KingNeed Auto Jumper Starter
-
Upload
gpspro -
Category
Technology
-
view
46 -
download
0
Transcript of KingNeed Auto Jumper Starter
PatentedBK180
New Revolution Backstage operation at every ignition Say goodbye to ‘Traditional’ Starter
Auto Jump Starter
Battery Keeper
No help for battery. Even jump starter works well, battery still need to be renew after the indignation.
Complicated to use. The engine hood need to be open, and battery positive and negative side need to be connected correctly every using the jump starter. It is too hard to use for ladies and elders.
Unsafe. Sparks can be triggered during storage and use. It is unsafe especially for ladies and elders.
Not reliable. Jump starter battery need to be recharged on time. What frequently happens is finding out there is low battery in the Jump starter when you need it in a hurry.
The Problems of Traditional Jump-Starter
New Series
BK186BK184BK182
New Series
BatteryCapacity
PeakStarting Current
Support Engineer Capacity
Support Engineer Capacity
When Voltage of car battery drop to 8V
When Voltage of car battery drop to 0V
BK180 1800mA 150A max 2.0 liters max 1.5 liters
BK182 2000mA 180A max 2.2 liters max 1.8 liters
BK184 4000mA 320A max 3.0 liters max 2.8 liters
BK186 6000mA 480A max 4.3 liters max 4.0 liters
Battery Type: Lithium Titanate battery Standby Time: 3-6 months
Automatic, backstage operation at every ignition Prolong 1-5x life time of car battery, even for new battery -25 degree, Jump starter Stable, Fixed installation on the surface of Car Battery Safety, Built-in MCU control, it still safe even the positive and negative connected Easy drive, no more battery concern, especially for elders and ladies.
Battery Keeper automatic backstage operation at every ignition, user don’t need to open the engine case to jump-start the car since MCU automatically control the charging and engine start process It can much better prolong the car battery life because battery output for the engine start is much lower with the keeper’s help. Even when a dead battery with voltage lower than 10V, it could still working well with the help of battery keeper. The battery keeper can be fixed firmly on the top of car battery with cables and sticker. About the safety, the Lithium titanate is the safest battery which is used widely in electric car field, with MCU control current protection. Water proof design with compact size: 150*84*44mm
Features
Perfect solution for taxi
Battery Keeper is a perfect solution for taxi, because of the frequent engine start daily, original car battery usually die quickly.
Installation Location 1
System will start initialising when device is first connected to battery. When both red and green LED flashing for 30 seconds indicating system is in working mode.
Once ignition is detected system will discharge pulse current to help the car starts. Green light will be on when device is working. Battery keeper will be full charged during driving. Red light will be on when charging and turns off when full charged.
Operation Guide
Operation Video Link http://youtu.be/GwiL3lMiku0
Installation Location 2
Installation Location 3
Package
Super Safety Lithium Battery
• Safe: There won’t be any explosion triggered even with direct short circuit, reverse direction charging, needle puncture, or hit forcefully.
• Wide working temperature range working well between -25 to 70 ℃
• Extra long battery life: Over 1500 times charging cycles in high rate charging mode; Over 5000 times charging cycles in normal rate charging mode
• Fast Charge: 5-20C fast charge.
• High Discharge: Maximum 100C fast discharge
Super Safety Lithium Battery
Test Project Battery Status Test way Result
Acupuncture test Fully Charged
push 3mm diameter of the needle as 10mm-40mm / s of speed through the center of the cell, needle left in the battery
Pass, No explosion, no fire
Test Project Battery Status Test way Result
Squeeze test Fully ChargedThe battery placed between the plates, then squeeze it with the greatest pressure 17.2Mpa
Pass, No explosion, no fire
Test Project Battery Status Test way Result
Impact Test Fully Charged Drop a 9.1 Kg weight from 610mm high to impact the test battery
Pass, No explosion, no fire
Test Project Battery Status Test way Result
Drop Test Fully Charged
The test cell consists of a height of 1000mm placed in the position of free fall to the horizontal plane 18mm thick hardwood board, From the direction of X, Y, Z in the three axes a drop
Pass, No explosion, no fire
Test Project Battery Status Test way Result
Overcharge Test Fully ChargedCharg the test battery which is fully discharged to 10V voltage with 3C charging current
Pass, No explosion, no fire
Test Project Battery Status Test way Result
Short Test Fully Charged
The test battery shorted directly with positive and negative resistance <100mΩ wire, After the battery is fully discharged, and the temperature of outside case dropped to room temperature, the test stops
Pass, No explosion, no fire,this temperature of outside case is below
150 degree
Test Project Battery Status Test way Result
Heating Test Fully Charged
Put the test battery into programmable temperature and humidity chamber and heat to 150 ° C for 10min
Pass, No explosion, no fire