SOUND ABSORBENT .. INSULATION WITH

MYLAR FACING

QUICK ACTION SCREWS FOR EASY ACCESS

ENAMELED STEEL PANELS ;If

-IU - --

... ~I "Z'''SE,CTII1N EDGES :.II1IIW~~"p •• 'T

WESTERBEKE'S SOUND ENCLOSURE/SPECIFICATIONS & INSTRUCTIONS INSTRUCTIONS

1. Plywood base, generator set bolts and skirt are in place as re- SOUND GUARD AIR FLOW DIAGRAM AND DIMENSIONS

• ( ceived . DIMENSIONS IN INCHES

GENERATOR A B C 0 E G H 2. Hoist the generator set enough so that two men can 11ft the WMO 3 Wk 3 32 3 14'" 34% 20Y. 23% 22'/. 140/, lY.

plywood base and enter the bolts into corresponding holes in WMD 4 18 31f2 34 31f.! 18 36 23 25 25 18 111, generator set raits . Spin nuts finger tight . Assembly may then be WMD 7.7 18 3'12 42 3'h 18 44 23 26 25 18 11/, lowered into position and bolting completed . WMO 11 & 12.5 191f2 31f.! 48'h 31f2 19'h 51 24% 2714 27 193/. 1'1e

3. The generator set and base may then be bolted to the sub-base WTA I5. 20&25 21 5 54 5 21 56 26 30 28 20 IV, through holes in corner 01 the plywood. WTF 32 21 5 65'12 5 21 673/. 30 33 32 20 11/,

4 . To assemble frame, follow the drawing . Be sure that open holes NoTE: For dimensions 01 additional SOUNDIGUARO units contact your Westerbeke representative . are opposite guide pins and that riveted screw receptacles are B--l-- C I 0- r-- G ------i' opposite screws. I I ___ --'==eo::===i=*1 1 'I. ~

5. On units which require a fan follow this procedure: 'r ---' A. Remove 4 short screws which hold fresh water pump pulley T ..

hub. B. Reassemble hub with fan . fan spacer, and 4 cap screws lur~ A • ~,.,/.,

nished. Tighten securely. ~ ,/ 6. Holes for fuel lines. battery cables, remote panel cable , and power

lines are to be cut in the lower skirt by the installer. These holes should be cut to minimum usable size in order to minimize the escape of sound.

7. Make a final check to be sure fan has clearance in its opening . that the fresh air duct from intake plenum to engine air intake is clamped in place. and that there is a light fit of air plenum against the end of the generator to prevent re-ci rculation of air.

8. If you plan to order SOUND GUARD . order the generator sel with remote panel and cable extension .

CAUTION: With the air discharge end panel removed , the fan is exposed and unprotected . 00 NOT remove air discharge end panel without first stopping engine.

SIMPLE OUICK ACTION LOCK AND RELE ASE FASTENINGS

EASY TO ASSE MBLE CORNER DETAIL

BATTERY CONN ECTIONS

WATER INJECTED RUBBER EXHAUST HOSE TO WATER LIFT TYPE MUFFLER

FLEX DUCT FOR COMBUSTION

CALL YOUR WESTERBEKE REPRESENTATIVE

MR 11 /83 PRINTED IN u.s A 7500

-'-,..A

\'IJL ~ .. ~~~~ AIR INTAKE

H

DISCHARGE FAN

NOTE: FAN ASSEMBLY IS REOUIREO ON CERTAIN MODELS

INTAKE FOR SEA WATER

\

(

---

:-i IJIU ...... , ~e

~~~ '""':::. :~~~~~g~i~~~:~;

INSULATION WITH MYLAR FACING

ENAMELED STEEL PANELS ill ALUMINUM HANDLES

An easy to assemble sound enclosure to fit all Westerbeke generators.

ALUMINUM EXTRUSION FRAME WITH DIE CAST CORNERS FOR ACCURACY

Experience the sound of si lence with Westerbeke's all new SOUND GUARD. A sound enclosure that essential ly reduces al l

generator noise and provides its own air cooling and air exhaust

SOUND GUARD is a rigid , attractive, easy to clean enclosure that cons ists o f five enameled stee l panels fitted to an aluminum

frame and skirt and a wood base.

SOUND GUARD is lightweight , durable, and requires no maintenance and it can be assembled easi ly in close quarters.

The turn of two " Quick Action" screws wi ll remove each panel for ro utine inspection or serv icing and should major repairs be reo

quired the entire enclosure can be disassembled in a few minutes; no tools are needed. Al l the generator service lines are installed

thru the aluminum skirt. Westerbeke provides the necessary fittings and connecting hose for water, exhaust , fuel , battery ,

and power l ines.

SOUND GUARD is carefu ll y pre·packaged with the skirt and base assembled to assure safe arrival and speedy assembly. Instructions are prov ided on the back o f thi s sheet.

J. H. WESTERBEKE CORP. AVON INDUSTRIAL PARK. AVON. MASS. 02322· (6 17) 588· 7700

CA BLE: WESTCORP, AVON · TELEX: 92·4444

WESTERBEKE'S SOUND ENCLOSURE/SPECIFICATIONS & INSTRUCTIONS

C II: ca: :J

"

INSTRUCTIONS 1. Plywood base, generator set bolts and skirt are in place as re-

ceived. 2. Hoist the generator set enough so that two men can lift the

plywood base and enter the bolts into corresponding holes in generator set rails . Spin nuts finger tight. Assembly may then be lowered into position and bolting completed.

3. The generator set and base may then be bolted to the sub-base through holes in corner of the plywood.

4. To assemble frame . follow the drawing . Be sure that open holes are opposite guide pins and that riveted screw receptacles are opposite screws.

5. On units which require a fan follow this procedure: A. Remove 4 short screws which hold fresh water pump pu lley

hub. B. Reassemble hub with Ian . tan spacer. and 4 cap screws fur-

nished . Tighten securely. 6. Holes for fuel lines. battery cables. remote panel cable . and power

lines are to be cut in the lower skirt by the installer. These holes should be cut to minimum usable size in order to minimize the escape of sound .

7. Make a final check to be sure fan has clearance in its opening . that the fresh air duct from intake plenum to engine air intake is clamped in place , and that there is a tight fit of air plenum against the end of the generator to prevent re-circulation of air .

8. If you plan to order SOUND GUARD , order the generator set with remote panel and cable extension.

CAUTION: With the air discharge end panel removed , the fan is exposed and unprotected . DO NOT remove air discharge end panel without first slopping engine.

SIMPLE OUICK ACTlON LOCK AND RElEASE FASTENINGS

EASY TO ASSEMBLE CORNER DETAIL

BATTERY CONNECTlONS

WATER INJECTED RUBBER "HAI"T--r HOSE TO WATER LIFT TYPE MUFFLER

FLEX DUCT FOR COMBUSTION

CALL YOUR WESTERBEKE REPRESENTATIVE

PRINTED IN USA

SOUND GUARD AIR FLOW DIAGRAM AND DIMENSIONS DIMENSIONS IN INCHES

GENERATOR A B C 0 E WMD3 15 3 30 3 15 WMD4 18 3'0 34 3'h 18 WMD7.7 18 3' 42 3'h 18 WMD 11 & 12.5 19' 3' 48' 3' 19' , WTA 15, 20 & 25 21 5 54 5 21 WTF32 21 5 65'/, 5 21

NOTE: For dimensions of additional SOUND/GUARD units

F G H I J K 32 18 23 20 15 • 36 23 25 25 18 , 'I, 44 23 26 25 18 lV, 51 24', 27% 27 193;' lV, 56 26 30 28 20 1%

670/. 30 33 32 20 1% Westerbeke representative.

1

G I , ~ • ~

H

DISCHARGE FAN

NOTE, FAN ASSEMBLY IS REOUIRED ON CERTAIN MODELS

: .. I=-Ijl\l

SOUND ABSORBENT ~ INSULATION WITH

MYLAR FACING , QUICK ACTION SCREWS

FOR EASY ACCESS

; .. Jllli "7 "!:~ Ir.TIIIII EDGES PROTECT INSULATION

ENAMELED STEEL PANELS ill ALUMINUM HANDLES

An easy to assemble sound enclosure to fit all Westerbeke generators.

ALUMINUM EXTRUSION FRAME WITH DIE CAST CORNERS FOR ACCURACY

Experience the sound of si lence with Westerbeke's all new SOUND GUARD. A sound enclosure that essentially reduces all

generator noise and provides its own air coo ling and ai r exhaust

SOUND GUARD is a r igid, attractive, easy to clean enclosure that consists of five enameled stee l panels fitted to an aluminum

frame and sk irt and a wood base.

SOUND GUARD is lightweight , durable. and requires no maintenance and it can be assembled eaSily in close quarters.

The turn of two " Quick Action" screws will remove each panel for routine inspection or servicing and should major repairs be re-

quired the entire enclosure can be disassembled in a few minutes; no tools are needed. All the generator service lines are installed

thru the aluminum skirt. Westerbeke provides the necessary fittings and connecting hose for water . exhaust , fuel. battery,

and power lines.

SOUND GUARD is carefu l ly pre· packaged with the skirt and base assembled to assure safe arrival and speedy assembly. Inst ruc ti ons are provided on the back of this sheet.

J. H. WESTERBEKE CORP. AVON INOUS TRIAL PARK. AVON. MASS. 02322 ' (67 7) 588· 7700

CA8LE, WESTCORP. AVON ' TELEX, 92 ·4444

WESTERBEKE'S SOUND ENCLOSURE/SPECIFICATIONS & INSTRUCTIONS INSTRUCTIONS

, __ '" 1. Plywood base, generator set bolts and skirt are in place as re-ceived.

2. Hoist the generator set enough so that two men can lift the plywood base and enter the bolts into corresponding holes in generator set rails . Spin nuts finger tight. Assembly may then be lowered into position and bolting completed.

3. The generator set and base may then be bolted to the sub·base through holes in corner of the plywood .

4. To assemble frame, follow the drawing. 8e sure that open holes are opposite guide pins and that riveted screw receptacles are opposite screws.

5. On units which reQuire a fan follow this procedure: A. Remove 4 short screws which hold fresh water pump pulley

hUb. 8. Reassemble hub with fan , fan spacer, and 4 cap screws fur-

nished , Tighten securely. 6. Holes for fuel lines, battery cables , remote panel cable , and power

lines are to be cut in the lower skirt by the installer. These holes should be cut to minimum usable size in order to minimize the escape of sound.

7. Make a final check to be sure fan has clearance in its opening , that the fresh air duct from intake plenum to engine air intake is clamped in place , and that there is a tight fit of air plenum against the end of the generator to prevent re-circulation of air.

8. If you plan to order SOUND GUARO . order the generator set with remote panel and cable extension .

CAUTION: With the air discharge end panel removed , the fan is exposed and unprotected. 00 NOT remove air discharge end panel without first stopping engine.

SIMPLE OUICK ACTION LOCK ANO RElEASE fASTENINGS

EASY TO ASSEMBLE CORNER DETAIL

BATTERY CONNECTIONS

WATER INJECTED RUBBER EXHAUST HOSE TO WATER lifT TYPE MUffLER

fLEX OUCT fOR COMBUSTION AIR

CAll YOUR WESTERBEKE REPRESENTATIVE

MARINE NLP 1181 1SM PRINTEO IN USA

SOUND GUARD AIR FLOW DIAGRAM AND DIMENSIONS DIMENSIONS IN INCHES

GENERATOR A 8 C 0 , F G H WMD4.4 18 3'(' 34 3'(' 18 36 23 25 25 18 WMD7 .7 18 3V, 42 3'(' 18 44 23 26 25 18 WMD11 .0 19V, 3'(' 48 '(' 3'(' 19 V, 51 24% 27'/. 27 19'1. WMD 12.5 19 V, 3V, 48V, 31/2 19 V, 51 24% 27'/. 27 19'1.

NOTE: For dimensions of additional SOUND/GUARD units contact your Westerbeke representative.

,.---G

H

i---- J

DISCHARGE fAN

NOTE: fAN ASSEMBLY IS REQUIRED ON CERTAIN MODElS

(

I

- -- -

:-i1~UI\1

SOUND ABSORBENT .. INSULATION WITH

MYLAR FACING

ENAMELED STEEL PANELS ill

- --

ALUMINUM HANDLES

An easy to assemble sound enclosure to fit all Westerbeke generators.

ALUMINUM EXTRUSION FRAME WITH DIE CAST CORNERS FOR ACCURACY

Experience the sound of silence with Westerbeke's all new SOUND/GUARD. A sound enclosure that essentially reduces all

generator noise and provides its own air cooling and air exhaust

SOUND/GUARD is a rigi d, attractive, easy to clean enclosure that consists of five enameled steel panels fitted to an aluminum

frame and sk irt and a wood base.

SOUND/GUARD is lightweight, durable, and requires no maintenance and it can be assembled easily in close quarters.

The turn of two " Quick Action" screws will remove each panel for routine inspection o r servicing and should major repairs be reo

quired the entire enclosure can be disassembled in a few minutes; no tools are needed. All the generator service lines are insta lled thru the aluminum sk irt. Westerbeke not only provides the pre·

cut ho les but also the necessary fittings and connect ing hose for water, exhaust , fuel , battery, and power lines. Inserts are provided

to fill any unused holes.

SOUND/GUARD is carefull y pre·packaged with the skirt and base assembled to assure safe arrival and speedy assembly. Instructions are provided on the back of this sheet.

J. H. WESTERBEKE CORP. AVON INDUSTRIAL PARK. AVON. MASS. 02322' (617) 588· 7700

CABLE, WESTCORP. AVON' TELEX, 92·4444

WESTERBEKE'S SOUND ENCLOSURE/SPECIFICATIONS & INSTRUCTIONS INSTRUCTIONS SOUND/GUARD AIR FLOW DIAGRAM AND DIMENSIONS

1. Plywood base, generator set bolts and skirt are in place as reo ceived.

2. Hoist the generator set enough so that two men can lift the ply· wood base and enter the bolts into corresponding holes in gen· erator set rails. Spin nuts finger tight. Assembly may then be lowered into position and bolt ing completed.

GENERATOR

WMO 4.4 61 WMO 7.7 61 WPA 15 61

A B

18 3Y, 18 3Y, 21 4Y,

DIMENSIONS IN INCHES

C 0 E

34 3Y, 18 42 3Y, 18 49 4Y, 21

G H J

36 23 25 25 II 44 23 26 25 18 51 25 28Y, 27 20

3. The generator set and base may then be bolted to the sub-base through holes in corners of the plywood. NOTE: For dimensions of additional SOUND/GUARD units contact your Westerbeke representative.

4. To assemble frame, follow the drawing. Be sure that open holes are opposite guide pins and that riveted screw receptacles are op· posite screws.

5. On units which require a fan follow this procedure: _ LJ--IIIIII!Il!l---~~~~~~-" A. Remove 4 short screws which hold fresh water pump pulley -,

hub. .. ...... B. Reassemble hub with fan, fan spacer, and 4 cap screws fur·

nished. Tighten securely. 6. Holes are precut for exhaust fitting, water fitting, fuel lines, bat·

te:y cables, remote panel cable, and power lines out. The latter two are in duplicate on opposite sides of the enclosure. Three skirt fittings are provided and inserts are supplied to plug the un sued holes.

7. Make a final check to be sure fan has clearance in its opening, that Ihe fresh air duct from intake plenum 10 engine air intake is clamped in place, and that there is a tight fit of air plenum against the end of the generator to prevent re·circulation of air.

CAUTION: With the air discharge end panel removed, the fan is eK· posed and unprotected. DO NOT remove air discharge end panel without first stopping engine.

SIMPLE QUICK ACTION LOCK ANO RELEASE fASTENINGS

I-- J

I DISCHARGE fAN

H

EASY TO ASSEMBLE CORNER OETAIL NOTE: fAN ASSEMBLY IS REOUIRED ON CERTAIN MOOELS

BATTERY CONNECTIONS

WATER INJECTEO RUBBER "'14",,, ·-r HOSE TO WATER lifT TYPE MUffLER

CALL YOUR WESTERBEKE REPRESENTATIVE

MARINE LP 5181/5111 PRINTED IN U.S.A. WESTER8EICE CORP.

(