IPS-E-PR-730(1) · 2012. 11. 10. · IPS shall form the job specification for the specific project...
Transcript of IPS-E-PR-730(1) · 2012. 11. 10. · IPS shall form the job specification for the specific project...
-
IPS-E-PR-730(1)
-
FOREWORD
The Iranian Petroleum Standards (IPS) reflect
the views of the Iranian Ministry of Petroleum
and are intended for use in the oil and gas
production facilities, oil refineries, chemical and
petrochemical plants, gas handling and
processing installations and other such facilities.
IPS is based on internationally acceptable
standards and includes selections from the items
stipulated in the referenced standards. They are
also supplemented by additional requirements
and/or modifications based on the experience
acquired by the Iranian Petroleum Industry and
the local market availability. The options which
are not specified in the text of the standards are
itemized in data sheet/s, so that, the user can
select his appropriate preferences therein.
The IPS standards are therefore expected to be
sufficiently flexible so that the users can adapt
these standards to their requirements. However,
they may not cover every requirement of each
project. For such cases, an addendum to IPS
Standard shall be prepared by the user which
elaborates the particular requirements of the
user. This addendum together with the relevant
IPS shall form the job specification for the
specific project or work. The IPS is reviewed and up-dated approximately
every five years. Each standards are subject to
amendment or withdrawal, if required, thus the
latest edition of IPS shall be applicable The users of IPS are therefore requested to send
their views and comments, including any
addendum prepared for particular cases to the
following address. These comments and
recommendations will be reviewed by the
relevant technical committee and in case of
approval will be incorporated in the next revision
of the standard.
Standards and Research department
No.19, Street14, North kheradmand
Karimkhan Avenue, Tehran, Iran .
Postal Code- 1585886851 Tel: 88810459-60 & 66153055 Fax: 88810462 Email: [email protected]
پيش گفتار
منعكس كننده ديدگاههاي ) IPS(استانداردهاي نفت ايران
وزارت نفت ايران است و براي استفاده در تأسيسات توليد
نفت و گاز، پااليشگاههاي نفت، واحدهاي شيميايي و
پتروشيمي، تأسيسات انتقال و فراورش گاز و ساير تأسيسات
.مشابه تهيه شده است
س استانداردهاي قابل قبول استانداردهاي نفت، براسا
هايي از استانداردهاي المللي تهيه شده و شامل گزيده بين
همچنين براساس تجربيات . باشد مورد مي مرجع در هر
صنعت نفت كشور و قابليت تأمين كاال از بازار داخلي و نيز
برحسب نياز، مواردي بطور تكميلي و يا اصالحي در اين
هاي فني كه در واردي از گزينهم. استاندارد لحاظ شده است
ها بصورت متن استانداردها آورده نشده است در داده برگ
شماره گذاري شده براي استفاده مناسب كاربران آورده شده
.است
استانداردهاي نفت، بشكلي كامالً انعطاف پذير تدوين شده
. است تا كاربران بتوانند نيازهاي خود را با آنها منطبق نمايند
هاي پروژه ها را ين حال ممكن است تمام نيازمنديبا ا
اي كه نيازهاي در اين گونه موارد بايد الحاقيه. پوشش ندهند
اين . نمايد تهيه و پيوست نمايند خاص آنها را تأمين مي
الحاقيه همراه با استاندارد مربوطه، مشخصات فني آن پروژه
.و يا كار خاص را تشكيل خواهند داد
ي نفت تقريباً هر پنج سال يكبار مورد بررسي استانداردها
ها ممكن است در اين بررسي. گردند قرار گرفته و روزآمد مي
اي به آن اضافه شود و بنابراين استانداردي حذف و يا الحاقيه
.همواره آخرين ويرايش آنها مالك عمل مي باشد
نظرها و شود نقطه از كاربران استاندارد، درخواست مي
اي كه براي موارد ات اصالحي و يا هرگونه الحاقيهپيشنهاد
نظرات و . اند، به نشاني زير ارسال نمايند خاص تهيه نموده
هاي فني مربوطه بررسي و در پيشنهادات دريافتي در كميته
صورت تصويب در تجديد نظرهاي بعدي استاندارد منعكس
.خواهد شد
الي، كوچه ايران، تهران، خيابان كريمخان زند، خردمند شم
19چهاردهم، شماره
اداره تحقيقات و استانداردها
1585886851: كدپستي
66153055و 88810459 - 60: تلفن
88810462: دور نگار
[email protected] : يالكترونيك پست
-
General Definitions:
Throughout this Standard the following
definitions shall apply.
:تعاريف عمومي
.در اين استاندارد تعاريف زير به كار مي رود
Company :
Refers to one of the related and/or affiliated
companies of the Iranian Ministry of Petroleum
such as National Iranian Oil Company, National
Iranian Gas Company, and National
Petrochemical Company etc.
:شركت
به شركت هاي اصلي و وابسته وزارت نفت مثل شركت ملي
نفت ايران ، شركت ملي گاز ايران، شركت ملي صنايع
. پتروشيمي و غيره اطالق ميشود
Purchaser :
Means the “Company" Where this standard is
part of direct purchaser order by the “Company”,
and the “Contractor” where this Standard is a part
of contract documents.
:خريدار
كه اين استاندارد بخشي از مدارك سفارش "شركتي"يعني
كه اين "پيمانكاري"ميباشد و يا "شركت"خريد مستقيم آن
.استاندارد بخشي از مدارك قرارداد آن است
Vendor And Supplier:
Refers to firm or person who will supply and/or
fabricate the equipment or material.
:فروشنده و تامين كننده
به موسسه و يا شخصي گفته ميشود كه تجهيزات و كاالهاي
.د مورد لزوم صنعت را تامين مينماي
Contractor:
Refers to the persons, firm or company whose
tender has been accepted by the company,
:پيمانكار
به شخص ، موسسه ويا شركتي گفته ميشود كه پيشنهادش
.براي مناقصه ويا مزايده پذيرفته شده است
Executor :
Executor is the party which carries out all or part
of construction and/or commissioning for the
project.
: مجري
مجري به گروهي اتالق مي شود كه تمام يا قسمتي از
.كارهاي اجرايي و يا راه اندازي پروژه را انجام دهد
Inspector :
The Inspector referred to in this Standard is a
person/persons or a body appointed in writing by
the company for the inspection of fabrication and
installation work
:بازرس
در اين استاندارد بازرس به فرد يا گروهي اتالق مي شود كه
كتباً توسط كارفرما براي بازرسي ساخت و نصب تجهيزات
.معرفي شده باشد
Shall:
Is used where a provision is mandatory.
:بايد
.براي كاري كه انجام آن اجباري است استفاده ميشود
Should
Is used where a provision is advisory only.
:توصيه
.براي كاري كه ضرورت انجام آن توصيه ميشود
Will:
Is normally used in connection with the action
by the “Company” rather than by a contractor,
supplier or vendor.
: ترجيح
شود كه انجام آن كار براساس معموالً در جايي استفاده مي
.نظارت شركت باشد
May:
Is used where a provision is completely
discretionary.
: ممكن است
.براي كاري كه انجام آن اختياري ميباشد
-
IPS-E-PR-730(1)
ENGINEERING STANDARD
FOR
PROCESS DESIGN PLANT WASTE-WATER TREATMENT
AND RECOVERY SYSTEMS
FIRST REVISION
FEBRUARY 2010
استاندارد مهندسي
براي
تصفيه سامانه هاي ينديآحي فراطر
كارخانه پساب و بازيابي
ويرايش اول
1388بهمن
This Standard is the property of Iranian Ministry of Petroleum.
All rights are reserved to the owner. Neither whole nor any
part of this document may be disclosed to any third party,
reproduced, stored in any retrieval system or transmitted in
any form or by any means without the prior written consent of
the Iranian Ministry of Petroleum.
تمام حقوق آن متعلق به . اين استاندارد متعلق به وزارت نفت ايران است
بدون رضايت كتبي وزارت نفت ايران، تمام يا مالك آن بوده و نبايد
بخشي از اين استاندارد ، به هر شكل يا وسيله ازجمله تكثير، ذخيره
.سازي، انتقال، يا روش ديگري در اختيار افراد ثالث قرار گيرد
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
1
CONTENTS: Page
No.
:فهرست مطالب
0. INTRODUCTION ............................................. 5
5.............................................................. مقدمه -0
1. SCOPE ................................................................ 7
7......................................................دامنه كاربرد - 1
2. REFERENCES .................................................. 9
9............................................................. مراجع -2
3. DEFINITIONS AND TERMINOLOGY ......... 11
11................................................ و واژگان فيتعار - 3
3.1 Biochemical Oxygen Demand (BOD) ........ 11
BOD) .............11)مورد نياز بيوشيميايي اكسيژن 1- 3
3.2 Chemical Oxygen Demand (COD) ............. 11
COD) ...............11)مورد نياز شيميايي اكسيژن 2- 3
3.3 Coagulant Aids............................................. 12
12.................................... ها كمك منعقد كننده 3- 3
3.4 Coagulation and Coagulants ...................... 12
12................................ انعقاد و منعقد كننده ها 4- 3
3.5 Dissolved Oxygen (DO) ............................... 12
DO) .................................12) اكسيژن محلول 5- 3
3.6 Effluent ......................................................... 12
12.......................................... فاضالب خروجي 6- 3
3.7 Effluent Limitation ...................................... 12
12............................ محدوديت فاضالب خروجي 7- 3
3.8 Flocculation .................................................. 12
12................................................ لخته سازي 8- 3
3.9 Immediate Oxygen Demand (IOD) ............ 12
IOD) ............................12)اكسيژن فوري نياز 9- 3
3.10 Susceptibility to Separation (STS) Number ........................................................ 12
STS) .........................12)جداسازي قابليت عدد 10- 3
3.11 Surface Water ............................................ 13
13................................................ آب سطحي 11- 3
3.12 Total Organic Carbon (TOC) ................... 13
TOC) ..................................13)كل كربن آلي 12- 3
4. SYMBOLS AND ABBREVIATIONS ............. 13
13.......................................... نشانه ها و اختصارات - 4
5. UNITS ................................................................. 14
14............................................................ واحدها -5
6. WASTE-WATER TREATMENT.................... 14
14.................................................... پساب هيتصف - 6
6.1 Nature of Waste-Waters ............................. 14 14...............................................پساب ماهيت 1- 6
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
2
6.2 Treatment Stages ......................................... 17
17.............................................. هيمراحل تصف 2- 6
6.3 Treatment Processes .................................... 22
22......................................... هيتصف يندهايفرا 3- 6
7. PHYSICAL UNIT OPERATIONS .................. 41
41........................................ يكيزيواحد ف اتيعمل - 7
7.1 Flow Measurement ...................................... 41
41........................................ اندازه گيري جريان 1- 7
7.2 Screening ...................................................... 46
46............................................... كردنغربال 2- 7
7.3 Comminution ............................................... 46
46................................................... كردن ريز 3- 7
7.4 Grit Removal ................................................ 47
47................................... شن و ماسه يجداساز 4- 7
7.5 Gravity Separation ...................................... 47
47............................................ يثقل يجداساز 5- 7
7.6 Flow Equalization ........................................ 76
76.................................... انيجر يساز يكسان 6- 7
7.7 Mixing ........................................................... 77
77.............................................. مخلوط كردن 7- 7
7.8 Sedimentation .............................................. 79
79............................................ ته نشين سازي 8- 7
7.9 Dissolved Air Floatation (DAF) .................. 82
DAF( ..............82(حل شده يهوابا يساز شناور 9- 7
7.10 Granular-Media Filters ............................. 97
97.............................. ميان دانه ايصافي هاي 10- 7
8. CHEMICAL TREATMENT ............................ 109
109................................................. ييايميش هيتصف -8
8.1 Definition and Application .......................... 109 109............................................. و كاربرد فيتعر 8-1
8.2 Chemical Precipitation ................................ 111
111................................... ييايميرسوب دادن ش 8-2
8.3 Chemical Flocculation ................................. 114
114................................... سازي شيميايي لخته 8-3
8.4 Disinfection ................................................... 123
123......................................... كردن يضد عفون 8-4
8.5 Chlorination ................................................. 124
124.............................................. ار كردنكلرد 8-5
9. BIOLOGICAL TREATMENT ........................ 128
128................................. )يكربيم( يكيولوژيب هيتصف -9
9.1 Objectives ..................................................... 128 128........................................................ اهداف 9-1
9.2 Biological Treatment Processes .................. 128
128.......................... فرايندهاي تصفيه بيولوژيكي 9-2
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
3
9.3 Activated Sludge Units ................................ 132
132.............................. لجن فعال شده يواحدها 9-3
10. EFFLUENT PERMISSIBLE CONCENTRATIONS ...................................... 144
144........................ مجاز فاضالب خروجي يغلظت ها - 10
APPENDICES:
:ها وستيپ
APPENDIX A CONTAMINANT IMPORTANCE
IN WASTE-WATER
TREATMENT .............................. 148
اهميت آالينده ها در تصفيه - الف وستيپ
148................................................... پساب
APPENDIX B TYPICAL WASTE COMPOUNDS
CLASSIFIED AS PRIORITY
POLLUTANTS ........................... 150
نمونه اي از دسته بندي تركيبات پساب -پيوست ب
150.............. آلوده كننده هاي اولويت دار بعنوان
APPENDIX C TOXIC ORGANIC COMPOUNDS
OCCUPATIONAL EXPOSURE TO
CARCINOGENIC
SUBSTANCES ............................. 152
يسم يآل باتيركت با مواد تماس در حين كار - پيوست ج
152................................................ سرطان زا
APPENDIX D CHARACTERISTICS OF
FLOW-METERING DEVICES
USED IN WASTE-WATER
TREATMENT FACILITIESa .... 155
مورد انيجر يريلوازم اندازه گ يشاخص ها -د وستيپ
155................... بپسا هياستفاده در وسائل تصف
APPENDIX E OIL-WATER SEPARATOR
CHANNEL LENGTH CORRECTIONS
FOR TURBULENCE AND SHORT-
CIRCUITING .............................. 158
اصالح طول كانال جداكننده بيضرا - هـ وستيپ
158...... متالطم و اتصال كوتاه انيجر آب –روغن
APPENDIX F TYPICAL OIL TRAP .................. 160
160................................ از تله روغن ينمونه ا - و وستيپ
APPENDIX G TYPICAL OIL HOLDING
BASIN .......................................... 161
161............. روغن ينگهدارحوضچه از ينمونه ا -ز وستيپ
APPENDIX H TYPES OF SETTLING
PHENOMENA INVOLVED IN
ASTE-WATER TREATMENT .... 162
در ريدرگ ينيته نش يها پديدهاع انو - ح وستيپ
162........................................... پساب هيتصف
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
4
APPENDIX I DOWN FLOW SAND FILTER
(TYPICAL) ..................................... 164
164............ نيپائ انيجر يشنصاف از ينمونه ا -ط وستيپ
APPENDIX J ADDITIONAL CHEMICAL
APPLICATIONS IN WASTE-
WATER COLLECTION,
TREATMENT, AND DISPOSAL . 165
،يدر جمع آور ياضاف ييايميمواد ش يكاربردها - ي وستيپ
165................................. و دفع پساب هيتصف
APPENDIX K CHARACTERISTICS OF AN
IDEAL CHEMICAL
DISINFECTANT ......................... 167
ييايميكننده ش يضدعفون كي يشاخص ها - ك وستيپ
167................................................. آل دهيا
APPENDIX L RELATIVE BIODEGRADABILITY
OF CERTAIN ORGANIC
COMPOUNDS .............................. 168
168..... تجزيه ميكربي نسبي بعضي تركيبات آلي - ل وستيپ
APPENDIX M EFFLUENT PERMISSIBLE
CONCENTRATIONS ................ 170
170............... خروجي غلظت هاي مجاز فاضالب- پيوست م
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
5
0. INTRODUCTION
“Design of Miscellaneous Processes in OGP
Industries” are broad and contain various
subjects of paramount importance including
waste water treatment and recovery systems.
Therefore, a group of Process Engineering
Standards are prepared to cover this subject. This
group includes the following Standards:
مقدمه -0
روشيمي طراحي فرايندهاي مختلف در صنايع نفت، گاز و پت
بسيار گسترده بوده و شامل موضوعات متفاوت و با اهميتي
. در ارتباط با تصفيه پساب و سامانه هاي بازيابي مي باشد
بنابراين تعدادي از استانداردهاي مهندسي فرايند براي اين
:اين استانداردها عبارتند از .موضوع تهيه شده اند
STANDARD CODE STANDARD TITLE موضوع استاندارد نداردكد استا
IPS-E-PR-700 "Engineering Standard for Process Design of Crude Oil
Electrostatic Desalters"
IPS-E-PR-700 " استاندارد مهندسي براي طراحي
فرايندي نمك زداهاي
"فت خامالكترواستاتيكي ن
IPS-E-PR-725 "Engineering Standard for Process Design of Plant
Waste Water Sewer
Systems"
IPS-E-PR-725 " استاندارد مهندسي براي طراحي
مجاري هاي فرايندي سامانه
"فاضالب پساب كارخانه
IPS-E-PR-730 "Engineering Standard for Process Design of Plant
Waste Water Treatment and
Recovery Systems"
IPS-E-PR-730 " استاندارد مهندسي براي طراحي
تصفيه و فرايندي سامانه هاي
"كارخانه بازيابي پساب
IPS-E-PR-735 "Engineering Standard for Process Design of Plant Solid
Waste Treatment & Disposal
Systems"
IPS-E-PR-735 " استاندارد مهندسي براي طراحي
تصفيهدفع و فرايندي سامانه هاي
"ضايعات جامد كارخانه
This Engineering Standard Specification covers: ندارد مهندسي عنوان زير را پوشش ميدهداين مشخصه استا:
"PROCESS DESIGN OF PLANT WASTE
WATER TREATMENT AND RECOVERY SYSTEMS"
طراحي فرايندي سامانه هاي تصفيه و بازيابي پساب "
"كارخانه
The treatment of waste waters, involves a
sequence of treatment steps. Every one of the
waste water treatment processes involves the
separation of solids from water in at least some
part of the operation and removal of BOD in
some extent. The end of pipe treatment sequence
can be divided into the following elements.
Primary or pretreatment, intermediate treatment,
secondary treatment and tertiary treatment plus
ancillary, sludge dewatering and disposal
operations.
شامل مي ، يك رشته از مراحل تصفيه را ها تصفيه پساب
هركدام از فرايندهاي تصفيه پساب شامل جداسازي . شود
جامدات از آب حداقل در چند قسمت از عمليات و از بين
تصفيه مي تواند به مراحللوله انتهاي .مي باشد BODبردن
تصفيه اوليه يا پيش تصفيه، تصفيه :موارد زير تقسيم گردد
مياني، تصفيه ثانويه و تصفيه سوم بعالوه تصفيه كمكي، آب
.دفعگيري از لجن و عمليات
The key to optimize the treatment sequence for
provision of maximum water treatment at
minimum cost, is to identify the rule of each
Unit operation and optimize that operation.
Optimizing the performance of specific Unit
تعيين نقش هر كدام از عمليات واحد و بهينه سازي عمليات
حداكثر آن، كليد بهينه سازي مراحل تصفيه براي داشتن
بهينه سازي بازدهي هر .تصفيه آب با حداقل هزينه است
، شناور APIكدام از عمليات واحد خاص مثال جدا كننده
userUnderline
userUnderline
userUnderline
userUnderline
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
6
operations, such as API Separator, Dissolved Air
Flotation, Biological Treatment, etc. can best be
achieved if:
بي و غيره به بهترين وهواي محلول، تصفيه ميكر با سازي
:وجهي قابل دستيابي خواهند بود اگر
a) The properties of influent streams are
considered;
؛فاضالب مد نظر قرار گيرد هاي جريان خواص )الف
b) The chemical principles that are used in
solids pretreatment are understood;
مواد شيميايي مورد استفاده در پيش تصفيه اصول )ب
؛جامدات شناخته شوند
c) The variety of chemicals available for
solids treatment is recognized;
انواع مواد شيميايي قابل دسترسي براي تصفيه )ج
؛جامدات شناخته شوند
d) The properties of effluent water are
established based on the Local Environmental
Regulations and final disposal;
بر اساس قوانين زيست خروجيفاضالب خواص )د
؛ابل دفع نهايي تعيين گردندمحيطي محلي و مواد ق
e) The protocols for quantifying results are
identified.
؛قرارداد ها براي تعيين كميت نتايج مشخص شوند )ه
In general, most industries require water for
processing or other purposes; much of this water
after use is discharged either to public and/or
natural water sources or directed to recycling
purpose inside the industry. Such discharge,
which may contain a wide variety of matter in
solution or suspension should be controlled
according to the requirements imposed by the
final destination and/or Environmental
Regulations.
بطور كلي اكثر صنايع به آب براي فرايند يا ديگر مقاصدشان
بيشتر اين آبها بعد از استفاده يا به منابع آبهاي . نياز دارند
براي بازيابي بهيا عمومي تخليه شده و يا مستقيما و طبيعي
اين آبهاي تخليه شده ممكن .فرستاده مي شوند واحدداخل
ق باشند كه بايستي طبق است داراي انواع مواد محلول يا معل
يا قوانين زيست و الزامات وضع شده توسط گيرنده آب
.محيطي كنترل گردند
A model sequence for the treatment of oil, gas
and petrochemical industries waste waters is
shown in Fig. 1.
، گاز و پتروشيمي نفت صنايع پسابمدلي از مراحل تصفيه
.نشان داده شده است 1ل در شك
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
7
1. SCOPE
This Engineering Standard Specification covers
minimum requirements for the process design
and engineering of the equipment and facilities
pertaining to the waste water treatment Units of
Oil and gas refineries, chemical plants, oil
terminals, petrochemical plants and other
facilities as required.
دامنه كاربرد - 1
استاندارد مهندسي حداقل الزامات الزم براي مشخصه اين
طراحي فرايندي و مهندسي تجهيزات و وسائل مربوط به
واحدهاي تصفيه پساب پااليشگاه هاي نفت و گاز، واحدهاي
پايانه هاي نفتي، واحدهاي پتروشيميايي و ديگر شيميايي،
.پوشش مي دهدخدمات مورد نياز را
As far as Environmental Regulations are
concerned, extent of application of all systems,
facilities and/or methods as outlined in this
Standard should be advised by the Company for
each project.
تا آنجا كه به قوانين زيست محيطي مربوط مي شود، مقدار
يا روش ها كه در اين /و تاسيساتاستفاده از همه سامانه ها،
براي هر كارفرمااستاندارد به اختصار ذكر شده بايستي توسط
.پروژه توصيه گردد
Included in the scope are: امنه كاربرد عبارتند ازموارد در نظر گرفته شده در د:
i) Liquid and solid disposal systems. i (سامانه هاي دفع مايعات و جامدات
ii) Primary oil/solids removal facilities (API
Separators).
ii( جدا ( جامدات اوليه/ مواد نفتيحذف تأسيسات
)API هاي كننده
iii) Further oil & suspended solids removal
(secondary oil/solids removal) such as
Dissolved-Air Flotation Unit.
iii ( جدا كردن ( مواد نفتيجامدات معلق و بيشترحذف
مانند واحد شناورسازي هواي ) مواد نفتي/ جامداتثانويه
محلول،
Granular Media Filters and Chemical
Flocculation Units.
دانه اي و واحدهاي لخته سازي يميان يصافي ها
شيميايي
iv) Chemical Addition Systems. iv( افزودن مواد شيميايي سامانه هاي
v) Biological Treatment. v( بيولوژيكيتصفيه
vi) Filtration and/or other final polishing. vi( كردن و يا ساير پرداخت هاي نهاييصاف
Excluded from the scope are: در دامنه كاربرد عبارتند از ءموارد استثنا:
i) Sewage system handling domestic and
medical sanitary appliances of buildings.
i( بهداشتي و خانگي و سامانه فاضالب حاوي فاضالب
.پزشكي از لوازم ساختمان ها
ii) Drainage system carrying surface and
rainwater.
ii( سامانه تخليه آبهاي سطحي و آب باران.
iii) Waste water gathering systems. iii( سامانه هاي جمع آوري پساب.
iv) Clean water drainage, e.g., from buildings
and paved areas.
iv( محوطه تخليه آب تميز و مانند آن از ساختمان ها و
.تسطيح شده
v) Evaporation ponds and disposal by natural
percolation into the subsoil in permeable
ground.
v( دفع آب بوسيله نشت به زير و تبخير حوضچه هاي
.خاك در زمين هاي نفوذ پذير
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
8
vi) Sanitary sewage treatment. vi( تصفيه فاضالب بهداشتي.
vii) Sludge handling and treatment. vii( انتقال و تصفيه لجن.
This Engineering Standard Specification shall be
read in conjunction with the Standards
Specifications listed below:
معيارهاي اين استاندارد مهندسي بايستي همراه معيارهاي
ه قرار استانداردهايي كه در زير ليست شده اند مورد مطالع
:گيرند
STANDARD CODE STANDARD TITLE موضوع استاندارد كد استاندارد
IPS-E-CE-380 "Engineering Standard for Sewerage & Surface Water
Drainage System"
IPS-E-CE-380 " ـ راي سـامانه استاندارد مهندسـي ب
و تخليــــه آب شــــبكه فاضــــالب
"سطحي
IPS-E-CE-390 "Engineering Standard for Rain & Foul Water Drainage
of Buildings"
S-E-CE-390 " استاندارد مهندسي براي آب بـاران
"ساختمان هاتخليه آلودهآب و
IPS-E-CE-400 "Engineering Standard for
Sanitary Sewage Treatment"
IPS-E-CE-400 " استاندارد مهندسـي بـراي تصـفيه
"فاضالب بهداشتي
IPS-C-CE-342 "Construction Standard for Water Supply & Sewerage
Systems"
IPS-C-CE-342 " استاندارد ساخت براي سامانه هاي
"و شبكه فاضالب تامين آب
IPS-M-CE-345 "Material Standard for Water Supply & Sewerage
Equipment"
IPS-M-CE-345 " تـامين تاستاندارد مواد براي تجهيـزا
"و شبكه فاضالب آب
IPS-E-PI-240 "Engineering Standard for
Plant Piping Systems"
IPS-E-PI-240 " استاندارد مهندسـي بـراي سـامانه
"هاي لوله كشي واحد
IPS-E-SF-880 "Engineering Standard for
Water Pollution Control"
IPS-E-SF-880 " استاندارد مهندسـي بـراي كنتـرل
"آلودگي آب
IPS-E-PR-725 "Engineering Standard for Process Design of Plant
Waste Water Sewer Systems"
IPS-E-PR-725 " استاندارد مهندسي بـراي طراحـي
مجــاريفراينــدي ســامانه هــاي
"ب كارخانهفاضالب پسا
IPS-E-PR-735 "Engineering Standard for Process Design of Plant Solid
Waste Treatment & Disposal
Systems"
IPS-E-PR-735 " استاندارد مهندسي بـراي طراحـي
دفـع و تصـفيه هايفرايندي سامانه
" ضايعات جامد كارخانه
Note 1:
This bilingual standard is a revised version of the
standard specification by the relevant technical
committee on Feb 2010, which is issued as
revision (1). Revision (0) of the said standard
specification is withdrawn.
:1 يادآوري
نه، نسخه بازنگري شده استاندارد فوق اين استاندارد دو زبا
توسط كميته فني 1388 ماه سالبهمن باشد كه در مي
از اين . گردد ارايه مي )1(مربوطه تاييد و به عنوان ويرايش
.باشد اين استاندارد منسوخ مي) 0(پس ويرايش
userUnderline
userUnderline
userUnderline
userUnderline
userUnderline
userUnderline
userUnderline
userUnderline
userUnderline
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
9
Note 2:
In case of conflict between Farsi and English
languages, English language shall govern.
: 2 يادآوري
در صورت اختالف بين متن فارسي و انگليسي، متن انگليسي
.باشد مالك مي
2. REFERENCES
Throughout this Standard the following dated
and undated standards/codes are referred to.
These referenced documents shall, to the extent
specified herein, form a part of this standard. For
dated references, the edition cited applies. The
applicability of changes in dated references that
occur after the cited date shall be mutually
agreed upon by the Company and the Vendor.
For undated references, the latest edition of the
referenced documents (including any
supplements and amendments) applies.
مراجع -2
ها و استانداردهاي تاريخ دار و در اين استاندارد به آيين نامه
اين مراجع، تا حدي كه در . بدون تاريخ زير اشاره شده است
اند، بخشي از اين اين استاندارد مورد استفاده قرار گرفته
در مراجع تاريخ دار، ويرايش . شوند استاندارد محسوب مي
تي كه بعد از تاريخ ويرايش در گفته شده مالك بوده و تغييرا
آنها داده شده است، پس از توافق بين كارفرما و فروشنده
در مراجع بدون تاريخ، آخرين ويرايش . باشد قابل اجرا مي
هاي آن مالك عمل آنها به انضمام كليه اصالحات و پيوست
.باشند مي
API (AMERICAN PETROLEUM INSTITUTE) API )اموسسه نفت آمريك(
API-RP-500A, "Recommended Practice for Classification of Locations for
Electrical installation at
petroleum facilitiesclassified
as Class I, Division I and
Division 2",2nd. Ed., November 1997
API-RP-500A " طبقهتجربيات توصيه شده براي
ب الكتريكي در هاي نصبندي محل
بندي شده طبقهتجهيزات نفتي
–2و قسمت 1 ، قسمت1دركالس
"1997 نوامبر -ويرايش دوم
API Publ. 421 "Management of Water Discharges, Design and
Operation of Oil-Water
Separators", 1st. Ed., 1990
API Publ. 421 " مديريت تخليه آب، طراحي و بهره
روغن، -هاي آباز جداكننده برداري
"1990ويرايش اول ،
API Std. 650 "Welded Steel Tanks for Oil
Storage"
API Std. 650 " مخازن فلزي جوشي براي ذخيره
"مواد نفتسازي
API Vol. 1 "Manual on Disposal of Refinery Wastes, Volume on
Liquid Wastes", 1969
API Vol.1 " ي،االيشگاهضايعات پدفع كتابچه
1969، "فصل ضايعات جامد
ASME (AMERICAN SOCIETY OF
MECHANICAL ENGINEERS)
ASME )مكانيك آمريكا انانجمن مهندس(
ASME Code, Section VIII, Div. 1 آيين نامه ASME ،قسمت VIII ،1 بخش
ASTM (AMERICAN SOCIETY FOR
TESTING AND MATERIALS)
ASTM ) آزمون و مواد آمريكاانجمن(
ASTM D-3921 "Test Method for Oil and Grease for Petroleum
Hydrocarbons in Water"
ASTM D-3921 " روش آزمايش براي روغن و
هاي نفتي يدروكربنهگريس براي
"در آب
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
10
DIN (DEUTSCHES INSTITUT FUR
NORMUNG)
DIN )استانداردهاي آلمان موسسه(
DIN 997 "Tracing Dimensions for Bars
and Rolled Steel Sections", Oct. 1970
DIN 997 "ها و ابعاد گرمكن براي ميله
شده، اكتبر نوردهاي فلزي قسمت
1970"
CEN (EUROPEAN COMMITTEE FOR
ELECTROTECHNICAL
STANDARDIZATION)
CEN )استاندارد سازي لوازم كميته اروپائي
)الكتروتكنيك
CEN 12255 “Waste Water Treatment
Plants-Part 13: Chemical
Treatment”
CEN 12255 " بخش –واحدهاي تصفيه پساب
"تصفيه شيميايي: 13
EPA (UNITED STATE ENVIRONMENTAL
PROTECTION AGENCY)
EPA )ياالت متحدهآژانس حفاظت از محيط زيست ا(
EPA-413.1 "Gravimetric Separation" EPA-413.1 "جداسازي ثقلي"
EPA-413.2 "Infrared
Spectrophotometry"
EPA-413.2 "طيف نورسنجي مادون قرمز"
EPA-160.2 "The Analysis of Total Suspended Solids
(Gravimetric) Dried at 103-
105◦C"
EPA-160.2 "همه ذرات جامد معلق تحليل
تا 103 خشك شده در) ثقلي(
"درجه سانتيگراد 105
IPS(IRANIAN PETROLEUM STANDARDS) IPS )استانداردهاي نفت ايران(
IPS-E-CE-380 "Engineering Standard for Sewerage and
Surface Water Drainage
System"
IPS-E-CE-380 " استاندارد مهندسي براي سامانه
و تخليه آب شبكه فاضالب
"سطحي
IPS-E-CE-390 "Engineering Standard for Rain & Foul Water
Drainage of Buildings"
IPS-E-CE-390 "آب استاندارد مهندسي براي
ان ساختمتخليه آلوده آب و باران
"ها
IPS-E-CE-400 "Engineering Standard for Sanitary Sewage
Treatment"
IPS-E-CE-400 " استاندارد مهندسي براي تصفيه
"فاضالب بهداشتي
IPS-E-GN-100 "Engineering Standard
for Units"
IPS-E-GN-100 " استاندارد مهندسي براي
"واحدها
IPS-E-PR-725 "Engineering Standard for Process Design of
Plant Waste Water
Sewer Systems"
IPS-E-PR-725 " استاندارد مهندسي براي طراحي
مجاري رايندي سامانه هاي ف
"فاضالب پساب كارخانه
IPS-E-PR-735 "Engineering Standard for Process Design of
IPS-E-PR-735 " استاندارد مهندسي براي طراحي
صفيه دفع و ت فرايندي سامانه هاي
userUnderline
userUnderline
userUnderline
userUnderline
userUnderline
userUnderline
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
11
Plant Solid Waste
Treatment & Disposal
Systems"
"ضايعات جامد كارخانه
IPS-G-SF-130 "General Standard for Disposal of Solid
Waste"
IPS-G-SF-130 " جامد دفعاستاندارد عمومي براي
" دور ريز
METCALF & EDDY, INC. * METCALF& EDDY, INC.
*
“Waste Water Engineering Treatment, Disposal,
and Reuse”, published by McGraw-Hill
Company, 4rd., Ed., 2003
، انتشارات "و استفاده مجدددفع ، تصفيه مهندسي پساب"
2003 -چهارم ويرايش McGraw-Hillشركت
* . TEXT BOOK كتاب*
3. DEFINITIONS AND TERMINOLOGY
For definition of the particular terms/words of
this Standard not outlined herein below,
reference should be made to the latest revision of
the following standards/publications:
تعاريف و واژگان - 3
و كلمه هاي خاص از اين استاندارد / براي تعاريف اصطالحات
نشريه /ستانداردكه در زير اشاره نشده، به آخرين ويرايش ا
.زير بايد رجوع شود
IPS-E-CE-380 "Engineering Standard for Sewerage and Surface Water
Drainage System"
IPS-E-CE-380 " استاندارد مهندسي براي سامانه
"و تخليه آب سطحيشبكه فاضالب
IPS-E-CE-390 "Engineering Standard for Rain & Foul Water Drainage
System"
IPS-E-CE-390 " استاندارد مهندسي براي آب باران و
"ساختمان هاتخليه آلودهآب
IPS-E-CE-400 "Engineering Standard for
Sewage Treatment "
IPS-E-CE-400 " استاندارد مهندسي براي تصفيه
"فاضالب بهداشتي
IPS-E-PR-725 "Engineering Standard for Process Design of Plant
Waste Water Sewer Systems"
IPS-E-PR-725 " استاندارد مهندسي براي طراحي
ي فاضالب مجار فرايندي سامانه هاي
"پساب كارخانه
3.1 Biochemical Oxygen Demand (BOD)
Biochemical oxygen demand (BOD) is oxygen
demand by microorganisms during stabilization
of organic matter under scribed conditions,
usually over a 5 day period, BOD5 specifically
denotes the oxygen demand over a 5 day period
at 20°C.
(BOD)اكسيژن بيوشيميايي مورد نياز 1- 3
اكسيژن بيوشيميايي مورد نياز ، نياز به اكسيژن توسط ريز
جاندارها طي پايدارسازي مواد آلي تحت شرايط تعيين شده
اختصاصا بر BOD5. عموماً طي يك دوره پنج روزه مي باشد
درجه 20روزه در دماي 5وره نياز اكسيژن طي يك د
.سانتيگراد داللت دارد
3.2 Chemical Oxygen Demand (COD)
Chemical oxygen demand (COD) is the equivalent amount of oxygen consumed under specified conditions in the chemical oxidation of the organic and oxidizable inorganic matter contained in a waste water, corrected for the influence of chlorides. In practice, unless otherwise specified, the chemical oxidizing agent is hot acid dichromate.
(COD) مورد نياز شيميايي اكسيژن 2- 3
مقدار معادل اكسيژن (COD)اكسيژن شيميايي مورد نياز
رف شده در شرايط مشخص در اكسايش شيميايي مواد مص
معدني قابل اكسايش و آلي كه در پسĤب وجود دارد، كه براي
در روش آمريكايي، به غير . تأثير كلريدها تصحيح شده است
شود، عامل اكسايش شيميايي دي از مواردي كه مشخص مي
.باشدكرومات اسيد گرم مي
userUnderline
userUnderline
userUnderline
userUnderline
userUnderline
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
12
3.3 Coagulant Aids
Materials added to enhance the action of
coagulants, generally by affecting the electrical
balance of the particles.
ها كمك منعقد كننده 3- 3
اضافه شده عمل انعقاد موادي هستند كه به منظور كمك به
.تغيير توازن الكتريكي ذرات عمل مي كنند باو بطور كلي
3.4 Coagulation and Coagulants
Coagulation is the formation of flocculate
particles from added chemical. Coagulants are
the materials added to the waste water to cause
agglomeration of small particles to facilitate their
separation.
انعقاد و منعقد كننده ها 4- 3 ه شده از مواد شيميايي اضافه شده را انعقاد تشكيل ذرات لخت
منعقد كننده ها موادي هستند كه براي ايجاد تراكم و . گويندانباشتگي ذرات كوچك به منظور كمك به جداسازي آنها به
.پساب اضافه مي شوند
3.5 Dissolved Oxygen (DO)
Dissolved Oxygen is the oxygen dissolved in
sewage, water or other liquid, usually expressed
in milligrams per liter (mg/l) or percent (%) of
saturation.
(DO) اكسيژن محلول 5- 3
مقدار اكسيژن حل شده در فاضالب ، آب يا ديگر مايعات
است كه معموال به صورت ميلي گرم در ليتر يا درصد اشباع
.بيان مي گردد
3.6 Effluent
Effluent is (1) a liquid which flows out of a
containing space, and/or (2) sewage, water or
other liquid, partially or completely treated, or in
its natural state, as the case be flowing out of a
reservoir, basin, or treatment plant, or part
thereof.
خروجي البفاض 6- 3
مايعي كه از ظرف حاوي ) 1(مواد خروجي عبارت است از
فاضالب، آب يا مايع ديگر، ) 2(يا /خود به خارج جريان يĤبد و
به صورت جزيي يا كلي تصفيه شود، يا در حالت طبيعي
خود، به عنوان مورد ممكن است از يك مخزن، حوضچه يا
.دواحد تصفيه يا بخشي از آن به بيرون جريان يĤب
3.7 Effluent Limitation
Effluent limitation is any restriction (including
schedules of compliance) established by a
governmental authority on quantities, rates and
concentration of chemical, physical, biological
and other constituents which are discharged from
point sources into navigable waters, the waters of
the contiguous zone, or the ocean.
خروجي فاضالب محدوديت 7- 3
از جمله برنامه (محدوديت مواد خروجي شامل هر محدوديت
وضع شده توسط مقامات دولتي در مقدار، ميزان و ) انطباق
يولوژيكي و ديگر مواد غلظت هاي مواد شيميايي، فيزيكي، ب
متشكله كه از منابع به آبهاي قĤبل كشتيراني، در آبهاي
.باشدمناطق همجوار يا اقيانوس ريخته مي شود، مي
3.8 Flocculation
The provision of retention time with gentle agitation to allow the floc particles or precipitate, associated with the impurities to increase in size by agglomeration.
لخته سازي 8- 3
در واقع فراهم كردن زمان نگهداري با هم زدن ماليم است
كه به ذرات لخته كننده امكان جمع شدن با ناخالصي ها و
.تشكيل توده هاي بزرگتر را مي دهد
3.9 Immediate Oxygen Demand (IOD)
Immediate Oxygen Demand (IOD) is the amount of oxygen that is utilized by the components of a waste water within 15 minutes (unless otherwise specified) after being introduced into water that contains dissolved oxygen.
(IOD) نياز فوري اكسيژن 9- 3
اكسيژن مصرفي توسط اجزاي نياز فوري اكسيژن، ميزان
) مگر غير از اين تعيين شود(دقيقه 15پسĤبي است كه طي
.باشد پس از وارد شدن به آبي كه حاوي اكسيژن محلول مي
3.10 Susceptibility to Separation (STS) Number
STS number is the oil contents in parts per million, of the suspend water after the specified settling period.
(STS)جداسازي قابليتعدد 10- 3
مقدار محتويات روغني معلق در آب بعد از زمان ته نشيني بر
.حسب جزء در ميليون مي باشد
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
13
3.11 Surface Water
Surface water is natural rain water from the
ground surface, paved areas and roofs plus
occasional courtyard and car washing waste
waters and incidental fire fighting water.
آب سطحي 11- 3
آب باران طبيعي جمع آوري شده از سطح زمين، منطقه
آسفالت، سقف ها و حياط و نيز آب شستشوي اتومبيل و آب
آتش نشاني مي باشد
3.12 Total Organic Carbon (TOC)
TOC is a measure of the amount of carbon in a
sample originating from organic matter only.
The test is run by burning the sample and
measuring the CO2 produced.
(TOC)كل كربن آلي 12- 3
TOC يك اندازه گيري از مقدار كربن در يك نمونه است كه
آزمايش با سوزاندن نمونه . اشدمنشاء آن فقط ماده آلي مي ب
.و اندازه گيري دي اكسيد كربن توليدي انجام مي شود
4. SYMBOLS AND ABBREVIATIONS
Symbols and abbreviations referred to in this
Standard are as follows:
نشانه ها و اختصارات - 4
ح زير ها و اختصارات ارجاع شده در اين استاندارد به شر نشانه
:مي باشند
SYMBOLS/ABBREVIATION DESCRIPTION توضيحات اختصارات/نشانه ها
ABS Acrylonitrile Butadiene Styrene. ABS آكريلو نيتريل بوتادين استايرن
BCME Bis (chloromethyl)ether. BCME بيس كلرومتيل اتر
BOD5 The 5 Day Biochemical Oxygen
Demand at 20°C.
BOD5 20در مورد نياز بيوشيميايي اكسيژن
روز 5درجه سانتي گراد در
CMME Methy chloromethyl methyl
ether.
CMME متي كلرومتيل متيل اتر
COD Chemical Oxygen Demand. COD مورد نياز شيميايي اكسيژن
CPI Corrugated Plate Interceptor. CPI دا كننده موج دارصفحه ج
DAF Dissolved Air Flotation. DAF هواي محلول يشناورساز
DEA di-Ethanolamine. DEA دي اتانول آمين
DGF Dissolved Gas Flotation DGF گاز محلول با شناورسازي
DN Diameter Nominal, in (mm). DN ميلي متر(قطر اسمي(
DO Dissolved Oxygen. DO اكسيژن محلول
DP Differential Pressure. DP اختالف فشار
EFF Efficiencies. EFF بازدهي
EPA Environmental Protection
Agency.
EPA آژانس حفاظت از محيط زيست
MBAC Methylene Blau Active
Substance.
MBAC ماده فعال متيلن بلو
MEA mono-Ethanolamine. MEA مونو اتانول آمين
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
14
MOCA 4,4’-methylene-bis (2-chloroaniline).
MOCA 4كلروآنيلين 2(متيلن بيس 4و(
MPN Maximum Possible Numbers. MPN حداكثر تعداد ممكن
OGP Oil, Gas and Petrochemical. OGP نفت، گاز و پتروشيمي
OSHA Occupational Safety and Health
Association.
OSHA انجمن سالمت و ايمني شغلي
PCBs Polychloro-biphenyls. PCBs پلي كلرو فنيل بنزن
PPI Parallel Plate Interceptor PPI تيغه هاي جداكننده موازي
ppm Parts per million. ppm قسمت در ميليون
PVC Poly-vinyl chloride. PVC پلي وينيل كلرايد
SS Suspended Solids. SS جامدات معلق
STS Suspectible To Separation. STS به جدا شدن محتمل
SWD Side Water Depth. SWD عمق آب كناري
TDS Total Dissolved Solids. TDS كل جامدات محلول
TOC Total Organic Carbon. TOC كل كربن آلي
USDA United States Department of
Agriculture.
USDA كشاورزي اياالت متحده اداره
USEPA United States Environmental
Protection Agency.
USEPA آژانس حفاظت محيط زيست اياالت
متحده
WPCF Water Pollution Control
Federation.
WPCF نترل آلودگي آباتحاديه ك
VOCs Volatile Organic Compounds. VOCs تركيبات آلي فرار
5. UNITS
This Standard is based on International System
of Units, (SI) as per IPS-E-GN-100, except
Where otherwise specified.
واحدها -5
، (SI)ستاندارد، برمبناي نظام بين المللي واحدها اين ا
باشد، مگر آنكه در مي GN-E-IPS-100منطبق با استاندارد
.متن استاندارد به واحد ديگري اشاره شده باشد
6. WASTE-WATER TREATMENT 6 - تصفيه پساب
6.1 Nature of Waste-Waters 6 -1 ماهيت پساب
Suspended solids, biodegradable organics,
nutrients, refractory organics, heavy metals,
dissolved inorganic solids oils and hydrocarbons
and pathogens are the important contaminants
which may be found in the OGP industry’s waste
waters. Appendix A presents a list of important
waste water contaminants and reasons for their
جامدات معلق، مواد آلي قابل تجزيه، ماده مغذي، مواد آلي
مقاوم، فلزات سنگين، روغن ها و ئيدروكربن هاي جامد غير
آلي محلول و عوامل بيماري زا از مهمترين آلودگي هايي
تند كه در پساب صنايع نفت، گاز و پتروشيمي يافت مي هس
از آلوده كننده هاي مهم پساب و فهرستي الفپيوست . شوند
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
15
TABLE 1 - GENERAL CLASSIFICATION OF WASTE WATER SOLIDS
بندي عمومي جامدات موجود در پساب طبقه – 1جدول
PARTICLE
CLASSIFICATION
دسته بندي ذرات
PARTICLE SIZE, mm
اندازه ذرات به ميليمتر
Dissolved لمحلو
Colloidal كلوئيدي
Suspended معلق
Settleable رسوب پذير
Supracolloidal فوق كلوئيدي
Less than 10-6
10-6كمتر از
10-6
to 10-3
10-3تا 10-6از
Greater than 10-3
10-3بزرگتر از
Greater than 10-1
10-1بزرگتر از
10-3
to 10-1
10-1تا 3-10
importance. داليل اهميت آنها را نشان مي دهد.
Suspended solids can be removed by physical
treatment in some extent. Removal of
biodegradable organics, suspended solids and
pathogens is achieved through the secondary
treatment operation Units. The more stringent
standards are dealt with the removal of nutrients
and priority pollutants (see Appendix B).When
waste water is to be reused, standards normally
include requirements for the removal of
refractory organics, heavy metals, and in some
case dissolved inorganic solids.
. تصفيه فيزيكي قابل حذف هستند تا حدي باجامدات معلق
حذف مواد آلي تجزيه پذير، جامدات معلق و عوامل بيماري زا
استانداردهاي . در واحدهاي تصفيه ثانويه قابل انجام است
دقيق تر با حذف مواد مغذي و آلوده كننده هاي داراي
لتي كه در حا .)را ببينيد بپيوست .( ارجحيت سروكار دارند
پساب مورد استفاده مجدد قرار مي گيرد، استانداردها داراي
الزاماتي براي حذف مواد آلي مقاوم ، فلزات سنگين و در
.محلول هستند معدنيبعضي موارد جامدات
6.1.1 Suspended solids
The standard way of testing a waste water for
suspended solids is to filter the waste water
through a 0.45 µm porosity filter. Anything on
the filter after drying at about 103°C is
considered a portion of the suspended solids.
Table 1 provides another classification system
for the solids found in waste water.
جامدات معلق 1- 1- 6
ستاندارد براي آزمايش وجود جامدات معلق در پساب، روش ا
. ميكرومتر است 45/0با تخلخل صاف عبور دادن آن از يك
103بعد از خشك شدن در دماي صاف مواد باقيمانده روي
يگراد بعنوان بخش جامدات معلق در نظر گرفته تدرجه سان
نوع ديگري از سامانه دسته بندي جامدات 1جدول . مي شود
.در پساب را عرضه مي كند موجود
6.1.2 Biodegradable organics
The following procedures shall be utilized to
estimate the oxygen-demanding potential of
waste waters:
مواد آلي تجزيه پذير 2- 1- 6
زير بايستي براي تخمين مقدار بالقوه هاي دستورالعمل
:اكسيژن مورد نياز در پساب استفاده گردد
- Biochemical Oxygen Demand
(BOD)Test.
(BOD)مورد نياز بيوشيميايي اكسيژن آزمون -
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
16
- Chemical Oxygen Demand (COD)
Test.
(COD)رد نياز موشيميايي اكسيژن ونآزم -
- Total Organic Carbon (TOC) Test. - كل كربن آلي ونآزم(TOC)
6.1.3 Heavy metals Any cation having an atomic mass (weight)
greater than 23 (atomic mass of sodium) to be
considered a heavy metal. See IPS-G-SF-130,
“Solid Waste Disposal” for levels of various
metals which are deemed permissible in fresh
water.
فلزات سنگين 3- 1- 6 جرم اتمي ( 23هر يون مثبت داراي جرم اتمي بيشتر از
.بعنوان يك فلز سنگين در نظر گرفته مي شود) سديمت مختلفي كه در براي فلزارا IPS-G-SF-130استاندارد
"جامد ضايعات دفع"با موضوع آب تازه مجاز فرض مي شوند .ببينيد
6.1.4 Dissolved inorganic solids
The following procedure can be used to
determine the inorganic dissolved solids in waste
waters. A sample of waste water to be filtered
through a 0.45 µm filter, collected the filtrate,
and vaporized first the water (at 103°C) and then
the organic fraction (at 550°C) from the filtrate.
The amount of material left in the vessel after
incineration at 550°C is referred to as the fixed
or inorganic dissolved solids level.
محلول معدنيجامدات 4- 1- 6
محلول معدني دستورالعمل زير براي تعيين مقدار جامدات
صاف يك نمونه از پساب از يك . در پساب قابل استفاده است
مايع صاف شده و ميكرومتر عبور داده شده 45/0با تخلخل
و درجه سانتيگراد 103دماي جمع آوري و در ابتدا آب در
جه سانتيگراد تبخير در 550در دماي آن سپس بخش آلي
پس از سوزاندن در مقدار مواد باقيمانده در ظرف. گرددمي
نشان دهنده ، سانتيگراد درجه 550دماي در آشغال سوز
.محلول خواهد بود معدنيجامدات ثابت مقدار
6.1.5 Toxic organic compounds
Appendix C provides some organics compounds
which are considered toxic and/or carcinogenic.
تركيبات آلي سمي 5- 1- 6
يا سرطان زا و بعضي تركيبات آلي كه سمي )ج(پيوست
.هستند را عرضه كرده است
6.1.6 Surfactants
Surfactants or surface-active agents, are large
organic molecules that are slightly soluble in
water and cause foaming in waste water
treatment plants and in the surface waters into
which the waste effluent is discharged. During
aeration of waste water, these compounds are
collected on the surface of the air bubbles and
thus create a very stable foam. The determination
of surfactants is accomplished by measuring the
color change in a standard solution of methylene
blue active substance (MBAS).
مواد فعال سطحي 6- 1- 6
مولكول هاي بزرگ يا ذرات فعال در سطح مواد فعال سطحي
آلي هستند كه اندكي محلول در آب بوده و در واحد تصفيه
به آنها خروجي دور ريز پساب و سطح آبهايي كه فاضالب
اين تركيبات در مرحله . تخليه مي شوند توليد كف مي كنند
شده و بنابراين هوادهي پساب در سطح حباب هاي هوا جمع
تعيين مقدار مواد . يك كف خيلي پايدار توليد مي كنند
سطحي فعال با اندازه گيري تغيير رنگ در محلول استاندارد
.ماده فعال متيلن بلو انجام مي گيرد
6.1.7 Priority pollutants
Priority pollutants (both inorganic and organic)
are selected on the basis of their known or
suspected carcinogenicity, mutagenicity,
teratogenicity, or high acute toxicity. Many of
the organic priority pollutants are also classified
as volatile organic compounds (VOCs).
Representative examples of the priority
pollutants are shown in Appendix B. Within a
مهمآالينده هاي 7- 1- 6
بر اساس رفتارهاي شناخته ) و آلي معدني( مهمآالينده هاي
سرطان زايي، جهش زايي، : ها كه عبارتند ازآن محتملشده يا
خيلي از . انتخاب مي شوند ،ا خيلي سمي بودنناقص زايي ي
ركيبات آلي فرار آلي همچنين در دسته ت مهمهاي هآاليند
در پيوست مهمهايي از نماينده آالينده هاي لمثا. قرار دارند
در يك سامانه جمع آوري و تصفيه . داده شده اند نشان ب
userUnderline
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
17
waste water collection and treatment system,
organic priority pollutants may be removed,
transformed, generated, or simply transported
through the system unchanged. Five primary
mechanical are involved; (1) volatilization (also
gas stripping); (2) degradation; (3) adsorption to
particles and sludge; (4) transporting through the
entire system; (5) generation as result of
chlorination or as byproducts of the degradation
of precursor compounds.
تغيير شكل و ممكن است حذف مهمپساب، آالينده هاي
داده شده ، گسترش پيدا كرده يا به سادگي در سامانه بدون
پنج عمليات مكانيكي اوليه درگير مي . تغيير باقي بمانند
تجزيه) 2( )همچنين جداسازي گاز( بخار شدن )1( :باشند
انتقال از ميان كل ) 4( ذب سطحي ذرات و لجنج) 3(
توليد در نتيجه كلردار كردن يا محصول جانبي ) 5( هنساما
پايهتجزيه تركيبات
6.1.8 Volatile organic compounds
Organic compounds that have a boiling point ≤ 100°C and/or a vapor pressure > 1 mm Hg (or
133.3 Pa ) at 25°C are generally considered to be
volatile organic compounds (VOCs), e.g., vinyl
chloride. The release of these compounds in
sewers and at treatment plants especially at the
headworks, is of particular concern with respect
to the health of collection system and treatment
plant workers.
تركيبات آلي فرار 8- 1- 6
بعضي تركيبات آلي مانند وينيل كلرايد كه نقطه جوش كمتر
ميليمتر 1درجه سانتيگراد يا فشار بخار بيش از 100از
ما بعنوان مواد آلي فرار يا دارند، عمو) پاسكال 133.3( جيوه
آزاد شدن اين مانند وينيل كلرايد . شناخته مي شوندسبك
ضالب و در واحد تصفيه بخصوص تركيبات در كانال هاي فا
به توجه ويژه اي در ارتباط با سالمتي اصليدر محل هاي
.افراد شاغل در سامانه جمع آوري و واحد تصفيه نياز دارد
6.2 Treatment Stages
Generally, the term “preliminary” and/or
“primary” referred to physical Unit operations;
“secondary “ referred to chemical and biological
Unit Processes; and “advanced” or “tertiary “
referred to combinations of all three.
مراحل تصفيه 2- 6
به عمليات واحد "اوليه"يا /و "ابتدايي"بطور كلي واژه
فيزيكي، ثانويه به فرايندهاي شيميايي يا ميكربي و پيشرفته
به تركيبي از هر سه عمليات فوق گفته مي مرحله يا سومين
.شود
Application and definition of the various stages
of treatment and methods to perform specific
functions are described in the following Articles.
انجامتعريف و كاربرد مراحل مختلف تصفيه و روش هاي
.در بندهاي زير تشريح شده است عمليات خاص
6.2.1 Preliminary waste water treatment
Preliminary waste water treatment is defined as
the removal of waste water constituents that may
cause maintenance or operational problems with
the treatment operations, processes, and ancillary
systems. Screening and comminution for the
removal of debris and rags, grit removal for the
elimination of coarse suspended matter that may
cause wear or clogging of equipment, and
floatation for the removal of large quantities of
oil and grease are examples of preliminary
operations.
پساب ابتداييتصفيه 1- 2- 6
حذف بعضي مواد تشكيل دهنده آن پساب، ابتداييتصفيه
است كه ممكن است موجب بروز مشكالت تعميراتي يا
عملياتي در مراحل تصفيه، فرايندها و سامانه هاي فرعي
:عبارت است از ابتداييمثال هايي از عمليات تصفيه . گردند
اجسام درشت ،غربال زني و خرد كردن براي حذف سنگ و
شن گير براي حذف مواد معلق درشت كه مي توانند باعث
براي حذف يشناورساز. سايش يا انسداد تجهيزات گردند
. گريسمقادير زياد روغن و
6.2.2 Primary waste water treatment
In primary treatment a portion of the suspended
solids and organic matter is removed from the
waste water. This removal is usually
accomplished with physical operations such as
screening and sedimentation.
تصفيه اوليه پساب 2- 2- 6 در تصفيه اوليه بخشي از جامدات معلق و مواد آلي از پساب
معموال توسط عمليات جداسازياين نوع . حذف مي گردند . و ته نشين سازي انجام مي گيرد كردنند غربال فيزيكي مان
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
18
The effluent from primary treatment will
ordinarily contain considerable organic matter
and will have a relatively high BOD. The
principal function of primary treatment will
continue to be as a precursor to secondary
treatment.
فاضالب خروجي از تصفيه اوليه معموال داراي مقدار قابل
بااليي خواهد "تانسب BODتوجهي از مواد آلي است و
)خوراك(پايه ماده ايجاداصلي تصفيه اوليه وظيفه. داشت
.براي تصفيه ثانويه خواهد بود
6.2.3 Conventional secondary waste water
treatment
Secondary treatment is directed principally
toward the removal biodegradable organics and
suspended solids. Disinfection is included
frequently in the definition of conventional
secondary treatment. Conventional secondary
treatment is defined as the combination of
processes customarily used for the removal of
these constituents and includes biological
treatment by activated sludge, fixed film
reactors, or lagoon systems and sedimentation.
تصفيه ثانويه متداول پساب 3- 2- 6
تصفيه ثانويه اصوال در ارتباط با جداسازي مواد آلي تجزيه
در بعضي موارد گندزدايي در . پذير و جامدات معلق است
تصفيه ثانويه متداول . تعريف تصفيه ثانويه متداول قرار دارد
بعنوان تركيبي از فرايندهاي عادي است كه براي حذف مواد
گيرد و شامل تصفيه رد استفاده قرار ميمتشكله پساب مو
ميكربي توسط لجن فعال، واكنش دهنده هاي با صفحه ثابت
.و ته نشيني است حوضچه سطحييا سامانه هاي
6.2.4 Nutrient removal or control
Nutrient removal or control is generally required
for:
حذف يا كنترل مواد مغذي 4- 2- 6
زير مورد نياز موارد رايكنترل مواد مغذي معموال ب حذف يا
:مي باشد
1) Discharges to confined bodies of water
where eutrophication may be caused or
accelerated;
تخليه محدود شده در جاهائي كه آب به محل هاي )1
مواد غذايي موجودات مي گردد موجب انباشتگي
.مي شوند در رشد آن تسريعيا ذره بيني
2) Discharges to flowing streams where
nitrification can tax oxygen resources or
where rooted aquatic plants can flourish;
جريانهايي كه نيتروژن دهي سبب كاهش تخليه به )2
و يا جائي كه گياهان آبزي ريشه دار شدهاكسيژن منابع
.رشد مي كنند
3) Recharge of ground waters that may be
used indirectly for public water supplies.
به تخليه مجدد به آبهاي زميني كه ممكن است )3
.يم براي مصارف آب عمومي استفاده شوندقغير مست طور
The nutrients of principal concern are nitrogen
and phosphors and may be removed by
biological , chemical, or a combination of these
processes. In many cases, the nutrient removal
processes are coupled with secondary treatment;
for example biological denitrification may
follow an activated sludge process that produces
a nitrified effluent.
كه ممكن استعبارتند از نيتروژن و فسفر مهممواد مغذي
يا تركيبي از آنها حذف و شيمياي بيولوژيكي، توسط فرايند
موارد فرايندهاي حذف مواد مغذي با از در بسياري . شوند
نيتروژن زداييبعنوان مثال . تصفيه ثانويه پيوسته است
د كه ي يك فرايند لجن فعال باشممكن است در پ بيولوژيكي
.كندنيتروژن دار توليد مي خروجيمواد
6.2.5 Advanced waste water treatment /waste
water reclamation
Advanced waste water treatment or tertiary
treatment is normally defined as the level of
treatment required beyond conventional
secondary treatment to remove constituents of
concern including nutrients, toxic compounds,
and increased amounts of organic material and
suspended solids. In addition to the nutrient
پساب احياءتصفيه پساب پيشرفته يا 5- 2- 6
معموال به سطحي از تصفيه پساب پيشرفته يا تصفيه سوم
از تصفيه ثانويه متداول براي تصفيه اطالق مي شود كه پس
حذف مواد تشكيل دهنده مانند مواد مغذي، تركيبات سمي
عالوه بر .و مقادير زياد مواد آلي و جامدات معلق مي باشد
مواد مغذي، عمليات واحد يا سلسله فرايندهاي حذف
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
19
removal processes, Unit operations or processes
frequently employed in advanced waste water
treatment are chemical coagulation, flocculation,
and sedimentation followed by filtration and
activated carbon. Less used processes include
ion exchange and reverse osmosis for specific
ion removal or for the reduction in dissolved
solids.
فرايندهايي كه در تصفيه پساب پيشرفته مورد استفاده قرار
انعقاد شيميايي، لخته سازي و ته : مي گيرند عبارتند از
. كردن و عبور از كربن فعالصاف نشيني و در پي آنها
يوني و اسمز كمتر شامل تبادل استفاده بافرايندهاي
حذف يون هاي خاص يا براي معكوس هستند كه براي
.كاهش جامدات محلول استفاده مي شوند
Advanced waste water treatment is also used in a
variety of reuse applications where a quality
water is required such as for industrial cooling
water and ground water recharge.
همچنين در تعدادي از كاربردهاي تصفيه پساب پيشرفته
استفاده مجدد مانند آب خنك كننده صنعتي و تغذيه آبهاي
زميني كه كيفيت خاصي از آب مورد نظر است استفاده مي
.شود
6.2.6 Toxic waste treatment/specific
contaminant removal
The removal of toxic substances and specific
contaminants is a complex subject and the
concentrations of toxic pollutants are usually
controlled by pretreatment prior to discharge to
the final treatment system. Many toxic
substances such as heavy metals are reduced by
some form of chemical-physical treatment such
as chemical coagulation, flocculation,
sedimentation, and filtration. Some degree of
removal is also accomplished by conventional
secondary treatment. Waste waters containing
volatile organic constituents may be treated by
air striping or by carbon adsorption. Small
concentrations of specific contaminants may be
removed by ion exchange. Table 2 presents a list
of typical pollutants that have an inhibitory
effect on the activated-sludge process.
حذف آلودگي خاص/سمي ضايعاتتصفيه 6- 2- 6
ص موضوع پيچيده اي حذف مواد سمي يا آلودگي هاي خا
بوده و غلظت آالينده هاي سمي معموال در يك پيش تصفيه
خيلي از . قبل از تخليه به سامانه تصفيه نهايي كنترل ميشوند
مواد سمي مانند فلزات سنگين توسط بعضي تصفيه هاي
فيزيكي مانند انعقاد شيميايي، لخته سازي، ته –شيميايي
همچنين . كنند كردن كاهش پيدا ميصاف نشيني، و
مقداري از حذف اين مواد توسط تصفيه ثانويه متداول انجام
پساب داراي مواد آلي فرار ممكن است بوسيله . مي گيرد
غلظت هاي . يا جذب كربني تصفيه گردد عاري سازي با هوا
يوني قابل حذف مي تبادلكم آالينده هاي خاص توسط
كه تاثير بازدارنده از نمونه آالينده ها فهرستي 2جدول .باشد
.روي فرايند لجن فعال دارند را نشان مي دهد
6.2.7 Sludge processing
For the most part, the methods and systems
reported in Table 3 are used to process the
sludge removed from the liquid portion of the
waste water.
فرآوري لجن 7- 2- 6
يشتر موارد، روش ها و سامانه هاي گزارش شده در در ب
شده از بخش مايع جداشدهبراي فرآوري لجن 3جدول
.پساب مورد استفاده قرار مي گيرند
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
20
TABLE 2 - THRESHOLD CONCENTRATIONS OF POLLUTANTS INHIBITORY TO THE
ACTIVATED-SLUDGE PROCESS
فرايند لجن فعال دره ها غلظت آاليندگي بازدارند آستانه – 2جدول
POLLUTANT
آالينده
CONCENTRATION, mg/L )ميلي گرم بر ليتر ( غلظت
CARBONACEOUS
REMOVAL
كربن دارمواد با حذف
NITRIFICATION دهي نيتروژن
Aluminum نيوميآلوم
Ammonia امونياك
Arsenic ارسنيك
(Borate (Boron تاروب
Cadmium كادميوم
Calcium كلسيم
(Chromium (hexavalent )زاوالنتهگ(كروميوم
(Chromium (trivalent )تري والنت(كروميوم
Copper مس
Cyanide سيانيد
Iron آهن
Manganese منگنز
Magnesium منيزيم
Mercury جيوه
Nickel نيكل
Silver ه نقر
Sulfate سولفات
Zinc روي
:Phenols :فنل ها
Phenol فنل
Cresol كرسول
Dinitrophenol 4-2 دي نيتروفنل 4و2
15-26 480 0.1
0.05-100 10-100 2500 1-10 50 1
0.1-5 1000
10
0.1-0.5 1-2.5
5
0.8-10 200
0.25
0.005-0.5 0.34
50
0.25
500
0.05-0.5
4-10
4-16 150
TABLE 3 - SLUDGE-PROCESSING AND DISPOSAL METHODS
دفعفرآوري لجن و روش هاي – 3جدول UNIT OPERATION, UNIT PROCESS, OR TREATMENT
METHOD عمليات واحد، فرايندهاي واحد يا روش تصفيه
FUNCTION عملكرد
Pumping
تلمبه كردنTransport of sludge and liquid biosolids
مايع بيوجامداتو لجن انتقال
Preliminary operations : اييابتد عمليات
Grinding خرد كردن
Particle size reduction
ذرات اندازه كاهشScreening
كردن غربال Removal of fibrous materials
فيبري مواد حذف Degritting
شن زدايي Grit removal
وماسه شن جداسازي Blending
اختالط Homogenization of solids streams
جامد هاي جريان سازي يكنواخت Storage
سازي ذخيره Flow equalization
جريان زييكسان سا
-
Feb 2010/ 1388بهمن
IPS-E-PR-730(1)
21
UNIT OPERATION, UNIT PROCESS, OR
TREATMENT METHOD يا روش تصفيه ،عمليات واحد، فرايند واحد
FUNCTION
عملكرد
:Thickening : سازي غليظت
Gravity thickening ثقلي سازي غليظ
Volume reduction
حجم كاهش Flotation thickening
سازي شناوربا سازي غليظ Volume reduction
حجم كاهشCentrifugation
يكزمر از گريزسازي غليظ Volume reduction
حجم كاهشGravity-belt thickening
اي تسمه – ثقلي سازي غليظ Volume reduction
حجم كاهشRotary-drum thickening
گردان زنخمبا سازي غليظVolume reduction
حجم كاهش
:Stabilization : تثبيت
Alkaline stabilization قليايي تثبيت
Alkaline stabilization قليايي تثبيت
Anaerobic digestion
هوازي يب تخمير Anaerobic digestion
هوازي بي تخمير
Aerobic digestion هوازي تخمير
Stabilization, mass reduction
جرم كاهش، تثبيت Autothermal aerobic digestion (ATAD)
(ATAD)حرارتي خود هوازي تخمير Stabilization, mass reduction
جرم كاهش، تثبيت Composting
كودسازي Stabilization, mass reduction
جرم كاهش، تثبيت
:Conditioning :اصالح
Chemical conditioning اصالح شيميايي
Improve dewaterability
بهبودي امكان آب گيري Other conditioning methods
ساير روش هاي اصالح Improve dewaterabi