 05 05 19 - Post-installed Concrete Anchors Expansion anchors shall be Lok-Bolt As as supplied by Powers Fasteners, inc., Brewster, NY. Anchors shall be installed in accordance with published instructions and the Authority Having Jurisdiction.
www.powers.com 2
materIal SpecIfIcatIonS
TECH
MAN
UAL
– M
ECHA
NiC
AL A
NCH
ors
©20
16 P
oW
Ers
– r
Ev. d
Mech
an
ica
l a
nch
or
sMaterial SPecificationSAnchor Component Carbon Steel Version Stainless Steel Version
Plow-Bolt Aisi 1010/1018 Type 304 stainless steel
Expansion sleeve Aisi 1010 Type 304 stainless steel
Extender Aisi 1010 N/A
Zinc Plating AsTM B 633, sCi, Type iii (Fe/Zn5) N/A
inStallation SPecificationS
Acorn Nut and Hex Head Lok-Bolt AS
DimensionNominal Anchor Diameter, d
1/4" 5/16" 3/8" 1/2" 5/8" 3/4"
ANsi drill Bit size, dbit (in.) 1/4 5/16 3/8 1/2 5/8 3/4
Fixture Clearance Hole, dh (in.) 5/16 3/8 7/16 9/16 11/16 15/16
Plow Bolt size (UNC) 10-24 1/4-20 5/16-18 3/8-16 1/2-13 5/8-11
Nut Height (in.) 3/16 7/32 17/64 21/64 7/16 35/64
Washer o.d., dw (in.) 1/2 5/8 13/16 1 1-3/8 1-3/4
Wrench size (in.) 3/8 7/16 1/2 9/16 3/4 15/16
Round Head Lok-Bolt AS
DimensionNominal Anchor Diameter, d
1/4" 5/16" 3/8"
ANsi drill Bit size, dbit (in.) 1/4 5/16 3/8
Fixture Clearance Hole, dh (in.) 5/16 3/8 7/16
Plow Bolt size (UNC) 10-24 1/4-20 5/16-18
Head Height (in.) 11/64 13/64 15/64
Head Width, dhd (in.) 29/64 9/16 43/64
Combo Flat Head Lok-Bolt AS
DimensionNominal Anchor Diameter, d
1/4" 5/16" 3/8"
ANsi drill Bit size, dbit (in.) 1/4 5/16 3/8
Fixture Clearance Hole, dh (in.) 5/16 3/8 7/16
Plow Bolt size (UNC) 10-24 1/4-20 5/16-18
Head Height (in.) 5/32 3/16 15/64
Head Width, dhd (in.) 1/2 5/8 3/4
Rod Hanger Lok-Bolt AS
DimensionNominal Anchor Diameter, d
1/4" 5/16" 3/8"
ANsi drill Bit size, dbit (in.) 5/16 3/8 1/2
Plow Bolt size (UNC) 1/4-20 5/16-18 3/8-16
Coupling Height (in.) 7/8 1 1-1/4
Washer o.d., dw (in.) 5/8 13/16 1
Coupling Wrench size (in.) 3/8 1/2 11/16
Threshold Lok-Bolt AS
DimensionAnchor Size, d
1/4"
ANsi drill Bit size, dbit (in.) 1/4
Fixture Clearance Hole, dh (in.) 5/16
Plow Bolt size (UNC) 10-24
Head Height (in.) 5/64
Head Width, dhd (in.) 23/64
Tie-Wire Lok-Bolt AS
DimensionAnchor Size, d
5/16"
ANsi drill Bit size, dbit (in.) 5/16
Fixture Clearance Hole, dh (in.) 3/8
Plow Bolt size (UNC) 1/4-20
Head Height (in.) 1-9/16
Head Width, dhd (in.) 31/64
www.powers.com 3
TECH MAN
UAL – MECHAN
iCAL ANCHo
rs ©2016 Po
WErs – rEv. d
InStallatIon InStructIonS
Mech
an
ica
l a
nch
or
s
inStallation inStructionS
Hex/Acorn/Flat Head Round Versions
Rod Hanger Version Tie-Wire Version
Using the proper diameter bit, drill a hole into the base material to a depth of at least 1/2" or one anchor diameter deeper than the embedment required.
The tolerances of the drill bit used must meet the requirements of ANsi standard B212.15
Using the proper diameter bit, drill a hole into the base material to a depth of at least 1/2" or one anchor diameter deeper than the embedment required.
The tolerances of the drill bit used must meet the requirements of ANsi standard B212.15
Using the proper diameter bit, drill a hole into the base material to a depth of at least 1/2" or one anchor diameter deeper than the embedment required.
The tolerances of the drill bit used must meet the requirements of ANsi standard B212.15
Blow the hole clean of dust and other material. do not expand the anchor prior to installation.
Blow the hole clean of dust and other material. do not expand the anchor prior to installation.
Blow the hole clean of dust and other material. do not expand the anchor prior to installation.
Hex Head/Acorn Nut Position the washer on the anchor and thread on the nut.
drive the anchor through the fixture into the anchor hole until the nut and washer are firmly seated against the fixture. Be sure the anchor is driven to the required embedment depth.
drive the anchor into the hole until the anchor is at the required embedment depth.
drive the anchor into the hole until the head is firmly seated against the base material. Be sure the anchor is driven to the required embedment depth.
Flat Head/round Headdrive the anchor through the fixture until the anchor is firmly seated. Be sure the anchor is driven to the required embedment depth.
Tighten the coupler nut and washer up to the concrete surface and tighten the anchor by turning the nut 3 to 5 turns past finger tight or by applying the guide installation torque from the finger tight position.
Tighten the tie wire nut by turning the head 3 to 5 turns past finger tight or by applying the guide installation torque from the finger tight position.
Hex Head/Acorn NutTighten the anchor by turning the nut or head 3 to 5 turns past finger tight or by applying the guide installation torque from the finger tight position.
Flat Head/round HeadTighten the anchor by turning the head 3 to 5 turns past finger tight.
www.powers.com 4
performance Data
TECH
MAN
UAL
– M
ECHA
NiC
AL A
NCH
ors
©20
16 P
oW
Ers
– r
Ev. d
Mech
an
ica
l a
nch
or
sPerforMance data
Ultimate and Allowable Load Capacities for Carbon and Stainless Steel Lok-Bolt AS Anchors in Normal Weight Concrete1,2,3
NominalAnchor
Diameterdin.
Min. Embed. Depth
hv in.
Guide Installation Torqueft.-lbs.
Minimum Concrete Compressive Strength, f’c
3,000 psi 3,500 psi 4,000 psi
Carbon StainlessUltimate Allowable Ultimate Allowable Ultimate Allowable
Tensionlbs.
Shearlbs.
Tensionlbs.
Shearlbs.
Tensionlbs.
Shearlbs.
Tensionlbs.
Shearlbs.
Tensionlbs.
Shearlbs.
Tensionlbs.
Shearlbs.
1/4 1/2 2 - 225 1,000 55 250 240 1,000 60 250 260 1,000 65 250
1 6 4 910 1,120 230 280 980 1,120 245 280 1,050 1,120 265 280
5/16 1 12 - 1,205 2,360 300 590 1,300 2,360 325 590 1,390 2,360 350 590
3/8 1-1/4 18 18 1,875 4,110 470 1,030 2,040 4,110 510 1,030 2,165 4,110 540 1,030
1/2 1-1/2 26 26 2,235 4,860 560 1,215 2,420 4,860 605 1,215 2,580 4,860 645 1,215
5/8 2 50 40 4,870 4,860 1,220 1,215 5,260 4,860 1,315 1,215 5,625 4,860 1,405 1,215
3/4 2-1/4 90 60 5,045 11,040 1,260 2,760 5,450 11,040 1,365 2,760 5,825 11,040 1,455 2,760
1. Theultimateloadvalueslistedabovemustbereducedbyaminimumsafetyfactorof4.0orgreatertodeterminetheallowableworkingload.Considerationofsafetyfactorsof10orhighermaybenecessarydependingontheapplication,suchaslifesafetyoroverhead.
2. Allowableloadcapacitieslistedarecalculatedusinganappliedsafetyfactorof4.0.Considerationofsafetyfactorsof10orhighermaybenecessarydependingontheapplication,suchaslifesafetyoroverhead.
3. Tabulatedloadvaluesareforanchorsinstalledataminimumspacingdistancebetweenanchorsandanedgedistanceof12timestheanchordiameters.
Ultimate and Allowable Load Capacities for Carbon and Stainless Steel Lok-Bolt AS Anchors in Hollow or Solid Concrete Masonry1,2,3,4
NominalAnchor
Diameterdin.
Minimum Embed.Depth
hv
in.
Guide Installation
Torqueft.-lbs.
Minimum Edge Dist.
in.
Minimum End Dist.
in.
Ultimate Loads Allowable Loads
Tensionlbs.
Shearlbs.
Tensionlbs.
Shearlbs.
1/4 1 4
3-3/4 4
800 1,140 160 225
5/16 1 8 905 1,570 180 310
3/8 1-1/4 15 1,100 1,570 220 310
1/2 1-1/2 18 1,525 1,570 305 310
5/8 1-1/2 30 2,250 1,770 450 355
1.Tabulatedloadvaluesareforanchorsinstalledinminimum6inchwide,GradeN,TypeII,normal-weightconcretemasonryunitsconformingtoASTMC90.MortarmustbeminimumTypeN,S,orM.Masonryprismcompressivestrengthmustbe1,500psiminimumattimeofinstallation.
2.Allowableloadcapacitieslistedarecalculatedusinganappliedsafetyfactorof5.0.Considerationofsafetyfactorsof10orhighermaybenecessarydependingontheapplication,suchaslifesafetyoroverhead.
3.Asuitableanchorlengthmustbeselectedwhichincludesconsiderationofafixturetoengagethebasematerialattheminimumembedmentdepthwhenanchoringintohollowconcretemasonry.(e.g.attachmentthickness+faceshellthicknessembedment+onehalfinch=suitableanchorlength)
4.Theconsistenceofhollowconcreteblockmasonrybasematerialcanvarygreatly.Considerationofjobsitetestingshouldbegiventoverifyconformanceofbasematerialsandanchorperformanceinactualconditions.
Ultimate and Allowable Load Capacties for Carbon or Stainless Steel Lok-Bolt AS Anchors in Solid Clay Brick Masonry1,2
NominalAnchor
Diameterdin.
Minimum Embed.Depth
hv
in.
Guide Installation
Torqueft.-lbs.
Minimum Edge Dist.in.
Minimum End Dist.
in.
f’m ≥ 1,500 psi (10.4 MPa)
Ultimate Allowable
Tensionlbs.
Shearlbs.
Tensionlbs.
Shearlbs.
1/4 1 4 4 1-1/2 800 950 160 190
3/8 1-1/4 15 8 8 1,100 3,000 220 600
1/2 1-1/2 26 8 8 1,560 3,150 310 630
5/8 2 40 8 8 2,470 5,250 495 1,050
1.TabulatedloadvaluesareforanchorsinstalledinGradeSW,multiplewythesolidclaybrickmasonryconformingtoASTMC62.2.Allowableloadcapacitieslistedarecalculatedusingasafetyfactorof5.0orgreater.Considerationofsafetyfactorsof10orhighermaybenecessarydependingontheapplication,
suchaslifesafety.
www.powers.com 5
TECH MAN
UAL – MECHAN
iCAL ANCHo
rs ©2016 Po
WErs – rEv. d
orDerInG InformatIon
Mech
an
ica
l a
nch
or
s
ordering inforMation
Hex Nut Lok-Bolt ASCatalog Number
Size Drill Dia.
Std. Box
Std. Ctn.Carbon
SteelStainless
Steel
5005s - 5/16" x 1-1/2" 5/16" 100 1000
5010s - 5/16" x 2-3/8" 5/16" 100 500
5015s 6152s 3/8" x 1-7/8" 3/8" 50 500
5020s 6153s 3/8" x 3" 3/8" 50 500
5022s - 3/8" x 4" 3/8" 50 250
5025s 6156s 1/2" x 2-1/2" 1/2" 25 250
5030s 6157s 1/2" x 3" 1/2" 25 250
5034s 6160s 1/2" x 3-3/4" 1/2" 25 125
5033s - 1/2" x 5-1/4" 1/2" 25 125
5032s - 1/2" x 6" 1/2" 10 100
5035s - 5/8" x 2-1/2" 5/8" 25 125
5038s - 5/8" x 3" 5/8" 25 125
5040s 6164s 5/8" x 4-1/4" 5/8" 10 100
5045s - 5/8" x 5-3/4" 5/8" 10 100
5050s - 3/4" x 2-3/4" 3/4" 10 100
5055s - 3/4" x 4-1/4" 3/4" 10 40
5060s - 3/4" x 6-1/4" 3/4" 10 30
5065s - 3/4" x 8-1/4" 3/4" 10 30
Acorn Nut Lok-Bolt ASCatalog Number
Size Drill Dia.
Std. Box
Std. Ctn.Carbon
SteelStainless
Steel
5125s - 1/4" x 5/8" 1/4" 100 1000
5150s 6150s 1/4" x 1-3/8" 1/4" 100 1000
5175s - 1/4" x 2-1/4" 1/4" 100 1000
Round Head Lok-Bolt AS, SlottedCatalog Number
Size Drill Dia.
Std. Box
Std. Ctn.Carbon
SteelStainless
Steel
5205s - 1/4" x 1-3/8" 1/4" 100 1000
5210s 6180s 1/4" x 2-1/4" 1/4" 100 1000
5215s - 1/4" x 3" 1/4" 100 1000
5220s - 1/4" x 3-3/4" 1/4" 100 1000
5225s - 5/16" x 2-3/8" 5/16" 100 1000
5230s - 5/16" x 3-3/8" 5/16" 100 500
5235s - 3/8" x 2-3/4" 3/8" 50 500
5240s - 3/8" x 3-3/4" 3/8" 50 250
Combo Flat Head Lok-Bolt ASCatalog Number
Size Drill Dia.
Std. Box
Std. Ctn.Carbon
SteelStainless
Steel
5305s - 1/4" x 1-1/2" 1/4" 100 1000
5310s 6170s 1/4" x 2-1/4" 1/4" 100 1000
5315s 6172s 1/4" x 3" 1/4" 100 1000
5320s - 1/4" x 4" 1/4" 100 500
5325s - 1/4" x 5-1/4" 1/4" 100 500
5330s - 5/16" x 2-1/2" 5/16" 100 1000
5340s - 3/8" x 2-3/4" 3/8" 50 500
5345s 6174s 3/8" x 4" 3/8" 50 250
5350s 6175s 3/8" x 5" 3/8" 50 250
5360s 6176s 3/8" x 6" 3/8" 50 250
Threshold Flat Head Lok-Bolt AS
Cat # Size Drill Dia.
Std. Box
Std. Ctn.
5500s 1/4" x 2" 1/4" 100 1000
Rod Hanger Lok-Bolt AS
Cat # Size Drill Dia.
Std. Box
Std. Ctn.
5810s 1/4" x 1-1/2" 5/16" 50 250
5815s 3/8" x 1-7/8" 3/8" 50 250
5825s 1/2" x 2-1/4" 1/2" 25 125
Tie-Wire Lok-Bolt AS
Cat # Size Drill Dia.
Std. Box
Std. Ctn.
5700s 5/16" x 2-3/8" 5/16" 100 1000
Lok-Bolt AS Extenders
Cat # Size Drill Dia.
Std. Box
Std. Ctn.
5684s 3/8" x 1-1/4" 3/8" 50 500
