IP Camera Setting Manual Star Light Series

Firmware Version V2.6

Thanks for purchasing our product. Before operating the unit, please read the instructions carefully and keep this manual for future reference.

The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without prior notice.

Table of Contents

1. INSTALLATION...................................................................................................................................................................... 1

1.1 INSTALLATION FLOW CHART ............................................................................................................................................... 1 1.2 DIRECT LINK...................................................................................................................................................................... 2 1.3 LINK VIA HUB / POE HUB .................................................................................................................................................... 2

2. USER INTERFACE ................................................................................................................................................................ 3

2.1 LOGIN ............................................................................................................................................................................... 3 2.2 INTERFACE OVERVIEW ....................................................................................................................................................... 4

1. Live View ............................................................................................................................................... 5

2. Video ..................................................................................................................................................... 6

3. Image .................................................................................................................................................... 8

4. Audio ..................................................................................................................................................... 9

5. DateTime ............................................................................................................................................. 10

6. Network ................................................................................................................................................11

7. Alarm ................................................................................................................................................... 13

8. Face Detection ..................................................................................................................................... 14

9. Storage ................................................................................................................................................ 16

10. Maintain ............................................................................................................................................... 17

11. PTZ/OSD ............................................................................................................................................. 18

130820-STAR UI-V2.6-V1 1

1. Installation

1.1 Installation Flow Chart

Default Settings of IP CAM IP Address : 192.168.1.168 User Name : admin Password : 9999

Suggested IP Address For PC/NB IP Address : 192.168.1.200 Subnet Mask : 255.255.255.0 Gateway : 192.168.1.1

NOTE: Use PoE device for power supply is only available to cameras with PoE function. Cameras without PoE function need to be connected directly to the power supply.

Power Type DC

Check the power of PoE Plug the Power Adapter

Connect the RJ-45 LAN cable to the IP CAM

PoE

IP setting for PC/NB (Please see the suggested IP address)

Disable the anti-virus software and firewall

Turn on the PC/NB and log-in Windows OS

Run IE browser (IE 8.0 or above)

Type the URL http://192.168.1.168 and get into IP CAM setting window

FINISH

Get into the IP CAM setting window

User Name: admin / Password: 9999

Make sure PC installed with JAVA Version 6

Update 27 or above when installing IP CAM for the

first time

START

130820-STAR UI-V2.6-V1 2

1.2 Direct Link

Make sure PC installed with JAVA Version 6 Update 27 or above (1) Plug the power adapter to IP CAM. (2) Run the IE browser with http://192.168.1.168 (3) When the log-in window pop-up, please input the User Name and Password. (4) Whenever the connection is ready, the main page (setting window) of IP CAM will show

on.

1.3 Link via Hub / PoE Hub (“Link via PoE Hub” applied only to models with PoE function)

Make sure PC installed with JAVA Version 6 Update 27 or above

(1) Run the IE browser with http://192.168.1.168 (2) When the log-in window pop-up, please input the User Name and Password. (3) Whenever the connection is ready, the main page (setting window) of IP CAM will show

on.

Adapter

Cat-5 LAN cable

PoE / Hub

Cat-5 LAN cable Cat-5 LAN cable

130820-STAR UI-V2.6-V1 3

2. USER INTERFACE

2.1 Login

1. Start the browser, and input http://192.168.1.168/ in the address field, then press Enter.

NOTE:

It is strongly suggested that the user browse with Internet Explorer. Browsers other than Internet Explorer are NOT fully supported when the manual published, hence, the manufacturer WILL NOT BE LIABLE FOR ANY LOSS OR DAMAGE CAUSED.

2. Enter User Name and Password In the prompt window, and click OK.

The default User Name and Password is admin and 9999. You will need to enter the account and password every time whenever you restart the application or reconnect.

130820-STAR UI-V2.6-V1 4

2.2 Interface Overview

After login to the system, the screen will be displayed as below:

On the left side are the buttons of the function pages. The functions each page performs are listed in the table below. More information will be given in the following sections. Whenever the adjustment completed, click Submit to save the settings.

Note：

The content of the function pages may vary by model.

Live View

Video

Image

Audio

DateTime

Network

Alarm

Storage

Maintain

PTZ/OSD

130820-STAR UI-V2.6-V1 5

1. Live View

Main page. Display the image captured by the camera.

Language:

English / 日本语 / 繁中 / 简体中文 / Россия / Magyar / Deutsch /

رانا España / Polska / Nederlands / Portuguese / Francais / ي

(Language options may vary by region)

Full Screen

Zoom in

Snapshot

Zoom out

Record & Save

Restore

Stop Recording

Information

Motion Detect

Audio On

Audio Off

Face Detect

PTZ Control (Applied only to models with PTZ function):

Stop (center button) / 8-direction Keys (outer buttons)

Zoom Out Zoom In

Wide Tele

130820-STAR UI-V2.6-V1 6

2. Video Modify the settings of IP video settings, stream type and local display.

Shutter / Quality / IRIS

Shutter Speed (Min)(Second)

1/2, 1/4, 1/8, 1/15, 1/25(PAL), 1/30(NTSC), 1/50(PAL), 1/60(NTSC), 1/100(PAL), 1/120(NTSC), 1/250, 1/500, 1/750, 1/1,000, 1/1,500, 1/2,000, 1/10,000, 1/100,000 sec.

Shutter Speed (Max)(Second) 1/30, 1/60, 1/120, 1/250, 1/500, 1/750, 1/1000, 1/1500, 1/2000, 1/10000, 1/100000

Shutter Speed (Level) 0~7

Quality (Level) 0~7

Auto IRIS Manual / Auto

FLC / WB / BLC

Flicker Control 60hz NTSC / 50hz PAL

White Balance AUTO_WIDE / AUTO_NORMAL / SUNNY / SHADOW / INDOOR / LAMP / FL1 / FL2

Back Light Compensation Off / On

Back Light Level Min / Mid / Max

WDR / IR-Cut

WDR Enhancement Off / On

WDR Level 0~7

IR-Cut Setting Auto / BW / Color / External

DNR OFF / 2D DNR / 3D DNR

Sensor Mode LINEAR / WDR

With WDR mode, Shutter Speed Max can only set to 1/250.

130820-STAR UI-V2.6-V1 7

Stream Type

Video Streams Single / Dual / Tri-stream

Face Detection is only available with Single video streams.

Codec Profiles H.264 / MPEG4 / MegaPixel JPEG

Resolution H.264: 720P(1M), H.264: D1, H.264: SXGA(1.3M), H.264:1080P(2M), H.264: 3M

Stream1 M-JPEG Frame rate 1 / 3 / 5 / 10 / 15 / 20 / 25 / 30 fps

Quality 25 / 50 / 75 (NOTE: The content may vary by model)

130820-STAR UI-V2.6-V1 8

3. Image

Modify the settings of image, OSD and advanced image settings.

Image Brightness 0 ~ 255 (Default 128)

Contrast 0 ~ 255 (Default 128)

Saturation 0 ~ 255 (Default 128)

Sharpness 0 ~ 255 (Default 128)

DeNoise 0 ~ 255 (Default 128)

EV Compensation 0 ~ 255 (Default 128)

GrayScale 0 ~ 255 (Default 128)

Default Restore to the default values

ReLoad Load the previous values

Stream1 / Stream2 / Stream3 OSD Mode Date / Time / Text

Text Position Top-Left / Top-Right

Local Display

Date Position Bottom-Right / Bottom-Left

Time Position Bottom-Right / Bottom-Left

Local Display OFF / NTSC / PAL

Rotation OFF / HORIZONTAL / VERTICAL / BOTH

Size 5 sec / 10 sec

Format H.264 (1920 x 1080)

130820-STAR UI-V2.6-V1 9

4. Audio Modify the settings of audio.

Audio Enable Audio Enable / Disable

Audio Mode MIC / SPEAKER / BOTH

Input volume 0~100

Sample Rate/Bitrate 8Khz/64Kbps / 16Khz/128Kbps

Output Volume 0~100

(NOTE: The content may vary by model)

130820-STAR UI-V2.6-V1 10

5. DateTime

Modify the settings of date and time.

DateTime TimeZone Select the time zone

Day light Enable / Disable

Set Manual Date / Time Manual set the date and time

Sync Current PC Date / Time Synchronization the date and time with current PC

Sync with SNTP Server Synchronization the date and time with SNTP Server

Date Format Select the format of date

Time Format Select the format of time

130820-STAR UI-V2.6-V1 11

6. Network Modify the settings of network and IP address.

DHCP / Static IP / PPPoE Use DHCP Select to use DHCP for connection

Static IP Select to use static IP for connection

IP Address Domain name of IP address

Mask Domain name of mask

Gateway Domain name of gateway

DNS Domain name of DNS

PPPoE Select to use PPPoE for connection

Account Enter account

Password Enter password

Multicast Enable Multicast Enable / Disable

H264 Main / Sub Port Communication port for H.264

MPEG4 Main / Sub Port Communication port for MPEG4

MJPEG Port Communication port for M-JPEG

130820-STAR UI-V2.6-V1 12

SMTP SMTP Auth Enable / Disable SMTP authentication

Account Enter account

Password Enter password

Sender Assign mail address of Sender

Server Domain name of SMTP server

Mail list List of mail account

FTP Server FTP Server Domain name of FTP server

Port 21

Account Enter account

Password Enter password

Upload Path Assign upload path

DDNS DDNS Enable / Disable

Domain Domain name of DDNS server

Account Enter account

Password Enter password

Service DDNS service provider

Http / Onvif Http Port Domain name of HTTP port

OnvifPort 8080 (Using Onvif must sync PC time)

SNTP Server SNTP Server Domain name of SNTP server

SNMP Server SNMP Server Domain name of SNTP server

130820-STAR UI-V2.6-V1 13

7. Alarm

Modify the settings of alarm trigger and actions.

Alarm Enable Alarm Enable / Disable

Alarm Duration The duration of alarm

Alarm Trigger Motion Motion trigger alarm (None support for single M-JPEG)

Ethernet Lost Trigger alarm on Ethernet loss

DI1 Mode Trigger mode for DI

DI1 Level Alarm level of DI

Face Detect Advanced Set

Click to enter the sub menu for further settings.

To activate Face Detect Advanced Set, make sure the video streams is set to Single. (Refer to the section of Video.)

Alarm Action Upload via FTP Upload via FTP on receiving alarm signal

Upload via SMTP Upload via SMTP on receiving alarm signal

Local Storage Save Save to local storage on receiving alarm signal

Play Sound Play sound on receiving alarm signal (Need to enable Speaker in Audio Mode)

DO1 Mode Trigger mode for DO

DO1 Level Alarm level of DO

130820-STAR UI-V2.6-V1 14

8. Face Detection Modify the settings of face detection settings.

Face Detection Sub Menu

Face Detect Off / On

Set On to enable Face Detect function.

Fdx Axis

0~1280

The default is 0, the largest detection area (whole screen). To narrow down the detection area, add the value by dragging the bar or click on +/- icon.

Fdy Axis

0~960 The default is 0, the largest detection area (whole screen). To narrow down the detection area, add the value by dragging the bar or click on +/- icon.

FdConfLevel

0~75

The default is 75, the highest detection sensitivity. To decrease the detection sensitivity, subtract the value by dragging the bar or click on +/- icon.

Reload Load the previous values

Fd Direction

UP / LEFT / RIGHT

The default is UP, the normal upward direction. To change the detection direction, switch to LEFT (counterclockwise) or RIGHT(clockwise).

130820-STAR UI-V2.6-V1 15

Check the settings in the preview window.

Check the face detection function in Live View page. If the face detection function is on, Face Detect icon will be flashing and the snapshots will be automatically saved to the assigned folder every 30 seconds.

130820-STAR UI-V2.6-V1 16

9. Storage Modify the settings of storage and files upload.

Storage Upload via FTP File format for upload via FTP

Local Storage Save File format for save files

Schedule Set the storage schedule time of a week

130820-STAR UI-V2.6-V1 17

10. Maintain

Maintain the user name, password and update the firmware.

Maintain Current Version Current version of the firmware

Mac Address Mac address assigned by production

Firmware Update Browse and select the firmware downloaded from official site, and click Update to update the firmware

IP CAM Restart Reboot this IP camera after firmware updated

Snapshot Record Folder Click select to select a folder to save snapshots and real-time recording data

Name / Password Change the login User Name and Password

Authority Change the authority level of users

User List User list of this IP camera

Add / Del User Add / Delete the user

Log List Login list of this IP camera

SD format Format the SD in use

130820-STAR UI-V2.6-V1 18

11. PTZ/OSD Define the commands of PTZ (Pan/Tile/Zoom)/OSD. The default protocol is Pelco D and Pelco P. Use protocols other than Pelco D and Pelco P, define the commands in the field of Customize.

General Full Screen PTZ Enable / Disable Full Screen PTZ

ID 0~255

Baud 1200 / 2400 / 4800 / 9600 / 19200 / 38400 / 57600 / 115200

Pelco D / Pelco P

Zoom 0~3

Pan 0~63

Tilt 0~63

Customer

Stop

Up / Down

Left / Right

Zoom in / Zoom out

Wide / Tele

SET: Create and define commands