k o l b eC - Hass Wholesalehasswholesale.com/PDF_6_12/K-K_brochure_Classic.pdf Glass options DiviDeD...
Transcript of k o l b eC - Hass Wholesalehasswholesale.com/PDF_6_12/K-K_brochure_Classic.pdf Glass options DiviDeD...
See the Difference Quality Makes®
k o l b eCl a s s i C se r i e s Pr o d u C t Cata l o g
� ClassiC series
�www.kolbe-kolbe.com
The Classic Series is Kolbe’s line of roll-formed aluminum clad
wood windows. This series features simple, uncomplicated lines to
complement any style of design.
Create a grand entrance with an outswing door and sidelites with
custom grilles. Brighten a design with curves from a full circle, half-
circle or elliptical radius window. Kolbe® products are made with
utmost care and attention to detail in mind.
Kolbe is committed to designing and constructing the highest quality windows and doors possible, while
utilizing our natural resources in a safe and efficient way. Most of our products contain some recycled
materials, while we find ways to reuse and recycle items within our company. By using our products with
other eco-friendly materials, they in turn can help lead to a greener home or business.
By associating with NFRC, Window and Door Manufacturers Association Hallmark Certification
Program and the Energy Star Program, Kolbe products are built to meet the diverse and expanding needs
of residential and commercial fields. Such tests measure air and water infiltration, structural performance
and energy efficiency. Rest assured that Kolbe products are tested in an unbiased manner by independent
laboratories and that test data is available to the public. (See Technical Data section on pg. 101.)
C l a s s i C s e r i e s O v e rv i e w
�
� ClassiC series
C l a s s i C s e r i e s F e at u r e s a t a G l a n C e
Casements & Awnings
Traditional Double Hungs
Double & Triple Sliders
Rectangular Transoms
Radius Windows
Geometric Windows
Viewport Sliding Patio Doors
Garden-Aire Sliding Patio Doors
Inswing Patio Doors
Inswing Entrance Doors
Outswing Entrance Doors
S O O O S O O
S O O O S O O
S O O O S O O
S O O O S O O
N/A* O O O S O O
S O O O S O O
S O O O S O S
S O O O S O S
S O O O S O S
S O O O S O S
S O O O S O S
Rol
l-for
med
Alu
min
um C
ladd
ing
Gril
les-
in-t
he-A
irspa
ce
Woo
d R
emov
able
Gril
les
Per
form
ance
Div
ided
Lite
s (P
DL)
H°K
LoE
2 -
270
exterior Finish
H°K
LoE
2 -
240
or L
oE3 -
366
S = standard
O = option
N/A = not available
Tem
pere
d G
lass
* Note: Radius windows use extruded aluminum cladding instead of the roll-formed aluminum cladding.
DiviDeD lites Glass
�www.kolbe-kolbe.com
Glass options
DiviDeD lite options
Finish options
other options & aCCessories
Casements
awninGs
Double hunGs
sliDers
patio Doors
entranCe Doors
Complementary
teChniCal Data
Co
nt
en
ts
6
7
8
9
11
39
47
59
63
75
89
101
table oF
Contents
This catalog is intended to show options available. Pricing within standard and custom options may vary. Please contact a Kolbe dealer for details.
� ClassiC series
H˚K LoE²-270
H˚K LoE³-366
Laminated IG
H°K LoE²-240
86%95%
99%
UV BLOCKAGE
84%
G l a s s O p t i O n s
tempereD
Safety standard in Kolbe doors. Essential to meet some
building requirements.
laminateD
Provides the ultimate in UV blockage.
(See illustration above)
h°K loe2 - 240
A tinted glass recommended for warm climates that
achieves solar control over a wide range of the
spectrum, while also helping to reduce glare.
H°K LoE� -���
Recommended for all climates, with maximum protection
against heat loss and UV damage.
bronze or Gray tinteD
Provides shading to interiors.
patterneD or ColoreD
Creates visual interest to any window or door. Also provides
privacy to rooms.
preserve
Preserve film is available on windows and doors to help keep
the glass clean and debris free. The film is applied to the
interior and exterior of the unit, protecting it through travel,
installation and in field finishing. Any mess stays on the film,
which is easily removed once the job is completed.
NOTES:LoE�, LoE�-�70, LoE� -��0, LoE�-��� and Preserve are trademarks of Cardinal IG.
H°K insulating glass carries a �0-year warranty. Not all glass options listed have the same glass warranty. Please contact your supplier for details.
G l a s s O p t i O n s
H ° K G l a s s : s u p e r i O r a s s ta n d a r d
Kolbe believes that quality is in the details. That is why we insist
on using a glazing system to achieve optimum energy efficiency of the
overall window unit. We use double-strength annealed glass in most
units, with double-pane insulating H°K LoE�-�70 glass as standard. We
also offer glass options that are common to the industry, as well as meet
many specialized glass requests.
H°K glass has LoE�, “smart” coating that reduces energy transfer
through the insulating glass unit. The performance of LoE� glass is
achieved through a sputter coating process. The coating achieves one
of the highest levels of energy performance possible. This process is
also environmentally sound. It creates no emissions or residues. In
summer, LoE� glass allows visible sunlight in while blocking 9�% of the
sun’s infrared heat energy, while in winter LoE� glass reflects roomside
heat back into the room. The result is significant savings in heating
and cooling costs throughout the year. LoE� glass also selectively
filters out 8�% of the sun’s harmful ultraviolet rays, which provides
protection against the fading of furniture, fabrics and carpeting.
To further boost energy efficiency, H°K glass is filled with argon
gas. This natural, existing gas is colorless, odorless, non-toxic,
non-corrosive and non-flammable. Its thermal conductivity is �0%
lower than that of air. Together, the LoE� coating and argon gas result
in a �1% improvement in U-factors and a 10�% improvement in
R-values, as compared to air-filled insulating glass without LoE�.
What’s more, because units with argon are assembled in vacuum
chambers, they do not require unsightly plugs in the spacer bars.
To maintain the integrity of the product, units to be installed in or
shipped through high altitude areas may not include argon gas.
H°K glass is complemented by a state-of-the-art, stainless steel
spacer bar system on most units. These Thermo-Edge units achieve low
heat conductance throughout the edge seal design. The primary seal
of the dual-seal construction is compressed polyisobutylene, while the
secondary seal is silicone. In addition, desiccants are enclosed within
the stainless steel spacer to absorb moisture and the spacer corners
are bent to be air/gas tight. This improves the overall U-factor of the
window and can reduce the potential for condensation by increasing
the roomside glass temperature at the frame/glass interface.
Thermo-Edge spacers are one of the many quality details that define
Kolbe windows and doors.
NOTE: Tested units include argon. The laminate has 1/�" inner pane. Based on Lawrence Berkeley Lab (LBL) Window �.� © �00� analysis for classical UV transmission data.
7www.kolbe-kolbe.com
d i v i d e d l i t e O p t i O n s
G r i l l e s - i n - t H e - a i r s p a C e
w O O d r e m O va b l e G r i l l e s
Wood grilles are built with a full surround frame and bars that interlock at the joints for stability.
Grilles are applied to the interior of the window using an exclusive hidden clip system*. This system
makes unsightly pins and attachment points unnecessary and removal or replacement easy. Grille
bars are profiled on the interior like traditional grilles with detailed grooves on the exterior for subtle
depth and richness. As standard, bars are constructed of unfinished pine and are 7/8" wide on windows
and 1-1/8" wide on doors. Custom grille patterns, bar widths, wood species and interior stains may
be available upon request.* A clear pin system will be used for Garden-Aire sliding patio doors, and grilles will not have accent lines on the bar exterior.
Grilles-in-the-airspace are constructed with aluminum bars sealed between two panes of H°K
insulating glass, offering the look of divided panes while reducing cleaning time. For units with
7/8" insulating glass, contoured, �/�" wide bars are standard in White, Beige, Sand, Rustic, Hartford
Green and Chutney. Optional colors are light wood and dark wood faux finishes. Flat, �/8" wide
grille bars are also available in White, Beige, Sand, Rustic, Hartford Green, Chutney, light wood and
dark wood faux finishes and Brass. Two-tone contour or flat grilles are available with either light or
dark wood faux finishes to the interior and White to the exterior. Also available for 7/8" insulating
glass are �/1�" wide brass “pencil” bars.
contour bars
flat bars & brass “pencil” bar
p e r F O r m a n C e d i v i d e d l i t e s
Kolbe’s performance divided lite (PDL) glazing system gives the appearance of true divided lites
without sacrificing energy efficiency. A single, H°K insulating glass unit is used, while aesthetically
pleasing spacer bars are installed within the insulating glass unit. Extruded aluminum bars are adhered
to the exterior of the glass and unfinished pine bars are adhered to the interior of the glass.* Together,
these bars create the illusion of true divided lites. PDL bars are available in �/8", 7/8", 1-1/8",
1-�/�" or �-1/�" bar widths. The exterior finish of the aluminum bars will match the exterior finish on
the unit. Variations on the PDL option may include custom grille patterns, bar widths or no spacer bars.
* Some intricate radius designs may have a composite material for the exterior PDL bar.
8 ClassiC series
a l u m i n u m C l a d d i n G
Classic Series clad products are coated with a polyester finish that is baked to
cure and harden on the aluminum surface. This helps the finish resist marring and
fading, while increasing weatherability. The polyester finish carries a �0-year warranty
against cracking, checking and peeling. Classic Series clad windows and doors are
available in five standard colors.
F i n i s H O p t i O n s
White Beige Sand
Rustic Hartford Green
p O ly e s t e r F i n i s H e s
i n t e r i O r p r e F i n i s H i n G
Kolbe windows and doors are unfinished as standard.
Interior prefinishing is offered with two coats of a
water-based, acrylic type white paint. All windows
and Garden-Aire sliding patio doors will be coated
with latex primer. Inswing and outswing doors will
be coated with a high performance urethane primer. (Primer
is not available on grilles.)
i n t e r i O r w O O d O p t i O n s
In addition to the standard pine, Kolbe offers other optional
wood species to enhance the look of a window or door unit.
The wood species available are mahogany, oak, fir, alder,
walnut, maple and cherry. Contact your Kolbe dealer for
more details.
C O p p e r C l a d d i n G
Enhance the aesthetic appeal of your windows and doors
with copper cladding. Over time you will discover the
hidden beauty when it develops a natural patina.
9www.kolbe-kolbe.com
O v O l O G l a z i n G b e a d s & m u n t i n b a r s
As standard, glazing beads have a beveled profile, but may also
be ordered with an ovolo profile. To complement ovolo glazing
beads, ovolo muntin bars are available on units with PDL and
removable wood grilles. Units ordered with PDL will have
ovolo muntin bars on the interior and beveled muntin bars on
the exterior. (See grille cross section drawings on pgs 98-99.)
O t H e r O p t i O n s & a C C e s s O r i e s
i n t e r i O r C a s i n G
Accent the interior of windows and
doors with interior casing by Kolbe.
As standard, choose either �-1/8"
wide ranch casing or �-1/�" wide colonial casing. Ranch and
colonial casing are available in unfinished pine or oak, ready
for paint or stain. Curved radius casing is available as well, to
match the curves of Kolbe radius units.
Specialty mouldings are available in pine, oak and other
wood species. Shipped loose for field application, specialty
mouldings are available in a wide variety of profiles.
Ranch Colonial
s t O r m G u a r d
Kolbe’s durable StormGuard combination storm/screen
units provide extra protection from the elements. Units
feature two glass inserts and one screen insert that can
be removed from the interior for cleaning. Frames are
constructed of extruded aluminum made of a lightweight
alloy, which is easy to handle without sacrificing
performance. Weatherstripping along the top and sides
of all three inserts ensures a tight fit that will withstand
harsh weather. Weep holes channel water out to help
prevent damage to the window sill. The sight lines and
profile of StormGuard units closely match the window it
complements, which means the unit will blend in and your
view will not be obscured. Screen inserts have fiberglass
mesh as standard; aluminum mesh is optional. StormGuards
for Classic Series windows are available in White, Beige,
Sand, Rustic and Hartford Green.
Double Hung StormGuard
in White
Slider StormGuard
in Beige
s w i n G i n G s C r e e n d O O r s
Swinging screen doors are available
for field installation with Kolbe single
and double inswing doors. Screen
doors feature an adjustable self-closing
mechanism. Double swinging screen
doors are equipped with spring-loaded
locking mechanisms on the head and
sill of the passive door. Energy efficiency
is provided by weatherstripping around the frame perimeter
and on the astragal of double screen doors; rubber door sweeps
meet the sill.
Beveled Profile
Ovolo Profile
Wood Removable Grilles
10 ClassiC series�8 Kolbe winDows & Doors
CasementsCasements
stuDio & transom units piCture Combination units bow & bay units
11www.kolbe-kolbe.com
Gl a s s:➢ H°KLoE2-240*
➢ H°KLoE3-366*➢ Patterned-,bronze-orgray-lite➢ Temperedorlaminated➢ Otheroptionsstandardtotheindustry
Gr i l l e s :➢ Grilles-in-the-airspace➢ Interiorremovablewoodgrilleswith7/8"or1-1/8"barsand fullsurrounds➢ PDLwith5/8",7/8",1-1/8",1-3/4"or2-1/4"bars
Ot h e r Op t i O n s: (notalloptionsareavailableonallcasementtypes)
➢ Otherwoodspecies➢ Ovoloprofileglazingbeadsandinteriorgrillebars➢ Interiorprefinishing➢ Interiorcasing
➢ Prepforstool➢ Hardware,multi-pointlocksandoperatorcoversinWhite, Beige,Brassandcustomfinisheslistedabove➢ Single-armoperatorswithEurohinges(meetsemergencyescape
andrescuerequirementsonsome“L”Seriescasements)
➢ ScreenswithWhite,Beige,orBrassframes(Brassframesarenot
availableonradiustopunits)
➢ Screenswithaluminumorcharcoal-coloredaluminummesh (excludingbrassframes)
➢ Woodwrappedscreens(notavailableonradiustopunits)
➢ Extensionjambs(upto12"applied,over12"shippedloosefor
fieldapplication)
➢ Bowandbayoptions:insulatedplatforms,supportbracketsand oak-veneeredheadandseatboards
C a s e m e n t O p t i O n a l F e at u r e s
NOTES:
Allmeasurementsarenominal.
*Argongasmaynotbeincludedwithunitstobeinstalledinorshippedthroughhighaltitudeareas.
h a r d wa r e
Clay-colored, folding handles are applied to casement units as standard.
Standardcasementhandlesarealsoavailable inWhite,BeigeandBrass.
Custom finishes include Antique Brass, Satin Nickel, Antique Nickel,
MatteBlack,Oil-rubbedandRusticUmber.Multi-pointlockhandleswill
matchoperatorhandlecolors.
C l a s s i C s e r i e s C a s e m e n t s
C a s e m e n t s ta n d a r d F e at u r e s
➢ 1-3/4"thicksash
➢ Overalljambwidthis4-9/16"(basicboxwidthis2-7/16",
plusextensions)
➢ Constructedofpine,withpineinteriorstopsandwoodmull
casingsonmulledunits
➢ Prefinished,heavygaugeroll-formedaluminumcladding
➢ 7/8"H°KLoE2-270insulatingglass*
➢ Glazedtotheinteriorwithwoodglazingbeads
➢ Allexteriorwoodpartsarepreservative-treated
➢ Fullyweatherstrippedforatightseal
➢ InteriorscreenswithClay-coloredaluminumframesand
charcoal-coloredfiberglassmesh
➢ Clay-coloredfoldinghandles,operatorcoversand
multi-pointlocks
➢ Dual-armoperatorswithconcealed,adjustablehinges
(single-armoperatorswithconcealed,adjustablehingeson“S”Series
casements;single-armoperatorswithEurohingesforaddedsupporton
segmentheadandhalf-circletopunit)
➢ Stainlesssteelexterioroperatorparts
➢ Heavyvinylnailingfin
➢ Pine-veneeredheadandseatboards;unique,narrow
mullionsandcablesupportsystemonbowandbayunits
Vinylnailingfinappliedasstandard
foldinghandleinClay(closed)
foldinghandleinClay(open)
1� ClassiC series
1'-8"1'-8 1/2"15 1/4"
N12
N13
N14
N15
N16
N156
N146
N136
N126
2'-6"2'-6 1/2"25 1/4"
X12
X13
X14*
X15*
X16*
X156*
X146*
X136
X126
3'-0"3'-0 1/2"31 1/4"
E13
E14*
E15*
E16*
E156*
E146*
E136*
Casements - single units
L12
L126
L13
L136
T14
L146
L15
L156
L16
2'-4"2'-4 1/2"23 1/4"
1'-4"1'-4 1/2"11 1/4"
F.s.r.o.
G.s.
S12
S13
S14
S15
S16
S156
S146
S136
S126
2'-0
"2'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
2'-0"2'-0 1/2"19 1/4"
W12
W13
W14
W15
W16
W156
W146
W136
W126
C l a s s i C s e r i e s C a s e m e n t s
C a s e m e n t s s i n G l e u n i t s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
* Units meet most national emergency escape and rescue requirements.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCE1�). Specify stationary, left or right venting when ordering single units. Venting is viewed from the window exterior.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
D i m e n s i o n C a l C u l a t i o n s
F.S. to Sash O.S.M. -1 1�/1�" -1 1�/1�"Sash O.S.M. to G.S. -� 1�/1�" -� 1�/1�"G.S. to D.L.O. -1" -1"G.S. to Screen O.S.M. +1 9/1�" +1/�"note: Clear opening dimensions can be found on pg. 101.
F.S. = Frame Size • G.S. = Glass Size • O.S.M. = Outside MeasurementD.L.O. = Daylight Opening
wiDth heiGht
1�www.kolbe-kolbe.com
C l a s s i C s e r i e s C a s e m e n t s
1'-4"1'-4 1/2"11 1/4"
F.s.r.o.
G.s.
S12 S22 S32 S42 S52
S13 S23 S33 S43 S53
S14 S24 S34 S44 S54
S15 S25 S35 S45 S55
S16 S26 S36 S46 S56
S156 S256 S356 S456 S556
S146 S246 S346 S446 S546
S136 S236 S336 S436 S536
S126 S226 S326 S426 S526
2'-8"2'-8 1/2"11 1/4"
4'-0"4'-0 1/2"11 1/4"
5'-4"5'-4 1/2"11 1/4"
6'-8"6'-8 1/2"11 1/4"
2'-0
"2'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
Casements - “s” seriesC a s e m e n t s “ s ” s e r i e s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configurations shown for single sash are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCS��). Specify stationary, left or right venting when ordering single units. Venting is viewed from the window exterior.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
1� ClassiC series
F.s.r.o.
G.s.
2'-0
"2'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
1'-8"1'-8 1/2"15 1/4"
N12 N22 N32 N42 N52
N13 N23 N33 N43 N53
N14 N24 N34 N44 N54
N15 N25 N35 N45 N55
N16 N26 N36 N46 N56
N156 N256 N356 N456 N556
N146 N246 N346 N446 N546
N136 N236 N336 N436 N536
N126 N226 N326 N426 N526
3'-4"3'-4 1/2"15 1/4"
5'-0"5'-0 1/2"15 1/4"
6'-8"6'-8 1/2"15 1/4"
8'-4"8'-4 1/2"15 1/4"
Casements - “n” series
C l a s s i C s e r i e s C a s e m e n t s
C a s e m e n t s “ n ” s e r i e s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configurations shown for single sash are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCN��). Specify stationary, left or right venting when ordering single units. Venting is viewed from the window exterior.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
1�www.kolbe-kolbe.com
C l a s s i C s e r i e s C a s e m e n t s
F.s.r.o.
G.s.
2'-0
"2'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
2'-0"2'-0 1/2"19 1/4"
W12 W22 W32 W42 W52
W13 W23 W33 W43 W53
W14 W24 W34 W44 W54
W15 W25 W35 W45 W55
W16 W26 W36 W46 W56
W156 W256 W356 W456 W556
W146 W246 W346 W446 W546
W136 W236 W336 W436 W536
W126 W226 W326 W426 W526
4'-0"4'-0 1/2"19 1/4"
6'-0"6'-0 1/2"19 1/4"
8'-0"8'-0 1/2"19 1/4"
10'-0"10'-0 1/2"
19 1/4"
W62
W63
W64
W65
W66
W656
W646
W636
W626
12'-0"12'-0 1/2"
19 1/4"
Casements - “W” seriesC a s e m e n t s “ w ” s e r i e s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configurations shown for single sash are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCW��). Specify stationary, left or right venting when ordering single units. Venting is viewed from the window exterior.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
1� ClassiC series
C l a s s i C s e r i e s C a s e m e n t s
C a s e m e n t s “ l ” s e r i e s
F.s.r.o.
G.s.
2'-0
"2'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
2'-4"2'-4 1/2"23 1/4"
4'-8"4'-8 1/2"23 1/4"
7'-0"7'-0 1/2"23 1/4"
9'-4"9'-4 1/2"23 1/4"
11'-8"11'-8 1/2"
23 1/4"
14'-0"14'-0 1/2"
23 1/4"
Casements - “l” series
L12
L126
L13
L136
L14*
L146*
L15*
L156*
L16* L26*
L256*
L25*
L246*
L24*
L236
L23
L226
L22 L32
L326
L33
L336
L34*
L346*
L35*
L356*
L36* L46*
L456*
L45*
L446*
L44*
L436
L43
L426
L42 L52
L526
L53
L536
L54*
L546*
L55*
L556*
L56* L66*
L656*
L65*
L646*
L64*
L636
L63
L626
L62
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configurations shown for single sash are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
* Units meet most national emergency escape and rescue requirements when modified with single-arm operators and Euro hinges.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCL��). Specify stationary, left or right venting when ordering single units. Venting is viewed from the window exterior.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
17www.kolbe-kolbe.com
C l a s s i C s e r i e s C a s e m e n t s
F.s.r.o.
G.s.
2'-0
"2'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
2'-6"2'-6 1/2"25 1/4"
X12 X22 X32 X42 X52
X13 X23 X33 X43 X53
X14* X24* X34* X44* X54*
X15* X25* X35* X45* X55*
X16* X26* X36* X46* X56*
X156* X256* X356* X456* X556*
X146* X246* X346* X446* X546*
X136 X236 X336 X436 X536
X126 X226 X326 X426 X526
5'-0"5'-0 1/2"25 1/4"
7'-6"7'-6 1/2"25 1/4"
10'-0"10'-0 1/2"
25 1/4"
12'-6"12'-6 1/2"
25 1/4"
Casements - “X” seriesC a s e m e n t s “ X ” s e r i e s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configurations shown for single sash are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
* Units meet most national emergency escape and rescue requirements.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCX��). Specify stationary, left or right venting when ordering single units. Venting is viewed from the window exterior.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
18 ClassiC series
F.s.r.o.
G.s.
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
3'-0"3'-0 1/2"31 1/4"
E13 E23 E33
E14* E24* E34*
E15* E25* E35*
E16* E26* E36*
E156* E256* E356*
E146* E246* E346*
E136* E236* E336*
6'-0"6'-0 1/2"31 1/4"
9'-0"9'-0 1/2"31 1/4"
Casements - “e” series
C l a s s i C s e r i e s C a s e m e n t s
C a s e m e n t s “ e ” s e r i e s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configurations shown for single sash are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
* Units meet most national emergency escape and rescue requirements.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCE��). Specify stationary, left or right venting when ordering single units. Venting is viewed from the window exterior.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
19www.kolbe-kolbe.com
C l a s s i C s e r i e s C a s e m e n t s
1'-8"1'-8 1/2"15 1/4"
2'-6"2'-6 1/2"25 1/4"
N12S
N126S
X12S
X126S
N114S X114S S214S
S218S
S22S
S226S
N118S X118S
2'-8"2'-8 1/2"27 1/4"
3'-0"3'-0 1/2"31 1/4"
Casements - Rectangular transoms & studio units
3'-4"3'-4 1/2"35 1/4"
N214P W214P 4614P N314P W314P
N22P W22P 4620P N32P W32P
N226P W226P 4626P N326P W326P
N218P W218P 4618P N318P W318P
4'-0"4'-0 1/2"43 1/4"
4'-6"4'-6 1/2"49 1/4"
5'-0"5'-0 1/2"55 1/4"
6'-0"6'-0 1/2"67 1/4"
E114S
E126S
E12S
E118S
1'-4"1'-4 1/2"11 1/4"
F.s.r.o.
G.s.
1'-4
"1'
-4 1
/2"
11 1
/4"
1'-8
"1'
-8 1
/2"
15 1
/4"
2'-0"2'-0 1/2"19 1/4"
S12S
S114S
S126S
2'-0
"2'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
W12S
W126S
W114S
S118S W118S
N23P W23P 4630P N33P W33P
N24P W24P 4640P N34P W34P
N246P W246P 4646P N346P W346P
N25P W25P 4650P N35P W35P
N256P W256P 4656P N356P W356P
N26P W26P 4660P N36P W36P
N236P W236P 4636P N336P W336P
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
C a s e m e n t s r e C ta n G u l a r t r a n s O m s & s t u d i O u n i t s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
The units shown are stand-alone units. Adjustments may be required when stacking over other units; adjustments will be made in the factory.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCW��P).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
�0 ClassiC series
F.s.r.o.
G.s.
French Casements
3'-0
"3'
-0 1
/2"
31 1
/8"
3'-6
"3'
-6 1
/2"
37 1
/8"
4'-0
"4'
-0 1
/2"
43 1
/8"
4'-6
"4'
-6 1
/2"
49 1
/8"
5'-0
"5'
-0 1
/2"
55 1
/8"
5'-6
"5'
-6 1
/2"
61 1
/8"
6'-0
"6'
-0 1
/2"
67 1
/8"
3'-4"3'-4 1/2"16 1/8"
N23 W23 X23
N24 W24 X24*
N25 W25 X25*
N26
N256
N246 W246 X246*
N236 W236 X236*
4'-0"4'-0 1/2"20 1/8"
5'-0"5'-0 1/2"26 1/8"
F r e n C H C a s e m e n t s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
* Units meet most national emergency escape and rescue requirements.
PRODUCT CODES:
To order units, add “FC” before the product number (Ex: FCN��).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�1www.kolbe-kolbe.com
Casements - “n” series Picture unit Combinations
F.s.r.o.
G.s.
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
N336PL N436P N436PL N536P
N346PL N446P N446PL N546P
N356PL N456P N456PL N556P
N36PL N46P N46PL N56P
N35PL N45P N45PL N55P
N34PL N44P N44PL N54P
N33PL N43P N43PL N53P
5'-0"5'-0 1/2"
15 1/4" | 35 1/4"
N336PR
N346PR
N356PR
N36PR
N35PR
N34PR
N33PR
5'-0"5'-0 1/2"
35 1/4" | 15 1/4"
6'-8"6'-8 1/2"
15 1/4" | 35 1/4"| 15 1/4"
6'-8"6'-8 1/2"
15 1/4" | 55 1/4"
8'-4"8'-4 1/2"
15 1/4" | 55 1/4"| 15 1/4"
N436PR
N446PR
N456PR
N46PR
N45PR
N44PR
N43PR
6'-8"6'-8 1/2"
55 1/4" | 15 1/4"
C l a s s i C s e r i e s C a s e m e n t s
C a s e m e n t s “ n ” s e r i e s p i C t u r e u n i t C O m b i n at i O n s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Venting is viewed from the exterior.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCN��P).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
�� ClassiC series
W336PL
W346PL
W356PL
W36PL
W35PL
W34PL
W33PL
W436P
W446P
W456P
W46P
W45P
W44P
W43P
W436PL
W446PL
W456PL
W46PL
W45PL
W44PL
W43PL
W536P
W55P
W556P
W56P
W54P
W53P
W546P
W336PR
W346PR
W356PR
W36PR
W35PR
W34PR
W33PR
W436PR
W446PR
W456PR
W46PR
W45PR
W44PR
W43PR
Casements - “W” series Picture unit Combinations
F.s.r.o.
G.s.
6'-0"6'-0 1/2"
19 1/4" | 43 1/4"
6'-0"6'-0 1/2"
43 1/4" | 19 1/4"
8'-0"8'-0 1/2"
19 1/4" | 43 1/4"| 19 1/4"
8'-0"8'-0 1/2"
19 1/4" | 67 1/4"
10'-0"10'-0 1/2"
19 1/4" | 67 1/4" | 19 1/4"
8'-0"8'-0 1/2"
67 1/4" | 19 1/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
C a s e m e n t s “ w ” s e r i e s p i C t u r e u n i t C O m b i n at i O n s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Venting is viewed from the exterior.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCW��P).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
C l a s s i C s e r i e s C a s e m e n t s
��www.kolbe-kolbe.com
U.d.r.o.
G.s.
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
UNIT PROJECTION:
6'-6 1/2"6'-6 1/8"15 1/4"
4'-11 1/4"4'-11 3/8"15 1/4"
9'-6 3/4"9'-5 9/16"
15 1/4"
10'-11 5/8"10'-10"15 1/4"
8'-1"8'-0 1/4"15 1/4"
8 9/16"5 1/16" 17 3/16" 22 3/16"12 1/16"
N33BOW N43BOW N53BOW N63BOW
N34BOW N44BOW N54BOW N64BOW N74BOW
N35BOW N45BOW N55BOW N65BOW N75BOW
N36BOW N46BOW N56BOW N66BOW N76BOW
N356BOW N456BOW N556BOW N656BOW N756BOW
N346BOW N446BOW N546BOW N646BOW N746BOW
N336BOW N436BOW N536BOW N636BOW N736BOW
N73BOW
Casements - “n” series Bow Windows
C a s e m e n t s “ n ” s e r i e s b O w w i n d O w s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used. R.O.’s for bow units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCN7�BOW).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�� ClassiC series
W33BOW W43BOW W53BOW W63BOW
W34BOW W44BOW W54BOW W64BOW W74BOW
W35BOW W45BOW W55BOW W65BOW W75BOW
W36BOW W46BOW W56BOW W66BOW W76BOW
W356BOW W456BOW W556BOW W656BOW W756BOW
W346BOW W446BOW W546BOW W646BOW W746BOW
W336BOW W436BOW W536BOW W636BOW W736BOW
W73BOW
9 15/16"5 3/4" 20 1/4" 26 1/4"14 1/8"
U.d.r.o.
G.s.
UNIT PROJECTION:
Casements - “W” series Bow Windows
7'-10 3/16"7'-9 13/16"
19 1/4"
5'-11 3/16"5'-11 1/4"
19 1/4"
11'-5 11/16"11'-4 1/2"
19 1/4"
13'-1 15/16"13'-0 5/16"
19 1/4"
9'-8 3/8"9'-7 5/8"19 1/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
C a s e m e n t s “ w ” s e r i e s b O w w i n d O w s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used.R.O.’s for bow units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KCW7�BOW).
U.D. = Unit Dimension Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
��www.kolbe-kolbe.com
C a s e m e n t s “ s ” s e r i e s 3 0 ° b ay w i n d O w s
10 3/8"
U.D.R.O.
G.S.
UNIT PROJECTION:
“S” Series 30° Bay Windows
S16-26-16S16-16-16 S16-36-16
5'-3 1/2"5'-1 13/16"
11 1/4"
6'-7 1/2"6'-5 13/16"
11 1/4"
3'-11 1/2"3'-9 13/16"
11 1/4"3'
-0"
3'-0
1/2
"31
1/4
"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
S156-256-156
S15-25-15
S146-246-146
S14-24-14
S136-236-136
S13-23-13
S156-156-156
S15-15-15
S146-146-146
S14-14-14
S136-136-136
S13-13-13
S156-356-156
S15-35-15
S146-346-146
S14-34-14
S136-336-136
S13-33-13
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms & support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “�0KC” before the product number (Ex: �0KCS1�-1�-1�).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�� ClassiC series
12 3/8"
N15-35P-15
N16-16-16 N16-26-16 N16-26P-16 N16-36-16 N16-36P-16
N156-156-156 N156-256-156 N156-256P-156 N156-356-156 N156-356P-156
N15-15-15 N15-25-15 N15-25P-15 N15-35-15
N146-146-146 N146-246-146 N146-246P-146 N146-346-146 N146-346P-146
N14-14-14 N14-24-14 N14-24P-14 N14-34-14 N14-34P-14
N136-136-136 N136-236-136 N136-236P-136 N136-336-136 N136-336P-136
N13-13-13 N13-23-13 N13-23P-13 N13-33-13 N13-33P-13
U.d.r.o.
G.s.
UNIT PROJECTION:
Casements - “n” series 30° Bay Windows
6'-6 3/8"6'-4 3/4"15 1/4"
6'-6 3/8"6'-4 3/4"
15 1/4" | 35 1/4" | 15 1/4"
4'-10 3/8"4'-8 3/4"15 1/4"
8'-2 3/8"8'-0 3/4"
15 1/4" | 55 1/4" | 15 1/4"
8'-2 3/8"8'-0 3/4"15 1/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
C a s e m e n t s “ n ” s e r i e s 3 0 ° b ay w i n d O w s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “�0KC” before the product number (Ex: �0KCN1�-��P-1�).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�7www.kolbe-kolbe.com
14 3/8"
W13-13-13 W13-23-13 W13-23P-13 W13-33-13
W14-14-14 W14-24-14 W14-24P-14 W14-34-14 W14-34P-14
W15-15-15 W15-25-15 W15-25P-15 W15-35-15 W15-35P-15
W16-16-16 W16-26-16 W16-26P-16 W16-36-16 W16-36P-16
W156-156-156 W156-256-156 W156-256P-156 W156-356-156 W156-356P-156
W146-146-146 W146-246-146 W146-246P-146 W146-346-146 W146-346P-146
W136-136-136 W136-236-136 W136-236P-136 W136-336-136 W136-336P-136
W13-33P-13
U.d.r.o.
G.s.
UNIT PROJECTION:
Casements - “W” series 30° Bay Windows
5'-9 5/16"5'-7 11/16"
19 1/4"
7'-9 5/16"7'-7 11/16"
19 1/4"
7'-9 5/16"7'-7 11/16"
19 1/4" | 43 1/4"| 19 1/4"
9'-9 5/16"9'-7 11/16"
19 1/4"
9'-9 5/16"9'-7 11/16"
19 1/4" | 67 1/4"| 19 1/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
C a s e m e n t s “ w ” s e r i e s 3 0 ° b ay w i n d O w s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “�0KC” before the product number (Ex: �0KCW1�-��P-1�).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�8 ClassiC series
C a s e m e n t s “ X ” s e r i e s 3 0 ° b ay w i n d O w s
17 3/8"
U.D.R.O.
G.S.
UNIT PROJECTION:
“X” Series 30° Bay Windows
X156-156-156
X14-14-14
X146-146-146
X15-15-15
X13-13-13
X136-136-136
X156-256-156
X14-24-14
X146-246-146
X15-25-15
X13-23-13
X136-236-136
X13-33-13
X136-336-136
X146-346-146
X14-34-14
X15-35-15
X156-356-156
X16-16-16 X16-26-16 X16-36-16
7'-1 3/4"7'-0 1/16"25 1/4"
9'-7 3/4"9'-6 1/16"
25 1/4"
12'-1 3/4"12'-0 1/16"
25 1/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “�0KC” before the product number (Ex: �0KCX1�-1�-1�).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�9www.kolbe-kolbe.com
C a s e m e n t s “ s ” s e r i e s 4 5 ° b ay w i n d O w s
14 3/8"
U.D.R.O.
G.S.
UNIT PROJECTION:
“S” Series 45° Bay Windows
S16-26-16S16-16-16 S16-36-16
4'-11 15/16"4'-8 9/16"
11 1/4"
6'-3 15/16"6'-0 9/16"
11 1/4"
3'-7 15/16"3'-4 9/16"11 1/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
S156-256-156
S15-25-15
S146-246-146
S14-24-14
S136-236-136
S13-23-13
S156-156-156
S15-15-15
S146-146-146
S14-14-14
S136-136-136
S13-13-13
S156-356-156
S15-35-15
S146-346-146
S14-34-14
S136-336-136
S13-33-13
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “��KC” before the product number (Ex: ��KCS1�-1�-1�).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�0 ClassiC series
17 3/16"
N14-14-14 N14-24-14 N14-24P-14 N14-34-14 N14-34P-14
N15-15-15 N15-25-15 N15-25P-15 N15-35-15 N15-35P-15
N16-16-16 N16-26-16 N16-26P-16 N16-36-16 N16-36P-16
N156-256-156 N156-356P-156
N146-146-146 N146-246-146 N146-246P-146 N146-346-146 N146-346P-146
N136-136-136 N136-236-136 N136-236P-136 N136-336-136 N136-336P-136
N13-13-13 N13-23-13 N13-23P-13 N13-33-13 N13-33P-13
N156-156-156 N156-256P-156 N156-356-156
U.d.r.o.
G.s.
UNIT PROJECTION:
Casements - “n” series 45° Bay Windows
4'-5 5/8"4'-2 3/16"
15 1/4"
6'-1 5/8"5'-10 3/16"
15 1/4"
6'-1 5/8"5'-10 3/16"
15 1/4" | 35 1/4"| 15 1/4"
7'-9 5/8"7'-6 3/16"
15 1/4"
7'-9 5/8"7'-6 3/16"
15 1/4" | 55 1/4"| 15 1/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
C a s e m e n t s “ n ” s e r i e s 4 5 ° b ay w i n d O w s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “��KC” before the product number (Ex: ��KCN1�-��P-1�).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�1www.kolbe-kolbe.com
20"
W13-13-13 W13-23-13 W13-23P-13 W13-33-13
W14-14-14 W14-24-14 W14-24P-14 W14-34-14 W14-34P-14
W15-15-15 W15-25-15 W15-25P-15 W15-35-15 W15-35P-15
W16-16-16 W16-26-16 W16-26P-16 W16-36-16 W16-36P-16
W156-156-156 W156-256-156 W156-256P-156 W156-356-156 W156-356P-156
W146-146-146 W146-246-146 W146-246P-146 W146-346-146 W146-346P-146
W136-136-136 W136-236-136 W136-236P-136 W136-336-136 W136-336P-136
W13-33P-13
U.d.r.o.
G.s.
UNIT PROJECTION:
Casements - “W” series 45° Bay Windows
5'-3 1/4"4'-11 7/8"
19 1/4"
7'-3 1/4"6'-11 7/8"
19 1/4"
9'-3 1/4"8'-11 7/8"
19 1/4"
9'-3 1/4"8'-11 7/8"
19 1/4" | 67 1/4"| 19 1/4"
7'-3 1/4"6'-11 7/8"
19 1/4" | 43 1/4"| 19 1/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
C a s e m e n t s “ w ” s e r i e s 4 5 ° b ay w i n d O w s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height ifan insulated platform is being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “��KC” before the product number (Ex: ��KCW1�-��P-1�).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�� ClassiC series
C a s e m e n t s “ X ” s e r i e s 4 5 ° b ay w i n d O w s
24 1/4"
U.D.R.O.
G.S.
UNIT PROJECTION:
“X” Series 45° Bay Windows
X15-15-15
X156-156-156
X14-14-14
X146-146-146
X13-13-13
X136-136-136
X15-25-15
X156-256-156
X14-24-14
X146-246-146
X13-23-13
X136-236-136
X13-33-13
X136-336-136
X14-34-14
X146-346-146
X15-35-15
X156-356-156
X16-16-16 X16-26-16 X16-36-16
6'-5 3/4"6'-2 3/8"25 1/4"
8'-11 3/4"8'-8 3/8"25 1/4"
11'-5 3/4"11'-2 3/8"
25 1/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “��KC” before the product number (Ex: ��KCX1�-1�-1�).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
��www.kolbe-kolbe.com
U.d.r.o.
G.s.
3'-0
"3'
-0 1
/2"
31 1
/4"
3'-6
"3'
-6 1
/2"
37 1
/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
4'-6
"4'
-6 1
/2"
49 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
5'-6
"5'
-6 1
/2"
61 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
4'-7 1/2"4'-0 1/2"19 1/4"
4'-7 1/2"4'-0 1/2"43 1/4"
6'-7 1/2"6'-0 1/2"19 1/4"
6'-7 1/2"6'-0 1/2"67 1/4"
S13-W23-S13 S13-W23P-S13 S13-W33-S13 S13-W33P-S13
S14-W24-S14 S14-W24P-S14 S14-W34-S14 S14-W34P-S14
S15-W25-S15 S15-W25P-S15 S15-W35-S15 S15-W35P-S15
S16-W26-S16 S16-W26P-S16 S16-W36-S16 S16-W36P-S16
S156-W256-S156 S156-W256P-S156 S156-W356-S156 S156-W356P-S156
S146-W246-S146 S146-W246P-S146 S146-W346-S146 S146-W346P-S146
S136-W236-S136 S136-W236P-S136 S136-W336-S136 S136-W336P-S136
21 1/4"UNIT PROJECTION:
Casements - 90° Bay WindowsC a s e m e n t s 9 0 ° b ay w i n d O w s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Only flanker sash vent on 90° bay windows.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations. Sizes and grille configurations for flanker sash can be found on the Casements - “S” Series chart on pg. 1�.
If the cable support system and/or insulated platforms and support brackets are not being used, other means of proper support must be used. Add 1-11/1�" to the R.O. height if an insulated platform is being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “90KC” before the product number (Ex: 90KCS1�-W��P-S1�).
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
C l a s s i C s e r i e s C a s e m e n t s
�� ClassiC series
FrenCH Casement CrOss seCtiOn drawinGs
C l a s s i C s e r i e s C a s e m e n t s
FR
AM
E W
IDT
H
D.L
.O.
1/4"
2 7/
8"
5 7/8"
4 9/16"
1 1/
16"
FR
AM
E H
EIG
HT
2 7/
8"D
.L.O
.
1 7/
16"
FR
AM
E H
EIG
HT
D.L
.O.
1/2"
2 7/
8"
5 7/8"
4 9/16"1
1/16
"
HEAD
JAMB
SILL SILL
JAMB
HEAD
FR
AM
E H
EIG
HT
1/2"
D.L
.O.
2 7/
8"
5 7/8"
4 9/16"
1 1/
16"
5 7/8"
4 9/16"
1 1/
16"
1/4"
FR
AM
E W
IDT
H
2 7/
8"D
.L.O
.
FR
AM
E H
EIG
HT
2 7/
8"D
.L.O
.
1 7/
16"
Clad Meeting Stiles
2 1/2"
4"
French CasementCasementstandard Casement CrOss seCtiOn drawinGs
➢ Drawings are not to scale.➢ Segment head and half-circle top casement drawings are similar to standard casement drawings shown➢ Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
Clad Meeting Stiles
��www.kolbe-kolbe.com
standard mullions
Clad Casement
Wood Casement
optional narrow mullion
Clad Casement
Wood Casement
WoodClad
Rectangular Transoms Stacked over Casements
5 3/
4"
5 3/4"5 3/4"
2 1/8"2 1/8"
2 1/
2"
2 1/8"
5 3/4"
2 1/8"
2 1/
2"
5 3/4"
5 3/
4"
standard mulliOns OptiOnal narrOw mulliOns
reCtanGular transOms staCKed Over Casements
Drawings are not to scale.
C l a s s i C s e r i e s C a s e m e n t s
5 3/
4"
2 1/
8"
�� ClassiC series
Casement bOw windOw CrOss seCtiOn drawinGs
Vertical Section
Horizontal Section
Drawings are not to scale.
C l a s s i C s e r i e s C a s e m e n t s
BY OTHERS
RO
UG
H O
PE
NIN
G H
EIG
HT
UN
IT D
IME
NS
ION
HE
IGH
T
K & K INSULATED PLATFORMK & K SUPPORT BRACKET
UNIT PROJECTION
K&K INSULATED PLATFORM
1 11
/16"
1/2"
1 11/16"
UNIT DIMENSION WIDTH
10°
UN
IT P
RO
JEC
TIO
N
ROUGH OPENING WIDTH
1/4"
�7www.kolbe-kolbe.com
Casement bay windOw CrOss seCtiOn drawinGs
�0° Horizontal Section
��° Horizontal Section
90° Horizontal Section
➢ Drawings are not to scale.➢ Casement bay vertical drawings are similar to casement bow vertical drawings on pg. ��.
C l a s s i C s e r i e s C a s e m e n t s
UNIT DIMENSION WIDTH
UN
IT P
RO
JEC
TIO
N
ROUGH OPENING WIDTH
30°
UNIT DIMENSION WIDTH
45°
UN
IT P
RO
JEC
TIO
N
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH
ROUGH OPENING WIDTH
UN
IT P
RO
JEC
TIO
N
1 1/
2"3
3/4"
�8 ClassiC series
awninGsawninGs
piCture units
piCture Combination units
mulleD ConFiGurations
39www.kolbe-kolbe.com
Gl a s s:➢ H°KLoE2-240*
➢ H°KLoE3-366*
➢ Patterned-,bronze-orgray-lite
➢ Temperedorlaminated
➢ Otheroptionsstandardtotheindustry
Gr i l l e s :➢ Grilles-in-the-airspace
➢ Interiorremovablewoodgrilleswith7/8"or1-1/8"barsand
fullsurrounds
➢ PDLwith5/8",7/8",1-1/8",1-3/4"or2-1/4"bars
Ot h e r Op t i O n s: ➢ Otherwoodspecies
➢ Ovoloprofileglazingbeadsandinteriorgrillebars
➢ Interiorprefinishing
➢ Interiorcasing
➢ Prepforstool
➢ Multi-pointlocks
➢ Operatorcovers,handlesandmulti-pointlocksinWhite,Beige,
Brassorcustomfinisheslistedabove
➢ ScreenframesinWhite,BeigeorBrass,withaluminumor
charcoal-coloredaluminummesh(excludingBrassframes)
➢ Woodwrappedscreens
➢ Extensionjambs(upto12"applied,over12"shippedloosefor
fieldapplication)
➢ Motorizedwindowsystem
A w n i n g O p t i O n A l F e At u r e s
NOTES:
Allmeasurementsarenominal.
*Argongasmaynotbeincludedwithunitstobeinstalledinorshippedthroughhighaltitudeareas.
h a r d wa r e
Clay-colored, folding handles are applied to awning units as standard.
StandardawningoperatorcoversandhandlesarealsoavailableinWhite,
Beige and Brass. Custom finishes include Antique Brass, Satin Nickel,
AntiqueNickel,MatteBlack,Oil-rubbedandRusticUmber.
A w n i n g s tA n d A r d F e At u r e s
➢ 1-3/4"thicksash
➢ Overalljambwidthis4-9/16"(basicboxwidthis2-7/16"onunits,
plusextensions)
➢ Constructedofpine,withpineinteriorstopsandwoodmull
casingsonmulledunits
➢ Prefinished,heavygaugeroll-formedaluminumcladding
➢ 7/8"H°KLoE2-270insulatingglass*
➢ Glazedtotheinteriorwithwoodglazingbeads
➢ Allexteriorwoodpartsarepreservative-treated
➢ Fullyweatherstrippedforatightseal
➢ InteriorscreenswithClay-coloredaluminumframesand
charcoal-coloredfiberglassmesh
➢ Clay-coloredfoldinghandlesandoperatorcovers
➢ Roto-styleoperatorswithconcealed,adjustablehinges
➢ Heavyvinylnailingfin
Vinylnailingfinappliedasstandard
foldinghandleinClay(closed)
foldinghandleinClay(open)
C l A s s i C s e r i e s A w n i n g s
�0 ClassiC series
F.s.r.o.
G.s.
2'-6"2'-6 1/2"25 1/4"
2618
1'-8
"1'
-8 1
/2"
15 1
/4"
2620
2'-0
"2'
-0 1
/2"
19 1
/4"
2626
2'-6
"2'
-6 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
2630
3'-0"3'-0 1/2"31 1/4"
3018
3020
3026
3030
3'-6"3'-6 1/2"37 1/4"
3618
3620
3626
3630
4'-0"4'-0 1/2"43 1/4"
4018
4020
4026
4030
awnings – single units
C l a s s i C s e r i e s a w n i n G s
a w n i n G s s i n G l e u n i t s
F.s.r.o.
G.s.
2'-6"2'-6 1/2"25 1/4"
2640
2650
4'-0
"4'
-0 1
/2"
43 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
2660
3'-0"3'-0 1/2"31 1/4"
3040
3050
3060
3'-6"3'-6 1/2"37 1/4"
3650
3660
3640
4'-0"4'-0 1/2"43 1/4"
4040
4050
4060
awnings – single Picture unitsa w n i n G s s i n G l e p i C t u r e u n i t s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order single units, add “KC” before the product number and number “1” after (Ex: KC�0�01).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
D i m e n s i o n C a l C u l a t i o n s
F.S. to Sash O.S.M. -1 1�/1�" -1 1�/1�"Sash O.S.M. to G.S. -� 1�/1�" -� 1�/1�"G.S. to D.L.O. -1" -1"G.S. to Screen O.S.M. +1 9/1�" +1/�"note: Clear opening dimensions can be found on pg. 101.
F.S. = Frame Size • G.S. = Glass Size • O.S.M. = Outside MeasurementD.L.O. = Daylight Opening
wiDth heiGht
�1www.kolbe-kolbe.com
F.s.r.o.
G.s.
2'-6"2'-6 1/2"25 1/4"
26181 26182 26183
261813 261823 261833
261812 261822 261832
5'-0"5'-0 1/2"25 1/4"
7'-6"7'-6 1/2"25 1/4"
1'-8
"1'
-8 1
/2"
15 1
/4"
3'-4
"3'
-4 1
/2"
15 1
/4"
5'-0
"5'
-0 1
/2"
15 1
/4"
262012 262022 262032
262013 262023 262033
26201 26202 26203
2'-0
"2'
-0 1
/2"
19 1
/4"
4'-0
"4'
-0 1
/2"
19 1
/4"
6'-0
"6'
-0 1
/2"
19 1
/4"
26261 26262 26263
262612 262622 262632
2'-6
"2'
-6 1
/2"
25 1
/4"
5'-0
"5'
-0 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
6'-0
"6'
-0 1
/2"
31 1
/4"
26301 26302 26303
263012 263022 263032
awning units & mull Configurations2'-6" widths
Bas
ic U
nit 2
618
Bas
ic U
nit 2
620
Bas
ic U
nit 2
626
Bas
ic U
nit 2
630
F.s.r.o.
G.s.
awning Picture units2'-6" widths
2'-6"2'-6 1/2"25 1/4"
5'-0"5'-0 1/2"25 1/4"
7'-6"7'-6 1/2"25 1/4"
26401 26402 26403
26501 26502 26503
4'-0
"4'
-0 1
/2"
43 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
26601 26602 26603
Bas
ic U
nit 2
640
Bas
ic U
nit 2
650
Bas
ic U
nit 2
660
F.s.r.o.
G.s.
2'-6"2'-6 1/2"25 1/4"
5'-0"5'-0 1/2"25 1/4"
7'-6"7'-6 1/2"25 1/4"
2630181 2630182 2630183
4'-8
"4'
-8 1
/2"
15 1
/4"
| 31
1/4"
5'-0
"5'
-0 1
/2"
19 1
/4"
| 31
1/4"
2630201 2630202 2630203
2640181 2640182 2640183
5'-8
"5'
-8 1
/2"
15 1
/4"
| 43
1/4"
2640201 2640202 2640203
6'-0
"6'
-0 1
/2"
19 1
/4"
| 43
1/4"
6'-8
"6'
-8 1
/2"
15 1
/4"
| 55
1/4"
2650181 2650182 2650183
Bas
ic U
nit 2
630
over
261
8awning unit Combinations2'-6" widths
Bas
ic U
nit 2
630
over
262
0B
asic
Uni
t 264
0ov
er 2
618
Bas
ic U
nit 2
640
over
262
0B
asic
Uni
t 265
0ov
er 2
618
C l a s s i C s e r i e s a w n i n G s
a w n i n G u n i t s & m u l l C O n F i G u r at i O n s
�' �" widths
a w n i n G p i C t u r e u n i t s
�' �" widths
a w n i n G u n i t C O m b i n at i O n s
�' �" widths
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configuration shown for single units are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KC���0��).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
�� ClassiC series
F.s.r.o.
G.s.
awning units & mull Configurations3'-0" widths
1'-8
"1'
-8 1
/2"
15 1
/4"
3'-4
"3'
-4 1
/2"
15 1
/4"
5'-0
"5'
-0 1
/2"
15 1
/4"
2'-0
"2'
-0 1
/2"
19 1
/4"
4'-0
"4'
-0 1
/2"
19 1
/4"
6'-0
"6'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
5'-0
"5'
-0 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
6'-0
"6'
-0 1
/2"
31 1
/4"
3'-0"3'-0 1/2"31 1/4"
6'-0"6'-0 1/2"31 1/4"
9'-0"9'-0 1/2"31 1/4"
30181 30182 30183
302012 302022 302032
301812 301822 301832
301813 301823 301833
30201 30202 30203
302013 302023 302033
30261 30262 30263
302612 302622 302632
30301 30302 30303
303012 303022 303032
Bas
ic U
nit 3
018
Bas
ic U
nit 3
020
Bas
ic U
nit 3
026
Bas
ic U
nit 3
030
F.s.r.o.
G.s.
awning Picture units3'-0" widths
3'-0"3'-0 1/2"31 1/4"
6'-0"6'-0 1/2"31 1/4"
9'-0"9'-0 1/2"31 1/4"
4'-0
"4'
-0 1
/2"
43 1
/4"
5'-0
"5'
-0 1
/2"
55 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
30401 30402 30403
30501 30502 30503
30601 30602 30603
Bas
ic U
nit 3
040
Bas
ic U
nit 3
050
Bas
ic U
nit 3
060
F.s.r.o.
G.s.
awning unit Combinations3'-0" widths
3030201 3030202 3030203
3040181 3040182 3040183
3040201 3040202 3040203
3050181 3050182 3050183
4'-8
"4'
-8 1
/2"
15 1
/4"
| 31
1/4"
5'-0
"5'
-0 1
/2"
19 1
/4"
| 31
1/4"
5'-8
"5'
-8 1
/2"
15 1
/4"
| 43
1/4"
6'-0
"6'
-0 1
/2"
19 1
/4"
| 43
1/4"
6'-8
"6'
-8 1
/2"
15 1
/4"
| 55
1/4"
3'-0"3'-0 1/2"31 1/4"
3030181 3030182 3030183
6'-0"6'-0 1/2"31 1/4"
9'-0"9'-0 1/2"31 1/4"
Bas
ic U
nit 3
030
over
301
8B
asic
Uni
t 303
0ov
er 3
020
Bas
ic U
nit 3
040
over
301
8B
asic
Uni
t 304
0ov
er 3
020
Bas
ic U
nit 3
050
over
301
8
C l a s s i C s e r i e s a w n i n G s
a w n i n G u n i t s & m u l l C O n F i G u r at i O n s
�' 0" widths
a w n i n G p i C t u r e u n i t s
�' 0" widths
a w n i n G u n i t C O m b i n at i O n s
�' 0" widths
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configuration shown for single units are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KC�0�0��).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
��www.kolbe-kolbe.com
F.s.r.o.
awning units & mull Configurations3'-6" widths
G.s.
1'-8
"1'
-8 1
/2"
15 1
/4"
3'-4
"3'
-4 1
/2"
15 1
/4"
5'-0
"5'
-0 1
/2"
15 1
/4"
2'-0
"2'
-0 1
/2"
19 1
/4"
4'-0
"4'
-0 1
/2"
19 1
/4"
6'-0
"6'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
5'-0
"5'
-0 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
6'-0
"6'
-0 1
/2"
31 1
/4"
3'-6"3'-6 1/2"37 1/4"
7'-0"7'-0 1/2"37 1/4"
10'-6"10'-6 1/2"
37 1/4"
36181 36182 36183
361812 361822 361832
361813 361823 361833
36201 36202 36203
362012 362022 362032
362013 362023 362033
36261 36262 36263
362612 362622 362632
36301 36302 36303
363012 363022 363032
Bas
ic U
nit 3
618
Bas
ic U
nit 3
620
Bas
ic U
nit 3
626
Bas
ic U
nit 3
630
C l a s s i C s e r i e s a w n i n G s
F.s.r.o.
G.s.
awning Picture units3'-6" widths
3'-6"3'-6 1/2"37 1/4"
7'-0"7'-0 1/2"37 1/4"
10'-6"10'-6 1/2"
37 1/4"
4'-2
"4'
-0 1
/2"
43 1
/4"
5'-2
"5'
-0 1
/2"
55 1
/4"
6'-2
"6'
-0 1
/2"
67 1
/4"
36402 36403
36501 36502 36503
36601 36602 36603
36401
Bas
ic U
nit 3
640
Bas
ic U
nit 3
650
Bas
ic U
nit 3
660
F.s.r.o.
G.s.
awning unit Combinations3'-6" widths
3630181 3630182 3630183
4'-8
"4'
-8 1
/2"
15 1
/4"
| 31
1/4"
5'-0
"5'
-0 1
/2"
19 1
/4"
| 31
1/4"
5'-8
"5'
-8 1
/2"
15 1
/4"
| 43
1/4"
6'-0
"6'
-0 1
/2"
19 1
/4"
| 43
1/4"
6'-8
"6'
-8 1
/2"
15 1
/4"
| 55
1/4"
3'-6"3'-6 1/2"37 1/4"
7'-0"7'-0 1/2"37 1/4"
10'-6"10'-6 1/2"
37 1/4"
3630201 3630202 3630203
3640181 3640182 3640183
3640201 3640202 3640203
3650182 36501833650181
Bas
ic U
nit 3
630
over
361
8B
asic
Uni
t 363
0ov
er 3
620
Bas
ic U
nit 3
640
over
361
8B
asic
Uni
t 364
0ov
er 3
620
Bas
ic U
nit 3
650
over
361
8
a w n i n G u n i t s & m u l l C O n F i G u r at i O n s
�' �" widths
a w n i n G p i C t u r e u n i t s
�' �" widths
a w n i n G u n i t C O m b i n at i O n s
�' �" widths
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configuration shown for single units are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KC���0��).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
�� ClassiC series
F.s.r.o.
awning units & mull Configurations4'-0" widths
G.s.
1'-8
"1'
-8 1
/2"
15 1
/4"
3'-4
"3'
-4 1
/2"
15 1
/4"
5'-0
"5'
-0 1
/2"
15 1
/4"
2'-0
"2'
-0 1
/2"
19 1
/4"
4'-0
"4'
-0 1
/2"
19 1
/4"
6'-0
"6'
-0 1
/2"
19 1
/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
5'-0
"5'
-0 1
/2"
25 1
/4"
3'-0
"3'
-0 1
/2"
31 1
/4"
6'-0
"6'
-0 1
/2"
31 1
/4"
4'-0"4'-0 1/2"43 1/4"
8'-0"8'-0 1/2"43 1/4"
12'-0"12'-0 1/2"
43 1/4"
40181 40182 40183
401812 401822 401832
401813 401823 401833
40201 40202 40203
402012 402022 402032
402013 402023 402033
40261 40262 40263
402612 402622 402632
40301 40302 40303
403012 403022 403032
Bas
ic U
nit 4
018
Bas
ic U
nit 4
020
Bas
ic U
nit 4
026
Bas
ic U
nit 4
030
C l a s s i C s e r i e s a w n i n G s
F.s.r.o.
G.s.
awning Picture units4'-0" widths
40401 40402 40403
40501 40502 40503
40601 40602 40603
4'-0"4'-0 1/2"43 1/4"
8'-0"8'-0 1/2"43 1/4"
12'-0"12'-0 1/2"
43 1/4"
Bas
ic U
nit 4
040
Bas
ic U
nit 4
050
Bas
ic U
nit 4
060
4-0"
4'-0
1/2
"43
1/4
"
5'-0
"5'
-0 1
/2"
55 1
/4"
6'-0
"6'
-0 1
/2"
67 1
/4"
F.s.r.o.
G.s.
awning unit Combinations4'-0" widths
4030181 4030182 4030183
4030201 4030202 4030203
4040181 4040182 4040183
4040201 4040202 4040203
4050182 40501834050181
4'-8
"4'
-8 1
/2"
15 1
/4"
| 31
1/4"
5'-0
"5'
-0 1
/2"
19 1
/4"
| 31
1/4"
5'-8
"5'
-8 1
/2"
15 1
/4"
| 43
1/4"
6'-0
"6'
-0 1
/2"
19 1
/4"
| 43
1/4"
6'-8
"6'
-8 1
/2"
15 1
/4"
| 55
1/4"
4'-0"4'-0 1/2"43 1/4"
8'-0"8'-0 1/2"43 1/4"
12'-0"12'-0 1/2"
43 1/4"
Bas
ic U
nit 4
030
over
401
8B
asic
Uni
t 403
0ov
er 4
020
Bas
ic U
nit 4
040
over
401
8B
asic
Uni
t 404
0ov
er 4
020
Bas
ic U
nit 4
050
over
401
8
a w n i n G u n i t s & m u l l C O n F i G u r at i O n s
�' 0" widths
a w n i n G p i C t u r e u n i t s
�' 0" widths
a w n i n G u n i t C O m b i n at i O n s
�' 0" widths
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configuration shown for single units are typical for each sash of mulled units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KC�0�0��).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per sash.)
��www.kolbe-kolbe.com
C l a s s i C s e r i e s a w n i n G s
standard awninG CrOss seCtiOn drawinGs
standard mulliOns OptiOnal narrOw mulliOnspiCture units staCKed
Over awninGs
Drawings are not to scale.Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
FR
AM
E W
IDT
H
D.L
.O.
1/4"
2 7/
8"5 7/8"
4 9/16"
1 1/
16"
FR
AM
E H
EIG
HT
2 7/
8"D
.L.O
.
1 7/
16"
FR
AM
E H
EIG
HT
D.L
.O.
1/2"
2 7/
8"
5 7/8"
4 9/16"
1 1/
16"
HEAD
JAMB
SILL SILL
JAMB
HEAD
FR
AM
E H
EIG
HT
1/2"
D.L
.O.
2 7/
8"
5 7/8"
4 9/16"
1 1/
16"
5 7/8"
4 9/16"
1 1/
16"
1/4"
FR
AM
E W
IDT
H
2 7/
8"D
.L.O
.
FR
AM
E H
EIG
HT
2 7/
8"D
.L.O
.
1 7/
16"
Clad Meeting Stiles
2 1/2"
4"
French CasementCasement
standard mullions
Clad Casement
Wood Casement
optional narrow mullion
Clad Casement
Wood Casement
WoodClad
Rectangular Transoms Stacked over Casements
5 3/
4"
5 3/4"5 3/4"
2 1/8"2 1/8"
2 1/
2"
2 1/8"
5 3/4"
2 1/8"
2 1/
2"
5 3/4"
5 3/
4"
5 3/
4"
2 1/
8"
�� ClassiC series
Double hunGstraDitional Double hunGs
stuDio & transom units
piCture Combination units
bay units
replaCement sash Kits
�7www.kolbe-kolbe.com
C l a s s i C s e r i e s t r a d i t i O n a l d O u b l e H u n G s
t r a d i t i O n a l d O u b l e H u n G s ta n d a r d F e at u r e s
Vinyl nailing fin applied as standard
➢ 1-�/8" thick sash
➢ Overall jamb width is �-9/1�" (basic box width is �-9/1�")
➢ Frame thickness is �/�" at side jambs and head
➢ Sill thickness is 1-�/1�", slope is 1�°
➢ Constructed of pine, with pine interior stops and wood mull casings
on mulled units
➢ Prefinished, heavy gauge roll-formed aluminum cladding
➢ 9/1�" H°K LoE� insulating glass filled with argon gas*
➢ Glazed to the interior with wood glazing beads
➢ All exterior wood parts are preservative-treated
➢ Fully weatherstripped for a tight seal
➢ Clay-colored heavy duty sash lock
➢ Machined finger grooves on the top rail of the upper sash and bottom
rail of the lower sash
➢ Spring-loaded block-and-tackle mechanical balances to carry the
sash weight
➢ Beige PVC jambliners with compression foam backing
➢ Pine-veneered head and seat boards; unique narrow mullions and cable
support system on bay units
➢ Heavy vinyl nailing fin
t r a d i t i O n a l d O u b l e H u n G O p t i O n a l F e at u r e s
h a r D wa r e
Clay-colored cam locks are factory-applied to double hung units as standard.
Standard double hung hardware is also available in White, Beige and Brass.
Custom finishes for double hung sash locks include Antique Brass, Satin
Nickel, Antique Nickel, Matte Black, Oil-rubbed and Rustic Umber.
NOTES:
All measurements are nominal.
* Argon gas may not be included with units to be installed in or shipped through high altitude areas.
** Fiberglass mesh screen cloth in a charcoal color will be used unless aluminum mesh is requested.
Aluminum mesh is available in either an aluminum or charcoal color.
Gl a s s:➢ H°K LoE� -��0*
➢ H°K LoE� -���*➢ Patterned-, bronze- or gray-lite➢ Tempered or laminated➢ Other options standard to the industry
Gr i l l e s :➢ Grilles-in-the-airspace➢ Interior removable wood grilles with 7/8" or 1-1/8" bars and full surrounds➢ PDL with �/8", 7/8", 1-1/8", 1-�/�" or �-1/�" bars
ot h e r op t i o n s: ➢ Other wood species
➢ Ovolo profile glazing beads and interior grille bars➢ Interior prefinishing➢ Interior casing➢ Prep for stool➢ Sash locks in White, Beige, Brass and custom finishes listed above➢ White jambliners➢ Full screens with aluminum frames in exterior clad colors and fiberglass mesh **➢ StormGuard combination storm/screen units➢ Extension jambs (up to 1�" applied, over 1�" shipped loose for field application)➢ Insulated platforms, support brackets, and oak-veneered head and seat boards for bay units➢ Available as replacement sash kits
clay (standard) white beige
�8 ClassiC series
C l a s s i C s e r i e s d O u b l e H u n G s
DH1614 DH2014 DH2414 DH2814 DH3214DH2614 DH3014 DH3614 DH4014
DH1616 DH2016 DH2416 DH2616 DH2816 DH3016 DH3216 DH3616
DH1620 DH2020 DH2420 DH2820 DH3220DH2620 DH3020 DH3620 DH4020
DH1622 DH2022 DH2422 DH2622 DH2822 DH3022 DH3222 DH3622
DH4016
DH4022
DH1624 DH2024 DH2424 DH2824 DH3224DH2624 DH3024 DH3624 DH4024
DH1626 DH2026 DH2426 DH2626 DH2826 DH3026* DH3226* DH3626* DH4026*
DH1628 DH2028 DH2428 DH2628 DH2828* DH3028* DH3228* DH3628*
DH1630 DH2030 DH2430 DH2830* DH3230*DH2630* DH3030* DH3630* DH4030*
DH1632 DH2032 DH2432* DH2632* DH2832* DH3032* DH3232* DH3632*
DH4028*
DH4032*
DH1634 DH2034 DH2434* DH2834* DH3234*DH2634* DH3034* DH3634* DH4034*
DH1636 DH2036 DH2436* DH2636* DH2836* DH3036* DH3236* DH3636* DH4036*
1'-9 1/2"1'-10"1'-8"16"
2'-1 1/2"2'-2"2'-0"20"
3'-1 1/2"3'-2"3'-0"32"
3'-0
7/1
6"3'
-1"
2'-1
0"14
" | 1
4"
3'-4
7/1
6"3'
-5"
3'-2
"16
" | 1
6"
4'-0
7/1
6"4'
-1"
3'-1
0"20
" | 2
0"
4'-4
7/1
6"4'
-5"
4'-2
"22
" | 2
2"
4'-8
7/1
6"4'
-9"
4'-6
"24
" | 2
4"
5'-0
7/1
6"5'
-1"
4'-1
0"26
" | 2
6"
5'-4
7/1
6"5'
-5"
5'-2
"28
" | 2
8"
2'-5 1/2"2'-6"2'-4"24"
2'-9 1/2"2'-10"2'-8"28"
3'-5 1/2"3'-6"3'-4"36"
3'-9 1/2"3'-10"3'-8"40"
5'-8
7/1
6"5'
-9"
5'-6
"30
" | 3
0"
6'-0
7/1
6"6'
-1"
5'-1
0"32
" | 3
2"
6'-4
7/1
6"6'
-5"
6'-2
"34
" | 3
4"
6'-8
7/1
6"6'
-9"
6'-6
"36
" | 3
6"
F.s.r.o.
s.o.G.s.
2'-7 1/2"2'-8"2'-6"26"
2'-11 1/2"3'-0"2'-10"
30"
double Hung Units
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Single units shown are also available as singlehung units and replacement sash kits.
Grilles are optional. Follow chart down from toprow and across from left column to determine grille configurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
The side jambs of double hung units extend above the head jamb; additional space for the rough opening height may be necessary.
For rough opening recommendations, see pg. 101.
* Units meet most national emergency escape and rescue requirements.
PRODUCT CODES:
To order units, add “C” before the product number and “-1,” “-�,” or “-�” after to denote a single, twin or triple unit, respectively
(Ex: CDH�0��-1).
F.S. = Frame Size
R.O. = Rough Opening
S.O. = Sash Opening
G.S. = Glass Size
d O u b l e H u n G s s i n G l e u n i t s
�9www.kolbe-kolbe.com
5'-8
7/1
6"5'
-9"
5'-6
"36
" | 2
4"
DH1624/36 DH2024/36 DH2424/36 DH2624/36 DH2824/36 DH3024/36 DH3224/36
1'-9 1/2"1'-10"1'-8"16"
2'-1 1/2"2'-2"2'-0"20"
3'-1 1/2"3'-2"3'-0"32"
2'-5 1/2"2'-6"2'-4"24"
2'-9 1/2"2'-10"2'-8"28"
3'-5 1/2"3'-6"3'-4"36"
3'-9 1/2"3'-10"3'-8"40"
F.s.r.o.
s.o.G.s.
Cottage-style Double Hung units
DH3624/36 DH4024/36
2'-7 1/2"2'-8"2'-6"26"
2'-11 1/2"3'-0"2'-10"
30"
C l a s s i C s e r i e s d O u b l e H u n G s
Width Dimensions for Twin Mulled Units:
Glass (per-sash)
R.O.F.S
16"3'-7 1/2"
3'-7"
20"4'-3 1/2"
4'-3"
24"4'-11 1/2"
4'-11"
28"5'-7 1/2"
5'-7"
32"6'-3 1/2"
6'-3"
36"6'-11 1/2"
6'-11"
40"7'-7 1/2"
7'-7"
Width Dimensions for Triple Mulled Units:
Glass (per-sash)
R.O.F.S.
16"5'-5"
5'-4 1/2"
20"6'-5"
6'-4 1/2"
24"7'-5"
7'-4 1/2"
28"8'-5"
8'-4 1/2"
32"9'-5"
9'-4 1/2"
36"10'-5"
10'-4 1/2"
40"11'-5"
11'-4 1/2"
(DH1614-2)
(DH1614-3)
26"5'-3 1/2"
5'-3"
30"5'-11 1/2"
5'-11"
26"7'-11"
7'-10 1/2"
30"8'-11"
8'-10 1/2"
Width Dimensions for Twin Mulled Units:
Glass (per-sash)
R.O.F.S
16"3'-7 1/2"
3'-7"
20"4'-3 1/2"
4'-3"
24"4'-11 1/2"
4'-11"
28"5'-7 1/2"
5'-7"
32"6'-3 1/2"
6'-3"
36"6'-11 1/2"
6'-11"
40"7'-7 1/2"
7'-7"
Width Dimensions for Triple Mulled Units:
Glass (per-sash)
R.O.F.S.
16"5'-5"
5'-4 1/2"
20"6'-5"
6'-4 1/2"
24"7'-5"
7'-4 1/2"
28"8'-5"
8'-4 1/2"
32"9'-5"
9'-4 1/2"
36"10'-5"
10'-4 1/2"
40"11'-5"
11'-4 1/2"
(DH1614-2)
(DH1614-3)
26"5'-3 1/2"
5'-3"
30"5'-11 1/2"
5'-11"
26"7'-11"
7'-10 1/2"
30"8'-11"
8'-10 1/2"
w i d t H d i m e n s i O n s F O r t w i n m u l l e d u n i t s
w i d t H d i m e n s i O n s F O r t r i p l e m u l l e d u n i t s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
The side jambs of double hung units extend above the head jamb; additional space for the rough opening height may be necessary.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “C” before the product number and “-1,” “-�,” or “-�” after to denote a single, twin or triple unit, respectively (Ex: CDH1���/��-1).
F.S. = Frame Size • R.O. = Rough Opening
S.O. = Sash Opening • G.S. = Glass Size
D i m e n s i o n C a l C u l a t i o n s
F.S. to S.O. -1 1/�" -� 7/1�"S.O. to G.S. -�" -�"÷�G.S. to D.L.O. -1" -1"note: Clear opening dimensions can be found on pg. 101. Cottage-style dimension calculations are different; please contact your supplier.
F.S. = Frame Size • G.S. = Glass Size • S.O. = Sash OpeningD.L.O. = Daylight Opening
d O u b l e H u n G s C O t ta G e - s t y l e u n i t s
wiDth heiGht
�0 ClassiC series
1'-9 1/2"1'-10"1'-8"16"
2'-1 1/2"2'-2"2'-0"20"
3'-1 1/2"3'-2"3'-0"32"
0'-1
1 1/
2"1'
-0"
10"
6"
1'-3
1/2
"1'
-4"
14"
10"
1'-5
1/2
"1'
-6"
16"
12"
1'-7
1/2
"1'
-8"
18"
14"
1'-1
1 1/
2"2'
-0"
22"
18"
2'-5
1/2
"2'
-6"
28"
24"
2'-5 1/2"2'-6"2'-4"24"
2'-9 1/2"2'-10"2'-8"28"
3'-5 1/2"3'-6"3'-4"36"
3'-9 1/2"3'-10"3'-8"40"
F.s.r.o.
s.o.G.s.
Double Hungs – Rectangular transoms
DHT1606 DHT2006 DHT2406 DHT2806 DHT3206 DHT3606 DHT4006
DHT1614 DHT2014 DHT2414 DHT2814 DHT3214 DHT3614 DHT4014
DHT1618 DHT2018 DHT2418 DHT2818 DHT3218 DHT3618 DHT4018
DHT1624 DHT2024 DHT2424 DHT2824 DHT3224 DHT3624 DHT4024
DHT1610 DHT2010 DHT2410 DHT2810 DHT3210 DHT3610 DHT4010
DHT1612 DHT2012 DHT2412 DHT2812 DHT3212 DHT3612 DHT4012
C l a s s i C s e r i e s d O u b l e H u n G s
d O u b l e H u n G s r e C ta n G u l a r t r a n s O m s
NOTES:
All measurements are nominal. These dimensions apply only for transoms with flat sills. Contact your supplier for dimensions ofunits with beveled sills. Elevation charts are not to scale.
Transom units are only available with a 1-�/�" sash.
The units shown are stand-alone units. Adjustments may be required when stacking over other units; adjustments will be made in the factory.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
The side jambs of double hung units extend above the head jamb; additional space for the rough opening height may be necessary.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order transoms, add “C” before the product number (Ex: CDHT�0��).
F.S. = Frame Size • R.O. = Rough Opening • S.O. = Sash Opening • G.S. = Glass Size
�1www.kolbe-kolbe.com
F.s.r.o.
s.o.G.s.
4'-1 1/2"4'-2"4'-0"
44 1/2"
DHS40310 DHS44310 DHS50310
DHS4042 DHS4442 DHS5042
4'-5 1/2"4'-6"4'-4"
48 1/2"
5'-1 1/2"5'-2"5'-0"
56 1/2"
4'-0
7/1
6"4'
-1"
3'-1
0"41
1/4
"
4'-4
7/1
6"4'
-5"
4'-2
"45
1/4
"
4'-8
7/1
6"4'
-9"
4'-6
"49
1/4
"
5'-0
7/1
6"5'
-1"
4'-1
0"53
1/4
"
DHS4046 DHS4446 DHS5046
DHS40410 DHS44410 DHS50410
DHS58310 DHS64310 DHS70310
DHS5842 DHS6442
DHS84310
DHS7042 DHS8442
DHS5846 DHS6446 DHS7046
DHS70410
DHS8446
DHS5052
DHS84410DHS58410 DHS64410
DHS5852 DHS6452 DHS7052 DHS8452
DHS4056 DHS4456 DHS5056 DHS5856 DHS6456 DHS7056 DHS8456
DHS4452DHS4052
5'-4
7/1
6"5'
-5"
5'-2
"57
1/4
"
5'-8
7/1
6"5'
-9"
5'-6
"*61
1/4
"
5'-9 1/2"5'-10"5'-8"
64 1/2"
6'-5 1/2"6'-6"6'-4"
72 1/2"
7'-1 1/2"7'-2"7'-0"
80 1/2"
8'-5 1/2"8'-6"8'-4"
96 1/2"
6'-0
7/1
6"6'
-1"
5'-1
0"65
1/4
"
6'-4
7/1
6"6'
-5"
6'-2
"69
1/4
"
6'-8
7/1
6"6'
-9"
6'-6
"73
1/4
"
DHS40510 DHS44510 DHS50510 DHS58510 DHS64510 DHS70510 DHS84510
DHS4062 DHS4462 DHS5062 DHS5862 DHS6462 DHS7062 DHS8462
DHS4066 DHS4466 DHS5066 DHS5866 DHS6466 DHS7066 DHS8466
Double Hungs – studio Picture units
C l a s s i C s e r i e s d O u b l e H u n G s
d O u b l e H u n G s s t u d i O u n i t s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Studio units are only available with a 1-�/�" sash.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
The side jambs of double hung units extend above the head jamb; additional space for the rough opening height may be necessary.
For rough opening recommendations, see pg. 101.
* To match cottage-style double hungs with grilles, �'-�" high (S.O.) units must be ordered � lites high.
PRODUCT CODES:
To order units, add “C” before the product number (Ex: CDHS8���).
F.S. = Frame Size • R.O. = Rough Opening • S.O. = Sash Opening • G.S. = Glass Size
�� ClassiC series
F.s.r.o.
s.o.G.s.*
Double Hung Picture units16" flankers
8'-0 1/2"8'-1"
1'-8" | 4'-4" | 1'-8"16" | 48 1/2" | 16"
10'-0 1/2"10'-1"
1'-8" | 6'-4" | 1'-8"16" | 72 1/2" | 16"
4'-4
7/1
6"4'
-5"
4'-2
"22
" | 4
5 1/
4"
4'-8
7/1
6"4'
-9"
4'-6
"24
" | 4
9 1/
4"
5'-5
7/1
6"5'
-5"
5'-2
"28
" | 5
7 1/
4"
8'-8 1/2"8'-9"
1'-8" | 5'-0" | 1'-8"16" | 56 1/2" | 16"
9'-4 1/2"9'-5"
1'-8" | 5'-8" | 1'-8"16" | 64 1/2" | 16"
DH16284452 DH16285052 DH16285852 DH16286452
DH16224442 DH16225042 DH16225842 DH16226442
DH16244446 DH16245046 DH16245846 DH16246446
C l a s s i C s e r i e s d O u b l e H u n G s
d O u b l e H u n G p i C t u r e u n i t s
1�" flankers
d O u b l e H u n G p i C t u r e u n i t s
�0" flankers
F.s.r.o.
s.o.G.s.*
4'-4
7/1
6"4'
-5"
4'-2
"22
" | 4
5 1/
4"
4'-8
7/1
6"4'
-9"
4'-6
"24
" | 4
9 1/
4"
5'-5
7/1
6"5'
-5"
5'-2
"28
" | 5
7 1/
4"
8'-8 1/2"8'-9"
2'-0" | 4'-4" | 2'-0"20" | 48 1/2" | 20"
10'-8 1/2"10'-9"
2'-0" | 6'-4" | 2'-0"20" | 72 1/2" | 20"
9'-4 1/2"9'-5"
2'-0" | 5'-0" | 2'-0"20" | 56 1/2" | 20"
10'-0 1/2"10'-1"
2'-0" | 5'-8" | 2'-0"20" | 64 1/2" | 20"
DH20284452 DH20285052 DH20285852 DH20286452
DH20224442 DH20225042 DH20225842 DH20226442
DH20244446 DH20245046 DH20245846 DH20246446
Double Hung Picture units20" flankers
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Center picture units are only available with a 1-�/�" sash.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
The side jambs of double hung units extend above the head jamb; additional space for the rough opening height may be necessary.For rough opening recommendations, see pg. 101.
* The first number of the glass size height is the height (per sash) for each flanker sash. The second number is the glass height forthe center picture unit.
PRODUCT CODES:
To order units, add “C” before the product number (Ex: CDH�0�8����).
F.S. = Frame Size • R.O. = Rough Opening • S.O. = Sash Opening • G.S. = Glass Size
��www.kolbe-kolbe.com
C l a s s i C s e r i e s d O u b l e H u n G s
d O u b l e H u n G p i C t u r e u n i t s
��" flankers
F.s.r.o.
s.o.G.s.*
DH24284452 DH24285052 DH24285852 DH24286452
DH24224442 DH24225042 DH24225842 DH24226442
DH24244446 DH24245046 DH24245846 DH24246446
4'-4
7/1
6"4'
-5"
4'-2
"22
" | 4
5 1/
4"
4'-8
7/1
6"4'
-9"
4'-6
"24
" | 4
9 1/
4"
5'-5
7/1
6"5'
-5"
5'-2
"28
" | 5
7 1/
4"9'-4 1/2"
9'-5"2'-4" | 4'-4" | 2'-4"24" | 48 1/2" | 24"
11'-4 1/2"11'-5"
2'-4" | 6'-4" | 2'-4"24" | 72 1/2" | 24"
10'-0 1/2"10'-1"
2'-4" | 5'-0" | 2'-4"24" | 56 1/2" | 24"
10'-8 1/2"10'-9"
2'-4" | 5'-8" | 2'-4"24" | 64 1/2" | 24"
Double Hung Picture units24" flankers
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Center picture units are only available with a 1-�/�" sash.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
The side jambs of double hung units extend above the head jamb; additional space for the rough opening height may be necessary.
* The first number of the glass size height is the height (per sash) for each flanker sash. The second number is the glass height for the center picture unit.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “C” before the product number (Ex: CDH���8����).
F.S. = Frame Size • R.O. = Rough Opening • S.O. = Sash Opening • G.S. = Glass Size
�� ClassiC series
U.d.r.o.
s.o.G.s.*
20" flankers
8'-0 9/16"7'-11"
1'-8" | 4'-4" | 1'-8"16" | 48 1/2" | 16"
8'-8 9/16"8'-7"
1'-8" | 5'-0" | 1'-8"16" | 56 1/2" | 16"
4'-5
3/1
6"4'
-5 1
1/16
"4'
-2"
22"
| 45
1/4"
4'-9
3/1
6"4'
-9 1
1/16
"4'
-6"
24"
| 49
1/4"
DH30-16224442 DH30-16225042
DH30-16244446 DH30-16245046
8'-7 9/16"8'-5 15/16"
2'-0" | 4'-4" | 2'-0"20" | 48 1/2" | 20"
9'-3 9/16"9'-1 5/16"
2'-0" | 5'-0" | 2'-0"20" | 56 1/2" | 20"
5'-5
3/1
6"5'
-5 1
1/16
"5'
-2"
28"
| 57
1/4"
DH30-20224442 DH30-20225042
DH30-20244446 DH30-20245046
DH30-20285052
UNIT PROJECTION: UNIT PROJECTION:13 7/16" 15 3/8"
Double Hungs – 30° Bay Windows16" flankers
C l a s s i C s e r i e s d O u b l e H u n G s
d O u b l e H u n G s 3 0 ° b ay w i n d O w s
1�" flankers �0" flankers
20" flankersDouble Hungs – 45° Bay Windows16" flankers
U.d.r.o.
s.o.G.s.*
4'-5
3/1
6"4'
-5 1
1/16
"4'
-2"
22"
| 45
1/4"
4'-9
3/1
6"4'
-9 1
1/16
"4'
-6"
24"
| 49
1/4"
5'-5
3/1
6"5'
-5 1
1/16
"5'
-2"
28"
| 57
1/4"
7'-8 1/4"7'-4 7/8"
1'-8" | 4'-4" | 1'-8"16" | 48 1/2" | 16"
8'-4 1/4"8'-0 7/8"
1'-8" | 5'-0" | 1'-8"16" | 56 1/2" | 16"
DH45-16224442 DH45-16225042
DH45-16244446 DH45-16245046
8'-1 15/16"7'-10 1/2"
2'-0" | 4'-4" | 2'-0"20" | 48 1/2" | 20"
8'-9 15/16"8'-6 1/2"
2'-0" | 5'-0" | 2'-0"20" | 56 1/2" | 20"
DH45-20224442 DH45-20225042
DH45-20244446 DH45-20245046
DH45-20285052
UNIT PROJECTION: UNIT PROJECTION: 18 7/8" 21 3/4"
d O u b l e H u n G s 4 5 ° b ay w i n d O w s
1�" flankers �0" flankers NOTES:
All measurements are nominal. Elevation charts are not to scale.
Center picture units are only available with a 1-�/�" sash.
Grilles are optional. Follow chart down from top row and across from left column to determine grille configurations.
If the cable support system and/or insulated platforms & supportbrackets are not being used, other means of proper support mustbe used. Add 1-1�/1�" to the R.O. height if an insulated platformis being used. R.O.’s for bay units without head and seat boards, typically used for walk-out applications, are different.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
The side jambs of double hung units extend above the head jamb; additional space for the rough opening height may be necessary.
For rough opening recommendations, see pg. 101.
* The first number of the glass size height is the height (per sash) for each flanker sash. The second number is the glassheight for the center picture unit.
PRODUCT CODES:
To order units, add “C” before the product number
(Ex: CDH��-�0�8�0��).
U.D. = Unit Dimension
R.O. = Rough Opening
S.O. = Sash Opening
G.S. = Glass Size
��www.kolbe-kolbe.com
C l a s s i C s e r i e s d O u b l e H u n G s
UNIT DIMENSION WIDTH & FRAME WIDTH
3 1/4"
1/4"
ROUGH OPENING WIDTH
3 1/4" D.L.O.
1/4"
JamBs
Traditional Double Hung Cross Section Drawings
Clad Vertical Section
siLL
Head
4 9/16"
3 3/
16"
RO
UG
H O
PE
NIN
G H
EIG
HT
FR
AM
E &
UN
IT D
IME
NS
ION
HE
IGH
T
2 1/
4"D
.L.O
.
1 5/16"
D.L
.O.
5"
9/16"
3 11/64"
1 7/8"
5 7/8"
1 5/16"
traditiOnal dOuble HunG CrOss seCtiOn drawinGs
Vertical Section
Horizontal Section
UNIT DIMENSION WIDTH & FRAME WIDTH
3 1/4"
1/4"
ROUGH OPENING WIDTH
3 1/4" D.L.O.
1/4"
JamBs
Traditional Double Hung Cross Section Drawings
Clad Vertical Section
siLL
Head
4 9/16"
3 3/
16"
RO
UG
H O
PE
NIN
G H
EIG
HT
FR
AM
E &
UN
IT D
IME
NS
ION
HE
IGH
T
2 1/
4"D
.L.O
.
1 5/16"
D.L
.O.
5"
9/16"
3 11/64"
1 7/8"
5 7/8"
1 5/16"
Drawings are not to scale.Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
�� ClassiC series
Double Hung Studio Unit Cross Section Drawings
Traditional Clad
Standard Narrow Mullions
Clad Double Hung
Rectangular Transoms Stacked over Double Hungs
Clad
6 7/
16"
2 5/
8"
SUPPLIED BY OTHERS
6 1/2"
FR
AM
E W
TH
.F
RA
ME
HT.
Head
FR
AM
E H
T.
JamB
siLL
1 5/16"
5"D
.O.
3 15/32"
D.O
.
1 7/32"
D.O
.3
15/6
4"
5 7/8"
4 9/16"
1 7/32"
3"
5 7/8"
4 9/16"
dOuble HunG studiO unit CrOss seCtiOn drawinGs
Standard Narrow Mullions
Rectangular Transoms Stacked over Traditional Double Hungs
C l a s s i C s e r i e s d O u b l e H u n G s
Drawings are not to scale.
Double Hung Studio Unit Cross Section Drawings
Traditional WoodTraditional Clad
Standard Narrow Mullions Optional Support Mullions
8 1/2"
2" SUPPLIED BY OTHERS
Clad Double Hung Clad Double Hung
SUPPLIED BY OTHERS
Wood Double Hung Wood Double Hung
Rectangular Transoms Stacked over Double Hungs Double Hung Transoms with Optional Beveled Sills
Clad Wood Clad Wood6
7/16
"
2 5/
8"
6 7/
16"
2 5/
8"
6 1/2"
SUPPLIED BY OTHERS
6 1/2"8 1/2"
2" SUPPLIED BY OTHERS
Sterling Wood
siLL
1/4"
JamB
D.O
.4
61/6
4"F
RA
ME
HT
.D
.O.
3 1/8"
FR
AM
E W
TH
.3"
FR
AM
E H
T.
D.O
.3
7/32
"9/
16"
4 9/16"
5 5/8"
1 9/16"
1 9/16"
4 9/16"
5 5/8"Head
FR
AM
E W
TH
.F
RA
ME
HT
.
Head
FR
AM
E H
T.
JamB
siLL
1 5/16"
5"D
.O.
3 15/32"
D.O
.
1 7/32"
D.O
.3
15/6
4"
5 7/8"
4 9/16"
1 7/32"
3"
5 7/8"
4 9/16"
Head
JamB
siLL
FR
AM
E W
TH
.F
RA
ME
HT
.4
15/1
6"D
.O.
3 27/64"
D.O
.3"
FR
AM
E H
T.
3 15
/64"
D.O
.
5 5/8"4 9/16"
4 9/16"
1 7/32"
1 7/32"
5 5/8"
Double Hung Studio Unit Cross Section Drawings
Traditional WoodTraditional Clad
Standard Narrow Mullions Optional Support Mullions
8 1/2"
2" SUPPLIED BY OTHERS
Clad Double Hung Clad Double Hung
SUPPLIED BY OTHERS
Wood Double Hung Wood Double Hung
Rectangular Transoms Stacked over Double Hungs Double Hung Transoms with Optional Beveled Sills
Clad Wood Clad Wood
6 7/
16"
2 5/
8"
6 7/
16"
2 5/
8"
6 1/2"
SUPPLIED BY OTHERS
6 1/2"8 1/2"
2" SUPPLIED BY OTHERS
Sterling Wood
siLL
1/4"
JamB
D.O
.4
61/6
4"F
RA
ME
HT
.D
.O.
3 1/8"
FR
AM
E W
TH
.3"
FR
AM
E H
T.
D.O
.3
7/32
"9/
16"
4 9/16"
5 5/8"
1 9/16"
1 9/16"
4 9/16"
5 5/8"Head
FR
AM
E W
TH
.F
RA
ME
HT
.
Head
FR
AM
E H
T.
JamB
siLL
1 5/16"
5"D
.O.
3 15/32"
D.O
.
1 7/32"
D.O
.3
15/6
4"
5 7/8"
4 9/16"
1 7/32"
3"
5 7/8"
4 9/16"
Head
JamB
siLL
FR
AM
E W
TH
.F
RA
ME
HT
.4
15/1
6"D
.O.
3 27/64"
D.O
.3"
FR
AM
E H
T.
3 15
/64"
D.O
.
5 5/8"4 9/16"
4 9/16"
1 7/32"
1 7/32"
5 5/8"
Traditional
�7www.kolbe-kolbe.com
C l a s s i C s e r i e s d O u b l e H u n G s
Drawings are not to scale.
UNIT DIMENSION WIDTH
UNIT DIMENSION WIDTH
JamBs
UN
IT P
RO
JEC
TIO
N
30˚
ROUGH OPENING WIDTH
Wood
CladJamBs
Double Hung �0 & �� Bay Vertical Cross Section Drawings
Clad Wood
Double Hung �0 Bay Horizontal Cross Section DrawingsU
NIT
PR
OJE
CT
ION
ROUGH OPENING WIDTH
30˚
Head
UNIT PROJ.
K & K INSULATED PLATFORM
K & K INSULATED PLATFORM
1 11/16"
K & K SUPPORT BRACKET
siLL
BY OTHERS
RO
UG
H O
PE
NIN
G H
T.
FR
AM
E &
UN
IT D
IME
NS
ION
HT
.
1 9/16"9/16"
Head
BY OTHERS
K & K INSULATED PLATFORM
UNIT PROJ.
K & K SUPPORT BRACKET
K & K INSULATED PLATFORM
siLL
EXTERIOR TRIM CAP, TO BE SUPPLIED BY OTHERS FOR (NON) KOLBE
INSULATING PLATFORM.
3 15
/16"
1/2"
4 31
/32
FR
AM
E H
EIG
HT
UN
IT D
IME
NS
ION
HE
IGH
T
RO
UG
H O
PE
NIN
G
D.L
.O.
9/16"
dOuble HunG 30° & 45° bay vertiCal CrOss drawinGs
dOuble HunG 30° bay HOrizOntal CrOss seCtiOn drawinGs
UNIT DIMENSION WIDTH
UNIT DIMENSION WIDTH
JamBs
UN
IT P
RO
JEC
TIO
N
30˚
ROUGH OPENING WIDTH
Wood
CladJamBs
Double Hung �0 & �� Bay Vertical Cross Section Drawings
Clad Wood
Double Hung �0 Bay Horizontal Cross Section Drawings
UN
IT P
RO
JEC
TIO
N
ROUGH OPENING WIDTH
30˚
Head
UNIT PROJ.
K & K INSULATED PLATFORM
K & K INSULATED PLATFORM
1 11/16"
K & K SUPPORT BRACKET
siLL
BY OTHERS
RO
UG
H O
PE
NIN
G H
T.
FR
AM
E &
UN
IT D
IME
NS
ION
HT
.
1 9/16"9/16"
Head
BY OTHERS
K & K INSULATED PLATFORM
UNIT PROJ.
K & K SUPPORT BRACKET
K & K INSULATED PLATFORM
siLL
EXTERIOR TRIM CAP, TO BE SUPPLIED BY OTHERS FOR (NON) KOLBE
INSULATING PLATFORM.
3 15
/16"
1/2"
4 31
/32
FR
AM
E H
EIG
HT
UN
IT D
IME
NS
ION
HE
IGH
T
RO
UG
H O
PE
NIN
G
D.L
.O.
9/16"
Wood
Clad
Double Hung �� Bay Horizontal Cross Section Drawings
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH
UNIT DIMENSION WIDTH
UN
IT P
RO
JEC
TIO
N
45˚
ROUGH OPENING WIDTH
UN
IT P
RO
JEC
TIO
N
45˚
dOuble HunG 45° bay HOrizOntal CrOss seCtiOn drawinGs
�8 ClassiC series9� Kolbe winDows & Doors
Drawings are not to scale.
sliDers Double sliDers
triple sliDers
�9www.kolbe-kolbe.com
NOTES:
All measurements are nominal.
* Argon gas may not be included with units to be installed in or shipped through high altitude areas.
** Fiberglass mesh screen cloth in a charcoal color will be used unless aluminum mesh is requested.
Aluminum mesh is available in either an aluminum or charcoal color.
s l i d e r s ta n d a r d F e at u r e s
➢ 1-�/8" thick sash
➢ 9/1�" H°K LoE�-�70 insulating glass*
➢ Overall jamb width is �-9/1�" (basic box width is �-9/1�")
➢ Constructed of pine, with pine interior stops
➢ Prefinished, heavy gauge roll-formed aluminum cladding
➢ Glazed to the interior with wood glazing beads
➢ All exterior wood parts are preservative-treated
➢ Rigid PVC waterseal at the sill
➢ Fully weatherstripped for a tight seal
➢ Clay-colored heavy duty sash locks
➢ Machined finger grooves on the outermost stiles
➢ Beige extruded vinyl head and sill tracks with compression foam
backing on the head track
➢ Heavy vinyl nailing fin
Gl a s s:➢ H°K LoE� -��0*
➢ H°K LoE� -���*➢ Patterned-, bronze- or gray-lite➢ Tempered or laminated➢ Other options standard to the industry
Gr i l l e s :➢ Grilles-in-the-airspace➢ Interior removable wood grilles with 7/8" or 1-1/8" bars and full surrounds➢ PDL with �/8", 7/8", 1-1/8", 1-�/�" or �-1/�" bars
ot h e r op t i o n s: ➢ Other wood species➢ Ovolo profile glazing beads and interior grille bars➢ Interior prefinishing➢ Interior casing➢ Prep for stool➢ Sash locks in White, Beige, Brass and custom finishes listed above➢ Full screens with aluminum frames in exterior clad colors and fiberglass mesh**➢ StormGuard combination storm/screen units➢ Extension jambs (up to 1�" applied, over 1�" shipped loose for field application)
s l i d e r O p t i O n a l F e at u r e s
h a r D wa r e
Clay-colored cam locks are factory-applied to slider units as
standard. Standard slider hardware is also available in White,
Beige and Brass. Custom finishes for slider sash locks include
Antique Brass, Satin Nickel, Antique Nickel, Matte Black and
Rustic Umber.
C l a s s i C s e r i e s s l i d e r s
Vinyl nailing fin applied as standard
Clay (standard) White Beige
�0 ClassiC series
D i m e n s i o n C a l C u l a t i o n s
F.S. to S.O. -1 1/�" -1 1�/1�"R.O. to G.S. -7"÷� -7 �/8"G.S. to D.L.O. -1" -1"note: Clear opening dimensions can be found on pg. 101.
F.S. = Frame Size • G.S. = Glass Size • S.O. = Sash OpeningR.O. = Rough Opening • D.L.O. = Daylight Opening
C l a s s i C s e r i e s s l i d e r s
3'-2 1/2"3'-3"3'-1"
16" | 16"
3'-10 1/2"3'-11"3'-9"
20" | 20"
5'-10 1/2"5'-11"5'-9"
32" | 32"
4'-6 1/2"4'-7"4'-5"
24" | 24"
5'-2 1/2"5'-3"5'-1"
28" | 28"
F.s.r.o.
s.o.G.s.
Double sliders
1'-1
0 13
/16"
1'-1
1 3/
8"1'
-9"
16"
2'-2
13/
16"
2'-3
3/8
"2'
-1"
20"
2'-6
13/
16"
2'-7
3/8
"2'
-5"
24"
2'-1
0 13
/16"
2'-1
1 3/
8"2'
-9"
28"
3'-2
13/
16"
3'-3
3/8
"3'
-1"
32"
3'-6
13/
16"
3'-7
3/8
"3'
-5"
36"
3'-1
0 13
/16"
3'-1
1 3/
8"3'
-9"
40"
4'
-2 1
3/16
"4'
-3 3
/8"
4'-1
"44
"
4'-6
13/
16"
4'-7
3/8
"4'
-5"
48"
SL1616 SL2016 SL2416 SL3216SL2816
SL1620 SL2020 SL2420 SL3220SL2820
SL1624 SL2024 SL2424 SL3224*SL2824
SL1628 SL2028 SL2428 SL3228*SL2828*
SL1632 SL2032 SL2432 SL3232*SL2832*
SL1636 SL2036 SL2436* SL3236*SL2836*
SL1640 SL2040 SL2440* SL3240*SL2840*
SL1644 SL2044 SL2444* SL3244*SL2844*
SL1648 SL2048 SL2448* SL3248*SL2848*
t r a d i t i O n a l d O u b l e s l i d e r s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. Follow chart down from top row and across from left column to determine grilleconfigurations.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
The side jambs of slider units extend above the head jamb; additional space for the rough opening height may be necessary.
* Units meet most national emergency escape and rescue requirements.
PRODUCT CODES:
To order units, add “C” before the product number (Ex: CSL���8).
F.S. = Frame Size • R.O. = Rough Opening • S.O. = Sash Opening • G.S. = Glass Size
wiDth heiGht
�1www.kolbe-kolbe.com
C l a s s i C s e r i e s s l i d e r s
F.s.r.o.
s.o.G.s.
triple sliders
5'-11 1/2"6'-0"5'-10"
16" | 31 1/2" | 16"
7'-3 1/2"7'-4"7'-2"
20" | 39 1/2" | 20"
7'-11 1/2"8'-0"7'-10"
20" | 47 1/2" | 20"
8'-7 1/2"8'-8"8'-6"
24" | 47 1/2" | 24"
3'-2
13/
16"
3'-3
3/8
"3'
-1"
31 1
/2"
3'-1
0 13
/16"
3'-1
1 3/
8"3'
-9"
39 1
/2"
4'-2
13/
16"
4'-3
3/8
"4'
-1"
43 1
/2"
4'-6
13/
16"
4'-7
3/8
"4'
-5"
47 1
/2"
TSL163232 TSL204032 TSL244832*TSL204832
TSL163240 TSL204040* TSL244840*TSL204840*
TSL163244 TSL204044* TSL244844*TSL204844*
TSL163248 TSL204048* TSL244848*TSL204848*
C l a s s i C t r i p l e s l i d e r s
Traditional Double Slider Cross Section Drawings
Clad Vertical Section Clad Horizontal Section Wood Vertical Section Wood Horizontal Section
Royal Double Slider Cross Section Drawings
Wood Vertical Section Wood Horizontal Section
Royal Triple Slider Horizontal Cross Section Drawings
Clad Wood
D.L.O. 3 1/8"2 3/8"2 3/8"3 1/8" D.L.O.D.L.O.
1/4"UNIT DIMENSION WIDTH & FRAME WIDTH
ROUGH OPENING WIDTH
1/4"
JamBs
D.L.O. D.L.O. 3 1/8"2 3/8"2 3/8" D.L.O.3 1/8"
1 1/8"
1/4"1/4"
UNIT DIMENSION WIDTH
ROUGH OPENING WIDTH
FRAME WIDTH
1/4"1/4" FRAME & UNIT DIM. WIDTH
ROUGH OPENING WIDTH
3 1/8" D.L.O. 2 1/4"
JamBs
D.L.O. 3 1/8"
1 3/16"
1/4"
UNIT DIMENSION WIDTH
ROUGH OPENING WIDTH
FRAME WIDTH
JamBs
D.L.O.3 1/8" 2 1/4" 3 1/8"
1/4"
1 3/16"
1/4"
UNIT DIMENSION WIDTH
ROUGH OPENING WIDTH
FRAME WIDTH
JamBs
D.L.O.3 1/8" 2 3/8" 3 1/8"
1/4"
D.L.O.
D.L.O.
JamBs
FR
AM
E &
UN
IT D
IME
NS
ION
HT
.4
17/3
2"
SILL
D.L
.O.
3 5/
16"
Head
1 5/16"
2 59/64"1 5/8"
5 7/8"
4 9/16"
1 5/16"
Head
siLL
9/16"
3 5/
16"
4 1/
2"
UN
IT D
IME
NS
ION
HE
IGH
TR
OU
GH
OP
EN
ING
HE
IGH
TF
RA
ME
HE
IGH
T
D.L
.O.
1/2"
1 5/8"2 57/64"
4 9/16"
5 5/8"
1 5/16"
Head
siLL
2 59/64"
UN
IT D
IME
NS
ION
HE
IGH
TR
OU
GH
OP
EN
ING
HE
IGH
T
4 1/
2"
1/2"
FR
AM
E H
EIG
HT
D.L
.O.
3 5/
16"
1 5/8"
5 5/8"
4 9/16"
9/16"
1 5/16"
traditiOnal dOuble slider CrOss seCtiOn drawinGs
Vertical Section Horizontal Section
ClassiC triple slider HOrizOntal CrOss seCtiOn drawinGs
Drawings not to scale.Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
See notes on previous page for additional information.
ROUGH OPENING WIDTH
UNIT DIMENSION & FRAME WIDTH
D.L.O. D.L.O. D.L.O.3 1/8" 3 1/8"2 1/4" 2 1/4"
1/4" 1/4"
�� ClassiC series�8 Kolbe winDows & Doors
patio Doorsviewport sliDinG patio Doors
GarDen-aire sliDinG patio Doors
inswinG patio Doors
patio Door transoms
��www.kolbe-kolbe.com
v i e w p O r t s ta n d a r d F e at u r e s
➢ Standard jamb width is �-9/1�" on units
➢ 1-�/�" thick sash panels
➢ �" wide LVL stiles and rails
➢ Constructed of pine, with pine interior stops
➢ Prefinished, heavy gauge roll-formed aluminum cladding
➢ Glazed to the interior with wood glazing beads
➢ Tempered, 7/8" H°K LoE�-�70 insulating glass*
➢ All exterior wood parts are preservative-treated
➢ Fully weatherstripped for a tight seal
➢ Tandem rollers with adjustable, ball-bearing wheels carry
the sliding panel
➢ Rustic-colored handle set and mortise latch
➢ Screens with fiberglass mesh and all-aluminum, roll-formed frames
to coordinate with exterior clad colors
➢ Active/Fixed or Fixed/Active operation
➢ Mill-finish extruded aluminum sill with a vinyl thermal break
➢ Heavy vinyl nailing fin
NOTES:
All measurements are nominal.
* Argon gas may not be included with units to be installed in or shipped through high altitude areas.
C l a s s i C s e r i e s v i e w p O r t
Gl a s s: (all door glass is tempered)
➢ H°K LoE� -��0*
➢ H°K LoE� -���*
➢ Patterned-, bronze- or gray-lite
Gr i l l e s :➢ Grilles-in-the-airspace
➢ Interior removable wood grilles with 1-1/8" bars and full surrounds
ot h e r op t i o n s: ➢ Ovolo profile glazing beads and interior grille bars
➢ Handle set and mortise latch in White
➢ Screens with aluminum mesh
➢ Extension jambs in a variety of sizes (shipped loose for field application)
➢ Frame setup
➢ Keyed lock
➢ Secondary security lock
v i e w p O r t O p t i O n a l F e at u r e s
NOTE: All measurements are nominal.
* Argon gas may not be included with units to be installed in or shipped through high altitude areas.
h a r D wa r e
A rustic-colored handle set is included with the Viewport sliding patio
door for field installation. It is also available in White. The mortise
latch is factory installed. A keyed lock or a secondary security lock is
also available.
Vinyl nailing fin applied as standard
Interior view Exterior view
�� ClassiC series
C l a s s i C s e r i e s G a r d e n - a i r e s l i d i n G p at i O d O O r
G a r d e n - a i r e s ta n d a r d F e at u r e s
➢ 1-�/�" thick sash
➢ Standard jamb width is �-9/1�"
➢ Frame setup
➢ �" wide LVL stiles and rails
➢ Constructed of pine, with pine interior stops and wood
mull casings on mulled units
➢ Prefinished, heavy gauge roll-formed aluminum cladding
➢ Tempered, 7/8" H°K LoE�-�70 insulating glass*
➢ Glazed to the interior with wood glazing beads
➢ Fully weatherstripped for a tight seal
➢ Tandem rollers with adjustable, ball-bearing wheels carry the
sliding panel
➢ Rustic-colored handle set and mortise latch
➢ Screens with fiberglass mesh and all aluminum frames to
coordinate with exterior clad colors
➢ One-piece, pultruded fiberglass sill with continuous aluminum sill
nosing and fiberglass sill filler
➢ Thick oak interior threshold
➢ Heavy vinyl nailing fin
NOTES:
All measurements are nominal.
* Argon gas may not be included with units to be installed in or shipped through high altitude areas.
Vinyl nailing fin applied as standard
Gl a s s: (all door glass is tempered)➢ H°K LoE� -��0*
➢ H°K LoE� -���*➢ Patterned-, bronze- or gray-lite➢ Laminated glass➢ Other options standard to the industry
Gr i l l e s :➢ Grilles-in-the-airspace➢ Interior removable wood grilles with 1-1/8" bars and full surrounds➢ PDL with �/8", 7/8", 1-1/8", 1-�/�" or �-1/�" bars
ot h e r op t i o n s: ➢ Other wood species➢ Ovolo profile glazing beads and interior grille bars➢ Interior prefinishing➢ Interior casing➢ Handle set and mortise latch in White➢ Keyed lock➢ Secondary security lock➢ Screens with aluminum mesh ➢ Extension jambs in a wide variety of sizes (shipped loose for field application)
G a r d e n - a i r e O p t i O n a l F e at u r e s
h a r D wa r e
A Rustic-colored handle set is included with the Garden-Aire
sliding patio door for field installation. It is also available in White.
The mortise latch is factory installed. A keyed lock or a secondary
security lock is also available.
Interior view Exterior view
��www.kolbe-kolbe.com
Gl a s s: (all door glass is tempered)
➢ H°K LoE� -��0*
➢ H°K LoE� -���*➢ Patterned-, bronze- or gray-lite➢ Laminated glass➢ Other options standard to the industry
Gr i l l e s :➢ Grilles-in-the-airspace
➢ Interior removable wood grilles with 1-1/8" bars and full surrounds➢ PDL with �/8", 7/8", 1-1/8", 1-�/�" or �-1/�" bars
ot h e r op t i o n s: ➢ Ovolo profile glazing beads and interior grille bars➢ Interior prefinishing➢ Interior casing➢ Toronto or München handle set in Bright Brass, Antique Brass, Satin Nickel, Antique Nickel, Matte Black, Rustic Umber or Oil-rubbed finishes
➢ �-point flush bolt lock on less active panel of French doors➢ Single-point locking system➢ Adjustable, �"x�-�/8" hinges with �/8" radius corners in Bright Brass, Antique Brass, Stainless Steel, Satin Nickel, Antique Nickel, Matte Black, Rustic Umber and Oil-rubbed finishes➢ Non-adjustable, residential, �"x�" ball-bearing hinges with 1/�" radius corners in Bright Brass, Antique Brass, Stainless Steel, Satin Nickel, Antique Nickel, Matte Black and Oil-rubbed finishes➢ Non-adjustable, commercial-grade, �"x�" ball-bearing hinges with square corners in Bright Brass, Antique Brass, Stainless Steel, and Oil-rubbed finishes➢ Non-adjustable, commercial-grade, �-1/�"x�-1/�" hinges in Bright Brass and Oil-rubbed finishes➢ Self-closing, swinging screen includes a spring-loaded lock, fiberglass mesh, and aluminum screen frame to coordinate with exterior clad colors➢ Screens with aluminum mesh➢ Factory-applied extension jambs in a variety of sizes.➢ Thermal handicap sill
i n s w i n G p at i O d O O r s ta n d a r d F e at u r e s
➢ 1-�/�" thick sash panel prehung in the 1-�/1�" frame
➢ Standard jamb width is �-9/1�"
➢ LVL locking stiles; stiles and top rails are a nominal �-�/8" wide;
bottom rail is a nominal 7-9/1�" wide
➢ Constructed of pine, with pine interior stops and wood
mull casings on mulled units
➢ Prefinished, heavy gauge roll-formed aluminum cladding
➢ Tempered, 7/8" H°K LoE�-�70 insulating glass*
➢ Glazed to the interior with wood glazing beads
➢ All exterior wood parts are preservative-treated
➢ Fully weatherstripped for a tight seal
➢ Toronto handle set in a Bright Brass finish
➢ HLS 9000 stainless steel multi-point locking hardware on single
door panels, French doors have a �-point lock on the active panel
and a �-point lock on the less active panel
➢ Adjustable, �"x�-�/8" hinges with �/8" radius corners in a
Gold-painted finish
➢ “Ultra” sliding screens with fiberglass mesh and extruded
aluminum frames to coordinate with exterior clad colors
➢ Bronze-anodized aluminum, self-draining Waterguard™ exterior
sill with an oak interior threshold
➢ Heavy vinyl nailing fin
NOTES:
All measurements are nominal.
* Argon gas may not be included with units to be installed in or shipped through high altitude areas.
Vinyl nailing fin applied as standard
Toronto München
C l a s s i C s e r i e s i n s w i n G p at i O d O O r
i n s w i n G p at i O d O O r O p t i O n a l F e at u r e s
h a r D wa r e
As standard, inswing patio doors feature Gold-painted adjustable hinges and a Toronto handle set in Bright Brass. Optional handle sets and hinges are listed below in Optional Features. For a complete visual list, see pg. 77 in the Entrance Door section.
(shown in Bright Brass)
�� ClassiC series
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Operation is viewed from the exterior.
Grilles are optional. The grille configuration shown for a single panel is typical for each panel.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “KC” before the product number (Ex: KC�0�8).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per panel.)
F.s.r.o.
G.s.
Viewport Patio Doors
6'-1
0 1/
2"6'
-11"
75 9
/16"
3'-5 1/4"3'-5 3/4"
34"
6'-5 1/2"6'-6"34"
9'-10 3/4"9'-11 1/4"
34"
3068 6068 9068
SIDELITE
C l a s s i C s e r i e s v i e w p O r t
v i e w p O r t p at i O d O O r s
D i m e n s i o n C a l C u l a t i o n s
F.S. to Panel O.S.M. +1/�"÷� -� 1/�"Panel O.S.M. to G.S. -�" -� 11/1�"G.S. to D.L.O. -1" -1"note: Clear opening dimensions can be found on pg. 101.
F.S. = Frame Size • G.S. = Glass Size • O.S.M. = Outside MeasurementD.L.O. = Daylight Opening
wiDth heiGht
�7www.kolbe-kolbe.com
C l a s s i C s e r i e s v i e w p O r t
Clad Vertical Section
Viewport with Sidelite – Clad Horizontal Section
Clad Horizontal Section
Standard Viewport Cross Section Drawings
4 1/16"
1/4" UNIT DIM. WIDTH & FRAME WIDTH
ROUGH OPENING WIDTH
4 1/8"
3 3/8" D.L.O.D.L.O.
D.L.O. D.L.O.D.L.O. 3 3/8"
4 1/16"
JamBs
4 1/16"
1/4"
1/4" UNIT DIMENSION WIDTH & FRAME WIDTH
ROUGH OPENING WIDTH
1/4"8 3/16"
JamBs WitH sideLite
3 3/
4"
siLL
Head
FR
AM
E &
UN
IT D
IME
NS
ION
HE
IGH
T
D.L
.O.
4 3/
16"
1 7/32"
1 9/16"
4 9/16"
5 7/8"
standard viewpOrt CrOss seCtiOn drawinGs
Vertical Section Horizontal Section
Drawings are not to scale.Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
Clad Vertical Section
Viewport with Sidelite – Clad Horizontal Section
Clad Horizontal Section
Standard Viewport Cross Section Drawings
4 1/16"
1/4" UNIT DIM. WIDTH & FRAME WIDTH
ROUGH OPENING WIDTH
4 1/8"
3 3/8" D.L.O.D.L.O.
D.L.O. D.L.O.D.L.O. 3 3/8"
4 1/16"
JamBs
4 1/16"
1/4"
1/4" UNIT DIMENSION WIDTH & FRAME WIDTH
ROUGH OPENING WIDTH
1/4"8 3/16"
JamBs WitH sideLite
3 3/
4"
siLL
Head
FR
AM
E &
UN
IT D
IME
NS
ION
HE
IGH
T
D.L
.O.
4 3/
16"
1 7/32"
1 9/16"
4 9/16"
5 7/8"
Viewport with Sidelite - Horizontal Section
�8 ClassiC series
2866 41166 7766 51166 711669166 121663266 4266
F.S.R.O.
G.S.
6'-7
15/
16"
6'-8
7/1
6"72
1/2
"
2'-8"2'-8 1/2"24 3/4"
4'-11"4'-11 1/2"
24 3/4"
7'-7"7'-7 1/2"24 3/4"
3'-2"3'-2 1/2"30 3/4"
5'-11"5'-11 1/2"
30 3/4"
9'-1"9'-1 1/2"30 3/4"
4'-2"4'-2 1/2"42 3/4"
7'-11"7'-11 1/2"
43 3/4"
12'-1"12'-1 1/2"
43 3/4"
SIDELITE SIDELITE SIDELITE
G a r d e n - a i r e s l i d i n G p at i O d O O r s r e m O d e l i n G s i z e s
2968 5068 6068 6668
8068
7968 10068
12368
2980 5080 6080 6680
8080
7980 10080
12380
9368
9380
4368
4380
3668
3680
3368
3380
F.S.R.O.
G.S.
6'-1
0 7/
16"
6'-1
0 15
/16"
75"
8'-2
7/1
6"8'
-2 1
5/16
"91
"
2'-8 1/2"2'-9"
25 1/4"
5'-0"5'-0 1/2"25 1/4"
7'-8 1/2"7'-9"
25 1/4"
3'-2 1/2"3'-3"
31 1/4"
3'-5 1/2"3'-6"
34 1/4"
6'-0"6'-0 1/2"31 1/4"
6'-6"6'-6 1/2"34 1/4"
9'-2 1/2"9'-3"
31 1/4"
9'-11 1/2"10'-0"34 1/4"
F.S.R.O.
G.S.
4'-2 1/2"4'-3"
43 1/4"
8'-0"8'-0 1/2"43 1/4"
12'-2 1/2"12'-3"43 1/4"
6'-1
0 7/
16"
6'-1
0 15
/16"
75"
8'-2
7/1
6"8'
-2 1
5/16
"91
"
SIDELITE
SIDELITE
SIDELITE
SIDELITE SIDELITE
SIDELITE SIDELITE
C l a s s i C s e r i e s G a r d e n - a i r e s l i d i n G p at i O d O O r
G a r d e n - a i r e s l i d i n G p at i O d O O r s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Operation is viewed from the exterior. Standard operation is shown. Please specify if other operation configurations are needed.
Grilles are optional. The grille configuration shown for a single panel is typical for each panel.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “GAC” before the product number (Ex: GAC-1���8).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per panel.)
�9www.kolbe-kolbe.com
C l a s s i C s e r i e s G a r d e n - a i r e s l i d i n G p at i O d O O r
D i m e n s i o n C a l C u l a t i o n s
F.S. to Panel O.S.M. +1/�"÷� -� �/�"Panel O.S.M. to G.S. -�" -� 11/1�"G.S. to D.L.O. -1" -1"notes:Clear opening dimensions can be found on pg. 101.
F.S. = Frame Size • G.S. = Glass Size • O.S.M. = Outside MeasurementD.L.O. = Daylight Opening
2910
2914
2916
3310
3314
3316
2918 3318
2920 3320
2926 3326 4326
4320
4318
4316
4314
4310 5010
5014
5016
5018
5020
5026 6026
6020
6018
6016
6014
6010 8010
8014
8016
8018
8020
8026
2'-8 1/2"2'-9"
25 1/4"
3'-2 1/2"3'-3"
31 1/4"
4'-2 1/2"4'-3"
43 1/4"
5'-0"5'-0 1/2"52 3/4"
F.s.r.o.
G.s.
11 1
/2"
1'-0
"4
1/4"
1'-3
1/2
"1'
-4"
8 1/
4"
1'-5
1/2
"1'
-6"
10 1
/4"
1'-7
1/2
"1'
-8"
12 1
/4"
1'-1
1 1/
2"2'
-0"
16 1
/4"
2'-5
1/2
"2'
-6"
22 1
/4"
Garden-Aire Rectangular Transoms
6'-0"6'-0 1/2"64 3/4"
8'-0"8'-0 1/2"88 3/4"
3610
3614
3616
3618
3620
3626
3'-5 1/2"3'-6"
34 1/4"
6626
6620
6618
6616
6614
6610
6'-6"6'-6 1/2"70 3/4"
G a r d e n - a i r e r e C ta n G u l a r t r a n s O m s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Rectangular transom units are sash set as standard. The units shown are stand-alone units. Adjustments may be required when stacking overother units; adjustments will be made in the factory.
Grille configurations must be specified when ordering.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order transoms, add “GACT” before the product number (Ex: GACT�910).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
wiDth heiGht
70 ClassiC series
standard Garden-aire CrOss seCtiOn drawinGs
Vertical Section Horizontal Section
Garden-Aire with Sidelite - Horizontal Section
reCtanGular transOms staCKed Over Garden-aire dOOrs
Drawings are not to scale.Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
C l a s s i C s e r i e s G a r d e n - a i r e s l i d i n G p at i O d O O r
5 7/
8"
4 9/
16"
5 7/8"
4 9/16"
1 9/16"
4 1/8"
D.L.O. 3 3/8" D.L.O.
4 1/8"
1 9/16"
UNIT DIMENSION WIDTH & FRAME WIDTH
ROUGH OPENING WIDTH
JAMBS
4 9/16"
1 3/4"4
3/16
"
D.L
.O.
4 1/
4"
HEAD
SILL
UN
IT D
IME
NS
ION
HE
IGH
T &
FR
AM
E H
EIG
HT
1 3/16"
RO
UG
H O
PE
NIN
G H
EIG
HT
5 7/8"
4 1/8" 4 1/8"D.L.O.D.L.O.D.L.O. 3 5/16" 8 1/4"
1/4" 1/4"
OPER. STAT. STAT.
ROUGH OPENING WIDTH
UNIT DIMENSION & FRAME WIDTH
5 7/
8"
4 9/
16"
5 7/8"
4 9/16"
1 9/16"
4 1/8"
D.L.O. 3 3/8" D.L.O.
4 1/8"
1 9/16"
UNIT DIMENSION WIDTH & FRAME WIDTH
ROUGH OPENING WIDTH
JAMBS
4 9/16"
1 3/4"4
3/16
"
D.L
.O.
4 1/
4"
HEAD
SILL
UN
IT D
IME
NS
ION
HE
IGH
T &
FR
AM
E H
EIG
HT
1 3/16"
RO
UG
H O
PE
NIN
G H
EIG
HT
5 7/8"
4 1/8" 4 1/8"D.L.O.D.L.O.D.L.O. 3 5/16" 8 1/4"
1/4" 1/4"
OPER. STAT. STAT.
ROUGH OPENING WIDTH
UNIT DIMENSION & FRAME WIDTH
5 7/
8"
4 9/
16"
5 7/8"
4 9/16"
1 9/16"
4 1/8"
D.L.O. 3 3/8" D.L.O.
4 1/8"
1 9/16"
UNIT DIMENSION WIDTH & FRAME WIDTH
ROUGH OPENING WIDTH
JAMBS
4 9/16"
1 3/4"
4 3/
16"
D.L
.O.
4 1/
4"
HEAD
SILL
UN
IT D
IME
NS
ION
HE
IGH
T &
FR
AM
E H
EIG
HT
1 3/16"
RO
UG
H O
PE
NIN
G H
EIG
HT
5 7/8"
4 1/8" 4 1/8"D.L.O.D.L.O.D.L.O. 3 5/16" 8 1/4"
1/4" 1/4"
OPER. STAT. STAT.
ROUGH OPENING WIDTH
UNIT DIMENSION & FRAME WIDTH
3 7/
16"
8 3/
8"
71www.kolbe-kolbe.com
C l a s s i C s e r i e s i n s w i n G p at i O d O O r
F.s.r.o.
G.s.
inswing Patio Door
2'-6 1/4"2'-6 3/4"20 5/16"
4'-11 7/16"4'-11 15/16"
20 5/16"
7'-4 5/8"7'-5 1/8"20 5/16"
6'-7
1/2
"6'
-8"
65 1
1/16
"
7'-1
1 5/
8"8'
-0 1
/8"
81 2
5/32
"
2666 41166AS
2680 41180AS
4'-11 7/16"4'-11 15/16"
20 5/16"
41166SA
41180SA
7566SASR
7580SASR
ACT ACTSTAT ACTSTAT STAT
7'-4 5/8"7'-5 1/8"20 5/16"
7566SASL
7580SASL
ACTSTAT STAT
ACTSTAT STAT ACTSTAT STAT
STAT
ACT ACTSTAT STAT
3'-0 1/4"3'-0 3/4"26 5/16"
3066
3080
5'-11 7/16"5'-11 15/16"
26 5/16"
51166AS
51180AS
ACT STAT
5'-11 7/16"5'-11 15/16"
26 5/16"
51166SA
51180SA
ACTSTAT
ACT STAT ACTSTAT
8'-10 5/8"8'-11 1/8"26 5/16"
81166SASR
81180SASR
8'-10 5/8"8'-11 1/8"26 5/16"
81166SASL
81180SASL
ACTSTAT STAT
ACTSTAT STAT
ACTSTAT STAT
ACTSTAT STAT
i n s w i n G p at i O d O O r s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configuration shown for a single panel is typical for each panel in the unit.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “SPC” before the product number (Ex: SPC81180SASL).
When ordering single units, specify stationary, hinged left or hinged right. Operation is viewed from the interior.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size (Glass sizes are shown per panel.)
D i m e n s i o n C a l C u l a t i o n s
F.S. to Panel O.S.M. (1-wide, active) -1 1�/1�" -� ��/��" (1-wide, stationary) -1 �/�" -� ��/��" (�-wide) -� 9/1�"÷� -� ��/��" (�-wide) -� �/1�"÷� -� ��/��"
Panel O.S.M. to G.S. -8 1/8" -11 �/��"G.S. to D.L.O. -1" -1"note: Clear opening dimensions can be found on pg. 101.
F.S. = Frame Size • G.S. = Glass Size • O.S.M. = Outside MeasurementD.L.O. = Daylight Opening
wiDth heiGht
7� ClassiC series
F.s.r.o.
G.s.
inswing Patio Door – French Door
4'-11 7/16"4'-11 15/16"
20 5/16"
5'-11 7/16"5'-11 15/16"
26 5/16"
6'-7
1/2
"6'
-8"
65 1
1/16
"
7'-1
1 5/
8"8'
-0 1
/8"
81 2
5/32
"
51166AL41166AL
51180AL41180AL
4'-11 7/16"4'-11 15/16"
20 5/16"
41166AR
41180AR
ACT INACT INACT INACT INACTACT
5'-11 7/16"5'-11 15/16"
26 5/16"
51166AR
51180AR
ACTACT
ACT INACT INACT INACT INACTACT ACTACT
2'-6"2'-6 1/2"24 1/2"
3'-0"3'-0 1/2"30 1/2"
4'-11 3/16"4'-11 11/16"
53 11/16"
5'-11 3/16"5'-11 11/16"
65 11/16"
inswing Rectangular transoms
F.s.r.o.
G.s.
0'-1
1 1/
2"1'
-0"
6"
1'-3
1/2
"1'
-4"
10"
1'-5
1/2
"1'
-6"
12"
1'-7
1/2
"1'
-8"
14"
1'-1
1 1/
2"2'
-0"
18"
2'-5
1/2
"2'
-6"
24"
2610 3010 41110 51110
2614 3014 41114 51114
2616 3016 41116 51116
2618 3018 41118 51118
2620 3020 41120 51120
2626 3026 41126 51126
i n s w i n G p at i O d O O r s F r e n C H d O O r s
i n s w i n G r e C ta n G u l a r t r a n s O m s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Grilles are optional. The grille configuration shown for a single panel istypical for each panel in the unit.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order French doors, add “SPC” before the product number
(Ex: SPC�1180AR).
Operation is viewed from the interior.
F.S. = Frame Size • R.O. = Rough Opening
G.S. = Glass Size (Glass sizes are shown per panel.)
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Rectangular transom units are sash set as standard.
The units shown are stand-alone units. Adjustments may be requiredwhen stacking over other units; adjustments will be made in the factory.
Grille configurations must be specified when ordering.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order transoms, add “SPCT” before the product number
(Ex: SPCT��10).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
C l a s s i C s e r i e s i n s w i n G p at i O d O O r
7�www.kolbe-kolbe.com
C l a s s i C s e r i e s i n s w i n G p at i O d O O r
Standard Classique Cross Section Drawings
Clad Vertical Section Clad Horizontal Section
Wood Vertical Section Wood Horizontal Section
1 1/8"
5 17/32"5 13/32" D.L.O.
1/4" 1/4"
ROUGH OPENING WIDTH
FRAME WIDTH
UNIT DIMENSION WIDTH
D.L.O. 5 17/32"5 13/32"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
ALUMINUM WEEP SILL
8-0=
13 1
1/16
"6-
6=9
13/3
2"D
.L.O
.5
13/3
2"
1 1/
8"
1/2"
UN
IT D
IME
NS
ION
HE
IGH
TR
OU
GH
OP
EN
ING
HE
IGH
TF
RA
ME
HE
IGH
T
1/4" 1/4"
Rectangular Transoms Stacked over Classique Doors
Clad Wood
Head
aLUmiNUm WeeP siLL
FR
AM
E &
UN
IT D
IME
NS
ION
HE
IGH
T
RO
UG
H O
PE
NIN
G H
EIG
HT
1 3/8"
9 13
/32"
D.L
.O5
13/3
2"
5 29/32"1/2"
4 9/16"3/4"
8 21
/32" 2 3/
32"
8 21
/32" 2
3/32
"
standard inswinG CrOss seCtiOn drawinGs
Vertical Section Horizontal Section
reCtanGular transOms staCKed Over inswinG dOOrs
Drawings are not to scale.Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
Standard Classique Cross Section Drawings
Clad Vertical Section Clad Horizontal Section
Wood Vertical Section Wood Horizontal Section
1 1/8"
5 17/32"5 13/32" D.L.O.
1/4" 1/4"
ROUGH OPENING WIDTH
FRAME WIDTH
UNIT DIMENSION WIDTH
D.L.O. 5 17/32"5 13/32"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
ALUMINUM WEEP SILL
8-0=
13 1
1/16
"6-
6=9
13/3
2"D
.L.O
.5
13/3
2"
1 1/
8"
1/2"
UN
IT D
IME
NS
ION
HE
IGH
TR
OU
GH
OP
EN
ING
HE
IGH
TF
RA
ME
HE
IGH
T
1/4" 1/4"
Rectangular Transoms Stacked over Classique Doors
Clad Wood
Head
aLUmiNUm WeeP siLL
FR
AM
E &
UN
IT D
IME
NS
ION
HE
IGH
T
RO
UG
H O
PE
NIN
G H
EIG
HT
1 3/8"
9 13
/32"
D.L
.O5
13/3
2"
5 29/32"1/2"
4 9/16"3/4"
8 21
/32" 2 3/
32"
8 21
/32" 2
3/32
"
1 1/8"
5 13/32" D.L.O. D.L.O. 5 13/32"10"
1/4"1/4"ROUGH OPENING WIDTH
FRAME WIDTH
UNIT DIMENSION WIDTH
1 1/8"
5 1/2"9 29/32"D.L.O. D.L.O.5 13/32"
1/4"
1/4"
UNIT DIMENSION WIDTH
FRAME WIDTHROUGH OPENING WIDTH
1/4"
1/4"
D.L.O. 9 31/32"9 29/32"D.L.O. D.L.O. 5 13/32"5 13/32"
UNIT DIMENSION WIDTHROUGH OPENING WIDTH
FRAME WIDTH
5 13/32"10"5 13/32"
1/4"1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
5 1/2"D.L.O.9 29/32"D.L.O.5 13/32"
1/4"1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
5 13/32" D.L.O. D.L.O. D.L.O.9 31/32" 9 29/32" 5 13/32"
1/4" 1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
1 1/8"
D.L.O. D.L.O.
Two-Wide Classique French Doors
Two-Wide Classique Doors - Stationary/Active
Clad Wood
Clad Wood
Three-Wide Classique Doors
Clad
Wood
twO-wide inswinG FrenCH dOOrs twO-wide inswinG dOOrs - statiOnary/aCtive
tHree-wide inswinG dOOrs
1 1/8"
5 13/32" D.L.O. D.L.O. 5 13/32"10"
1/4"1/4"ROUGH OPENING WIDTH
FRAME WIDTH
UNIT DIMENSION WIDTH
1 1/8"
5 1/2"9 29/32"D.L.O. D.L.O.5 13/32"
1/4"
1/4"
UNIT DIMENSION WIDTH
FRAME WIDTHROUGH OPENING WIDTH
1/4"
1/4"
D.L.O. 9 31/32"9 29/32"D.L.O. D.L.O. 5 13/32"5 13/32"
UNIT DIMENSION WIDTHROUGH OPENING WIDTH
FRAME WIDTH
5 13/32"10"5 13/32"
1/4"1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
5 1/2"D.L.O.9 29/32"D.L.O.5 13/32"
1/4"1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
5 13/32" D.L.O. D.L.O. D.L.O.9 31/32" 9 29/32" 5 13/32"
1/4" 1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
1 1/8"
D.L.O. D.L.O.
Two-Wide Classique French Doors
Two-Wide Classique Doors - Stationary/Active
Clad Wood
Clad Wood
Three-Wide Classique Doors
Clad
Wood
1 1/8"
5 13/32" D.L.O. D.L.O. 5 13/32"10"
1/4"1/4"ROUGH OPENING WIDTH
FRAME WIDTH
UNIT DIMENSION WIDTH
1 1/8"
5 1/2"9 29/32"D.L.O. D.L.O.5 13/32"
1/4"
1/4"
UNIT DIMENSION WIDTH
FRAME WIDTHROUGH OPENING WIDTH
1/4"
1/4"
D.L.O. 9 31/32"9 29/32"D.L.O. D.L.O. 5 13/32"5 13/32"
UNIT DIMENSION WIDTHROUGH OPENING WIDTH
FRAME WIDTH
5 13/32"10"5 13/32"
1/4"1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
5 1/2"D.L.O.9 29/32"D.L.O.5 13/32"
1/4"1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
5 13/32" D.L.O. D.L.O. D.L.O.9 31/32" 9 29/32" 5 13/32"
1/4" 1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
1 1/8"
D.L.O. D.L.O.
Two-Wide Classique French Doors
Two-Wide Classique Doors - Stationary/Active
Clad Wood
Clad Wood
Three-Wide Classique Doors
Clad
Wood
7� ClassiC series
entranCe DoorsinswinG entranCe Doors
outswinG entranCe Doors
entranCe Door siDelites
entranCe Door transoms
7�www.kolbe-kolbe.com
Gl a s s: (all door glass is tempered)
➢ H°K LoE� -��0*
➢ H°K LoE� -���*➢ Patterned-, bronze- or gray-lite➢ Laminated glass➢ Other options standard to the industry
Gr i l l e s :➢ Grilles-in-the-airspace➢ Interior removable wood grilles with 1-1/8" bars and full surrounds➢ PDL with �/8", 7/8", 1-1/8", 1-�/�" or �-1/�" bars
ot h e r op t i o n s: ➢ Other wood species➢ Ovolo profile glazing beads and interior grille bars➢ Interior prefinishing➢ Interior casing➢ Toronto or München handle set in Bright Brass, Antique Brass, Satin Nickel, Antique Nickel, Matte Black, Rustic Umber or Oil-rubbed finishes➢ HLS 9000 stainless steel multi-point locking hardware on single panel doors, French doors have a �-point lock on the active panel and a �-point lock on the less active panel
➢ �-point flush bolt lock on less active panel of French doors➢ Single-point locking system➢ Adjustable, �"x�-�/8" hinges with �/8" radius corners in Bright Brass, Antique Brass, Stainless Steel, Satin Nickel, Antique Nickel, Matte Black, Rustic Umber and Oil-rubbed finishes➢ Non-adjustable, residential, �"x�" ball-bearing hinges with 1/�" radius corners in Bright Brass, Antique Brass, Stainless Steel, Satin Nickel, Antique Nickel, Matte Black and Oil-rubbed finishes➢ Non-adjustable, commercial-grade, �"x�" ball-bearing hinges with square corners in Bright Brass, Antique Brass, Stainless Steel, and Oil-rubbed finishes➢ Non-adjustable, commercial-grade, �-1/�"x�-1/�" hinges in Bright Brass and Oil-rubbed finishes➢ “Ultra” sliding screens with fiberglass or aluminum mesh and extruded aluminum frames to coordinate with exterior clad colors➢ Self-closing, swinging screen includes a spring-loaded lock, fiber glass or aluminum mesh, and aluminum screen frame to coordinate with exterior clad colors➢ Extension jambs in a variety of sizes➢ Thermal handicap sill
i n s w i n G e n t r a n C e d O O r O p t i O n a l F e at u r e s
i n s w i n G e n t r a n C e d O O r
s ta n d a r d F e at u r e s
➢ 1-�/�" thick sash panel, prehung in the 1-�/1�" frame
➢ Standard jamb width is �-9/1�"
➢ LVL locking stiles; stiles and top rails are a nominal �-�/8" wide;
bottom rail is a nominal 7 9/1�"
➢ Constructed of pine, with pine interior stops and wood mull
casings on mulled units
➢ Prefinished, heavy gauge roll-formed aluminum cladding
➢ Tempered, 7/8" H°K LoE�-�70 insulating glass
➢ Glazed to the interior with wood glazing beads
➢ All exterior wood parts are preservative-treated
➢ Fully weatherstripped for a tight seal
➢ Adjustable, �"x�-�/8" hinges with �/8" radius corners in a
gold-painted finish
➢ Bronze-anodized aluminum, self-draining Waterguard™ exterior
sill with an oak interior threshold
➢ Heavy vinyl nailing fin
Vinyl nailing fin applied as standard
C l a s s i C s e r i e s i n s w i n G e n t r a n C e d O O r
NOTES:
All measurements are nominal.
* Argon gas may not be included with units to be installed in or shipped through high altitude areas.
7� ClassiC series
C l a s s i C s e r i e s O u t s w i n G e n t r a n C e d O O r
O u t s w i n G e n t r a n C e d O O r
s ta n d a r d F e at u r e s
➢ 1-�/�" thick sash panel, prehung in the 1-1/1�" frame with a 1/�"
rabbeted-in stop
➢ Standard jamb width is �-9/1�"
➢ LVL locking stiles; stiles and top rails are a nominal �-�/8" wide;
bottom rail is a nominal 7-9/1�"
➢ Constructed of pine, with pine interior stops and wood mull
casings on mulled units
➢ Prefinished, heavy gauge roll-formed aluminum cladding
➢ Tempered, 7/8" H°K LoE�-�70 insulating glass
➢ Glazed to the interior with wood glazing beads
➢ All exterior wood parts are preservative-treated
➢ Fully weatherstripped for tight seal
➢ Non-adjustable, residential, �"x�" ball-bearing hinges with 1/�"
radius corners in a Bright Brass finish
➢ Bronze-anodized aluminum bumper sill with oak interior threshold
➢ Heavy vinyl nailing fin
Vinyl nailing fin applied as standard
Gl a s s: (all door glass is tempered)
➢ H°K LoE� -��0*
➢ H°K LoE� -���*➢ Patterned-, bronze- or gray-lite➢ Laminated glass➢ Other options standard to the industry
Gr i l l e s :➢ Grilles-in-the-airspace➢ Interior removable wood grilles with 1-1/8" bars and full surrounds➢ PDL with �/8", 7/8", 1-1/8", 1-�/�" or �-1/�" bars
ot h e r op t i o n s: ➢ Other wood species➢ Ovolo profile glazing beads and interior grille bars➢ Interior prefinishing➢ Interior casing➢ Toronto or München handle set in Bright Brass, Antique Brass, Satin Nickel, Antique Nickel, Matte Black, Rustic Umber or Oil-rubbed finishes
➢ HLS 9000 stainless steel multi-point locking hardware on single panel doors, French doors have a �-point lock on the active panel and a �-point lock on the less active panel➢ �-point flush bolt lock on less active panel of French doors➢ Single-point locking system➢ Non-adjustable, residential, �"x�" ball-bearing hinges with 1/�" radius corners in Antique Brass, Stainless Steel, Satin Nickel, Antique Nickel, Matte Black and Oil-rubbed finishes➢ Adjustable, �"x�-�/8" hinges with �/8" radius corners in Gold-painted, Bright Brass, Antique Brass, Stainless Steel, Satin Nickel, Antique Nickel, Matte Black, Rustic Umber, and Oil-rubbed finishes➢ Non-adjustable, commercial-grade, �"x�" ball-bearing hinges with square corners in Bright Brass, Antique Brass, Stainless Steel and Oil-rubbed finishes➢ Non-adjustable, commercial-grade, �-1/�"x�-1/�" hinges in Bright Brass and Oil-rubbed finishes➢ Extension jambs (up to 1�" applied, over 1�" shipped loose for field application)➢ Thermal or non-thermal handicap sills
O u t s w i n G e n t r a n C e d O O r O p t i O n a l F e at u r e s
NOTES:
All measurements are nominal.
* Argon gas may not be included with units to be installed in or shipped through high altitude areas.
77www.kolbe-kolbe.com
h a r D wa r e
As standard, inswing entrance doors feature Gold-painted adjustable hinges and outswing entrance doors feature Bright Brass �" x �" non-adjustable hinges with 1/�" radius corners. Handle sets, boring or locking systems are not standard on entrance doors. The following hinges and handles are available as an option.
Antique Nickel
Antique Brass
Satin Nickel
BrightBrass
Toronto
München
Adjustable Hinges Non-Adjustable Hinges
Residential, �" x �" ball-bearing, with 1/�" radius corners
Oil-rubbed*
Bright Brass Antique Brass
Matte Black
Gold-painted
Stainless Steel
Rustic Umber
Antique NickelAntique Brass Satin NickelBright Brass
Stainless SteelAntique BrassBright Brass Oil-rubbed*
Bright Brass Oil-rubbed*
Oil-rubbed*
Rustic Umber
Satin Nickel Antique NickelMatte BlackStainless Steel Oil-rubbed*
Commercial-grade, �" x �" ball-bearing, with square corners
Commercial-grade, �-1/�" x �-1/�"
C l a s s i C s e r i e s e n t r a n C e d O O r O p t i O n s
Matte Black
*The Oil-rubbed finish is a living finish, which means that it will change appearance over time with use.
78 ClassiC series
C l a s s i C s e r i e s i n s w i n G e n t r a n C e d O O r
N/AN/AN/AN/A
N/AN/AN/AN/A
N/AN/AN/AN/AN/AN/AN/AN/A
N/AN/AN/AN/AN/AN/AN/AN/AN/A
N/A
N/A
inswing ent. sash Designs
KK610
CXD- 2068 / 4068CXD- 2668 / 5068CXD- 2868 / 5468CXD- 3068 / 6068CXD- 2070 / 4070CXD- 2670 / 5070CXD- 2870 / 5470CXD- 3070 / 6070CXD- 2080 / 4080CXD- 2680 / 5080CXD- 2880 / 5480CXD- 3080 / 6080
Sash Design#:
Pro
duct
I.D
. Code
KK625 KK626 KK635 KK636
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
i n s w i n G e n t r a n C e d O O r s a s H d e s i G n s
NOTES:
Sash designs KK���, KK���, KK��� and KK��� are PDL. If a different grille pattern is
needed, specify sash design KK�10 and the type of grille configuration.
D i m e n s i o n C a l C u l a t i o n s
F.S. to Panel O.S.M. (1-wide, active) -1 1�/1�" -� ��/��" (1-wide, stationary) -1 �/�" -� ��/��" (�-wide) -� 9/1�"÷� -� ��/��" (�-wide) -� �/1�"÷� -� ��/��"
Panel O.S.M. to G.S. (all inswing doors) -8 1/8" -11 �/��"G.S. to D.L.O. -1" -1"notes: Dimension calculations for sidelites and transoms may be obtained from your Kolbe Windows & Doors supplier.Clear opening dimensions can be found on pg. 101.
F.S. = Frame Size • G.S. = Glass Size • O.S.M. = Outside MeasurementD.L.O. = Daylight Opening
wiDth heiGht
79www.kolbe-kolbe.com
F.s.r.o.
G.s.
inswing entrance Doors
2'-1 5/8"2'-2 1/8"15 11/16"
4'-2 3/16"4'-2 11/16"15 11/16"
6'-1
0 23
/32"
6'-1
1 7/
32"
68 2
9/32
"
7'-2
23/
32"
7'-3
7/3
2"72
29/
32"
2068 4068
2070 4070
8'-2
23/
32"
8'-3
7/3
2"84
29/
32"
2080 4080
2'-7 5/8"2'-8 1/8"21 11/16"
5'-2 3/16"5'-2 11/16"21 11/16"
2668 5068
2670 5070
2680 5080
2'-9 5/8"2'-10 1/8"23 11/16"
5'-6 3/16"5'-6 11/16"23 11/16"
2868 5468
2870 5470
2880 5480
3'-1 5/8"3'-2 1/8"27 11/16"
6'-2 3/16"6'-2 11/16"27 11/16"
3068 6068
3070 6070
3080 6080
C l a s s i C s e r i e s i n s w i n G e n t r a n C e d O O r
i n s w i n G e n t r a n C e d O O r s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order inswing entrance doors, add “CXD” before the product number (Ex: CXD�0�8). When ordering single units, specify stationary, hinged left or hinged right. Specify inswing. Operation is viewed from the interior.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
80 ClassiC series
C.P. F.s.r.o.
G.s.*
Premier sidlelites
1'-1 3/4"1'-2 1/4"
7 3/4"
1'-3 3/4"1'-4 1/4"
9 3/4"
1'-5 3/4"1'-6 1/4"11 3/4"
1'-7 3/4"1'-8 1/4"13 3/4"
6'-1
0 23
/32"
6'-1
1 7/
32"
68 2
9/32
"
7'-2
23/
32"
7' 3
7/3
2"72
29/
32"
WXD1068S
WXD1070S
8'-2
23/
32"
8'-3
7/3
2"84
29/
32"
WXD1080S
WXD1268S
WXD1270S
WXD1280S
WXD1468S
WXD1470S
WXD1480S
WXD1668S
WXD1670S
WXD1680S
N/AN/AN/AN/A
N/AN/AN/AN/AN/AN/AN/AN/A
Premier sidelitesash Designs
KK510
WXD1068SWXD1268SWXD1468SWXD1668SWXD1070SWXD1270SWXD1470SWXD1670SWXD1080SWXD1280SWXD1480SWXD1680S
Sash Design#:
Pro
duct
I.D
. Cod
e
KK515 KK516
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
i n s w i n G e n t r a n C e d O O r s i d e l i t e si n s w i n G e n t r a n C e d O O r
s i d e l i t e s a s H d e s i G n s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Sidelite panels are not available as true clad units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order sidelites, use the product code shown and specify clad profile.
Sidelite sash designs KK�1�, KK�1�, and KK�1�0 have PDL. If a different grille pattern is needed, specify sash design KK�10 and the type of grille configuration.
C.P. F.S. = Clad Profile Frame Size • R.O. = Rough Opening • G.S. = Glass Size
C l a s s i C s e r i e s i n s w i n G e n t r a n C e d O O r
81www.kolbe-kolbe.com
C l a s s i C s e r i e s i n s w i n G e n t r a n C e d O O r
2'-7 3/8"2'-7 7/8"25 7/8"
2'-9 3/8"2'-9 7/8"27 7/8"
3'-1 3/8"3'-1 7/8"31 7/8"
inswing entrance Doors - Rectangular transoms
4'-1 15/16"4'-2 7/16"44 7/16"
5'-1 15/16"5'-2 7/16"56 7/16"
5'-5 15/16"5'-6 7/16"60 7/16"
6'-1 15/16"6'-2 7/16"68 7/16"
F.s.r.o.
G.s.
11 1
/2"
1'-0
"6"
1'-3
1/2
"1'
-4"
10"
2'-1 3/8"2'-1 7/8"19 7/8"
1'-5
1/2
"1'
-6"
12"
1'-7
1/2
"1'
-8"
14"
1'-1
1 1/
2"2'
-0"
18"
2'-5
1/2
"2'
-6"
24"
2010
2014
2016
2018
2020
2026
3010
3014
3016
3018
3020
3026
4010
4014
4016
4018
4020
4026
5010
5014
5016
5018
5020
5026
6010
6014
6016
6018
6020
6026
5410
5414
5416
5418
5420
5426
2810
2814
2816
2818
2820
2826
2610
2614
2616
2618
2620
2626
i n s w i n G e n t r a n C e d O O r s r e C ta n G u l a r t r a n s O m s
NOTES:
All measurements are nominal.
Rectangular transom units are sash set as standard.
The units shown are stand-alone units. Adjustments may be required when stacking over other units; adjustments will be made in the factory.
Grille configurations must be specified when ordering.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order transoms, add “CXDT” before the product number (Ex: CXDT�0��). Specify inswing.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
8� ClassiC series
1 1/8"
5 13/32" D.L.O. D.L.O. 5 13/32"10"
1/4"1/4"ROUGH OPENING WIDTH
FRAME WIDTH
UNIT DIMENSION WIDTH
5 13/32"10"D.L.O. D.L.O.5 13/32"
1/4"1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
Rectangular Transoms Stacked over Premier Doors
Clad Wood
Two-Wide Premier French Door
Clad Wood
Premier Door with Sidelite
3 1/2" 8 29/32"D.L.O.
8 21
/32" 2 3/
32"
8 21
/32" 2
3/32
"
twO-wide inswinG entranCe FrenCH dOOrs inswinG entranCe dOOr witH sidelite
reCtanGular transOm staCKed Over inswinG entranCe dOOrs
Standard Premier Cross Section Drawings
1 1/8"
5 17/32"5 13/32" D.L.O.
1/4" 1/4"
ROUGH OPENING WIDTHFRAME WIDTH
UNIT DIMENSION WIDTH
D.L.O. 5 17/32"5 13/32"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
ALUMINUM WEEP SILL
7-0=
15 3
/16"
6-8=
11 3
/16"
D.L
.O.
5 13
/32"
1 1/
8"
1/2"
UN
IT D
IME
NS
ION
HE
IGH
TR
OU
GH
OP
EN
ING
HE
IGH
TF
RA
ME
HE
IGH
T
1/4"1/4"
Clad Vertical Section Clad Horizontal Section
Wood Vertical Section Wood Horizontal Section
Raised Panel Door - Wood Vertical Section
22 3
/4"
11 3
/32"
RO
UG
H O
PE
NIN
G H
EIG
HT
FR
AM
E H
EIG
HT
UN
IT D
IME
NS
ION
HE
IGH
T
8"35
3/8
"6
1/16
"
1 25/64"
4 9/16"5 5/8"
3/4"
1/2"
6'-8" EXAMPLE HEIGHT
8-0=
13 1
1/16
"
ALUMINUM WEEP SILL
Head
aLUmiNUm WeeP siLL
FR
AM
E &
UN
IT D
IME
NS
ION
HE
IGH
T
RO
UG
H O
PE
NIN
G H
EIG
HT
1 3/8"
9 13
/32"
D.L
.O5
13/3
2"5 29/32"1/2"
4 9/16"3/4"
standard inswinG entranCe dOOr CrOss seCtiOn drawinGs
Vertical Section Horizontal Section
Drawings are not to scale.Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
1 1/8"
5 13/32" D.L.O. D.L.O. 5 13/32"10"
1/4"1/4"ROUGH OPENING WIDTH
FRAME WIDTH
UNIT DIMENSION WIDTH
5 13/32"10"D.L.O. D.L.O.5 13/32"
1/4"1/4"
ROUGH OPENING WIDTH
UNIT DIMENSION WIDTH & FRAME WIDTH
Rectangular Transoms Stacked over Premier Doors
Clad Wood
Two-Wide Premier French Door
Clad Wood
Premier Door with Sidelite
3 1/2" 8 29/32"D.L.O.
8 21
/32" 2 3/
32"
8 21
/32" 2
3/32
"
C l a s s i C s e r i e s i n s w i n G e n t r a n C e d O O r
5 13/32" D.L.O. 9 29/32" D.L.O. 5 1/2"
4 9/
16"
5 29
/32"
1/4"FRAME & UNIT DIMENSION WIDTHROUGH OPENING WIDTH
1/4"
8�www.kolbe-kolbe.com
N/AN/AN/AN/A
N/AN/AN/AN/A
N/AN/AN/AN/AN/AN/AN/AN/A
N/AN/AN/AN/AN/AN/AN/AN/AN/A
N/A
N/A
outswing ent. sash Designs
KK610
CXD- 2068 / 4068CXD- 2668 / 5068CXD- 2868 / 5468CXD- 3068 / 6068CXD- 2070 / 4070CXD- 2670 / 5070CXD- 2870 / 5470CXD- 3070 / 6070CXD- 2080 / 4080CXD- 2680 / 5080CXD- 2880 / 5480CXD- 3080 / 6080
Sash Design#:
Pro
duct
I.D
. Code
KK625 KK626 KK635 KK636
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
O u t s w i n G e n t r a n C e d O O r s a s H d e s i G n s
NOTES:
Sash designs KK���, KK���, KK��� and KK��� have PDL. If a different grille pattern is needed,
specify sash design KK�10 and the type of grille configuration.
D i m e n s i o n C a l C u l a t i o n s
F.S. to Panel O.S.M. (1-wide) -� 1�/��" -� �7/��"
Panel O.S.M. to G.S. (1-wide) (�-8, 7-0, 8-0 hts.) -8 1/8" -11 1/8" (�-� ht., patio) -8 1/8" -11 �/��" (8-0 ht., patio) -8 1/8" -11 1/8"Panel Opening Width to G.S. (�-wide) -17 �/8"÷�F.S. to Panel Opening Width -� 1/8" G.S. to D.L.O. -1" -1"note: Dimension calculations for sidelites and transoms may be obtained from your Kolbe Windows & Doors supplier.Clear opening dimensions can be found on pg. 101.
F.S. = Frame Size • G.S. = Glass Size • O.S.M. = Outside MeasurementD.L.O. = Daylight Opening
wiDth heiGht
C l a s s i C s e r i e s O u t s w i n G e n t r a n C e d O O r
8� ClassiC series
F.s.r.o.
G.s.
outswing entrance Doors – Clad
2'-8 23/32"2'-9 7/32"21 11/16"
5'-3 3/8"5'-3 7/8"21 11/16"
2'-2 23/32"2'-3 7/32"15 11/16"
4'-3 3/8"4'-3 7/8"15 11/16"
6'-1
0 27
/32"
6'-1
1 11
/32"
68 7
/8"
7'-2
27/
32"
7'-3
11/
32"
72 7
/8"
CXD2668 CXD5068
CXD2670 CXD5070
8'-2
27/
32"
8'-3
11/
32"
84 7
/8"
CXD2680 CXD5080
CXD2068 CXD4068
CXD2070 CXD4070
CXD2080 CXD4080
2'-10 23/32"2'-11 7/32"23 11/16"
5'-7 3/8"5'-7 7/8"23 11/16"
CXD2868 CXD5468
CXD2870 CXD5470
CXD2880 CXD5480
3'-2 23/32"3'-3 7/32"27 11/16"
6'-3 3/8"6'-3 7/8"27 11/16"
CXD6068
CXD3070 CXD6070
CXD3080 CXD6080
CXD3068
F.s.r.o.
G.s.
outswing Patio Doors – Clad2'-7 11/32"2'-7 27/32"
20 5/16"
5'-0 5/8"5'-1 1/8"20 5/16"
6'-7
5/8
"6'
-8 1
/8"
65 1
1/16
"
7'-1
1 23
/32"
8'-0
7/3
2"81
3/4
"
SPC2666 SPC41166
SPC2680 SPC41180
3'-1 11/32"3'-1 27/32"
26 5/16"
6'-0 5/8"6'-1 1/8"26 5/16"
SPC3066 SPC51166
SPC3080 SPC51180
O u t s w i n G e n t r a n C e d O O r s
O u t s w i n G p at i O d O O r s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Dimensions are given for active units; dimensions of stationary units may vary.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order doors, use the product number shown and specify outswing. When ordering single units, specify stationary, hinged left or hinged right. Operation is viewed from the exterior.
F.S. = Frame Size
R.O. = Rough Opening
G.S. = Glass Size
C l a s s i C s e r i e s O u t s w i n G e n t r a n C e d O O r
8�www.kolbe-kolbe.com
C.P. F.s.r.o.
G.s.*
outswing ext. Door sidlelites – Clad Profile1'-2 3/4"1'-3 1/4"
7 5/8"
1'-4 3/4"1'-5 1/4"
9 5/8"
1'-6 3/4"1'-7 1/4"11 5/8"
1'-8 3/4"1'-9 1/4"13 5/8"
6'-1
0 27
/32"
6'-1
1 11
/32"
68 1
/8"
7'-2
27/
32"
7' 3
11/
32"
72 1
/8"
WXD1068S
WXD1070S
8'-2
27/
32"
8' 3
11/
32"
84 1
/8"
WXD1080S
WXD1268S
WXD1270S
WXD1280S
WXD1468S
WXD1470S
WXD1480S
WXD1668S
WXD1670S
WXD1680S
N/AN/AN/AN/A
N/AN/AN/AN/AN/AN/AN/AN/A
outswing sidelitesash Designs
KK510
WXD1068SWXD1268SWXD1468SWXD1668SWXD1070SWXD1270SWXD1470SWXD1670SWXD1080SWXD1280SWXD1480SWXD1680S
Sash Design#:
Pro
duct
I.D
. Cod
e
KK515 KK516
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
O u t s w i n G e n t r a n C e d O O r s i d e l i t e s O u t s w i n G e n t r a n C e d O O r
s i d e l i t e s a s H d e s i G n s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Sidelite panels are not available as true clad units.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order sidelites, use the product code shown and specify clad profile.
Sidelite sash designs KK�1�, KK�1�, and KK�1�0 have PDL. If a different grille pattern is needed, specify sash design KK�10 and the type of grille configuration.
C.P. F.S. = Clad Profile Frame Size
R.O. = Rough Opening • G.S. = Glass Size
C l a s s i C s e r i e s O u t s w i n G e n t r a n C e d O O r
8� ClassiC series
2'-10 23/32"2'-11 7/32"28 19/32"
3'-2 23/32"3'-3 7/32"32 19/32"
5'-3 3/8"5'-3 7/8"57 1/4"
4'-3 3/8"4'-3 7/8"45 1/4"
Clad outswing ext. Doors - Rectangular transoms5'-7 3/8"5'-7 7/8"61 1/4"
6'-3 3/8"6'-3 7/8"69 1/4"
F.s.r.o.
G.s.
11 1
/2"
1'-0
"5
3/8"
1'-3
1/2
"1'
-4"
9 3/
8"
2'-8 23/32"2'-9 7/32"26 19/32"
2'-2 23/32"2'-3 7/32"20 19/32"
1'-5
1/2
"1'
-6"
11 3
/8"
1'-7
1/2
"1'
-8"
13 3
/8"
1'-1
1 1/
2"2'
-0"
17 3
/8"
2'-5
1/2
"2'
-6"
23 3
/8"
CXDT2610
CXDT2614
CXDT2616
CXDT2618
CXDT2620
CXDT2626
CXDT2010
CXDT2014
CXDT2016
CXDT2018
CXDT2020
CXDT2026
CXDT5010
CXDT5014
CXDT5016
CXDT5018
CXDT5020
CXDT5026
CXDT4010
CXDT4014
CXDT4016
CXDT4018
CXDT4020
CXDT4026
CXDT5410
CXDT5414
CXDT5416
CXDT5418
CXDT5420
CXDT5426
CXDT6010
CXDT6014
CXDT6016
CXDT6018
CXDT6020
CXDT6026
CXDT3010
CXDT3014
CXDT3016
CXDT3018
CXDT3020
CXDT3026
CXDT2810
CXDT2814
CXDT2816
CXDT2818
CXDT2820
CXDT2826
O u t s w i n G e n t r a n C e d O O r s r e C ta n G u l a r t r a n s O m s
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Rectangular transom units are sash set as standard.
The units shown are stand-alone units. Adjustments may be required when stacking over other units; adjustments will be made in the factory.
Transom dimensions shown are for units stacked above active doors; dimensions for transoms stacked above stationary doors may vary.
Grille configurations must be specified when ordering.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order transoms, use the product number shown.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
2'-7 11/32"2'-7 27/32"
25 1/4"
3'-1 11/32"3'-1 27/32"
31 1/4"
5'-0 5/8"5'-1 5/8"54 1/2"
6'-0 5/8"6'-1 5/8"66 1/2"
transoms for outswing Patio Door sizesF.s.
r.o.G.s.
11 1
/2"
1'-0
"5
3/8"
1'-3
1/2
"1'
-4"
9 3/
8"
1'-5
1/2
"1'
-6"
11 3
/8"
1'-7
1/2
"1'
-8"
13 3
/8"
1'-1
1 1/
2"2'
-0"
17 3
/8"
2'-5
1/2
"2'
-6"
23 3
/8"
SPCT2610 SPCT3010 SPCT41110 SPCT51110
SPCT2614 SPCT3014 SPCT41114 SPCT51114
SPCT2616 SPCT3016 SPCT41116 SPCT51116
SPCT2618 SPCT3018 SPCT241118 SPCT51118
SPCT2620 SPCT3020 SPCT41120 SPCT51120
SPCT2626 SPCT3026 SPCT41126 SPCT51126
O u t s w i n G p at i O d O O r s r e C ta n G u l a r t r a n s O m s
C l a s s i C s e r i e s O u t s w i n G e n t r a n C e d O O r
87www.kolbe-kolbe.com
Rectangular Transoms Stacked over Manor Doors
Clad Wood
Two-Wide Manor French Door
Clad Wood
Manor Door with Sidelite
3 13/16" D.L.O. 9 5/8"
1/4"5 23/32" 10 1/16"
FRAME WIDTHROUGH OPENING WIDTHUNIT DIMENSION WIDTH
1 1/4"
1 9/16"
D.L.O.D.L.O.1/4"
1 9/16"
4 9/
16"
5 5/
8"
5 23/32"
3 1/
4"
9 9/
32"
9 9/
32"
3 1/
2"
5 31/32"D.L.O.5 31/32"
FRAME & UNIT DIMENSION WIDTH
10 1/16" D.L.O.
4 9/
16"
5 15
/16"
twO-wide OutswinG FrenCH dOOrs OutswinG entranCe dOOr witH sidelite
reCtanGular transOm staCKed Over OutswinG entranCe dOOrs
Standard Manor Cross Section Drawings
Clad Vertical Section Clad Horizontal Section
Wood Vertical Section Wood Horizontal Section
Raised Panel Door - Wood Vertical Section
1/4"
1 1/4"
D.L.O.5 13/16" 5 23/32"
UNIT DIMENSION WIDTH
ROUGH OPENING WIDTH
FRAME WIDTH1/4"
1/2"
aLUmiNUm siLL6'-8" EXAMPLE HEIGHT
22 3
/4"
10 5
/8"
1 63/64"
4 9/16"
UN
IT D
IME
NS
ION
HE
IGH
TR
OU
GH
OP
EN
ING
HE
IGH
TF
RA
ME
HE
IGH
T8"
35 3
/8"
5 13
/16"
5 5/8"
1 9/16"
1/2"
aLUmiNUm siLL
Head
7-0
= 1
4 3/
4"8-
0 =
13
1/4"
*6-6
= 8
31/
32"
*8-0
= 1
3 1/
4"
RO
UG
H O
PE
NIN
G H
EIG
HT
6-8
= 1
0 3/
4"
UN
IT D
IME
NS
ION
HE
IGH
T
* CLASSIQUE SIZES
FR
AM
E H
EIG
HT
D.L
.O.
5 23
/32"
1 63/64"
5 5/8"
4 9/16"
1 9/16"
ALUMINUM SILL
FR
AM
E &
UN
IT D
IME
NS
ION
HE
IGH
T
D.L
.O.
8 31
/32"
5 31
/32"
1 63/64"
5 15/16"
4 9/16"
1 9/16"
FRAME & UNIT DIMENSION WIDTH
5 31/32" D.L.O. 6 1/16"
4 9/
16"
5 15
/16"
standard OutswinG entranCe dOOr CrOss seCtiOn drawinGs
Vertical Section Horizontal Section
Drawings are not to scale.Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
Rectangular Transoms Stacked over Manor Doors
Clad Wood
Two-Wide Manor French Door
Clad Wood
Manor Door with Sidelite
3 13/16" D.L.O. 9 5/8"
1/4"5 23/32" 10 1/16"
FRAME WIDTHROUGH OPENING WIDTHUNIT DIMENSION WIDTH
1 1/4"
1 9/16"
D.L.O.D.L.O.1/4"
1 9/16"
4 9/
16"
5 5/
8"
5 23/32"
3 1/
4"
9 9/
32"
9 9/
32"
3 1/
2"
5 31/32"D.L.O.5 31/32"
FRAME & UNIT DIMENSION WIDTH
10 1/16" D.L.O.
4 9/
16"
5 15
/16"
C l a s s i C s e r i e s O u t s w i n G e n t r a n C e d O O r
3 11/16"
5 15/16" 6 1/32"
12 1/16"
88 ClassiC series
Complementary raDius units
GeometriC units
89www.kolbe-kolbe.com
Gl a s s:➢ H°K LoE� -��0*
➢ H°K LoE� -���*
➢ Patterned-, bronze- or gray-lite
➢ Tempered or laminated
➢ Other options standard to the industry
Gr i l l e s :➢ Grilles-in-the-airspace
➢ Interior removable wood grilles with 7/8" or 1-1/8" bars and
full surrounds
➢ PDL with �/8", 7/8", 1-1/8", 1-�/�" or �-1/�" bars
ot h e r op t i o n s: ➢ Other wood species
➢ Ovolo profile glazing beads and interior grille bars
➢ Interior prefinishing
➢ Interior casing
➢ Glazing may be direct set (clad profile only)
➢ Extended legs or no legs on half-circles
➢ Extension jambs (up to 1�" applied, over 1�" shipped loose for
field application)
r a d i u s O p t i O n a l F e at u r e s
NOTES:
All measurements are nominal.
* Argon gas may not be included with units to be installed in or shipped through high altitude areas.
r a d i u s s ta n d a r d F e at u r e s
➢ 1-�/�" thick sash
➢ Overall jamb width is �-9/1�" (basic box width matches the unit
being complemented)
➢ �" straight legs on half-circles
➢ Constructed of pine, with pine interior stops and wood mull
casings on mulled units
➢ Prefinished, extruded aluminum cladding
➢ 7/8" H°K LoE�-�70 insulating glass*
➢ Glazing is sash set to the interior with wood glazing beads
➢ All exterior wood parts are preservative-treated
➢ Fully weatherstripped for a tight seal
➢ Standard radius shapes include quarter-circles, half-circles,
full-circles, ovals and ellipticals
➢ Heavy vinyl nailing fin
Vinyl nailing fin applied as standard
C l a s s i C s e r i e s r a d i u s
90 ClassiC series
Dimension calculation formulas for radius units vary depending on the unit and application. Please contact your Kolbe supplier if formulas are needed.
D i m e n s i o n C a l C u l a t i o n s
C l a s s i C s e r i e s r a d i u s
r a d i u s d i v i d e d l i t e p at t e r n s
Sunburst
Double Cut Sunburst
Triple Cut Sunburst
Open Hub Sunburst
Starburst
Spider Web
Elliptical Sunburst
�-1/�" PDL bars are not available for patterns with curved bars.
91www.kolbe-kolbe.com
C l a s s i C s e r i e s r a d i u s
H a l F - C i r C l e u n i t s C a s e m e n t
F.S.R.O.
G.S.
Half-Circle Units to match Casements
F.S.R.O.
G.S.
F.S.R.O.
G.S.
1'-8"1'-8 1/2"15 1/4"
1'-1
"1'
-1 1
/2"
8 1/
4"
2'-0"2'-0 1/2"19 1/4"
1'-3
"1'
-3 1
/2"
10 1
/4"
1'-6
"1'
-6 1
/2"
13 1
/4"
2'-6"2'-6 1/2"25 1/4"
RTKN1 RTKW1 RTKX1
F.S.R.O.
G.S.
1'-9
"1'
-9 1
/2"
16 1
/4"
3'-0"
3'-0 1/2"31 1/4"
RTK30/E1
F.S.R.O.
G.S.
3'-4"3'-4 1/2"35 1/4"
RTKN2
1'-1
1"1'
-11
1/2"
18 1
/4"
F.S.R.O.
G.S.
3'-6"3'-6 1/2"
37"
RTK36
2' 0
"2'
0-1
/2"
19 1
/4"
F.S.R.O.
G.S.
2'-3
"2'
-3 1
/2"
22 1
/4"
4'-0"4'-0 1/2"43 1/4"
RTKW2
F.S.R.O.
G.S.
5'-0"5'-0 1/2"55 1/4"
RTKX2
2'-9
"2'
-9 1
/2"
28 1
/4"
F.S.R.O.
G.S.
6'-0"6'-0 1/2"67 1/4"
RTKW3
3'-3
"3'
-3 1
/2"
34 1
/4"
F.S.R.O.
G.S.
4'-0
"4'
-0 1
/2"
43 1
/4"
7'-6"7'-6 1/2"85 1/4"
RTKX3
F.S.R.O.
G.S.
8'-0"8'-0 1/2"91 1/4"
4'-3
"4'
-3 1
/2"
46 1
/4"
RTKW4
F.S.R.O.
G.S.
1'-7
"1'
-7 1
/2"
14 1
/4"
2'-8"2'-8 1/2"27 1/4"
RTKS2
F.S.R.O.
G.S.
2'-4"2'-4 1/2"23 1/4"
1'-5
"1'
-5 1
/2"
12 1
/4"
RTKL1
F.S.R.O.
G.S.
2'-7
"2'
-7 1
/2"
26 1
/4"
4'-8"4'-8 1/2"51 1/4"
RTKL2
F.S.R.O.
G.S.
7'-0"7'-0 1/2"79 1/4"
RTKL3
3'-9
"3'
-9 1
/2"
40 1
/4"
F.S.R.O.
G.S.
1'-4"1'-4 1/2"11 1/4"
0'-1
1"0'
-11
1/2"
6 1/
4"
RTKS1
H a l F - C i r C l e u n i t s d O u b l e H u n G
F.s.r.o.
G.s.
Half-Circle units to match Double Hungs
F.s.r.o.
G.s.
F.s.r.o.
G.s.
F.s.r.o.
G.s.
1'-9 1/2"1'-10"
16"
1'
-1 3
/4"
1'-2
1/4
"8
1/4"
RT16DH
2'-1 1/2"2'-2"20"
1'-3
3/4
"1'
-4 1
/4"
10 1
/4"
RT20DH 1'-5
3/4
"1'
-6 1
/4"
12 1
/4"
2'-5 1/2"2'-6"24"
RT24DH
F.s.r.o.
G.s.
3'-1 1/2"3'-2"32"
RT32DH1'-9
3/4
"1'
-10
1/4"
16 1
/4"
F.s.r.o.
G.s.
3'-5 1/2"3'-6"36"
RT36DH1'-1
1 3/
4"2'
-0 1
/4"
18 1
/4"
F.s.r.o.
G.s.
1'-7
3/4
"1'
-8 1
/4"
14 1
/4"
2'-9 1/2"
2'-10"28"
RT28DH
2'-1
3/4
"2'
-2 1
/4"
20 1
/4"
3'-9 1/2"3'-10"
40"
RT40DH
F.s.r.o.
G.s.
4'-3"4'-3 1/2"45 1/2"
RT20-2DH
2'-4
1/2
"2'
-5"
23"
F.s.r.o.
G.s.
3'-7"3'-7 1/2"37 1/2"
RT16-2DH
2'-0
1/2
"2'
-1"
19"
F.s.r.o.
G.s.
4'-11"4'-11 1/2"
53 1/2"
RT24-2DH
2'-8
1/2
"2'
-9"
27"
F.s.r.o.
G.s.
3'-0
1/2
"3'
-1"
31"
5'-7"5'-7 1/2"61 1/2"
RT28-2DH
F.s.r.o.
G.s.
3'-4
1/2
"3'
-5"
35"
RT32-2DH
6'-3"6'-3 1/2"69 1/2"
F.s.r.o.
G.s.
3'-8
1/2
"3'
-9"
39"
RT36-2DH
6'-11"6'-11 1/2"
77 1/2"
F.s.r.o.
G.s.
4'-0
1/2
"4'
-1"
43"
RT40-2DH
7'-7"7'-7 1/2"85 1/2"
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Radius units are sash set as standard. Direct set units are available only in wood. Glass sizes differ for direct set units. Contact your supplier for details.
The units shown are stand-alone units. Adjustments may be required when stacking over other units; adjustments will be made in the factory.
Grilles are optional. Grille pattern options are shown on pg. 90.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order radius units, add “C” before the product number (Ex: CRTKW�).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
9� ClassiC series
C l a s s i C s e r i e s r a d i u s
Half-Circle units to match Viewports
F.s.r.o.
G.s.
6'-5 1/2"6'-6"72"
RTK60
3'-5
3/4
"3'
-6 1
/4"
36 1
/4"
H a l F - C i r C l e u n i t s v i e w p O r t s l i d i n G p at i O d O O r
Half-Circle units to match Garden-aires
F.s.r.o.
G.s.
5'-0"5'-0 1/2"54 1/2"
2'-9
"2'
-9 1
/2"
27 1
/2"
RTG50
F.s.r.o.
G.s.
4'-11"4'-11 1/2"
53 1/2"
2'-8
1/2
"2'
-9"
27"
RTG411
F.s.r.o.
G.s.
6'-0"6'-0 1/2"66 1/2"
RTG603'
-3"
3'-3
1/2
"33
1/2
"
F.s.r.o.
G.s.
5'-11"5'-11 1/2"
65 1/2"
RTG511
3'-2
1/2
"3'
-3"
33"
F.s.r.o.
G.s.
4'-3
"4'
-3 1
/2"
45 1
/2"
7'-11"
7'-11 1/2"90 1/2"
RTG711
F.s.r.o.
G.s.
4'-2
1/2
"4'
-3"
45"
8'-0"
8'-0 1/2"90 1/2"
RTG80
F.s.r.o.
G.s.
6'-6"6'-6 1/2"72 1/2"
RTG66
3'-6
"3'
-6 1
/2"
36 1
/2"
H a l F - C i r C l e u n i t s G a r d e n - a i r e s l i d i n G p at i O d O O r
Half-Circle units to match inswing
F.s.r.o.
G.s.
F.s.r.o.
G.s.
RTS411
4'-11 3/16"4'-11 11/16"
53 11/16"
2'-8
19/
32"
2'-9
1/8
"27
1/8
"
RTS511
3'-2
19/
32"
3'-3
1/8
"33
1/8
"
5'-11 3/16"5'-11 11/16"
65 11/16"
F.s.r.o.
G.s.
RTS26
2'-6"2'-6 1/2"24 1/2"
1'-6
"1'
-6 1
/2"
12 1
/2"
F.s.r.o.
G.s.
RTS30
3'-0"3'-0 1/2"30 1/2"
1'-9
"1'
-9 1
/2"
15 1
/2"
H a l F - C i r C l e u n i t s i n s w i n G p at i O d O O r
Half-Circle units to match inswing entrance Doors
F.s.r.o.
G.s.
3'-1 3/8"3'-1 7/8"31 7/8"
1'-9
11/
16"
1'-1
0 3/
16"
16 3
/16"
RTXD30
F.s.r.o.
G.s.
RTXD50
F.s.r.o.
G.s.
F.s.r.o.
G.s.
2'-3
31/
32"
2'-4
1/2
"22
1/2
"
4'-1 15/16"4'-2 7/16"42 7/16"
RTXD40
5'-5 15/16"5'-6 7/16"60 7/16"
RTXD542'-1
1 31
/32"
3'-0
1/2
"30
1/2
"
F.s.r.o.
G.s.
3'-3
31/
32"
3'-4
1/2
"34
1/2
"
6'-1 15/16"6'-2 7/16"68 7/16"
RTXD60
5'-1 15/16"5'-2 7/16"56 7/16"
2'-9
31/
32"
2'-1
0 1/
2"28
1/2
"
F.s.r.o.
G.s.
2'-1 3/8"2'-1 7/8"19 7/8"
1'-3
11/
16"
1'-4
3/1
6"10
3/1
6"
RTXD20
F.s.r.o.
G.s.
2'-7 3/8"2'-7 7/8"25 7/8"
1'-6
11/
16"
1'-7
3/1
6"13
3/1
6"
RTXD26
F.s.r.o.
G.s.
2'-9 3/8"2'-9 7/8"27 7/8"
1'-7
11/
16"
1'-8
3/1
6"14
3/1
6"
RTXD28
H a l F - C i r C l e u n i t s i n s w i n G e n t r a n C e d O O r
NOTES:All measurements are nominal. Elevation charts are not to scale.
Radius units are sash set as standard. Direct set units are available only in wood. Glass sizes differ for direct set units. Contact your supplier for details.
The units shown are stand-alone units. Adjustments may be required when stacking over other units; adjust-ments will be made in the factory.
Grilles are optional. Grille pattern options are shown on pg. 90.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order radius units, add “C” before the product number (Ex: CRTG80). Specify inswing entrance door when ordering inswing door half-circles.
F.S. = Frame Size
R.O. = Rough Opening
G.S. = Glass Size
9�www.kolbe-kolbe.com
C l a s s i C s e r i e s r a d i u s
RTS30*
F.s.r.o.
G.s.
2'-2 23/32"2'-3 7/32"
20 1/2"
1'-4
3/8
"1'
-4 7
/8"
10 1
/8"
RTXD20
F.s.r.o.
G.s.21 3/8"2'-3 1/8"2'-2 5/8"
1'-4 5/16"1'-4 13/16"
10 1/16"
(for stationary door)
(for active door)F.s.
r.o.G.s.
2'-8 23/32"2'-9 7/32"
26 1/2"
1'-7
3/8
"1'
-7 7
/8"
13 1
/8"
RTXD26
F.s.r.o.
G.s.27 3/8"2'-9 1/8"2'-8 5/8"
1'-7 5/16"1'-7 13/16"
13 1/16"
(for stationary door)
(for active door)F.s.
r.o.G.s.
2'-7 11/32"2'-7 27/32"
25 1/8"
1'-6
11/
16"
1'-7
3/1
6"12
7/1
6"
RTS26*
F.s.r.o.
G.s.25"2'-7 3/4"2'-7 1/4"
1'-6 5/8"1'-7 1/8"12 3/8"
(for stationary door)
(for active door)
F.s.r.o.
G.s.
2'-10 23/32"2'-11 7/32"
28 1/2"
1'-8
3/8
"1'
-8 7
/8"
14 1
/8"
F.s.r.o.
G.s.28 3/8"2'-11 1/8"2'-10 5/8"
1'-8 5/16"1'-8 13/16"
14 1/16"
(for stationary door)
(for active door)
RTXD28
F.s.r.o.
G.s.
3'-1 11/32"3'-1 27/32"
31 1/8"
1'-9
11/
16"
1'-1
0 3/
16"
15 7
/16"
F.s.r.o.
G.s.31"3'-1 3/4"3'-1 1/4"
1'-9 5/8"1'-10 1/8"
15 3/8"
(for stationary door)
(for active door)
RTXD30
F.s.r.o.
G.s.
3'-2 23/32"3'-3 7/32"
32 1/2"
1'-1
0 3/
8"1'
-10
7/8"
16 1
/8"
F.s.r.o.
G.s.32 3/8"3'-3 1/8"3'-2 5/8"
1'-10 5/16"1'-10 13/16"
16 1/16"
(for stationary door)
(for active door)
CLad/CLad ProFiLe dimeNsioNs
SINGLE DOORSH a l F - C i r C l e u n i t s O n e - w i d e O u t s w i n G e n t r a n C e d O O r
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Radius units are sash set as standard. Direct set units are available only in wood. Glass sizes differ for direct set units. Contact your supplier for details.
The units shown are stand-alone units. Adjustments may be required when stacking over other units; adjustments will be made in the factory.
Grilles are optional. Grille pattern options are shown on pg. 90.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
* Patio door sizes
PRODUCT CODES:
To order radius units, add “C” before the product number
(Ex: CRTXD��). Specify outswing door, active or stationary.
† RTXD�0 is not available as a true clad unit but can be ordered as clad profile. Add “W” before the product number. Specify outswing entrance door, clad profile.
F.S. = Frame Size
R.O. = Rough Opening
G.S. = Glass Size
RTXD50
RTXD54 RTS511
RTS411
RTXD60
DOUBLE DOORS
r.o.G.s.
F.s.
2'-9
15/
16"
2'-9
13/
16"
27 1
/16"
5'-0 5/8"5'-1 1/8"54 3/8"
r.o.G.s.
F.s.
2'-1
0 11
/16"
2'-1
1 3/
16"
28 7
/16"
5'-3 3/8"5'-3 7/8"57 1/8"
r.o.G.s.
F.s. 3'-0 11/16"3'-1 3/16"30 7/16"
61 1
/8"
5'-7
7/8
"5'
-7 3
/8"
CLad dimeNsioNs
r.o.G.s.
F.s. 3'-3 5/16"3'-3 13/16"
33 1/16"
66 3
/8"
6'-1
1/8
"6'
-0 5
/8"
r.o.G.s.
F.s.
3'-4
11/
16"
3'-5
3/1
6"34
7/1
6"
6'-3 3/8"6'-3 7/8"69 1/8"
r.o.G.s.
WRTXD40†
F.s. 2'-4 11/16"2'-5 3/16"22 7/16"
45 1
/8"
4'-3
7/8
"4'
-3 3
/8"
H a l F - C i r C l e u n i t s t w O - w i d e O u t s w i n G e n t r a n C e d O O r
9� ClassiC series
e l l i p t i C a l u n i t s C a s e m e n t
F.s.r.o.
G.s.
4'-0"4'-0 1/2"43 1/4"
elliptical units to match Casements
1'-6
"1'
-6 1
/2"
13 1
/4"
EHKW2
5'-0"5'-0 1/2"55 1/4"
EHKX2
6'-0"6'-0 1/2"67 1/4"
EHKW3
7'-6"7'-6 1/2"85 1/4"
WEHKX3
8'-0"8'-0 1/2"91 1/4"
WEHKW4
e l l i p t i C a l u n i t s d O u b l e H u n G
F.s.r.o.
G.s.
elliptical units to match Double Hungs
3'-7"3'-7 1/2"37 1/2"
1'-6
"1'
-6 1
/2"
12 1
/2"
4'-3"4'-3 1/2"45 1/2"
4'-11"4'-11 1/2"
53 1/2"
WEH16-2DH WEH20-2DH WEH24-2DH
5'-7"
5'-7 1/2"61 1/2"
6'-3"6'-3 1/2"69 1/2"
EH28-2DH EH32-2DH
6'-11"6'-11 1/2"
77 1/2"
7'-7"7'-7 1/2"85 1/2"
WEH36-2DH WEH40-2DH
F.s.r.o.
G.s.
1'-6
"1'
-6 1
/2"
12 1
/2"
5'-4 1/2
5'-5"59"
6'-4 1/2"6'-5"71"
WEH16-3DH WEH20-3DH
7'-4 1/2"7'-5"83"
8'-4 1/2"8'-5"95"
9'-4 1/2"9'-5"
107 1/8"
10'-4 1/2"10'-5"119"
WEH24-3DH WEH28-3DH WEH32-3DH WEH36-3DH
e l l i p t i C a l u n i t s v i e w p O r t
F.s.r.o.
G.s.
elliptical units to match Viewports
1'-6
"1'
-6 1
/2"
12 1
/2"
WEHK60
6'-5 1/2"6'-6"72"
e l l i p t i C a l u n i t s G a r d e n - a i r e s l i d i n G p at i O d O O r
F.s.r.o.
G.s.
elliptical units to match Garden-aires
1'-6
"1'
-6 1
/2"
12 1
/2"
F.s.r.o.
G.s.
1'-6
"1'
-6 1
/2"
12 1
/2"
5'-0"5'-0 1/2"54 1/2"
6'-0"6'-0 1/2"66 1/2"
7'-11"7'-11 1/2"
89 1/2"
WEHG50 WEHG60
WEHG711
4'-11"4'-11 1/2"
53 1/2"
WEHG411
5'-11"5'-11 1/2"
65 1/2"
WEHG511
8'-0"8'-0 1/2"90 1/2"
WEHG80
6'-6"6'-6 1/2"72 1/2"
WEHG66
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Radius units are sash set as standard. Direct set units are available only in wood. Glass sizes differ for direct set units. Contact your supplier for details.
The units shown are stand-alone units. Adjustments may be required when stacking over other units;adjustments will be made in the factory.
Grilles are optional. Grille pattern options are shown on pg. 90.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “C” for clad before the product number (Ex: CEHKW�).
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
C l a s s i C s e r i e s r a d i u s
9�www.kolbe-kolbe.com
C l a s s i C s e r i e s r a d i u s
F.s.r.o.
G.s.
elliptical units to match inswing
1'-6
"1'
-6 1
/2"
12 1
/2"
4'-11 3/16"4'-11 11/16"
53 11/16"
5'-11 3/16"5'-11 11/16"
65 11/16"
WEHS411 EHS511
e l l i p t i C a l u n i t s i n s w i n G e n t r a n C e d O O r
F.s.r.o.
G.s.
elliptical units to match inswing entrance Doors
5'-1 15/16"5'-2 7/16"56 9/16"
1'-6
"1'
-6 1
/2"
12 1
/2"
EHXD50 WEHXD60
4'-1 15/16"4'-2 7/16"44 9/16"
5'-5 15/16"5'-6 7/16"60 9/16"
WEHXD54WEHXD40
6'-1 15/16"6'-2 7/16"68 9/16"
e l l i p t i C a l u n i t s O u t s w i n G e n t r a n C e d O O r
F.s. 5'-7 3/8"5'-7 7/8"60 7/8"
1'-6
"1'
-6 1
/2"
11 7
/8"
6'-3 3/8"6'-3 7/8"68 7/8"
5'-3 3/8"5'-3 7/8"56 7/8"
r.o.G.s.
EHXD50 WEHXD60WEHXD54WEHXD40
outswing entrance elliptical
4'-3 3/8"4'-3 7/8"45 7/8"
e l l i p t i C a l u n i t s O u t s w i n G p at i O d O O r
F.s.r.o.
G.s.
6'-0 5/8"6'-1 1/8"67 1/8"
1'-6
"1'
-6 1
/2"
11 7
/8"
EHS511
5'-0 5/8"5'-1 1/8"55 1/8"
WEHS411
outswing Patio door
e l l i p t i C a l u n i t s i n s w i n G p at i O d O O r
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Radius units are sash set as standard. Direct set units are available only in wood.Glass sizes differ for direct set units. Contact your supplier for details.
The units shown are stand-alone units. Adjustments may be required when stacking over other units; adjustments will be made in the factory.
Grilles are optional. Grille pattern options are shown on pg. 90.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines.
For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order units, add “C” for clad before the product number (Ex: CEHXD�0). Specify inswing patio, inswing entrance or outswing entrance door when ordering.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
9� ClassiC series
F.s.r.o.
G.s.
Quarter-Circle units to match Casements
F.s.r.o.
G.s.
F.s.r.o.
G.s.
F.s.r.o.
G.s.
1'-8"1'-8 1/2"15 1/4"
1'-1
1"1'
-11
1/2"
18 1
/4"
RTQRN1
2'-0"2'-0 1/2"19 1/4"
2'-3
"2'
-3 1
/2"
22 1
/4"
RTQRW1
2'-9
"2'
-9 1
/2"
28 1
/4"
2'-6"
2'-6 1/2"25 1/4"
RTQRX1
3'-0"3'-0 1/2"31 1/4"
RTQRK30
3'-3
"3'
-3 1
/2"
34 1
/4"
CLad U.d.r.o.
G.s.
4'-3
"4'
-3 1
/2"
46 1
/4"
4'-0"4'-0 1/2"43 1/4"
RTQRW2
Q u a r t e r - C i r C l e u n i t s C a s e m e n t
F.s.r.o.
G.s.
Quarter-Circle units to match Double Hungs
2'-1 1/2"2'-2"20"
2'-4
1/2
"2'
-5"
23"
RTQR20
F.s.r.o.
G.s.
RTQR24
2'-5 1/2"2'-6"24"
2'-8
1/2
"2'
-9"
27"
F.s.r.o.
G.s.
3'-0
1/2
"3'
-1"
31"
2'-9 1/2"
2'-10"28"
RTQR28
F.s.r.o.
G.s.
3'-1 1/2"3'-2"32"
RTQR32
3'-4
1/2
"3'
-5"
35"
Q u a r t e r - C i r C l e u n i t s d O u b l e H u n G
F.s.r.o.
G.s.
Full Circle units
2'-0"2'-0 1/2"19 1/4"
(hei
ghts
equ
al w
idth
s)
2'-6"2'-6 1/2"25 1/4"
3'-0"3'-0 1/2"31 1/4"
3'-6"3'-6 1/2"37 1/4"
4'-0"4'-0 1/2"43 1/4"
6'-0"6'-0 1/2"67 1/4"
FC2-0 FC2-6 FC3-0 FC3-6 FC4-0FC6-0
F u l l C i r C l e u n i t s
F.s.r.o.
G.s.
oval units
1'-8"1'-8 1/2"15 1/4"
2'-0"2'-0 1/2"19 1/4"
3'-0"3'-0 1/2"31 1/4"
2'-6
"2'
-6 1
/2"
25 1
/4"
F.s.r.o.
G.s.
3'-0
"3'
-0 1
/2"
31 1
/4"
F.s.r.o.
G.s.
4'-6
"4'
-6 1
/2"
49 1
/4"
WOV1-8*OV2-0
OV3-0
O va l u n i t s
(casement profile only for clad units)
(casement profile only for clad units)
NOTES:
All measurements are nominal. Elevation charts are not to scale.
Radius units are sash set as standard. Direct set units are available only in wood. Glass sizes differ for direct set units. Contact your supplier for details.
The units shown are stand-alone units. Adjustments may be required whenstacking over other units; adjustments will be made in the factory.
Grilles are optional. Grille pattern options are shown on pg. 90.
Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/�" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 101.
PRODUCT CODES:
To order clad radius units, add “C” before the product number (Ex: CFC�-0).
* WOV1-8 is not available as a true clad unit, but can be ordered as cladprofile. Use the product number shown and specify clad profile.
F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size
C l a s s i C s e r i e s r a d i u s
97www.kolbe-kolbe.com
C l a s s i C s e r i e s r a d i u s
Clad Radius Unit Cross Section Drawings
To MatchCasements
To MatchDouble Hungs &
Doors (except Manor)
JamB
siLL
FR
AM
E H
EIG
HT
1 29
/32"
1 29
/32"
FR
AM
E H
EIG
HT
2 7/
8"D
.L.O
D.L
.O.
1 1/16"
2 7/
8"2
7/8"
FR
AM
E H
EIG
HT
D.L
.O.
1 29
/32"
4 9/16"
5 5/8"
4 9/16"
5 5/8"
1 1/16"
1 1/16"
Head
JAMB
SILL
5 7/8"
4 9/16"
11/1
6"
1 13
/16"
FR
AM
E H
EIG
HT
3 1/
4"
5 7/8"
4 9/16"
1 13
/16"
11/1
6"
FR
AM
E W
IDT
H
3 1/
4"
FR
AM
E H
EIG
HT
3 1/
4"
1 13
/16"
5 7/8"
4 9/16"
11/1
6"
Clad radius unit CrOss seCtiOn drawinGs
To MatchCasements
To MatchDouble Hungs &
Doors
Drawings are not to scale.Additional and the most current drawings are available after registration and sign-on at www.kolbe-kolbe.com
Clad radius unit staCKinG detail drawinGs
Stacked over Casements Stacked over Double HungsStacked over Viewportor Garden-Aire Doors
Stacked over Inswing Patio or InswingEntrance Doors
Stacked over Outswing Entrance Doors
9 1/
4"
6 15
/32"
9 1/
4"
6 15
/32"
9 1/
4"
6 15
/32"
98 ClassiC series
Divided Lite Cross Section Drawings
H°K insulating glass with 7/8" WRG
H°K insulating glass with 1-1/8" WRG
H°K insulating glass with �/8" PDL bar
H°K insulating glass with 7/8" ovolo WRG
H°K insulating glass with 1-1/8" ovoloWRG
H°K insulating glass with �/8" ovolo PDL bar
C l a s s i C s e r i e s d i v i d e d l i t e s
divided lite CrOss seCtiOn drawinGs
H°K insulating glass with 7/8" removable grilles
H°K insulating glass with 7/8" ovolo removable grilles
Drawings are not to scale.
H°K insulating glass with �/8" PDL
H°K insulating glass with �/8" ovolo PDL
H°K insulating glass with 1-1/8" removable grilles
H°K insulating glass with1-1/8" ovolo removable grilles
99www.kolbe-kolbe.com
Divided Lite Cross Section Drawings
H°K insulating glass with 7/8" PDL
H°K insulating glass with 1-1/8" PDL
H°K insulating glass with 1-�/�" PDL bar
H°K insulating glass with �-1/�" PDL bar
H°K insulating glass with 7/8" ovolo PDL
H°K insulating glass with 1-1/8" ovolo PDL
H°K insulating glass with 1-�/�" ovolo PDL bar
H°K insulating glass with �-1/�" ovolo PDL bar
C l a s s i C s e r i e s d i v i d e d l i t e s
divided lite CrOss seCtiOn drawinGs
H°K insulating glass with 1-1/8" PDL
H°K insulating glass with 1-�/�" PDL
H°K insulating glass with 1-1/8" ovolo PDL
H°K insulating glass with 1-�/�" ovolo PDL
Drawings are not to scale.
H°K insulating glass with �-1/�" PDL
H°K insulating glass with �-1/�" ovolo PDL
H°K insulating glass with 7/8" PDL
H°K insulating glass with 7/8" ovolo PDL
100 ClassiC series
teChniCal Data Clear openinG Data
enerGy perFormanCe Data
101www.kolbe-kolbe.com
Notes For CasemeNt WiNdoWs:
➢ Clear opening widths shown are for standard casements with multi-point locks and concealed hinges. If the following hinge options are used, the clear opening widths will need to be adjusted as noted:
exposed Hinges (a.k.a. euro Hinges) - The Euro hinge is the default hinge used when standard concealed casement hinges can not be utilized (radius head units), or if this type of hinge is requested.
In most cases single-arm operators are used with Euro hinges, which changes the clear opening widths. For units with this type of hinge, add 3-7/16" to widths shown for one sash open. For French casements add 6-7/8" to widths shown for two sash open. Two sash open may or may not be considered as an acceptable emergency escape and rescue opening per the local building inspector. Please remember that if box locks and exposed hinges are used together, the adjustments must be combined.
➢ All dimensions are taken with sash open to 90°, except for an “E” Series unit with dual-arm operator and concealed hinges, which opens to 75°.➢ Shaded units meet most national building codes for emergency escape and rescue requirements.
deFiNitioNs oF aCCePtaBLe emerGeNCY esCaPe & resCUe oPeNiNGs:
“Egress” has long been the term used to describe the clear opening dimensions of a window or door necessary to enter or exit a building in case of an emergency. With the release of the International Building Code (IBC) and International Residential Code (IRC), “egress” is no longer the appropriate term.
The International Codes (IBC 2000 & 2003, IRC 2000 & 2003) now use the phrase “Emergency Escape & Rescue Opening.” IBC and IRC have set the following as basic requirements for Emergency Escape & Rescue Openings.
➢ Minimum Opening Width: 20 inches (508 mm)➢ Minimum Opening Height: 24 inches (610 mm)➢ Minimum Opening Area: 5.7 sq. ft. (0.53 m2)
Note:Please check your local codes to confirm that these Emergency Escape & Rescue Opening requirements are applicable. Other require-ments may also apply.
C l e a r O p e n i n G d i m e n s i O n s
roUGH oPeNiNG reCommeNdatioNs:
The Kolbe standard rough opening dimensions published in our product literature are provided as a guideline to maintain a minimum 1/4” space between the window or patio door and the building structure. There are certain situations where Kolbe recommends a gap larger than our published 1/4” standard:
➢ When installation clips are used, the gap should be increased to 1/2” on the sides, top and bottom of the unit.➢ When mulls are installed in the opening, the gap all around should be increased to 1/2”. For installation consistency, the same gap should be used on all units in the project.➢ If a sill pan drainage system is used, the gap should be increased to 1/2” on the top and bottom of the unit.
Because every installation is different, Kolbe strongly recommends consultation with the local supplier or an experienced contractor, architect or structural engineer prior to the installation of any Kolbe product. Installation of Kolbe products, including sizing of rough opening, method of attachment, fastener selection, and code compliance is the sole responsibility of the architect, building owner, contractor and/or consumer. Unless otherwise specified, if units are ordered by rough opening, Kolbe will size the units using our standard minimum 1/4” gap - regardless of the options or construction of the product ordered.
Product #
sq. Ft. Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft. Vent
sq. Ft. of Unit Frame dim.
Width Height
Casements
S12 0.99 7-5/16" 19-1/2" 1.30 1.59 2.67
S126 1.29 7-5/16" 25-1/2" 1.73 2.08 3.33
S13 1.60 7-5/16" 31-1/2" 2.15 2.57 4.00
S136 1.90 7-5/16" 37-1/2" 2.58 3.06 4.67
S14 2.21 7-5/16" 43-1/2" 3.01 3.55 5.33
S146 2.51 7-5/16 49-1/2" 3.43 4.04 6.00
S15 2.82 7-5/16" 55-1/2" 3.86 4.53 6.67
S156 3.12 7-5/16" 61-1/2" 4.29 5.02 7.33
S16 3.43 7-5/16" 67-1/2" 4.72 5.51 8.00
N12 1.53 11-5/16" 19-1/2" 1.81 2.13 3.33
N126 2.00 11-5/16" 25-1/2" 2.40 2.79 4.17
N13 2.47 11-5/16" 31-1/2" 2.99 3.45 5.00
N136 2.95 11-5/16" 37-1/2" 3.59 4.10 5.83
N14 3.42 11-5/16" 43-1/2" 4.18 4.76 6.67
N146 3.89 11-5/16" 49-1/2" 4.77 5.41 7.50
N15 4.36 11-5/16" 55-1/2" 5.37 6.07 8.33
N156 4.83 11-5/16" 61-1/2" 5.96 6.73 9.17
N16 5.30 11-5/16" 67-1/2" 6.56 7.83 10.00
W12 2.07 15-5/16" 19-1/2" 2.31 2.67 4.00
W126 2.71 15-5/16" 25-1/2" 3.07 3.50 5.00
W13 3.35 15-5/16" 31-1/2" 3.83 4.32 6.00
W136 3.99 15-5/16" 37-1/2" 4.59 5.14 7.00
W14 4.63 15-5/16" 43-1/2" 5.35 5.97 8.00
W146 5.26 15-5/16" 49-1/2" 6.12 6.79 9.00
W15 5.90 15-5/16" 55-1/2" 6.88 7.61 10.00
W156 6.54 15-5/16" 61-1/2" 7.64 8.43 11.00
W16 7.18 15-5/16" 67-1/2" 8.40 9.26 12.00
L12 2.62 19-5/16" 19-1/2" 2.82 3.22 4.67
L126 3.42 19-5/16" 25-1/2" 3.75 4.21 5.83
L13 4.22 19-5/16" 31-1/2" 4.67 5.20 7.00
L136 5.03 19-5/16" 37-1/2" 5.60 6.18 8.17
L14 5.83 19-5/16" 43-1/2" 6.53 7.17 9.33
L146 6.64 19-5/16" 49-1/2" 7.46 8.16 10.50
L15 7.44 19-5/16" 55-1/2" 8.38 9.15 11.67
L156 8.25 19-5/16" 61-1/2" 9.31 10.14 12.83
L16 9.05 19-5/16" 67-1/2" 10.24 11.13 14.00
X12 2.89 21-5/16" 19-1/2" 3.07 3.49 5.00
X126 3.77 21-5/16" 25-1/2" 4.08 4.56 6.25
X13 4.66 21-5/16" 31-1/2" 5.09 5.63 7.50
X136 5.55 21-5/16" 37-1/2" 6.10 6.71 8.75
X14 6.44 21-5/16" 43-1/2" 7.12 7.78 10.00
X146 7.33 21-5/16" 49-1/2" 8.13 8.85 11.25
X15 8.21 21-5/16" 55-1/2" 9.14 9.92 12.50
X156 9.10 21-5/16" 61-1/2" 10.15 11.00 13.75
X16 9.99 21-5/16" 67-1/2" 11.16 12.07 15.00
E13 5.63 25-3/4" 31-1/2" 6.35 6.95 9.00
10� ClassiC series
C l e a r O p e n i n G d i m e n s i O n s
Product #
sq. Ft. Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft. Vent
sq. Ft. of Unit Frame
dim.Width Height
Casements (continued)
E136 6.71 25-3/4" 37-1/2" 7.62 8.27 10.50
E14 7.78 25-3/4" 43-1/2" 8.88 9.59 12.00
E146 8.85 25-3/4" 49-1/2" 10.14 10.91 13.50
E15 9.92 25-3/4" 55-1/2" 11.40 12.24 15.00
E156 11.00 25-3/4" 61-1/2" 12.66 13.56 16.50
E16 12.07 25-3/4" 67-1/2" 13.92 14.88 18.00
Product#
sq. Ft. Clear opg.
Clear opg. WidthClear opg. Ht.
sq. Ft.
d.L.o.
sq. Ft.
Vent
sq. Ft. of Unit
Frame dim.
1 open
2 open
1 open 2 open
French Casements
N23 2.66 5.71 12-3/16" 26-3/16" 31-3/8" 6.35 7.93 10.00
N236 3.16 6.80 12-3/16" 26-3/16" 37-3/8" 7.62 9.44 11.67
N24 3.67 7.89 12-3/16" 26-3/16" 43-3/8" 8.88 10.96 13.33
N246 4.18 8.98 12-3/16" 26-3/16" 49-3/8" 10.14 12.47 15.00
N25 4.69 10.07 12-3/16" 26-3/16" 55-3/8" 11.40 13.99 16.67
N256 5.19 11.16 12-3/16" 26-3/16" 61-3/8" 12.66 15.50 18.33
N26 5.70 12.25 12-3/16" 26-3/16" 67-3/8" 13.92 17.02 20.00
W23 3.53 7.45 16-3/16" 34-3/16" 31-3/8" 8.04 9.67 12.00
W236 4.20 8.87 16-3/16" 34-3/16" 37-3/8" 9.63 11.52 14.00
W24 4.88 10.30 16-3/16" 34-3/16" 43-3/8" 11.22 13.37 16.00
W246 5.55 11.72 16-3/16" 34-3/16" 49-3/8" 12.82 15.22 18.00
W25 6.22 13.15 16-3/16" 34-3/16" 55-3/8" 14.41 17.06 20.00
X23 4.83 10.06 22-3/16" 46-3/16" 31-3/8" 10.56 12.28 15.00
X236 5.76 11.99 22-3/16" 46-3/16" 37-3/8" 12.65 14.63 17.50
X24 6.68 13.91 22-3/16" 46-3/16" 43-3/8" 14.74 16.98 20.00
X246 7.61 15.84 22-3/16" 46-3/16" 49-3/8" 16.84 19.33 22.50
X25 8.53 17.76 22-3/16" 46-3/16" 55-3/8" 18.93 21.68 25.00
Notes For aWNiNG WiNdoWs:➣ Awnings may not be considered emergency and rescue windows.➣ Clear opening dimensions determined after unhooking and retracting operator arms and pushing sash open to 90º.➣ If multi-point locks are used deduct 5/8" from the clear opening widths show here.➣ If exposed (Euro) hinges are used in lieu of concealed hinges, add 3-3/8" to the clear opening heights shown here.
Product #
sq. Ft.
Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft. Vent
sq. Ft. of Unit Frame dim.
Width Height
Awnings
26181 1.97 26-3/8" 10-3/4" 2.40 1.48 4.17
30181 2.42 32-3/8" 10-3/4" 2.99 1.82 5.00
36181 2.86 38-3/8" 10-3/4" 3.59 2.15 5.83
40181 3.31 44-3/8" 10-3/4" 4.18 2.49 6.67
26201 2.70 26-3/8" 14-3/4" 3.07 1.48 5.00
30201 3.32 32-3/8" 14-3/4" 3.83 1.82 6.00
36201 3.93 38-3/8" 14-3/4" 4.59 2.15 7.00
40201 4.55 44-3/8" 14-3/4" 5.35 2.49 8.00
26261 3.80 26-3/8" 20-3/4" 4.08 1.48 6.25
30261 4.67 32-3/8" 20-3/4" 5.09 1.82 7.50
36261 5.53 38-3/8" 20-3/4" 6.10 2.15 8.75
40261 6.39 44-3/8" 20-3/4" 7.12 2.49 10.00
26301 4.90 26-3/8" 26-3/4" 5.09 1.48 7.50
30301 6.01 32-3/8" 26-3/4" 6.35 1.82 9.00
36301 7.13 38-3/8" 26-3/4" 7.62 2.15 10.50
40301 8.24 44-3/8" 26-3/4" 8.88 2.49 12.00
10�www.kolbe-kolbe.com
C l e a r O p e n i n G d i m e n s i O n s
Product#
sq. Ft. Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft.
Vent
sq. Ft. of Unit Frame dim.
Width Height
Traditional Double Hungs
1614 1.70 18-1/4" 13-7/16" 2.71 1.70 5.44
1616 1.96 18-1/4" 15-7/16" 3.13 1.96 6.04
1620 2.46 18-1/4" 19-7/16" 3.96 2.46 7.23
1622 2.72 18-1/4" 21-7/16" 4.38 2.72 7.83
1624 2.97 18-1/4" 23-7/16" 4.79 2.97 8.43
1626 3.22 18-1/4" 25-7/16" 5.21 3.22 9.02
1628 3.48 18-1/4" 27-7/16" 5.63 3.48 9.62
1630 3.73 18-1/4" 29-7/16" 6.04 3.73 10.22
1632 3.98 18-1/4" 31-7/16" 6.46 3.98 10.82
1634 4.24 18-1/4" 33-7/16" 6.88 4.24 11.41
1636 4.49 18-1/4" 35-7/16" 7.29 4.49 12.01
2014 2.08 22-1/4" 13-7/16" 3.43 2.08 6.45
2016 2.39 22-1/4" 15-7/16" 3.96 2.39 7.16
2020 3.00 22-1/4" 19-7/16" 5.01 3.00 8.58
2022 3.31 22-1/4" 21-7/16" 5.54 3.31 9.29
2024 3.62 22-1/4" 23-7/16" 6.07 3.62 9.99
2026 3.93 22-1/4" 25-7/16" 6.60 3.93 10.70
2028 4.24 22-1/4" 27-7/16" 7.13 4.24 11.41
2030 4.55 22-1/4" 29-7/16" 7.65 4.55 12.12
2032 4.86 22-1/4" 31-7/16" 8.18 4.86 12.83
2034 5.17 22-1/4" 33-7/16" 8.71 5.17 13.54
2036 5.48 22-1/4" 35-7/16" 9.24 5.48 14.24
2414 2.45 26-1/4" 13-7/16" 4.15 2.45 7.47
2416 2.81 26-1/4" 15-7/16" 4.79 2.81 8.28
2420 3.54 26-1/4" 19-7/16" 6.07 3.54 9.92
2422 3.91 26-1/4" 21-7/16" 6.71 3.91 10.74
2424 4.27 26-1/4" 23-7/16" 7.35 4.27 11.56
2426 4.64 26-1/4" 25-7/16" 7.99 4.64 12.38
2428 5.00 26-1/4" 27-7/16" 8.63 5.00 13.20
2430 5.37 26-1/4" 29-7/16" 9.26 5.37 14.02
2432 5.73 26-1/4" 31-7/16" 9.90 5.73 14.84
2434 6.10 26-1/4" 33-7/16" 10.54 6.10 15.66
2436 6.46 26-1/4" 35-7/16" 11.18 6.46 16.48
2614 2.64 28-1/4" 13-7/16" 4.51 2.64 7.97
2616 3.03 28-1/4" 15-7/16" 5.21 3.03 8.85
2620 3.81 28-1/4" 19-7/16" 6.60 3.81 10.60
2622 4.21 28-1/4" 21-7/16" 7.29 4.21 11.47
2624 4.60 28-1/4" 23-7/16" 7.99 4.60 12.35
2626 4.99 28-1/4" 25-7/16" 8.68 4.99 13.22
2628 5.38 28-1/4" 27-7/16" 9.38 5.38 14.10
2630 5.77 28-1/4" 29-7/16" 10.07 5.77 14.97
2632 6.17 28-1/4" 31-7/16" 10.76 6.17 15.85
2634 6.56 28-1/4" 33-7/16" 11.46 6.56 16.72
2636 6.95 28-1/4" 35-7/16" 12.15 6.95 17.60
2814 2.82 30-1/4" 13-7/16" 4.88 2.82 8.48
2816 3.24 30-1/4" 15-7/16" 5.63 3.24 9.41
Product#
sq. Ft. Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft.
Vent
sq. Ft. of Unit Frame dim.
Width Height
Traditional Double Hungs (continued)
2820 4.08 30-1/4" 19-7/16" 7.13 4.08 11.27
2822 4.50 30-1/4" 21-7/16" 7.88 4.50 12.20
2824 4.92 30-1/4" 23-7/16" 8.63 4.92 13.13
2826 5.34 30-1/4" 25-7/16" 9.38 5.34 14.06
2828 5.76 30-1/4" 27-7/16" 10.13 5.76 14.99
2830 6.18 30-1/4" 29-7/16" 10.88 6.18 15.92
2832 6.60 30-1/4" 31-7/16" 11.63 6.60 16.85
2834 7.02 30-1/4" 33-7/16" 12.38 7.02 17.78
2836 7.44 30-1/4" 35-7/16" 13.13 7.44 18.71
3014 3.01 32-1/4" 13-7/16" 5.24 3.01 8.98
3016 3.46 32-1/4" 15-7/16" 6.04 3.46 9.97
3020 4.35 32-1/4" 19-7/16" 7.65 4.35 11.94
3022 4.80 32-1/4" 21-7/16" 8.46 4.80 12.93
3024 5.25 32-1/4" 23-7/16" 9.26 5.25 13.91
3026 5.70 32-1/4" 25-7/16" 10.07 5.70 14.90
3028 6.14 32-1/4" 27-7/16" 10.88 6.14 15.89
3030 6.59 32-1/4" 29-7/16" 11.68 6.59 16.87
3032 7.04 32-1/4" 31-7/16" 12.49 7.04 17.86
3034 7.49 32-1/4" 33-7/16" 13.29 7.49 18.84
3036 7.94 32-1/4" 35-7/16" 14.10 7.94 19.83
3214 3.20 34-1/4" 13-7/16" 5.60 3.20 9.49
3216 3.67 34-1/4" 15-7/16" 6.46 3.67 10.53
3220 4.62 34-1/4" 19-7/16" 8.18 4.62 12.61
3222 5.10 34-1/4" 21-7/16" 9.04 5.10 13.66
3224 5.57 34-1/4" 23-7/16" 9.90 5.57 14.70
3226 6.05 34-1/4" 25-7/16" 10.76 6.05 15.74
3228 6.53 34-1/4" 25-7/16" 11.63 6.53 16.78
3230 7.00 34-1/4" 29-7/16" 12.49 7.00 17.82
3232 7.48 34-1/4" 31-7/16" 13.35 7.48 18.86
3234 7.95 34-1/4" 33-7/16" 14.21 7.95 19.91
3236 8.43 34-1/4" 35-7/16" 15.07 8.43 20.95
3614 3.57 38-1/4" 13-7/16" 6.32 3.57 10.50
3616 4.10 38-1/4" 15-7/16" 7.29 4.10 11.65
3620 5.16 38-1/4" 19-7/16" 9.24 5.16 13.96
3622 5.69 38-1/4" 21-7/16" 10.21 5.69 15.11
3624 6.23 38-1/4" 23-7/16" 11.18 6.23 16.27
3626 6.76 38-1/4" 25-7/16" 12.15 6.76 17.42
3628 7.29 38-1/4" 27-7/16" 13.13 7.29 18.57
3630 7.82 38-1/4" 29-7/16" 14.10 7.82 19.72
3632 8.35 38-1/4" 31-7/16" 15.07 8.35 20.88
3634 8.88 38-1/4" 33-7/16" 16.04 8.88 22.03
3636 9.41 38-1/4" 35-7/16" 17.01 9.41 23.18
4014 3.94 42-1/4" 13-7/16" 7.04 3.94 11.51
4016 4.53 42-1/4" 15-7/16" 8.13 4.53 12.78
4020 5.70 42-1/4" 19-7/16" 10.29 5.70 15.31
4022 6.29 42-1/4" 21-7/16" 11.38 6.29 16.57
10� ClassiC series
Product#
sq. Ft. Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft. Vent
sq. Ft. of Unit Frame dim.
Width Height
Double Sliders
1616 1.94 15-3/8" 18-1/8" 3.13 1.94 6.10
1620 2.36 15-3/8" 22-1/8" 3.96 2.36 7.17
1624 2.79 15-3/8" 26-1/8" 4.79 2.79 8.24
1628 3.22 15-3/8" 30-1/8" 5.63 3.22 9.31
1632 3.64 15-3/8" 34-1/8" 6.46 3.64 10.38
1636 4.07 15-3/8" 38-1/8" 7.29 4.07 11.45
1640 4.50 15-3/8" 42-1/8" 8.13 4.50 12.52
1644 4.92 15-3/8" 46-1/8" 8.96 4.92 13.59
1648 5.35 15-3/8" 50-1/8" 9.79 5.35 14.65
2016 2.44 19-3/8" 18-1/8" 3.96 2.44 7.37
2020 2.98 19-3/8" 22-1/8" 5.01 2.98 8.66
2024 3.52 19-3/8" 26-1/8" 6.07 3.52 9.95
2028 4.05 19-3/8" 30-1/8" 7.13 4.05 11.24
2032 4.59 19-3/8" 34-1/8" 8.18 4.59 12.53
2036 5.13 19-3/8" 38-1/8" 9.24 5.13 13.82
2040 5.67 19-3/8" 42-1/8" 10.29 5.67 15.12
2044 6.21 19-3/8" 46-1/8" 11.35 6.21 16.41
2048 6.74 19-3/8" 50-1/8" 12.40 6.74 17.70
2416 2.94 23-3/8" 18-1/8" 4.79 2.94 8.63
2420 3.59 23-3/8" 22-1/8" 6.07 3.59 10.15
2424 4.24 23-3/8" 26-1/8" 7.35 4.24 11.66
2428 4.89 23-3/8" 30-1/8" 8.63 4.89 13.18
2432 5.54 23-3/8" 34-1/8" 9.90 5.54 14.69
2436 6.19 23-3/8" 38-1/8" 11.18 6.19 16.20
2440 6.84 23-3/8" 42-1/8" 12.46 6.84 17.72
2444 7.49 23-3/8" 46-1/8" 13.74 7.49 19.23
2448 8.14 23-3/8" 50-1/8" 15.01 8.14 20.74
2816 3.45 27-3/8" 18-1/8" 5.63 3.45 9.90
2820 4.21 27-3/8" 22-1/8" 7.13 4.21 11.64
2824 4.97 27-3/8" 26-1/8" 8.63 4.97 13.37
2828 5.73 27-3/8" 30-1/8" 10.13 5.73 15.11
2832 6.49 27-3/8" 34-1/8" 11.63 6.49 16.85
2836 7.25 27-3/8" 38-1/8" 13.13 7.25 18.58
2840 8.01 27-3/8" 42-1/8" 14.63 8.01 20.32
2844 8.77 27-3/8" 46-1/8" 16.13 8.77 22.05
2848 9.53 27-3/8" 50-1/8" 17.63 9.53 23.79
3216 3.95 31-3/8" 18-1/8" 6.46 3.95 11.17
3220 4.82 31-3/8" 22-1/8" 8.18 4.82 13.13
3224 5.69 31-3/8" 26-1/8" 9.90 5.69 15.09
3228 6.56 31-3/8" 30-1/8" 11.63 6.56 17.04
3232 7.44 31-3/8" 34-1/8" 13.35 7.44 19.00
3236 8.31 31-3/8" 38-1/8" 15.07 8.31 20.96
3240 9.18 31-3/8" 42-1/8" 16.79 9.18 22.92
3244 10.05 31-3/8" 46-1/8" 18.51 10.05 24.88
3248 10.92 31-3/8" 50-1/8" 20.24 10.92 26.84
C l e a r O p e n i n G d i m e n s i O n s
Notes For doUBLe HUNG WiNdoWs:➢ Shaded units meet most national building codes for emergency escape and rescue requirements.
Product#
sq. Ft. Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft. Vent
sq. Ft. of Unit Frame dim.
Width Height
Traditional Double Hungs (continued)
4028 8.05 42-1/4" 27-7/16" 14.63 8.05 20.36
4030 8.64 42-1/4" 29-7/16" 15.71 8.64 21.63
4032 9.22 42-1/4" 31-7/16" 16.79 9.22 22.89
4034 9.81 42-1/4" 33-7/16" 17.88 9.81 24.15
4036 10.40 42-1/4" 35-7/16" 18.96 10.40 25.42
1624/36 2.97 18-1/4" 23-7/16" 6.04 2.97 10.22
2024/36 3.62 22-1/4" 23-7/16" 7.65 3.62 12.12
2424/36 4.27 26-1/4" 23-7/16" 9.26 4.27 14.02
2824/36 4.92 30-1/4" 23-7/16" 10.88 4.92 15.92
3224/36 5.57 34-1/4" 23-7/16" 12.49 5.57 17.82
3624/36 6.23 38-1/4" 23-7/16" 14.10 6.23 19.72
4024/36 6.88 42-1/4" 23-7/16" 15.71 6.88 21.63
4024 6.88 42-1/4" 23-7/16" 12.46 6.88 17.83
4026 7.46 42-1/4" 25-7/16" 13.54 7.46 19.10
10�www.kolbe-kolbe.com
Product#
sq. Ft. Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft.
Vent
sq. Ft. of Unit Frame dim.
Width Height
Triple Sliders
163232 4.13 17-7/16" 34-1/8" 13.02 6.78 19.27
163240 5.10 17-7/16" 42-1/8" 16.39 8.37 23.24
163244 5.59 17-7/16" 46-1/8" 18.07 9.17 25.23
163248 6.07 17-7/16" 50-1/8" 19.75 9.96 27.22
204032 5.08 21-7/16" 34-1/8" 16.47 8.68 23.58
204040 6.27 21-7/16" 42-1/8" 20.72 10.71 28.44
204044 6.87 21-7/16" 46-1/8" 22.84 11.73 30.88
204048 7.46 21-7/16" 50-1/8" 24.97 12.75 33.31
204832 5.08 21-7/16" 34-1/8" 18.19 9.67 25.74
204840 6.27 21-7/16" 42-1/8" 22.89 11.94 31.05
204844 6.87 21-7/16" 46-1/8" 25.23 13.07 33.70
204848 7.46 21-7/16" 50-1/8" 27.58 14.21 36.35
244832 6.03 25-7/16" 34-1/8" 19.91 10.58 27.90
244840 7.44 25-7/16" 42-1/8" 25.05 13.05 33.65
244844 8.15 25-7/16" 46-1/8" 27.62 14.29 36.52
244848 8.85 25-7/16" 50-1/8" 30.19 15.53 39.40
C l e a r O p e n i n G d i m e n s i O n s
Notes For sLider WiNdoWs:➢ Shaded units meet most national building codes for emergency escape and rescue requirements.
Product#
sq. Ft. Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft. Vent
sq. Ft. of Unit Frame dim
Width Height
Viewport Sliding Patio Doors
6068 18.09 32-7/8" 79-1/4" 34.17 18.09 44.40
Product#
sq. Ft. Clear opg.
Clear openingsq. Ft. d.L.o.
sq. Ft. Vent
sq. Ft. of Unit Frame dim
Width Height
Garden-Aire Sliding Patio Doors
2968 – – – 12.46 – 18.61
3368 – – – 15.55 – 22.04
3668 – – – 17.09 – 28.91
4368 – – – 21.71 – 28.91
2980 – – – 15.16 – 22.22
3380 – – – 18.91 – 26.32
3680 – – – 20.78 – 28.37
4380 – – – 26.41 – 34.52
5068 12.01 22" 78-5/8" 24.92 12.01 34.35
6068 15.29 28" 78-5/8" 31.09 15.29 41.22
6668 16.93 31" 78-5/8" 34.17 16.93 44.65
8068 21.84 40" 78-5/8" 43.42 21.84 54.96
5080 14.46 22" 94-5/8" 30.31 14.46 41.02
6080 18.40 28" 94-5/8" 37.81 18.40 49.22
6680 20.37 31" 94-5/8" 41.56 20.37 53.32
8080 26.28 40" 94-5/8" 52.81 26.28 65.63
7968 12.01 22" 78-5/8" 37.39 12.01 52.95
9368 15.29 28" 78-5/8" 46.64 15.29 63.26
10068 16.93 31" 78-5/8" 51.26 16.93 68.41
12368 21.84 40" 78-5/8" 65.14 21.84 83.87
7980 14.46 22" 94-5/8" 45.47 14.46 63.23
9380 18.40 28" 94-5/8" 56.72 18.40 75.54
10080 20.37 31" 94-5/8" 62.34 20.37 81.69
12380 26.28 40" 94-5/8" 79.22 26.28 100.15
2866 – – – 10.72 – 17.76
3266 – – – 14.77 – 21.09
4266 – – – 20.73 – 27.76
41166 11.37 21-1/2" 76-1/8" 23.59 11.37 32.75
51166 14.54 27-1/2" 76-1/8" 29.54 14.54 39.41
71166 20.88 39-1/2" 76-1/8" 41.46 20.88 52.74
7766 11.37 21-1/2" 76-1/8" 35.38 11.37 50.52
9166 14.54 27-1/2" 76-1/8" 44.32 14.54 60.51
12166 20.88 39-1/2" 76-1/8" 62.19 20.88 80.49
Garden-Aire Sliding Patio Doors, remodeling sizes
10� ClassiC series
C l e a r O p e n i n G d i m e n s i O n s
Product#
sq. Ft. Clear opg.
Clear opg. Width Clear
opg. Ht.
sq. Ft.
d.L.o.
sq. Ft.
Vent
sq. Ft. of Unit
Frame dim.
1 open
2 open
1 open
2 open
Inswing Entrance Doors - 1-wide
2068 11.67 – 21-1/8" – 79-9/16" 6.93 12.71 14.72
2668 14.99 – 27-1/8" – 79-9/16" 9.76 16.02 18.17
2868 16.09 – 29-1/8" – 79-9/16" 10.70 17.13 19.32
3068 18.30 – 33-1/8" – 79-9/16" 12.59 19.34 21.61
2070 12.26 – 21-1/8" – 83-9/16" 7.33 13.35 15.43
2670 15.74 – 27-1/8" – 83-9/16" 10.33 16.83 19.05
2870 16.90 – 29-1/8" – 83-9/16" 11.33 17.99 20.25
3070 19.22 – 33-1/8" – 83-9/16" 13.33 20.31 22.66
2080 14.02 – 21-1/8" – 95-9/16" 8.56 15.26 17.57
2680 18.00 – 27-1/8" – 95-9/16" 12.05 19.25 21.68
2880 19.33 – 29-1/8" – 95-9/16" 13.22 20.57 23.05
3080 21.98 – 33-1/8" – 95-9/16" 15.55 23.23 25.79
Inswing Entrance Doors - �-wide (stationary/active)
4068 11.67 – 21-1/8" – 79-9/16" 13.85 12.68 28.83
5068 14.99 – 27-1/8" – 79-9/16" 19.51 16.00 35.72
5468 16.09 – 29-1/8" – 79-9/16" 21.40 17.10 38.02
6068 18.30 – 33-1/8" – 79-9/16" 25.17 19.31 42.62
4070 12.26 – 21-1/8" – 83-9/16" 14.67 13.32 30.22
5070 15.74 – 27-1/8" – 83-9/16" 20.66 16.80 37.45
5470 16.90 – 29-1/8" – 83-9/16" 22.66 17.96 39.86
6070 19.22 – 33-1/8" – 83-9/16" 26.65 20.28 44.68
4080 14.02 – 21-1/8" – 95-9/16" 17.12 15.23 34.41
5080 18.00 – 27-1/8" – 95-9/16" 24.11 19.21 42.63
5480 19.33 – 29-1/8" – 95-9/16" 26.44 20.54 45.38
6080 21.98 – 33-1/8" – 96-9/16" 31.10 23.20 50.86
Inswing Entrance Doors - French
4068 11.67 22.65 21-1/8" 41" 79-9/16" 13.85 26.28 28.83
5068 14.99 29.28 27-1/8" 53" 79-9/16" 19.51 32.91 35.72
5468 16.09 31.49 29-1/8" 57" 79-9/16" 21.40 35.12 38.02
6068 18.30 35.91 33-1/8" 65" 79-9/16" 25.17 39.54 42.62
4070 12.26 23.79 21-1/8" 41" 83-9/16" 14.67 27.60 30.22
5070 15.74 30.76 27-1/8" 53" 83-9/16" 20.66 34.56 37.45
5470 16.90 33.08 29-1/8" 57" 83-9/16" 22.66 36.89 39.86
6070 19.22 37.72 33-1/8" 65" 83-9/16" 26.65 41.53 44.68
4080 14.02 27.21 21-1/8" 41" 95-9/16" 17.12 31.56 34.41
5080 18.00 35.17 27-1/8" 53" 95-9/16" 24.11 39.53 42.63
5480 19.33 37.83 29-1/8" 57" 95-9/16" 26.44 42.18 45.38
6080 21.98 43.14 33-1/8" 65" 95-9/16" 31.10 47.49 50.86
Notes For iNsWiNG eNtraNCe doors:➢ For units with optional oak or handicap sills, add 5/8" to the clear opening heights.➢ One or both sash open to 90º.
Product#
sq. Ft. Clear opg.
Clear opg. Width Clear
opg. Height
sq. Ft.
d.L.o.
sq. Ft.
Vent
sq. Ft. of Unit
Frame dim.
1 open
2 open
1 open
2 open
Inswing Patio Doors - 1-wide
2666 13.65 – 25-3/4" – 76-11/32" 8.68 14.65 16.70
3066 16.83 – 31-3/4" – 76-11/32" 11.37 17.83 20.01
2680 16.53 – 25-3/4" – 92-7/16" 10.83 17.73 20.08
3080 20.38 – 31-3/4" 92-7/16" 14.20 21.58 24.06
Inswing Patio Doors - �-wide (stationary/active)
41166 13.65 – 25-3/4" – 76-11/32" 17.35 14.62 32.81
51166 16.83 – 31-3/4" – 76-11/32" 22.74 17.80 39.44
41180 16.53 – 25-3/4" – 92-7/16" 21.67 17.70 39.46
51180 20.38 – 31-3/4" – 92-7/16" 28.40 21.55 47.42
Inswing Patio Doors - French
41166 13.65 26.64 25-3/4" 50-1/4" 76-11/32" 17.35 30.12 32.81
51166 16.83 33.00 31-3/4" 62-1/4" 76-11/32" 22.74 36.48 39.44
41180 16.53 32.26 25-3/4" 50-1/4" 92-7/16" 21.67 36.47 39.46
51180 20.38 39.96 31-3/4" 62-1/4" 92-7/16" 28.40 44.17 47.42
Inswing Patio Doors - �-wide (stationary/active/stationary)
7566 13.65 – 25-3/4" – 76-11/32" 26.03 14.62 48.93
81166 16.83 – 31-3/4" – 76-11/32" 34.11 17.80 58.87
7580 16.53 – 25-3/4" – 92-7/16" 32.50 17.70 58.83
81180 20.38 – 31-3/4" – 92-7/16" 42.60 21.55 70.78
Notes For iNsWiNG Patio doors:➢ For units with handicap sills, add 5/8" to the clear opening heights.➢ One or both sash open to 90º
107www.kolbe-kolbe.com
C l e a r O p e n i n G d i m e n s i O n s
Product#
sq. Ft. Clear opg.
Clear opg. WidthClear
opg. Ht.
sq. Ft.
d.L.o.
sq. Ft.
Vent
sq. Ft. of Unit Frame dim.
1 open
2 open
1 open
2 open
Outswing Doors - patio sizes, 1-wide
2666 13.60 – 25-27/32" – 75-25/32" 8.68 14.59 17.33
3066 16.76 – 31-27/32" – 75-25/32" 11.37 17.74 20.65
2680 16.49 – 25-27/32" – 91-7/8" 10.83 17.69 20.83
3080 20.32 – 31-27/32" – 91-7/8" 14.19 21.51 24.82
Outswing Doors - patio sizes, �-wide (stationary/active)
41166 13.60 – 25-27/32" – 75-25/32" 17.35 14.57 33.52
51166 16.76 – 31-27/32" – 75-25/32" 22.74 17.73 40.16
41180 16.49 – 25-27/32" – 91-7/8" 21.66 17.67 40.30
51180 20.32 – 31-27/32" – 91-7/8" 28.39 21.49 48.27
Outswing Doors - patio sizes, French
41166 13.60 27.13 25-27/32" 51-9/16" 75-25/32" 17.35 30.00 33.52
51166 16.76 33.45 31-27/32" 63-9/16" 75-25/32" 22.74 36.31 40.16
41180 16.49 32.90 25-27/32" 51-9/16" 91-7/8" 21.66 36.37 40.30
51180 20.32 40.55 31-27/32" 63-9/16" 91-7/8" 28.39 44.02 48.27
Outswing Doors - patio sizes, �-wide (stationary/active/stationary)
7566 13.60 – 25-27/32" – 75-25/32" 26.03 14.57 49.97
81166 16.76 – 31-27/32" – 75-25/32" 34.11 17.73 59.93
7580 16.49 – 25-27/32" – 91-7/8" 32.49 17.66 60.07
81180 20.32 – 31-27/32" – 91-7/8" 42.58 21.49 72.04
Notes For oUtsWiNG Patio doors:➢ For units with handicap sills, add 1-1/8" to the clear opening heights.➢ One or both sash open to 90º.
108 ClassiC series
Product#
sq. Ft. Clear opg.
Clear opg. WidthClear opg. Ht.
sq. Ft.
d.L.o.
sq. Ft.
Vent
sq. Ft. of Unit
Frame dim.
1 open
2 open
1 open 2 open
Outswing Entrance Doors - 1-wide
2068 11.64 – 21-7/32" – 79" 6.92 12.67 15.37
2668 14.93 – 27-7/32" – 79" 9.75 15.96 18.82
2868 16.03 – 29-7/32" – 79" 10.69 17.06 19.97
3068 18.22 – 33-7/32" – 79" 12.57 19.25 22.28
2070 12.23 – 21-7/32" – 83" 7.33 13.31 16.11
2670 15.69 – 27-7/32" – 83" 10.32 16.77 19.73
2870 16.84 – 29-7/32" – 83" 11.32 17.92 20.94
3070 19.15 – 33-7/32" – 83" 13.32 20.23 23.35
2080 14.00 – 21-7/32" – 95" 8.55 15.24 18.34
2680 17.96 – 27-7/32" – 95" 12.05 19.19 22.46
2880 19.28 – 29-7/32" – 95" 13.21 20.51 23.83
3080 21.92 – 33-7/32" – 95" 15.54 23.15 26.58
Outswing Entrance Doors - �-wide (stationary/active)
4068 11.64 – 21-7/32" – 79" 13.84 12.65 29.56
5068 14.93 – 27-7/32" – 79" 19.49 15.94 36.46
5468 16.03 – 29-7/32" – 79" 21.38 17.04 38.76
6068 18.22 – 33-7/32" – 79" 25.15 19.24 43.36
4070 12.23 – 21-7/32" – 83" 14.66 13.29 30.98
5070 15.69 – 27-7/32" – 83" 20.64 16.75 38.22
5470 16.84 – 29-7/32" – 83" 22.64 17.90 40.63
6070 19.15 – 33-7/32" – 83" 26.63 20.21 45.46
4080 14.00 – 21-7/32" – 95" 17.10 15.21 35.26
5080 17.96 – 27-7/32" – 95" 24.09 19.17 43.50
5480 19.28 – 29-7/32" – 95" 26.42 20.49 46.25
6080 21.91 – 33-7/32" – 95" 31.08 23.13 51.74
Outswing Entrance Doors - French
4068 11.64 23.21 21-7/32" 42-5/16" 79" 13.84 26.20 29.56
5068 14.93 29.80 27-7/32" 54-5/16" 79" 19.49 32.78 36.46
5468 16.03 31.99 29-7/32" 58-5/16" 79" 21.38 34.97 38.76
6068 18.22 36.38 33-7/32" 66-5/16" 79" 25.15 39.36 43.36
4070 12.23 24.39 21-7/32" 42-5/16" 83" 14.66 27.52 30.98
5070 15.69 31.30 27-7/32" 54-5/16" 83" 20.64 34.44 38.22
5470 16.84 33.61 29-7/32" 58-5/16" 83" 22.64 36.74 40.63
6070 19.15 38.22 33-7/32" 66-5/16" 83" 26.63 41.36 45.46
4080 14.00 27.91 21-7/32" 42-5/16" 95" 17.10 31.50 35.26
5080 17.96 35.83 27-7/32" 54-5/16" 95" 24.09 39.42 43.50
5480 19.28 38.47 29-7/32" 58-5/16" 95" 26.42 42.06 46.25
6080 21.91 43.75 33-7/32" 66-5/16" 95" 31.08 47.34 51.74
C l e a r O p e n i n G d i m e n s i O n s
Notes For oUtsWiNG eNtraNCe doors:➢ For units with handicap sills, add 1-1/8" to the clear opening heights.➢ One or both sash open to 90º.
Note:➢ For the most up to date data, please visit the Kolbe website at www.kolbe-kolbe.com.
109www.kolbe-kolbe.com
Most of the products and glazing options listed below are NFRC listed. The values are calculated using the NFRC approved WINDOW and THERM computer programs. PDL glazing options generally have the same U-factor as one-lite. SS spacer means stainless steel Thermo-Edge spacer. Kolbe’s standard argon-filled insulating glass has a LoE coating on #2 glass surface. It has the desirable combination of visual clarity, good U value, with one of the lowest Solar Heat Gain Coefficients (SHGC) available in clear insulating glass. This great combined performance is suitable nationwide. Air values are given for when high altitude breather tubes are used. Tubes may be used when units are to be installed in or shipped through high altitude areas. It is your responsibility to know what units are being used. Operating awning unit values are similar to those of operating casements, therefore those values are not listed. Additional values are available upon request.
enerGy perFormanCe Data notes
U/R Total – The U factor and R value of a total unit. A small U factor means less heat escapes during winter weather. Units are Btu/(hr•ft2•ºF) R = 1/U Thus, a large R value means less heat escapes during winter weather. SHGC Total – Solar Heat Gain Coefficient Total is a unitless number representing the ratio of radiant solar energy passing through/ incident solar radiation. A small SHGC is desirable during summer. This includes the effect of frame and dividers, which have SHGC of almost zero. Shading Coefficient = SHGC / 0.86 cog – Center-of-glass is the central glazed portion of a window or door which you can see through, that is more than 2.5" from sightline. Total – Total values include the effects of frames, dividers, edge-of-glass, and cog.Glass Temperature – cog roomside glass surface, assumes winter night 0ºF exterior air, 15mph wind, and 70ºF roomside air. A higher glass temperature means better glass insulating value and condensation is less likely. Roomside edge-of-glass is usually cooler than cog. Relative Humidity – Assumes same winter conditions. 70º roomside at this relative humidity begins to form condensation on cog room side glass surface. Condensation will form more easily on cooler roomside edge-of-glass than on cog. Vt – Visible Transmittance of the total fenestration product system is the transmittance across the visible portion of the solar spectrum where sensitivity to each wavelength is weighted by the eyes response. Vt is expressed as a dimensionless number from 0 (completely opaque) to 1.0 (completely clear). This value is influenced by the glass selection and by the ratio of glazing and frame area. Vtc high number (Ø.65) means nearly clear view, and low Vt total number means tinted view. Vtc cog – Visual transmittance is a unitless number representing the ratio of visible light passing through glass/incident visible light. A high number (>.65) means nearly clear view and a low Vt number means tinted view. Tuv cog – A unitless number representing the ratio of ultraviolet radiation (wavelength 0.30-0.38 micron) passing through glass/ same incident ultraviolet radiation. A low number is generally desirable. Tdw-K cog – A unitless number representing the ratio of weighted ultraviolet and visible radiation (.30-.50 microns) passing through glass/same incident radiation. A low number is generally desirable. For some fabrics and colors this is a more accurate measure of fade potential than Tuv. Tdw-K uses Krochmann formula. Tdw-ISO cog – Similar to Tdw-K, Tdw-ISO uses International Standards Organization formula.
Energy Star – Requires NFRC values below: The following 3 symbols indicate why a product doesn’t have an Energy Star Rating: Northern U ≤ .35 & SHGC = Any North Central U ≤ .40 & SHGC ≤ .55 @ Values don’t qualify South Central U ≤ .40 & SHGC ≤ .40 # Not NFRC listed Southern U ≤ .65 & SHGC ≤ .40 * NFRC listing doesn’t include SHGC yet
Product Line descriptionGlazing Variations
U/r total
sHGC total
Vt total
Ucog
sHGCcog
Vtccog
Glass temp
°F, cog
r.H. %,
cog
tuv cog
tdw-Kcog
tdw-iso cog
Operating Casement
Clad, Onelite, 7/8" HºK air, SS spcr .37/2.70 0.26 0.48 0.30 0.37 0.70 52.9 57.5 0.14 0.31 0.53 NC, SC, S
PDL & Bars-in-Glass < 1" .37/2.70 0.24 0.43 0.30 0.37 0.70 52.9 57.5 0.14 0.31 0.53 NC, SC, S
PDL & Bars-in-Glass ≥ 1" .37/2.70 0.22 0.39 0.30 0.37 0.70 52.9 57.5 0.14 0.31 0.53 NC, SC, S
Clad, Onelite, 7/8" HºK arg, SS spcr .34/2.94 0.26 0.48 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53 N, NC, SC, S, A
PDL & Bars-in-Glass < 1" .34/2.94 0.24 0.43 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53 N, NC, SC, S, A
PDL & Bars-in-Glass ≥ 1" .34/2.94 0.22 0.39 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53 N, NC, SC, S, A
Clad, Onelite, 7/8" LoE 240 arg, SS spcr .34/2.94 0.18 0.27 0.26 0.25 0.40 55.0 60.3 0.16 0.24 0.35 N, NC, SC, S, A
e n e r G y p e r F O r m a n C e d ata
EnErgy Star
N, NC, sC, sEnErgy Star
Canadaa, B, C, d
110 ClassiC series
e n e r G y p e r F O r m a n C e d ata
Product Line descriptionGlazing Variations
U/r total
sHGC total
Vt total
Ucog
sHGCcog
Vtccog
Glass temp
°F, cog
r.H. %,
cog
tuv cog
tdw-K
cog
tdw-iso cog
Fixed Casement Sash Set
Clad, Onelite, 7/8" HºK air, SS spcr .35/2.85 0.30 0.56 0.30 0.37 0.70 52.9 57.5 0.14 0.31 0.53 N, NC, SC, S, A
PDL & Bars-in-Glass < 1" .35/2.85 0.27 0.50 0.30 0.37 0.70 52.9 57.5 0.14 0.31 0.53 N, NC, SC, S, A
PDL & Bars-in-Glass ≥ 1" .35/2.85 0.24 0.44 0.30 0.37 0.70 52.9 57.5 0.14 0.31 0.53 N, NC, SC, S, A
Clad, Onelite, 7/8" HºK arg, SS spcr .31/3.22 0.30 0.56 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53N, NC, SC, S,
A, B
PDL & Bars-in-Glass < 1" .31/3.22 0.27 0.50 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53N, NC, SC, S,
A, B
PDL & Bars-in-Glass ≥ 1" .31/3.22 0.24 0.44 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53N, NC, SC, S,
A, B
Clad, Onelite, 7/8" LoE 240 arg, SS spcr .32/3.12 0.20 0.32 0.26 0.25 0.40 55.0 60.3 0.16 0.24 0.35N, NC, SC, S,
A, B
Traditional Double Hung
Clad, Onelite, 9/16" HºK air, SS spcr .36/2.77 0.27 0.50 0.32 0.37 0.71 52.1 51.5 0.15 0.32 0.53 NC, SC, S
PDL & Bars-in-Glass < 1" .38/2.63 0.25 0.45 0.32 0.37 0.71 52.1 51.5 0.15 0.32 0.53 NC, SC, S
PDL & Bars-in-Glass ≥ 1" .38/2.63 0.22 0.39 0.32 0.37 0.71 52.1 51.5 0.15 0.32 0.53 NC, SC, S
Clad, Onelite, 9/16" HºK arg, SS spcr .32/3.12 0.27 0.50 0.26 0.37 0.71 55.3 58.6 0.15 0.32 0.53 N, NC, SC, S, A
PDL & Bars-in-Glass < 1" .34/2.94 0.24 0.45 0.26 0.37 0.71 55.3 58.6 0.15 0.32 0.53 N, NC, SC, S, A
PDL & Bars-in-Glass ≥ 1" .34/2.94 0.22 0.39 0.26 0.37 0.71 55.3 58.6 0.15 0.32 0.53 N, NC, SC, S, A
Clad, Onelite, 9/16" HºK arg, SS, Combo .25/4.00 0.27 0.46 0.20 0.37 0.65 58.6 66.6 0.13 0.29 0.48N, NC, SC, S,
A, B, C, D
Traditional Slider
Clad, Onelite, 9/16" HºK air, Al spcr .43/2.32 0.27 0.47 0.32 0.37 0.71 52.1 51.5 0.15 0.32 0.53 S
PDL & Bars-in-Glass < 1" .44/2.32 0.25 0.42 0.32 0.37 0.71 52.1 51.5 0.15 0.32 0.53 S
PDL & Bars-in-Glass ≥ 1" .44/2.27 0.22 0.37 0.32 0.37 0.71 52.1 51.1 0.15 0.32 0.53 S
Clad, Onelite, 9/16" HºK arg, Al spcr .39/2.56 0.27 0.47 0.26 0.37 0.71 55.3 58.6 0.15 0.32 0.53 NC, SC, S
PDL & Bars-in-Glass < 1" .40/2.50 0.25 0.42 0.26 0.37 0.71 55.3 58.6 0.15 0.32 0.53 NC, SC, S
PDL & Bars-in-Glass ≥ 1" .40/2.50 0.22 0.37 0.26 0.37 0.71 55.3 58.6 0.15 0.32 0.53 NC, SC, S
Clad, Onelite, 9/16" HºK arg, SS spcr .36/2.78 0.27 0.47 0.26 0.37 0.71 55.3 58.6 0.15 0.32 0.53 NC, SC, S
PDL & Bars-in-Glass < 1" .37/2.70 0.25 0.42 0.26 0.37 0.71 55.3 58.6 0.15 0.32 0.53 NC, SC, S
PDL & Bars-in-Glass ≥ 1" .37/2.70 0.22 0.37 0.26 0.37 0.71 55.3 58.6 0.15 0.32 0.53 NC, SC, S
Clad, Onelite, 9/16" HºK arg, SS, Combo .27/3.70 0.28 0.42 0.20 0.37 0.65 58.6 66.6 0.13 0.29 0.48 N, NC, SC S
Viewport Sliding Patio Door
Clad, Onelite, 7/8" HºK air, SS spcr .35/2.85 0.28 0.53 0.32 0.37 0.70 52.9 57.5 0.14 0.31 0.52 N, NC, SC, S
PDL & Bars-in-Glass < 1" .35/2.85 0.25 0.46 0.32 0.37 0.70 52.9 57.5 0.14 0.31 0.52 N, NC, SC, S
PDL & Bars-in-Glass ≥ 1" .35/2.85 0.22 0.40 0.32 0.37 0.70 52.9 57.5 0.14 0.31 0.52 N, NC, SC, S
Clad, Onelite, 7/8" HºK arg, SS spcr .31/3.22 0.28 0.53 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.52 N, NC, SC, S
PDL & Bars-in-Glass < 1" .31/3.22 0.25 0.46 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.52 N, NC, SC, S
PDL & Bars-in-Glass ≥ 1" .31/3.22 0.22 0.40 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.52 N, NC, SC, S
Garden-Aire Sliding Patio Door
Clad, Onelite, 7/8" HºK air, SS spcr .34/2.94 0.29 0.53 0.30 0.36 0.70 52.9 57.5 0.14 0.31 0.52 N, NC, SC, S
PDL & Bars-in-Glass < 1" .34/2.94 0.25 0.47 0.30 0.36 0.70 52.9 57.5 0.14 0.31 0.52 N, NC, SC, S
PDL & Bars-in-Glass ≥ 1" .34/2.94 0.22 0.40 0.30 0.36 0.70 52.9 57.5 0.14 0.31 0.52 N, NC, SC, S
EnErgy Star
N, NC, sC, sEnErgy Star
Canadaa, B, C, d
111www.kolbe-kolbe.com
e n e r G y p e r F O r m a n C e d atae n e r G y p e r F O r m a n C e d ata
Product Line descriptionGlazing Variations
U/r total
sHGC total
Vt total
Ucog
sHGCcog
Vtccog
Glass temp
°F, cog
r.H. %,
cog
tuv cog
tdw-Kcog
tdw-iso cog
Garden-Aire Sliding Patio Door (continued)
Clad, Onelite, 7/8" HºK arg, SS spcr .31/3.22 0.29 0.53 0.26 0.36 0.70 55.4 62.9 0.14 0.31 0.52 N, NC, SC, S
PDL & Bars-in-Glass < 1" .31/3.22 0.25 0.47 0.26 0.36 0.70 55.4 62.9 0.14 0.31 0.52 N, NC, SC, S
PDL & Bars-in-Glass ≥ 1" .31/3.22 0.22 0.40 0.26 0.36 0.70 55.4 62.9 0.14 0.31 0.52 N, NC, SC, S
Inswing Patio Door & Inswing Entrance Door
Clad, Onelite, 7/8" HºK air, SS spcr .34/2.94 0.22 0.41 0.30 0.37 0.70 52.9 57.5 0.14 0.31 0.53 N, NC, SC, S
PDL & Bars-in-Glass < 1" .34/2.94 0.20 0.35 0.30 0.37 0.70 52.9 57.5 0.14 0.31 0.53 N, NC, SC, S
PDL & Bars-in-Glass ≥ 1" .34/2.94 0.17 0.30 0.30 0.37 0.70 52.9 57.5 0.14 0.31 0.53 N, NC, SC, S
Clad, Onelite, 7/8" HºK arg, SS spcr .32/3.12 0.22 0.41 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53 N, NC, SC, S
PDL & Bars-in-Glass < 1" .32/3.12 0.19 0.35 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53 N, NC, SC, S
PDL & Bars-in-Glass ≥ 1" .32/3.12 0.17 0.30 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53 N, NC, SC, S
Clad, Onelite, 7/8" LoE 240 arg, SS spcr .32/3.12 0.15 0.24 0.26 0.25 0.40 55.0 60.3 0.16 0.24 0.35 N, NC, SC, S
Outswing Entrance Door
Clad, Onelite, 7/8" HºK arg, SS spcr .35/2.85 0.24 0.39 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53 N, NC, SC, S
PDL & Bars-in-Glass < 1" .35/2.85 0.22 0.35 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53 N, NC, SC, S
PDL & Bars-in-Glass ≥ 1" .35/2.85 0.20 0.31 0.26 0.37 0.70 55.4 62.9 0.14 0.31 0.53 N, NC, SC, S
Note:Air, water and structural data is updated monthly and is available after registration & sign-in at www.kolbe-kolbe.com.For Canadian EnErgy Star ratings, visit the Kolbe website at www.kolbe-kolbe.com and click on Energy & Performance.
EnErgy Star
N, NC, sC, sEnErgy Star
Canadaa, B, C, d
1323 S. 11th Avenue Wausau, WI 54401-5998715.842.5666
www.kolbe -kolbe.com
© 2008 Kolbe & Kolbe Millwork Co., Inc.Kolbe & Kolbe Millwork Co., Inc. reserves the right to change specifications without notice.
Photography used may not represent current Kolbe product features and options.5131560-15M-0408-RP