L2 V4 04 Basic Modules Configuration E 01

8/20/2019 L2 V4 04 Basic Modules Configuration E 01

1/17

Basic Modules

Configuration

PCLPCLPCLPCL

PACiSPACiSPACiSPACiS TechnicalTechnicalTechnicalTechnical TrainingTrainingTrainingTraining LevelLevelLevelLevel 2 22 2

CS&PCS&PCS&PCS&P – –– – Support Team Support Team Support Team Support Team


2/17

Schneider Electric 2- CS&P – Basic Modules Configuration – E01

• Content

Circuit Breaker

Disconnector Switch

Transformer

Generic Module


3/17


• Content

Circuit Breaker

Disconnector Switch

Transformer

Generic Module


4/17


• Add / Configure a CB1) Circuit Breaker can be added at Bay level in Electric hierarchy.

CB 3 phases (1 DPS for global position) / CB 1 phase (single phase acq.)

Short Name :SCE Key + appears in viewers + printers

CB Type :3-ph, 1-ph, other

2) CB attributes

Nodes definition :AVR


5/17


• CB-1ph Configuration (1)1) CB 1 phase basic configuration

1.1) Type 1

Typed Switch Ctrl DPC :DPC Open/Close

Typed CB Computed Position DPS :- Global CB Position, computed by C264

- is feedback of DPC command - is animated on PACiS OI / C264 LCD

Typed Switchgear ph A,B,C DPS :

CB single phase position, acquired by C264(DI/CCU or IED)

1.2) Type 2

Position can be computed by :

- typed Switch ph A DPS- typed Phases Not Together SPS

Note : Positions can be SPS


6/17


• CB-1ph Configuration (2)2) CB enhanced configuration => possible sons

Typed Lock Control SPC :Operator lock

Typed Selection SPC :when SBO, activated at selection

Typed Sync CB Close :Synchrocheck

Typed Lock SPS :Lock status

Typed Phase Not Together SPS :- Indicates if all phases are in same position

- holds a timer for CB trip

Typed withdrawn SPS :brushable devices


7/17


• CB-3ph Configuration1) CB 3 phases basic configuration

1.1) Type 1


Typed CB Computed Position DPS :- Global CB Position, computed by C264 - is feedback of DPC command

- is animated on PACiS OI / C264 LCD

Typed Switchgear position DPS :CB Position, acquired by C264 (DI/CCU or IED)

1.2) Type 2

Typed Switch Ctrl DPC can be replaced by :

- typed Switch Ctrl SPC for CLOSE- typed Switch ph A SPC for OPEN

Note : Positions can be SPS


8/17


• Content

Circuit Breaker

Disconnector Switch

Transformer

Generic Module


9/17


• Add / Configure a Disconnector Switch1) Disconnector switch is a Switchgear , it can be added at Bay level in

Electric hierarchy.


2) DS attributes



10/17


• Switchgear Configuration (1)1) Switchgear basic configuration


Typed Switchgear position DPS :Switchgear Position, acquired by C264 (DI/CCUor IED)

Note : Position can be SPS


11/17


• Switchgear Configuration (2)2) Switchgear enhanced configuration => possible sons

Typed Lock Control SPC :Operator lock

Typed Selection SPC :when SBO, activated at selection

Typed Lock SPS :Lock status

Typed withdrawn SPS :brushable devices


12/17


• Content

Circuit Breaker

Disconnector Switch

Transformer

Generic Module


13/17


• Add / Configure a Transformer1) Transformer module can be added at Transformer or Generic Bay level inElectric hierarchy.


Transformer Type :- Auto wound : no galvanic isolation between HVand LV sides, tap changer acts simultaneously inprimary and secondary : TAP RAISE = LV LOWER - Double wound : galvanic isolation between HVand LV sides, tap changer acts in primary : TAPRAISE = LV RAISE

2) Transformer attributes


Power value / impedance :AVR


14/17


• Transformer Configuration (1)1) Transformer basic configuration

Tap Changer built-in function:cf. DATAPOINTS CONFIGURATION course

Typed Raise/Lower DPC :Tap Change control

Typed TPI MV :cf. DATAPOINTS CONFIGURATION course


15/17


• Transformer Configuration (2)2) Transformer enhanced configuration => possible sons

Typed Goto min/max DPC :DPC doing raise until max tap / lower until mintap

Typed MCB Open SPC :- AVR

- In case of invalid tap changing, it will stopsupplying tap changer (power cutting)

Typed Higher Position / Lower Position SPS :

- SET when max tap and min tap are reached

Typed TAP Select SPC :when SBO, activated at selection

Typed Tap in progress SPS :- physically acquired by C264 - impact on control sequence


16/17


• Content

Circuit Breaker

Disconnector SwitchTransformer

Generic Module


17/17


• Features1) Generic Modules are :- non typed modules- contains generic datapoints - huge range of use => non particular context

- ADVISE : DON’T USE GENERIC MODULES for CB and disconnector if youhave :

- Built-in automation (AVR, Synchrocheck, Autorecloser)

- lock, hardware selection, withdrawn

Example for switching device

L2 V4 04 Basic Modules Configuration E 01

Documents

Transcript of L2 V4 04 Basic Modules Configuration E 01