Kverneland Cultivator CLC pro Classic and CLC pro Cut

Product information 2016

Kverneland CLC pro ClassicLighter 3 bar cultivator

Kverneland CLC pro CutWork even with long residues

CLC pro ClassicCLC proR:3.00m - 3.50m - 4.00mF:4.00m - 4.50m - 5.00m

R: 3.00m - 3.50mF: 4.00m - 4.50m - 5.00m

Only levelling tines on armsFull accessory range on parallelogram

CLC short tines

3

2

1810mm

810mm

CLC proRange overview

CLC pro Cut

CLC short tines CLC short tines

R: 3.00m -3.50mF: 4.00m – 4,50m

Cutting discs and only levelling tines on arms

• Higher versatility with 3 rows Better dispatching of the residues through

the working width and depth Better incorporation, no line of straw

disturbing seed to soil contact in min till process

Effective deeper cultivation possible without creation of a pan (to be highly considered in min till operations)

Intensive mix in the top layer offering ideal profile

Aerobic bacteria can process the residues in a better way into organic material for plant profit

• Better top layer profile with ideal seedbed for good rooting and plant development by access to manure

CLC pro Classic – 3 rows

CLC pro Classic• The CLC pro in its Classic variant is

offering 5 working widths to the lower power tractor segment with rigid models 3,0 - 3,50m and 4,00m-4,50m-5,00m folding

• The frame design is the same as the “pro” model but the rear equipment are based on roller arms holding a levelling tines bar in front of the roller

• Max power for the 3,00m is then 160hp

• Very compact and light design allowing tractors from 80hp to handle a CLC pro easily

• the Full roller program is available for this Classic version

CLC pro Cut• The CLC pro in its Cut variant is

offering 4 working widths to the lower power tractor segment with rigid models 3,0 - 3,50m and 4,00m - 4,50m folding

• The frame design is the same as the “pro” model but the rear equipment are based on roller arms holding a levelling tines bar in front of the roller

• The front cutting discs are hydraulically adjustable and are used to cut the long and avoid any blockages inside the machine

• Max power for the 3,00m is then 240hp

• The full roller program is available for this Cut version

CLC pro Classic and Cut– specific levelling device

• The parallelogram is replaced by a pair of arms just a bit longer than the standard ones to leave enough room between the tine and the roller to do a good levelling

• The levelling tine bar is linked to the roller frame, so changing depth will not alter the levelling quality

• Fine tuning of the tine position to the ground is done by an infinite screw adjustment

• The tine bar can be adjusted in 3 height position

CLC pro Classic and Cut – Rigid frame

• CLC pro range: Higher horse power ability More compact (81cm beam spacing) 2 tines options and their share equipment Compact levelling system and packing equipment available Tine spacing on CLC pro Classic 280mm - CLC pro Cut 380mm

• Rigid frame : 3,00m - 3,50m • Available for tractors up to 270 hp• New linkage concept with bolted headstock• Cutting discs on CLC pro Cut when long residues• Better stress dispersing after FEM calculation

CLC pro Classic and Cut – Fold 3 rows

• CLC pro folding Classic and Cut range as 3-bar is completing the new range a more compact solution with the accessories closer to the tractor

• The folding range is built up with the same principal as the rigid one Higher horse power ability – 200x200 mm cebntral frame Folding models 4,00 – 4,50 – 5,00m (Classic) and 4,00 – 4,50m (Cut version) More compact (81cm beam spacing) 2 tines options and their share equipment Compact levelling and packing equipment available Cutting discs on CLC pro Cut when long residues

CLC pro Classic CLC pro Cut

FEM calculation• The Finite Element Method is a computer simulation

helping to design each element according to the data and is securing the first step of the development.

Shaking test• at full load on a shaking robot during a specified

period• replicate the machine lifetime over few weeks to

control de reliability of the structure

The 3 critical phases of a frame development

Benefit:

We are using this know-how for all our new products. In parallel, a protocol of functional tests is managed in various countries to collect farmers opinion. We are investing a lot to guarantee the best performances.

Strain gauge test• physical tests in the field and in transport by using

strain gauges which can register the real stress in the material.

• By cross-checking with the 2 previous phases the structure maximum power allowance can be approved

CLC tine – Bolted tine holder

The CLC line is getting as a standard the bolted tine holder for all models.

Benefit: easy to take few tines away when

using the CLC models as loosener less welding on main frame is more

reliable and giving the all structure a longer life time.

CLC tine – High clearance

870.

mm

• the high under beam clearance of 870mm is ensuring blockage free operation

• well proven simple and robust design with no grease nipple at all = low maintenance (due to heat treatment by cementation no wearing between the parts, no greasing necessary)

• Unique leg design made out of a tube enabling the C shank to move side ways +/- 14 cm with the short tine, and +/-20 cm with the long tine, each side, thus reporting less stress to the structure

• light weight concept, complete tine is only 35kg.

• User friendly technology

CLC tine – Maintenance free zone

70x40mm

• Always the best penetration ability in all soil

• The power demand and the fuel consumption are limited.

1. point is working by lifting the ground to make a perfect cracking of the top layer

2. the upper part is doing an intensive mixing also with low power demand due to its receding shape.

Benefit: This particular angle design offering 2 distinct

front lines is avoiding to flick poorer soil back on top of the ground, interesting when such cultivator equipment will be used for preparing seedbed in one pass.

CLC tine – Special angle

α

1

2

• All parts of the tines are heat treated, providing

an extraordinary reliability and long life• Extraordinary vibration capacity providing

intensive crumbling.

• Unique leg design made out of a tube

enabling the C shank to move side ways +/- 14 cm

with the short tine, and +/-20 cm with the long tine,

each side, thus reporting less stress to the structure

• This technique is also allowing to use lighter

material, in order to save lifting capacity and

pulling requirement

• Here is a tine in our laboratory showing how far it can flex. The side pulling force to go up to 20 cm is 1,200kg. The tine holder stays in place, just the leg is flexing due to the heat treated tube

CLC tine - Flexibility

CLC tine - Flexibility

Benefit: Higher pressure, at 5cm for a total of 640.kg interesting when

hard dry soil Frame protected all the time Unique on the market : the release force decreases when the

release height increase

CLC tine – Auto-reset

CLC tine – Light Auto-reset (option for Classic model)

• As the Classic model is designed for lower power range, an optional lighter leaves spring pack is available.

• 450.kg will be enough in lighter soil to keep the point at a constant depth. (this pressure is also corresponding to a good average available on the market)

• Benefit: lower price lighter machine more leaves can be retrofitted if necessary

The shear bolt leg design is providing a Vibromat effect

Benefit:

higher pressure at the point with 2T to ensure a clean breaking of the bolt

Vibromat effect: the tine being made from a tube is flexible enough to allow the point to trip 10 cm back before the bolt is breaking. In that way the Vibromat is is avoiding too frequent breakage even being only shearbolted

This short tine can still go 14cm sideways around obstacles, reporting less stress to the tine holder and frame

Shearbolt and Leaf spring pack can be combined, so that the spring pack will get 2T pressure also before releasing, interesting in very heavy soils to keep the tines in and avoiding the driver to change the bolt immediately.

longer life time

CLC tine – Shear bolted leg

CLC tines: high quality and low cost wearing parts made

in Kverneland

Standard share 60mm

• reversible plough share

• low cost

• quality heat treatment

Standard share + 300mm wing

• adapted to shallow working depth

• good boiling effect

• quality heat treatment

CLC tine – Bolted shares

• Multiple combinations of shares and deflectors can be fitted to the CLC tine to get

optimum result whatever the soil conditions.

• Full range of shares available to match with all tine spacing from 200 to 345 mm

• Easy adptation to depth to minimize fuel consumption

• Only a hammer and a wedge needed

• Get more details in the separate Knock-on Presentation

KO 80

CLC tine –

KO 150 KO 250 KO 320

Fast and easy metal

change

10’’

Quantum 345mm + KO 80

• 2 dimensions : 80mm and 150 mm• Compatible with all Knock-on deflector and Quantum share

345mm• Exteremely long life • Resist against stony conditions• Low power consumption required due to the progressive shape

CLC tine – Carbide equipment

Dorset Tiger point 80mm

Dorset Tiger point 150mm

CLC pro Cut – Discs equipmentDouble disc gang 510 mm• Position controlled with pins• Parallelogram to obtain the best possible work• Easy angle adjustment with bolts.• Does a good mixing and incorporation• Not compatible with rollers• Leaves a rough surface with aggregates ready for wintering,

interesting at the end of autumn season for preparing spring fields and crops

New Combi disc:• Combination of a single disc gang with all roller type• intensive mixing and incorporation, well adapted to high amount of residues• Very good levelling capacity• Hydraulic setting of the disc gang• Pair of border disc as standard• New bearing holder clamped to the beam to slide gangs for fine

tuning• New angle adjustment allowing full depth of the parallelogram system

Actipack roller 560 mmMake it as aggressive as you want

• Skid and knives between discs clean even in wet conditions. The knives are cutting bigger clods coming in the disc spacing of 12,5cm leaving a ready seedbed

• Knives pressure can be adjusted as high as the disc pressure to the ground to make equal pressure through the working width to achieve a nice and firm seedbed, and can also be put in a non working position to leave a rough ground surface with more clods (weather protected)

• 3 different positions of the knives aggressiveness are proposed + 1 “OFF” position. They are adjusted thanks to the long spanner

• Can work with or without knives• No limitation in stony conditions• Discs with aggressive notched shape to ensure good driving

CLC range – Rollers

• Maintenance free bearings with 5 lips labyrinth sealing system + steel protection cover

Actiring roller ø 540mm

• Light and active due to the skids between the rings that avoid blockages.

• The knives are cutting bigger clods coming in the disc spacing of 12,5cm leaving a ready seedbed

• Ring made with L profile.• Light and strong construction• Good recompaction (160 kg/m)• Shaft diameter: 50 mm

Unique knives pressure adjustment

• Knife pressure can be adjustable to ensure a fine crumbled seedbed or rough surface

• 3 different positions for the knives pressure are available. They are adjusted thanks to the long spanner delivered with the machine

CLC range – Rollers

• Maintenance free bearings with 5 lips labyrinth sealing system + steel protection cover

CLC range – RollersActiflex roller ø 580mm

• Intensive mixing effect• Self-cleaning effect• Low sensibility to blockages and stony conditions• Good compromise between recompaction and cost

(160kg/m)• For all soil types• Maintenance free bearings with 5 lips labyrinth sealing

system + steel protection cover• Low sensibility to wearing soil• Shaft diameter: 50 mm

New Double cage roller 400 mm (tube/flat)• Good crumbling• Precise depth control• Good levelling effect• Good carrying capacity• New robust frame and suspension design

CLC range – Rollers

Cage roller 550 mm• 10 bars for a good loading capacity• Effective crumbling action• Economic roller• For light to medium soil• Shaft diameter : 50 mm• Weight : 90kg/m

• Maintenance free bearings with 5 lips labyrinth sealing system + steel protection cover

Wheels 600x9 (540x160) on rigid models• AW profil AW for better cleaning• high load capacity (10-PR)• high resistance to punches• valve is protected• setting with sliding arm and pin

Wheels 10.0/80-12 (710x274) on folding models• AW profil AW for better cleaning• high load capacity (10-PR)• high resistance to punches• good carrying capacity • valve is protected• infinite screw adjustment

CLC – depth controlEquipement recommanded when use of double disc gang option, and from 4,50m working width

CLC pro Cut and Classic – Technical data

Models CLC pro 300 CLC pro 350 CLC pro 400 CLC pro 400 CLC pro 450 CLC pro 500

Number of tines CLC pro 10 12 14 13 15 17

Number of tines CLC pro Classic 10 12 - 13 15 17

Number of tines CLC pro Cut 7 9 - 11 13 -

Working width (m) 3,00 3,50 4,00 4,00 4,50 5,00

Transport width (m) 3,00 3,50 4,00

Row spacing (mm)Frame box section (mm)LinkageUnderbeam clearance (mm)Average tine spacing (mm) CLC pro 280 280 280 290 290 290

Average tine spacing (mm) CLC pro 280 280 - 290 290 290

Average tine spacing (mm) CLC pro 420 385 - 350 350

Min/Max HP CLC pro 120/240 135/270 165/300 185/300 190/325 200/350

Weight (Kg) CLC pro Claasic SB* + levelling tine + Actiring 1420 1640 - 2400 2770 2960

Lifting capacity (t) CLC pro Classic SB* + Levelling tine + Actiring** 3,9 4,3 - 5,9 6,8 7,3

AR* = Auto-Reset / SB* = Shear Bolt** Consider -15% if cage roller/ equal for Actiflex/+15% for Actipack or double disc gang

870

810100x100

Cat II & III

Models CLC pro 300 CLC pro 350 CLC pro 400 CLC pro 400 CLC pro 450 CLC pro 500

Number of tines CLC pro 10 12 14 13 15 17

Number of tines CLC pro Classic 10 12 - 13 15 17

Number of tines CLC pro Cut 7 9 - 11 13 -

Working width (m) 3,00 3,50 4,00 4,00 4,50 5,00

Transport width (m) 3,00 3,50 4,00

Row spacing (mm)Frame box section (mm)LinkageUnderbeam clearance (mm)Average tine spacing (mm) CLC pro 280 280 280 290 290 290

Average tine spacing (mm) CLC pro 280 280 - 290 290 290

Average tine spacing (mm) CLC pro 420 385 - 350 350

Min/Max HP CLC pro 120/240 135/270 165/300 185/300 190/325 200/350

Weight (Kg) CLC pro Claasic SB* + levelling tine + Actiring 1420 1640 - 2400 2770 2960

Lifting capacity (t) CLC pro Classic SB* + Levelling tine + Actiring** 3,9 4,3 - 5,9 6,8 7,3

AR* = Auto-Reset / SB* = Shear Bolt** Consider -15% if cage roller/ equal for Actiflex/+15% for Actipack or double disc gang

870

2,85810

100x100 Central 200x200 - External 100x100Cat II & III Cat III & IV

CLC pro Classic and Cut : Main advantages

• High Horse power capacity to cope with all conditions and tractor sizes from 90 to 350 hp

• Universal Cultivator from 3.0 to 5 m, working 5 to 30cm deep• The Classic version is the right answer to small tractors• The Cut version can work with long residues for a better soil flow management• 3 bar frame and/or cutting disc+ 2 bars for optimum mixing and blockage free

operation• Unique leg design protecting the structure and no maintenance• Unique leg design vibrating for intensive effect in the soil but low fuel consumption• Knock-on system for fast and easy metal change• Wide choice of rear roller and leveling equipment• Intensive mixing of the residues• Low power requirement• Seedbed finish possible

Kverneland CLC pro Classic

Power optimistic!

CLC pro Classic - 300/Levelling tines /Actiring

CLC pro Classic - 400F/Levelling tines /Actiring

CLC pro Classic - 300/Levelling tines /Double cage roller/a-drill

CLC pro Cut – 4,50m - Cutting disc action

 

 

 

See ourMachines

at workon YouTube

www.kverneland.com

visit us at www.kvernelandgroup.com

The Future of Farming