1/14/14 [IRFCA] Indian Railways FAQ: Locomotives - General Information - I

www.irfca.org/faq/faq-loco.html 1/9

Locomotives — Gener al I nfo rmatio n – I

Con tents

Th is pa g e

Classification of locomotives Locomotive manufacturers

Early non-steam locos

On pa g e 2

Miscellaneous, serial numbers, diagrams Wheel arrangement notations

Class ification of Locos

Q. What do the designations such as 'WDM-2' mean?

Locos, except for older steam ones, have classification codes that identify them. This code is of the form '[gauge][power][load][series][subtype][suffix]'

In this the first item, '[gauge]', is a single letter identifying the gauge the loco runs on:

W = Broad GaugeY = Meter GaugeZ = Narrow Gauge (2' 6")N = Narrow Gauge (2')

The second item, '[power]', is one or two letters identifying the power source:

D = DieselC = DC tractionA = AC tractionCA = Dual-power AC/DC tractionB = Battery electric(rare)

The third item, '[load]', is a single letter identifying the kind of load the loco is normally used for:

1/14/14 [IRFCA] Indian Railways FAQ: Locomotives - General Information - I

www.irfca.org/faq/faq-loco.html 2/9

M = Mixed TrafficP = PassengerG = GoodsS = ShuntingL = Light Duty (Light Passenger?) (no longer in use)U = Multiple Unit (EMU / DEMU)R = Railcar (see below)

The fourth item, '[series]', is a digit identifying the model of the loco. Until recently, this series number was simply assigned chronologically as new

models of locos were introduced.

Revised class notation for diesels, 2002: However, starting in 2002, for diesel passenger, goods, and mixed locos, i.e., WDP, WDG, and WDM

sequences, (and only for them, apparently, not for electrics, nor for diesel shunters), the series digit identifies the horsepower range of the loco, with '3'

for locos with over 3000hp but less than 4000hp, '5' for locos over 5000hp but less than 6000hp, etc. This new scheme will be applied to all

passenger/goods/mixed-haul diesel locos starting in June 2002, except for the WDM-2 and WDP-1 classes of locos.

The fifth item, '[subtype]', is an optional letter or number (or two of them) that indicates some smaller variation in the basic model or series, perhaps

different motors, or a different manufacturer. With the new scheme for classifying diesel locos (see above), the fifth item is a letter that further refines

the horsepower indication in 100hp increments: 'A' for 100hp, 'B' for 200hp, 'C' for 300hp, etc. So in this scheme, a WDM-3A refers to a 3100hp loco,

while a WDM-3F would be a 3600hp loco.

The last item, '[suffix]', is an optional indication that indicates something special about the loco, such as a different gearing ratio or brake system than

usual.

So, a WCM-2 is a broad-gauge (W) DC electric (C) mixed traffic (M) engine, model 2. Likewise, a WDS/5 is a broad-gauge diesel shunting engine, model

5, and a ZDM-5 is a narrow-gauge diesel mixed-traffic model 5 loco. YAU-1 is the old series of MG EMUs run on the Madras-Tambaram line.

The subtype indication of minor variations is not very systematic. Often successive variants of a model are given subtypes 'A', 'B', etc. in alphabetic order,

e.g. ZDM-5A, WAM-4A, WAM-4B, etc., but not always. For many loco classes (WDM-2A, WDP-2A, notably), the 'A' also indicates dual braking systems

(capable of hauling air-braked and vacuum-braked stock). But in some, such as the WDM-2CA, the 'A' indicates a loco with only air-brakes. A WAM-4R is a

faster version ('R' for rapid?) of the WAM-4, and WAM-4P is a version of the WAM-4 designed specifically for passenger use ('P'). But a WAM-4 6P is a

version regeared and allowing all-parallel operation of the traction motors. A WDM-2P is a prototype version of a WDM-2 class.

Similiarly, a WAG-5HA is a WAG-5 with Hitachi motors ('H') built by CLW; a WAG-5HB is the same, but built by BHEL. A WAG-5P, interestingly, is a WAG-5

loco (a goods loco in its original design, as indicated by the 'G') which has been modified by re-gearing to haul passenger trains (the 'P' indicates

'passenger')! An 'E' suffix often indicates a variant that is purely air-braked (WAP-1E, WAM-4E, etc., but redundant with a WAP-4E.).

[5/02] As indicated above, a new system of classifying mainline diesels has been introduced. The new scheme got off the ground with rebuilt WDM-2C

locos being reclassified as WDM-3A (as they have a power rating of 3100hp). It is likely that the new classifications will coexist with the old ones for

some time.

1/14/14 [IRFCA] Indian Railways FAQ: Locomotives - General Information - I

www.irfca.org/faq/faq-loco.html 3/9

With the optional suffix, things get even less predictable and less systematic. A WDM-2 5PD is a WDM-2 with a different gearing ratio (the '5P', usually a

'P' in such a suffix indicates a gearing ratio suitable for passenger service). On the other hand a WAM-4 6P indicates all 6 traction motors permanently

connected in parallel — in electric locos 'S' and 'P' often stand for 'series' and 'parallel' combinations of traction motors. Dual brake systems ('D'); similarly

with a WAM-4 6PD, another common designation. (It's been reported that the 'PD' in these may actually refer to suitability for push-pull operation...??) A

WAP-1 FMII is a variant of the WAP-1 using Flexicoil Mark II bogies.

Ad hoc combinations of many such suffixes are possible, as with 'WAM-4 P HS DB 6P' (HS = high speed, DB = dual-brake compatible, P = regeared for

passenger operations, 6P = all 6 traction motors may be placed in parallel operation). The WAM-4 locos, in particular, are notorious for having countless

minor variations as CLW and various workshops keep making minor experimental changes to them. Some sheds follow their own schemes too.

Bhusawal shed, for instance, adds 'DBC' or 'ABC' to loco classes to indicate locos that have undergone conversion of the braking systems ('dual brake

converted', and 'air brake converted').

The model numbers are assigned chronologically as new loco types are brought into use in IR, but there are some exceptions. Sometimes model

numbers are assigned to some experimental locos which are never brought into regular use, e.g., WAG-8.

Some sheds have been known to use non-standard classifications; marking a WDM-2 loco as a 'WDS-2' to indicate it is used only as a shunter is

perhaps one of the more egregiously confusing practices seen in some sheds. 'WDM-2S' is another notation seen at some sheds for WDM-2 locos

relegated to shunting duties.

[4/09] Golden Rock Workshops has embarked on a program to convert old MG engines (YDM-4's?) to broad-gauge; these are designated 'WCDS-6'

where the 'WC' presumably stands for 'Broad-gauge, Converted'.

Some classification codes break the system above: e.g., 'RD' is used as a code indicating the power and the load for diesel railcars, and not 'DR' as one

might expect: YRD-1 is a series of MG railcars, NRD-1 similarly an NG series of railcars. Railcars used on the Tambaram line were classified simply 'RU'. 'RB'

is used for railbuses, e.g., the WRB railbuses built on Ashok Leyland bus frames operating between Bangarpet and Kolar.

EMUs followed this system for some time through the 1950s, but for quite some time now have not done so. There are numerous different models of

EMUs with minor and major variations in use in the Mumbai system and in other systems, and they are no longer distinguished by 'WCU-xxx' class codes

for them. See the DMU/EMU section for more information on types of these multiple units.

There are many ways in which the classification code appears in IR documents, painted on locos, etc.:

WDM 2WDM – 2WDM / 2WDM

The Hindi version is usually a phonetic transcription of the way the classification code would be pronounced in English ('double-you-dee-em') with the

series number in Hindi.

Steam: The last few models of steam locomotives used in India had this system of classification too, with one change, which was that the 'power' code

2

1/14/14 [IRFCA] Indian Railways FAQ: Locomotives - General Information - I

www.irfca.org/faq/faq-loco.html 4/9

was dropped. Hence: 'WG' = BG Goods steam loco, 'WP' = BG passenger steam loco, 'YP' = MG passenger steam loco, etc. However, there are literally

hundreds of types of steam locomotives that have been used in India, and locos classified 'WG', 'WP', etc. are the exception rather than the rule. Steam

locos were classified in a myriad of ways in India, with different systems used by different railways. Some standardization began with the IRS

classifications (see below). Note: Sometimes these steam locos had additional notations, e.g., WGx referred to WG locos fitted with CBC couplers for

working block freight rakes.

The serial number of a particular loco usually follows the classification code on the sides and the front or rear (between the buffers) of the loco. See

the item on numbering below.

Interestingly, DLW seems to have briefly used 'V' as the gauge indication for Cape gauge locomotives it was manufacturing for countries in Africa

(Angola, Sudan, Mozambique, etc.). A 1350hp Cape Gauge locomotive intended for export to Angola and Sudan is sometimes seen designated 'VDM-4'.

Q. What is the history of the classification schemes for locos?

Early locomotives in India had a bewildering variety of classification schemes. Regional railways had their own classification schemes too. For more

details on this, refer to reference works such as Hugh Hughes' classic 4-volume work on Indian locomotives.

The first BESA standard classes appeared in 1903. The HPS, SPS, HGS, and SGS steam loco classes were quite popular. HP = Heavy Passenger, SP =

Standard Passenger, HG = Heavy Goods, SG = Standard Goods. In these, the suffix 'S' stands for 'superheated'. An alternative suffix 'C' indicates a

conversion to superheating, e.g. SGC. A suffix 'M' was sometimes used to mean 'modified', for variant designs. However, these classification codes were

by no means universally adopted, and various railways had their own schemes.

In 1924, when IR decided to classify engines, the initial notation was:

X for broad-gaugeY for meter-gaugeZ for 2' 6" narrow-gaugeQ for 2' 0" narrow-gauge

The IRS (Indian Railway Standard) classes XA, XB, XC, XD, XE, and others in the 'X' series for BG; YA, YB, YC, YD, and YE for MG; and ZA, ZB, ZC, ZD, ZE,

ZF for 2'6" NG; and QA, QB, QC for 2' NG, were all adopted as standards by the Locomotive Standards Committee by 1925 or soon thereafter.

In fact the Q classes were never built, and of the Z classes, only ZB and ZE (and a modified version of ZF to agree with existing locos) classes were built.

Not all locos of a given class were built by the same manufacturer. Some of these class designations were re-used later (e.g., ZD). In 1945, 'IRS' became

'IGR' (Indian Government Railway Standard), although the class notations remained the same.

'W' was used for broad-gauge instead of 'X' soon after World War II, with the introduction of the WP and WG locomotives. 'Q' was also replaced by the

'N' code. Some early electrics had codes beginning with 'E' (EF, EM, EG, etc.), but after about 1945, when diesel and electric locos were included in the

scheme, the codes for motive power were added (D, A, C, CA, B), which have remained unchanged.

1/14/14 [IRFCA] Indian Railways FAQ: Locomotives - General Information - I

www.irfca.org/faq/faq-loco.html 5/9

Post-independence history of 'mixed' vs. dedicated loco models

In the early days locos were classified strictly according to the load: goods engines (G) (e.g. WG, YCG, WCG, WAG, etc), or passenger engines (P) (e.g.

WP, WCP, etc). Then the trend was towards a whole fleet of mixed traffic (M) engines (e.g. WDM, YAM, WAM, WCM, etc.) Between 1960 and 1985 or so,

almost every loco design was of the 'M' variety, with the only two exceptions being the WCG/2 (built 1971 or so) and the WAG series (WAG -

5/5B/5HA/6A/B/C/7). The introduction of the WAP engines in the early '80s indicated a reversal of IR policy in dedicating engines exclusively for

passenger operations once again. Some dedicated diesels (WDP, WDG series) are also now under development.

Locomotive Manufacturers

Q. Where were/are locomotives used in India manufactured?

Early locos (late 19th century) were almost all imported. The first steam locomotive was built in India in 1895 at the Ajmer workshops.

Details of some of the more important manufacturers are to be found in the section on production units and workshops .

Domestic Manufacturers

CLW: Large-scale loco production in India did not begin until the establishment of the Chittaranjan Locomotive Works (CLW) in 1950. More details on

CLW here.

DLW: The Diesel Loco Works set up at Varanasi began producing diesel locos in 1967, and has since then produced a large number of mainline and

shunter diesels. Variants of various classes in the WDS and WDG series are supplied to industrial concerns as well. More details on DLW here.

BHEL: Bharat Heavy Electricals Ltd. (BHEL) supplied some WAG-5 and three NBM-1 units in the '80s, and more recently has suplied WCAM-2's, WCAM-3's,

WAG-8's, and NDM-6's. BHEL also makes electrical transmission components, traction motors, alternators, and other components for both three-phase

and tap-changer locomotives. The locomotives are made at BHEL's facilities at Bhopal and Jhansi. Recently [2008] BHEL has entered an agreement with

IR to supply several dozen high-horsepower locomotives. As its expertise extends currently only to 6,000hp diesel locos, BHEL is exploring foreign

partnerships with GE, Toshiba, and others for production of 10,000hp locomotives.

DCW: Diesel Components Works, Patiala - now renamed the Diesel Modernization Works or DMW, supplies components for some locomotives to DLW. It

also works on rebuilding and upgrading locos (e.g., older WDM-2's being converted to WDM-3A locos). More details on DCW here.

NGEF and Crompton Greaves are other domestic suppliers of traction motors, alternators, etc.

TELCO: Tata Electrical and Locomotive Co. (TELCO) supplied some YP and YG units in the 50's and 60's.

Cummins India makes the diesel engines for DMU's, HPDMU's, and some MG locos.

1/14/14 [IRFCA] Indian Railways FAQ: Locomotives - General Information - I

www.irfca.org/faq/faq-loco.html 6/9

Suri and Nayar (SAN), located in Bangalore, have supplied some shunters and other locos, and parts such as transmissions.

Ovis Loco , based in Hyderabad supplies some shunting locos (mainly for industrial customers).

Venkateshwara Transmissions (Ventra) of Medak (Andhra Pradesh) is another manufacturer who supplied some locomotives and locomotive parts to IR.

ICF: Integral Coach Factory has been making EMUs for suburban systems (e.g., the YAU-1 MG 4-car EMU) since 1966. It also makes some self-propelled

special-purpose units, such as the diesel Medical Relief Van and diesel-electric tower cars. More details on ICF here.

Bharat Earth Movers Limited (BEML) Formerly a state owned enterprise, Bangalore-based BEML manufactures heavy engineering products, including a

wide variety of Railway vehicles made at its Bangalore and Mysore facilities. BEML makes coaches based on the standard ICF type design. A recent

addition to the company's lineup were high tech trainsets (broad gauge and (as of [8/09]) standard gauge) destined for the Delhi Metro. DMRC rolling

stock is manufactured in technical collaboration with the Korean firm ROTEM. In addition, BEML also manufactures Railbuses, OHE vans and track-laying

equipment. BEML had manufactured coaches for the now scrapped MG EMUs service in Chennai. The company is very likely to supply coaches for planned

Metro systems in Bangalore, Mumbai and other places.

Bombardier Transportation makes train-sets for the Delhi Metro at its plant in Vadodara, Gujarat.

The Jamalpur Workshop of ER manufactures diesel self-propelled units such as cranes for clearing wreckage and construction work. More details on

Jamalpur here.

The Izzatnagar Works manufactures railbuses and railcars using Ashok Leyland Iveco engines, and Hindustan Motors or Kirloskar Pneumatics converters

and transmissions.

Jessop & Co., an engineering company founded in 1788 (and now in the public sector) has manufactured wagons, cranes, and EMU rakes (many of the

old EMU rakes in the Calcutta and Mumbai systems were built by Jessop). More details on Jessop here.

Parel Workshops of CR has been assembling BG diesel locomotives since 2006, mostly WDS-6 class shunters, using components from DLW, DCW, and

elsewhere. Between 2006 and 2009 it manufactured about 88 such locomotives, about half of which went to private companies (industrial shunters)

while the others were purchased by IR.

[2007] A new diesel locomotive production facility has been proposed to be set up at Marhora (Marhowra) in the Saran district of Bihar, near Chhapra. IR

is expected to procure 1000 diesel locos of varying power capacities (4,500hp-6,000hp) from this factory over 10 years. This is expected to be a joint

venture with a private (foreign or Indian) manufacturing entity - GE and EMD are considered candidates [2/09].

[2007] A new electric locomotive production facility has been proposed to be set up at Madhepura in Bihar, with a capacity to produce 120 locos a year.

IR is expected to procure 800 electric locos of 12,000hp power capacity from this factory over 10 years. This is expected to be a joint venture with a

private (foreign or Indian) manufacturing entity - Siemens, Alstom, and Bombardier are considered candidates [2/09].

Foreign Manufacturers

There are many foreign suppliers of early locos: dozens of manufacturers are represented, including Bagnall, Beyer-Peacock, Vulcan Foundry, Nasmyth

1/14/14 [IRFCA] Indian Railways FAQ: Locomotives - General Information - I

www.irfca.org/faq/faq-loco.html 7/9

Soviet Locomotives Post-Independence India had a pretty close relationship with the USSR, and had

access to a wide range of Soviet technology in many fields. Interestingly, though, Soviet influence was

extremely limited in the area of locomotives, which was dominated by European and American suppliers

as mentioned above. The Soviet Union helped build some of the steel plants and other industrial sites in

India in the 1950s and 1960s, and a few industrial locomotives did seem to have made their way to India

from the USSR. In particular, 36 type TEL Bo-Bo DE locomotives, of 5'6" gauge, variants of the TGM-3

750hp end cab switchers are listed in some locomotive compilations as intended for India. These were

built around 1957 at Lugansk. A TEV version appears to have been built at 1958, also at Lugansk. While it

is not entirely certain, it seems likely these were intended for the Bhilai Steel Plant which was built with

Soviet help and commissioned in 1959. Iron ore for the plant was mined at Dalli-Rajhara and transported

over a 85.5km railway line to Bhilai, which opened on May 14, 1958. A 20km line connected Bhilai to

Ahiwara where limestone was quarried; this line was opened on April 1, 1960.

(Information from the WDL mailing list, posted by John Middleton. Reference: Vitaly Rakov,

Locomotives of our country's railways, 1995, Moscow, ISBN 5-277-00821-7.)

Wilson, SLM, Kerr-Stuart, Henschel, Hunslet, Dubbs & Co. (Glasgow), Metropolitan Carriage and Wagon Works, Sentinel Carriage and Wagon Works

(Shrewsbury), Freid Krupps, Sharp Stewart, Kitson-Meyer, Kawasaki, General Electric, etc.

More recent foreign suppliers of locos include Alco (WDM-1, some WDM-2, some YDM-4), GM (WDG-1, WDM-4, YDM-3, YDM-5), English Electric (WCM-1,

WCM-2), Henschel (WDM-3), Maschinenbau Kiel (WDS-3, ZDM-2), Montreal Loco Works (YDM-4A), Hitachi (WCM-3, WCM-4, some WAG-2), Mitsubishi

(WAM-2, WAM-3, YAM-1, some WAG-2), Asea Brown-Boveri (WAP-5, some WAG-9), Toshiba (some WAG-2), Krupp (some WAM-1), Alsthom (some WAM-1),

Kraus-Maffei (some WAM-1), General Motors EMD (WDP-4, WDG-4, some WDM-4), and Arn. Jung (NDM-1).

Cranes and other equipment have been supplied by Gottwald, Sheldon, ABB, etc. Jamalpur workshops makes many kinds of break-down cranes.

Tower cars and track and OHE inspection vehicles are manufactured by CLW and Jamalpur Workshops.

Industrial locomotives of various kinds were supplied by Andrew Barclay, Brookville, Baldwin, Henschel, Canadian Loco. Co., Greenwood Batley, Ruston &

Horsnby, TELCO, Arn. Jung, Kraus-Maffei, GE, and many others.

Ear ly non-steam locos

Q. Which were the earliest diesel locomotives in the Indian subcontinent?

In 1915, a 2'6" gauge diesel loco was supplied to the India Office by Avonside (Bristol). This is presumed to have worked on some tea plantation in

Assam.

1/14/14 [IRFCA] Indian Railways FAQ: Locomotives - General Information - I

www.irfca.org/faq/faq-loco.html 8/9

In 1921, a 2'0" gauge 0-4-0 diesel loco built by Baugleys of Burton-on-Trent was delivered to Bengal.

In 1923, two diesel locos built by Ruton Proctor of Lincoln were used on the Barsi Light Railway.

In 1929, a 2'0" gauge 0-4-0 diesel loco was supplied by Maffei (Germany) to C K Andrew, London, for delivery to India. Their ultimate use and disposition

in India is not known.

Two 420hp (or 350hp?) dual-cab BG diesel shunters from William Beardmore (with electrical components from GEC) were used by the North-Western

Railway (now in Pakistan) in 1930.

In 1934, an Armstrong-Whitworth diesel-electric railcar was delivered to NWR for use on the 2'6" Kalka-Simla.

In 1935, two 1200hp BG diesel-electric locos with 8-cylinder Armstrong-Sulzer engines, built by Armstrong-Whitworth, were obtained by NWR for trials

on the Karachi-Lahore line in preparation for a proposed new Karachi-Bombay route. They had a 1A-C-2 wheel arrangement. None of these experiments

proved successful and the locos were in all cases withdrawn very soon.

Ceylon Government Railways obtained one diesel-electric shunter and two diesel-electric mixed traffic locos in 1934 from Armstrong Whitworth. The two

mixed traffic locos were actually made for the Indian State Railways (as they were then known) but turned out to be of too low a power for their

requirements and were sold to CGR. These proved unsuitable and were sent to Argentina in 1937, and ultimately scrapped soon thereafter.

Between 1930 and 1940, various Indian industrial concerns obtained 14 diesel locos. Bagnall in conjunction with Duetz supplied a 4-speed 22-25hp

diesel loco (Duetz PM 2117 design) in 1934 to Bundla Beta Tea Co., Assam for the Pengarie-Digboi trolley line. It had a top speed of about 15km/h. In

1936, BBCI obtained one diesel-electric shunter from Armstrong-Whitworth which survived into the 1950's. In 1940, the Jamnagar and Dwarka Railway

obtained one MG diesel from Brookville (USA).

In the mid-1930s, the Nizam's State Railways obtained a few diesel railcars from Ganz. These were in use until the 1950s or so. Ganz supplied NWR in

1939-40 with some diesel railcars as well. Some of these were allocated to India when NWR assets were split following the partition of British India.

In 1944-45, the USATC supplied 15 GE-built BG Bo-Bo diesel locos with Caterpillar engines to WR. These were mid-cab machines with short and narrow

hoods on either side. Several of these were working until about 1990, when they were withdrawn and scrapped. One is preserved at the Diesel Loco

Works, Varanasi.

In 1949, a few MG diesel-mechanical locos built by Fowler were imported by IR for use in the arid regions of Saurashtra. One of these is preserved at the

National Rail Museum, New Delhi. In 1955, 20 'DY' diesels by North British were imported for use, also in Saurashtra (MG). The locos of the second batch

were reclassified as YDM-1's, and a few still survive [1/00].

Q. Which were the earliest electric locomotives in India?

Two MG electric locos using overhead electrification were supplied to the Mysore Gold Fields in 1910 by Bagnalls of Stafford. Electrical equipment for

these was supplied by Siemens.

1/14/14 [IRFCA] Indian Railways FAQ: Locomotives - General Information - I

www.irfca.org/faq/faq-loco.html 9/9

Electrically operated rail trolleys (patented by T A White, an EIR engineer, and hence known as White's Patented Rail Motor Trolleys) were used in a few

places beginning in 1910. EIR's Liluah Carriage and Wagon works used one between Liluah and Howrah; the Oudh and Rohilkand Rly. also used one for

track inspections. In the following years Jessop and Co. supplied a few more of these to various railways.

In 1922 an electric loco (unknown gauge) using overhead electrification was supplied to the Naysmyth Patent Press Co. in Calcutta by British Electric

Vehicles.

Q. Other than diesels, were there other internal-combustion locos used in India?

For contemporary applications, see the section on alternative fuels .

In 1905 Kerr Stuart delivered a 12hp 0-4-0 petrol-driven 2'6" loco to Morvi Railway and Tramways.

In 1909, a railcar with a Dodge petrol engine was supplied to the Matheran Light Rly.

In 1909, a 0-6-0 petrol-driven MG loco was supplied by McEwewn Pratt and Co. of Wickford in Essex to Assam Oil Co. In 1910, Morvi Railway and

Tramways obtained a 30hp 0-4-0 petrol-driven 2'6" loco from Nasmyth Wilson. In 1910 and 1911, a few petrol-driven parcel delivery vehicles were

supplied to EIR by Thornycroft. Another 13 petrol-driven locos were delivered by various builders up to 1920, and a further 75 between 1920 and 1930.

Their use started declining after that, and only 27 more were ordered later (until 1940).

Some petrol-driven railcars were built by the Motor Rail and Tram Co., Ltd., and supplied to the South Indian Rly. in 1925. Their engines were rated

65bhp at 1000rpm; a railcar seated 85. They were refitted with diesel engines in the late 1930s.

The Shahdara-Saharanpur 2'6" Light Railway had a petrol railcar supplied by D Wickham Co. in 1935.

A Brookville petrol locomotive was used by the Matheran Light Railway in 1928. Two railcars (one seating 8, the other seating 14) with Dodge petrol

engines and chain drives were also used by this railway (1909, 1927).

Three alcohol-fuelled MG locos with mechanical transmissions were supplied by Davenport Locomotive Works (Iowa, USA) to some unknown Indian

industrial concern in 1949.