LNL Hardware Demo Guide

PERPETUA

Lenel Access Hardware Demo System User Guide

L INNOVATION

Lenel OnGuard® 2012 Lenel Access Hardware Demo System User Guide, product version 6.5. This guide is item number DOC-971, revision 2.002, November 2011

Copyright © 2008-2012 Lenel Systems International, Inc. Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Lenel Systems International, Inc.

Non-English versions of Lenel documents are offered as a service to our global audiences. We have attempted to provide an accurate translation of the text, but the official text is the English text, and any differences in the translation are not binding and have no legal effect.

The software described in this document is furnished under a license agreement and may only be used in accordance with the terms of that agreement. Lenel and OnGuard are registered trademarks of Lenel Systems International, Inc.

Microsoft, Windows, Windows Server, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Integral and FlashPoint are trademarks of Integral Technologies, Inc. Crystal Reports for Windows is a trademark of Crystal Computer Services, Inc. Oracle is a registered trademark of Oracle Corporation. Other product names mentioned in this User Guide may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.

Portions of this product were created using LEADTOOLS © 1991-2012 LEAD Technologies, Inc. ALL RIGHTS RESERVED.

OnGuard includes ImageStream® Graphic Filters. Copyright © 1991-2012 Inso Corporation. All rights reserved. ImageStream Graphic Filters and ImageStream are registered trademarks of Inso Corporation.

Table of Contents

CHAPTER 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

CHAPTER 2 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Intelligent System Controller (ISC) LNL-2220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Single Reader Interface Module LNL-1300 Series 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

XCeedID (LNL-XF-1050-B) OpenProx Multiclass Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

HID (800-8045-3020) MIFARE Sector Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

HID (RWKL550) OSDP LCD iCLASS Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

CHAPTER 3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

LNL-2220 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11LAN Connection (Default Connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

LNL-1300 Single Reader Interface Configuration (Port 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13LNL-1300 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

LNL-2220 IDRC Onboard Reader 1 Configuration (Port 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

LNL-2220 IDRC Onboard Reader 2 Configuration (Port 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

LNL-2220 IDRC Reader Interface Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

LNL-2220 IDRC Reader Interface Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Local I/O Setup for Auxiliary Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Card Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Enabling User Commands/Extended Hold Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Lenel Access Hardware Demo System User Guide 3

Table of Contents

Command Keypad Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Command Programming Assignment (HID OSDP Reader) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

APPENDIX A Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

ISC Communication Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

ISC Setup Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Single Reader Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34AUX Output 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Dual Reader Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Reader 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36AUX Input 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37AUX Output 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37AUX Input 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Reader 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38AUX Input 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39AUX Output 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39AUX Input 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

APPENDIX B Demonstration Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Valid User Presents Card to Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

User Presents Invalid Badge to Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Valid User Arms the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

APPENDIX C Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

4 Lenel Access Hardware Demo System User Guide

CHAPTER 1 Introduction

The Lenel Access Hardware Demo System (refered to throughout this guide as “Demo Case”) includes the following hardware:

• ISC LNL-2220

• SRI LNL-1300

• XCeedID (LNL-XF-1050-B) OpenProx Multiclass Reader

• HID (800-8045-3020) Mifare Sector Reader

• HID (RWKL550) OSDP LCD iClass Reader

• Three inputs

• Three outputs

• Output reset button

• Amber LED power indicator

• Three door contacts with tipped LED

• RS-485 asset reader connection

• 6-foot retractable CAT 5e crossover cable


Introduction

6

• LenelProx w/Magstripe Sample Card

• HID 2k/2 application area iClass sample card

• Mifare Sample Card

• 12 VDC universal power supply

• Soft-sided carrying case

In addition, a laptop PC is required to run OnGuard software that was installed with the Demo Case database.

• For a description of the hardware installed in the Demo Case, refer to Chapter 2: Hardware on page 7.

• For a description of the Lenel hardware and OnGuard database configuration for the Demo Case, refer to Chapter 3: Configuration on page 11.

• For a reference table overview of the OnGuard Demo Case database configuration, refer to Appendix A: Configuration Overview on page 33.

• For a description of scenarios you can use to demonstrate the Lenel access hardware and OnGuard software, refer to Appendix B: Demonstration Scenarios on page 41.

• For a Demo Case wiring interconnect diagram, refer to Appendix C: Wiring Diagram on page 43.


CHAPTER 2 Hardware

This chapter describes the hardware included in the Lenel Access Hardware Demo System. For wiring interconnections, refer to Wiring Diagram on page 43.

Intelligent System Controller (ISC) LNL-2220

The LNL-2220 Intelligent System Controller (IDRC) by Lenel provides a single board solution for interfacing one or two doors to an OnGuard system. In addition, other I/O and reader interface modules can be added on the LNL-2220's downstream port to expand its capabilities. The LNL-2220 revolutionizes access control system architecture by allowing Ethernet connection directly from an entry location to the OnGuard server, while still providing the security, functionality, and modularity of Lenel's proven access series hardware platform. The LNL-2220 is scalable for any access control application, from the most basic to the most sophisticated. In the event of communication loss, the LNL-2220 allows nearly all local functionality to continue unimpaired until the server connection is restored.

Utilizing its native Ethernet communications and an advanced 32-bit processor, the LNL-2220 can communicate upstream to the host computer through its Ethernet port (with a throughput up to eight times greater than the fastest serial connections) or at up to 115.2Kbps using RS-232 communication directly or through an external dial-up modem. The LNL-2220 can store up to 250,000 cardholders in non-volatile flash memory, and supports selective download for larger cardholder databases. The downstream RS-485 two-wire port can be used to connect up to 32 devices (maximum 64 doors).

Two on-board reader ports support Data1/Data0, Clock/Data, Bioscrypt RS-485 readers and the bidirectional RS-485 Open Supervised Device Protocol (OSDP) communications. Each LNL-2220 supports up to eight different card formats. The LNL-2220 includes eight inputs that support normally open, normally closed, supervised and unsupervised circuits. In addition, four output relays support fail-safe or fail-secure operation.


Hardware

8

Single Reader Interface Module LNL-1300 Series 2

Lenel Systems International offers a Single Reader Interface (SRI) module for access control solutions. Access control card readers, keypads, or readers with keypads that use standard Wiegand Data1/Data0 or Clock/Data communication are supported, as are those that support the new bidirectional RS-485 Lenel OnGuard Supervised Device Protocol (OSDP). Lock, unlock, and facility code offline access modes are supported on all readers connected to the SRI. Each DRI supports up to eight different card formats as well as issue codes for both magnetic and Wiegand card formats.

The SRI provides a vital link between the Intelligent System Controller (ISC) and the card reader attached to the interface. As many as 32 SRI modules can be multi-dropped using RS-485 2-wire communication up to 4,000 feet per port away from the ISC. Each SRI module is individually addressed for increased reporting capabilities with OnGuard access control software applications. The SRI includes two inputs that support normally open, normally closed, supervised, and non-supervised circuits. Two output relays support fail-safe or fail-secure operation.

XCeedID (LNL-XF-1050-B) OpenProx Multiclass Reader

The Lenel OpenProx Reader supports all major 125 kHz card standards. The Lenel OpenProx Reader provides compatibility with HID® proximity, GE/CASI ProxLite®, XceedID® proximity, AWID®, and LenelProx card formats. Lenel provides a single compact reader that can integrate diverse proximity card populations, or allow seamless transition from one 125 kHz technology to another.

The mullion reader is perfect for narrow-rail mullion installations. It can be used as a sleek and unobtrusive unit, as well as in standard wall-mounted reader applications.

HID (800-8045-3020) MIFARE Sector Reader

The HID MIFARE Sector Reader is a flexible, highly secure and stylish contactless smart card reader ideal for customers that require a customizable reader for new or existing installations. The reader is designed for a wide variety of applications from entry-level access control to secure ID management.

The reader’s keypad adds an extra layer of protection for higher security installations.

HID (RWKL550) OSDP LCD iCLASS Reader

Using 13.56 MHz contactless smart card technology, the HID OSDP LCD iCLASS Reader provides users with new options for supporting multi-factor identity authentication. Combine a contactless card presentation with a personal identification number (PIN) to securely control access to high security areas. Turn the reader into a remotely controlled device, enabling a host to read and write data on an iCLASS card in addition to controlling the LCD to display time, badgeholder information, and so on.

Versatile communication interfaces allow any host to connect to and communicate with the reader. Local operation mode (access control) allows the reader to interface with the highly secure iCLASS access control application, sending card data one-way to a host over a Wiegand, RS232 or RS485 (point-to-point) physical link while displaying canned messages to the user (multi-language support configurable). Use remote operation mode (pass-through) to open up two-way communications over


HID (RWKL550) OSDP LCD iCLASS Reader

RS232, RS485 (point-to-point) or USB interfaces. Read and write unique application data on iCLASS cards while controlling the LCD, beeper and LEDs.


Hardware

10

CHAPTER 3 Configuration

This chapter describes the hardware and software configuration of the Lenel Access Hardware Demo System.

LNL-2220 Configuration

LAN Connection (Default Connection)

The Lenel Access Demo System has a network cable cutout on the top of the unit where the cable will connect directly into the LNL-2220. By default, all dipswitches are set to OFF and the factory default IP address is set to 192.168.0.251, Address 0. To assign a different parameters to the ISC, refer to the OnGuard Hardware Installation documentation.

LNL-2220 Settings

Parameter Setting

Address 0

Baud rate 38.4 kbps

RAM 16 MB

PIN 1 to 4 digits


Configuration

12

LNL-2220 Tab

System Administration > Access Control > Access Panels

Connection Tab

Options Tab


LNL-1300 Single Reader Interface Configuration (Port 2)


System Administration > Access Control > Readers and Doors

LNL-1300 Settings

General Tab

Parameter Setting

Address 31

Baud rate 38.4 kbps

Input power 12 Vdc unregulated

Communication interface RS-485 2-wire

Parameter Setting

Name 1-HID OSDP Reader

Port 2

Address 31

Reader number 0


Configuration

14

Settings Tab

Controls Tab



LNL-1300 Outputs

Aux Outputs Tab.

SRI Output Address Setting

RLY 1 Door Strike HID OSDP Reader

RLY 2 Armed

Parameter Setting

Output 1 Name Armed

Output 1 Pulse Time (sec) 5


Configuration

16

LNL-2220 IDRC Onboard Reader 1 Configuration (Port 3)


General Tab

Settings Tab

Parameter Setting

Name 3-MIFARE Reader w/PINPad

Address 0

Reader number 0



Controls Tab


Configuration

18



General Tab

Settings Tab

Parameter Setting

Name 2-Lenel OpenProx

Address 0

Reader number 1



Controls Tab


Configuration

20

LNL-2220 IDRC Reader Interface Inputs


Aux Inputs Tab for MIFARE Reader w/PinPad (IN 3 and IN 4)

Aux Inputs Tab for Lenel OpenProx (IN 6 and IN 7)

IDRC Input Address Description

IN 1 Non-supervised - Door 1 Contact MIFARE Reader w/PINPad

IN 2 Non-supervised - Door 1 REX MIFARE Reader w/PINPad

IN 3 Non-supervised - Door 1 Aux 1 - Door

IN 4 Non-supervised - Door 1 Aux 2 - Window

IN 5 Non-supervised - Door 2 Contact - Lenel OpenProx

IN 6 Non-supervised - Door 2 REX - Lenel OpenProx

IN 7 Non-supervised - Door 2 Aux 1 - Motion

IN 8 Non-supervised - Door 2 Aux 2 - Reset


LNL-2220 IDRC Reader Interface Outputs

LNL-2220 IDRC Reader Interface Outputs


Aux Outputs Tab for MIFARE Reader w/PinPad (OUT 2)

Aux Outputs Tab for Lenel OpenProx (OUT 4)

DRI Output Address Description

OUT 1 Non-supervised - Door 1 Contact MIFARE Reader w/PINPad

OUT 2 Non-supervised - Door 1 REX MIFARE Reader w/PINPad

OUT 3 Non-supervised - Door 2 Contact - Lenel OpenProx

OUT 4 Non-supervised - Door 2 REX - Lenel OpenProx


Configuration

22

Local I/O Setup for Auxiliary Inputs and Outputs

System Administration > Access Control > Local I/O

Local I/O Function List Tab

Device > Function Links Tab


Card Formats

Card Formats

System Administration > Administration > Card Formats

Card Format Tab for OpenProx Format (36-Bit), All Readers

Card Format Tab for FASC-N (200-Bit) HID OSDP and MIFARE Reader with PINPad


Configuration

24

Card Format Tab for FASC-N (75-Bit) HID OSDP Reader and MIFARE Reader with PINPad

Card Format Tab for Lenel OpenCard Format (36-Bit), All Readers


Card Formats

Card Format Tab for Magnetic Format, Not Assigned

Card Format Tab for SEWIG (Access Control), Not Assigned


Configuration

26

Custom Encoding Tab for SEWIG (Access Control), Not Assigned

Card Format Tab for SEWIG GSC (Encoding), Not Assigned


Card Formats

Custom Encoding Tab for SEWIG GSC (Encoding), Not Assigned

Card Format Tab for OSDP Format (26-Bit), All Readers


Configuration

28

Groups

System Administration > Access Control > Groups

Mask Groups Tab


Enabling User Commands/Extended Hold Options

Enabling User Commands/Extended Hold Options

System Administration > Administration > System Options

User Commands Tab

Command Keypad Templates

System Administration > Access Control > Command Keypad Templates

Macro Assignments Tab


Configuration

30

User Feedback Tab

Default Mask Group Intusion Commands Tab


Command Keypad Templates

Any Mask Group Intrusion Commands Tab


Configuration

32

Command Programming Assignment (HID OSDP Reader)


Command Programming Tab


APPENDIX A Configuration Overview

This appendix provides the Lenel Access Hardware Demo Case configuration parameter settings.


Configuration Overview

34

ISC Communication Parameters

ISC Setup Parameters

Single Reader Interface

Parameter Setting

Workstation <your workstation name>

IP address 192.168.0.251

Baud rate 38400

Memory 16 MB

Connection type LAN

Panel Address 0

Online YES

Parameter Setting

Number of cardholders 500

Options None

Store activate date YES

Store deactivate date YES

PIN Type 1-4 digit PIN

Store anti-passback location

NO

Parameter Setting

Reader name HID OSDP Reader

Type Single interface (OSDP Protocol)

Port 2

Address 31

Reader number 0

Online mode Pin or card

Offline mode Pin or card

Allow user commands YES


Single Reader Interface

Allow intrusion commands

YES

Held open time (sec) 20

Extended open (sec) 75

Strike time (sec) 10

Extended strike (sec) 25

Elevator reader NO

Card formats AWID Format, FASC-N 200 Bit, FASC-N 75 Bit, Lenel Corporate Format, Wiegand Format (26-Bit)

Pin format Eight bit output keypads

Parameter Setting



36

AUX Output 1

Dual Reader Interface

Reader 1

Parameter Setting

Name Armed

Pulse time 5 seconds

Activate during time zone

None

Parameter Setting

Reader name MIFARE Reader w/PINPad

Type IDRC Onboard Reader 1 (Mag w/ Wiegand Output)

Port

Address 0

Reader number 0

Online mode Pin or card

Offline mode Pin or card

Allow user commands YES


YES





Elevator reader NO

Card formats AWID Format, FASC-N 200 Bit, FASC-N 75 Bit, Lenel Corporate Format, Wiegand Format (26-Bit)

Pin format Eight bit output keypads



AUX Input 1

AUX Output 1

AUX Input 2

Parameter Setting

Name MIFARE Reader w/ PINPad

Input 1 Door

Input ID 1

Contact normally open YES

Online YES

Always mask NO

Mask during time zone None

Entry delay 10

Exit delay 10

Non-latch entry NO

NOT SUPERVISED

Parameter Setting

Name Door



None

Parameter Setting

Name MIFARE Reader w/ PINPad

Input 2 Window

Input ID 2


Online YES

Always mask NO


Entry delay 0

Exit delay 0



38

Reader 2

Non-latch entry NO

NOT SUPERVISED

Parameter Setting

Reader name Lenel OpenProx

Type IDRC Onboard Reader 2 (Wiegand/Prox)

Port

Address 0

Reader number 1

Online mode Card only

Offline mode Card only

Allow user commands NO


NO





Elevator reader NO

Card formats AWID Format, Lenel Corporate Format, Wiegand Format (26-Bit)

Pin format No keypad

Parameter Setting



AUX Input 1

AUX Output 1

AUX Input 2

Parameter Setting

Name Lenel OpenProx

Input 3 Motion

Input ID 3


Online YES

Always mask NO


Entry delay 0

Exit delay 0

Non-latch entry NO

NOT SUPERVISED

Parameter Setting

Name Alarm



None

Parameter Setting

Name Lenel OpenProx

Input 4 Reset

Input ID 4


Online YES

Always mask NO


Entry delay 0

Exit delay 0



40

Non-latch entry NO

NOT SUPERVISED

Parameter Setting


APPENDIX B Demonstration Scenarios

Valid User Presents Card to Reader

Switch tip will light up green depicting a door strike. User toggles the corresponding door switch to trigger a simulated contact break in a typical door open/close scenario.

User Presents Invalid Badge to Reader

Door LED tipped toggle switch will not light up. When presented to the HID OSDP reader, user will see "Access Denied" on the LCD screen.

Valid User Arms the System

• Armed LED will illuminate. At this point, a motion, window or door switch under the left wing will illuminate an Alarm LED.

Note: IN1 (Door) has an entry and exit delay of 10 sec.

• Any user can use the F3 key on the HID OSDP reader to view faulted zones.

• Any user with valid access can use the F4 key on the HID OSDP reader to enable extended hold on Door1.

• When the system is armed and an output(s) is activated, the Reset button (IN4) will deactivate all of the outputs except the Armed output.

• By default, upon power up, the system is in an Armed state.


Demonstration Scenarios

42

APPENDIX C Wiring Diagram

Refer to the Figure 1 on page 44 if you need to remove and replace the Demo Case modules.


Wiring Diagram

44

FIGURE 1. Demo Case Wiring Diagram


Lenel Systems International, Inc.1212 Pittsford-Victor RoadPittsford, New York 14534 USATel 585.248.9720 Fax [email protected]

LNL Hardware Demo Guide

Documents

Transcript of LNL Hardware Demo Guide