Invacare 9000 Series user Manual

7/26/2019 Invacare 9000 Series user Manual

1/88

Service Manual

DEALER:Keep this manual. The procedures in this manual must beperformed by a qualified technician only.

For more information regarding

Invacare products, parts, and services,

please visit www.invacare.com

9000 Series

9000 SL

9000 XT

9000 XDT

9000XT Recliner


2/88

REFERENCE DOCUMENTS

9000 Series 2 Part No. 1076155

WARNINGTHE PROCEDURES IN THIS SERVICE MANUAL MUST BE

PERFORMED BY A QUALIFIED TECHNICIAN.

DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT

FIRST READING AND UNDERSTANDING (1) THE OWNERSOPERATOR AND MAINTENANCE MANUAL AND (2) THE SERVICE

MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE

WARNINGS, CAUTIONS AND INSTRUCTIONS, CONTACT

INVACARE TECHNICAL SUPPORT BEFORE ATTEMPTING TO

SERVICE OR OPERATE THIS EQUIPMENT. OTHERWISE, INJURY

OR DAMAGE MAY RESULT.

REFERENCE DOCUMENTSRefertothetablebelowforpartnumbersofadditionaldocumentswhicharereferencedinthismanual.

MANUAL PART NUMBER

9000 Series Owners Operator and Maintenance Manual 1056953

NOTE:Updatedversionsofthismanualareavailableonwww.invacare.com.


3/88

TABLE OF CONTENTS

Part No. 1076155 3 9000 Series

TABLE OF CONTENTSREFERENCE DOCUMENTS ................................................................. 2

SPECIAL NOTES ................................................................................ 6

LABEL LOCATION ............................................................................ 7

TYPICAL PRODUCT PARAMETERS .................................................... 8SECTION 1GENERAL GUIDELINES ................................................. 12

Stability - All Models ................................................................................................................................12

Stability - Recliner Models Only.......................................................................................................13

Anti-Tippers...............................................................................................................................................13

Operating Information.............................................................................................................................13

Tire Pressure.............................................................................................................................................14

Weight Training ........................................................................................................................................14

Weight Limitation.....................................................................................................................................14

SECTION 2SAFETY INSPECTION/TROUBLESHOOTING .................... 15

Checklist.....................................................................................................................................................15

Troubleshooting .............................................................................................................16

Maintenance...............................................................................................................................................16

Maintenance Safety Precautions .......................................................................................................16Suggested Maintenance Procedures ................................................................................................16

SECTION 3SEAT AND BACK ......................................................... 18

Adjusting Back Angle ...............................................................................................................................18

Adjusting Back Height..............................................................................................................................19

9000 SL without Adjustable Back Angle Option ..........................................................................199000 SL with Adjustable Back Angle Option and 9000 XT/XDT ............................................20

Adjusting Seat Width...............................................................................................................................20

Adjusting Seat Depth...............................................................................................................................23

9000XT Model......................................................................................................................................239000 XDT and 9000 SL......................................................................................................................24

SECTION 4FRONT CASTERS ......................................................... 26

Front Caster Mounting Adjustments...................................................................................................26

Converting from Trailing to Leading or Leading to Trailing Casters...........................................27

Repositioning/Replacing Cam.................................................................................................................28

SECTION 5SEAT TO FLOOR ........................................................... 29

Changing Seat-to-Floor Height/Seat-to-Floor Angle........................................................................29

Super Low Frame Style.......................................................................................................................31Adult/Tall Frame Style.........................................................................................................................31Adult/Hemi Frame Styles ...................................................................................................................32


4/88

TABLE OF CONTENTS


TABLE OF CONTENTS24-Inch Rear Wheels and 8-Inch Front Casters .....................................................................3224-Inch Rear Wheels and 6-Inch Front Casters .....................................................................3722-Inch Rear Wheels and 8-Inch Front Casters .....................................................................3922-Inch Rear Wheels and 6-Inch Front Casters .....................................................................43

20-Inch Rear Wheels and 8-Inch Front Casters .....................................................................4620-Inch Rear Wheels and 6-Inch Front Casters .....................................................................48

SECTION 6REAR WHEELS ............................................................. 52

Removing/Installing Rear Wheels .........................................................................................................52

Quick-Release Axles ...........................................................................................................................52Permanent Axles..................................................................................................................................53

Models without Offset Axle Option ..........................................................................................53Models with Offset Axle Option ................................................................................................54

Adjusting Quick-Release Axle ...............................................................................................................57

Adjusting Wheelbase Length .................................................................................................................57SECTION 7RECLINER ................................................................... 58

Replacing Release Handle .......................................................................................................................58

Adjusting Cable Assembly Tension ......................................................................................................59

Replacing Cable Assembly......................................................................................................................60

Disconnecting/Connecting Lower Cable Assembly .........................................................................61

Disconnecting .......................................................................................................................................61Connecting ............................................................................................................................................61

Replacing Threaded Sector ....................................................................................................................64

Replacing Locking Rod ............................................................................................................................65Replacing Back Tube................................................................................................................................65

Removing/Installing Spring Lift Mechanism .........................................................................................67

Removing ...............................................................................................................................................67Installing..................................................................................................................................................68

Replacing Recliner Tube..........................................................................................................................69

Adjusting Seat Width...............................................................................................................................71

Adjusting Seat Depth...............................................................................................................................74

Removing/Installing Rear Wheels .........................................................................................................75

With Patient Operated Wheel Locks.............................................................................................75With Attendant Operated Wheel Locks .......................................................................................75

Using/Adjusting Wheel Locks................................................................................................................75

Using Attendant Operated Wheel Locks.......................................................................................75Adjusting Attendant Operated Wheel Locks................................................................................76

Changing Seat-to-Floor Height..............................................................................................................77

Installing Anti-Tippers..............................................................................................................................78


5/88


SECTION 8ANTI-TIPPERS/WHEEL LOCKS ....................................... 80

Installing/Adjusting Anti-tippers ............................................................................................................80

Installing Anti-Tippers .........................................................................................................................80Adjusting Anti-Tippers........................................................................................................................81

Using/Adjusting Disk Wheel Locks ......................................................................................................82

Using Patient Operated Disk Wheel Locks...................................................................................82Adjusting Patient-Operated Wheel Locks .....................................................................................83

Installing Wheel Lock Shoe Extensions...............................................................................................85

LIMITED WARRANTY ..................................................................... 87


6/88

SPECIAL NOTES


SPECIAL NOTESSignalwordsareusedinthismanualandapplytohazardsorunsafepracticeswhichcouldresultinpersonalinjuryorpropertydamage.Refertothefollowingtablefordefinitionsofthesignalwords.

NOTICE

THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO

CHANGE WITHOUT NOTICE.WHEELCHAIR USER

As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety of

wheelchairs to meet many needs of the end user. However, final selection of thetype of wheelchair to be used by an individual rests solely with the user and his/herhealthcare professional capable of making such a selection.

WHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT RESTRAINTS

Wheelchair users should NOT be transported in vehicles of any kind while in

wheelchairs. As of this date, the Department of Transportation has not approvedany tie-down systems for transportation of a user while in a wheelchair, in a moving

vehicle of any type.It is Invacares position that users of wheelchairs should be transferred into

appropriate seating in vehicles for transportation and use be made of the restraintsmade available by the auto industry. Invacare cannot and does not recommend any

wheelchair transportation systems.

SEAT POSITIONING STRAP

Regarding seat positioning straps, it is the obligation of the DME dealer, therapists

and other healthcare professionals to determine if a seat positioning strap isrequired to ensure the safe operation of this equipment by the user. Serious injurycan occur in the event of a fall from a wheelchair.

SIGNAL WORD MEANING

DANGER Danger indicates an imminently hazardous situation which, if not avoided, will result indeath or serious injury.

WARNING Warning indicates a potentially hazardous situation which, if not avoided, could result indeath or serious injury.

CAUTION Caution indicates a potentially hazardous situation which, if not avoided, may result inproperty damage.


7/88

LABEL LOCATION


IMPORTANT NOTICE

The wheel locks on this wheelchair have been

pre-set at the factory to comply with theVeterans Admini strati on functi onal Standard

8320.01 of the Federal Register, paragraph3.2.4.5.3. If these wheel locks do not meet

your needs, follow instructions below.

! CAUTION

Any wheel lock adjustments should embed

wheel lock shoe at least 1/8" into tire whenlocked (3/16" on pneumatic tires).

INSTRUCTIONS FOR WHEEL

LOCK ADJUSTMENTS

1. Loosen wheel lock mounting fastener,which runs through mounting bracket and

frame.2. Slide clamp toward rear wheel until wheel

lock shoe is embedded into tire material atleast 1/8" when handle is engaged to the

lock position (3/16" for pneumatic tires).3. Tighten mounting fastener to secure

mounting bracket in desired location andrecheck lock shoe embedding.

4. Inspect for correct locking action BEFORE

actual use.00078X021-0394

Refer to Owner's Manual

for proper anti-tipper

setting. 1085379

WARNING

WARNINGDETENT BALLS MUST BE SECURE-

LY SEATED IN RECESSED AREAS

OF AXLE BUSHINGS. ENSURE

THAT PLUNGER PIN IN HEAD END

OF AXLE IS FULLY RELEASED.

KEEP DETENT BALLS CLEAN.

1001948

CAUTION

DO NOT recline without occupant. When the

chair is not occupied the back will raise abrup-

tly. Keep clear of the chair back when raising

or lowering to avoid injury.1023096

CAUTIONSERVICE OF SPRING

LIFT MECHANISM TO

BE PERFORMED BY

PROPERLY TRAINED

AUTHORIZED SERVICE

PERSONNEL ONLY.

1022642

WARNINGDO NOT OPERATE WITHOUT

THE ANTI-TIP TUBES

INSTALLED.REV. 5/98 P/N 60106X144

WARNINGDO NOT OPERATE WITHOUT

THE ANTI-TIP TUBES

INSTALLED.REV. 5/98 P/N 60106X144

LABEL LOCATIONCrossmember

Lower

Frame

Tube

9000 XDT Only

NOTE:Onalladjustableantitippers

9000 XT Recliner Models Only

Models with

Quick-Release Axles Only


8/88

TYPICAL PRODUCT PARAMETERS



*NOTE:Theseoptionsarestandardforthismodel.

**NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.Theseheightscanvary+/ inchduetotirewearandmanufacturingtolerances.

9000 SL

OVERALL WIDTH 23 or 25 inches

OVERALL DEPTH (WITH RIGGINGS) 43 inches

SEAT WIDTH 16, 18 or 20 inches

SEAT DEPTH 16 or 18 inches

** SEAT-TO-FLOOR

TALL/ADULT:ADULT/HEMI:SUPER HEMI:

N/A15 to 19 in 1-inch incrementsN/A

BACK STYLE Sectional* - height adjustable in 1-inch incrementsAdjustable angle - 85 to 110 in 5 increments

BACK HEIGHT Ranges of 15 to 17 inches or 17 to 19 inches(adjustable in 1-inch increments)

ARM STYLES Swing Back* Space Saver*, Desk* or full length in

Fixed* or Adjustable HeightSwing Back Removable, Conventional, AdjustableHeight (Adjustable back angle style)

FRONT RIGGINGS Swingaway footrests and elevating legrests

REAR AXLE Permanent* and quick-release

REAR WHEELS 20, 22 and 24*-inch composite; Urethane*, pneumaticor pneumatic-flat free insert

HANDRIMS Composite* and aluminum, steel

WHEEL LOCKS Toggle lock -push or pull

CASTER SIZE 6 x 1-inch Urethane, 8 x 1-inch* Urethane,

8x1-inch solid rubber, and 8x1-inch pneumatic orpneumatic flat-free insert

UPHOLSTERY Black nylon*, black vinyl

FRAME COLORS Chrome* and colors

WEIGHT (18 X 16 INCH SEAT) 33 lbs

SHIPPING WEIGHT (APPROX.)

16 X 16 INCH SEAT FRAME WITH COMPLETEPACKAGE:

43 lbs

WEIGHT LIMIT 250 lbs (114 kg)


9/88




**NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.

Theseheights

can

vary

+/

inch

due

to

tire

wear

and

manufacturing

tolerances.

9000 XT

OVERALL WIDTH 21, 22, 23, 25, 27 or 29 inches


SEAT WIDTH 14, 15, 16, 18, 20 or 22 inches

SEAT DEPTH 16, 17, or 18 inches

** SEAT-TO-FLOOR


N/A15 to 19 in 1-inch increments13 and 14 inches

BACK STYLE Height adjustable* - 1-inch incrementsAdjustable angle - 85 to 110 in 5 increments


ARM STYLES Swing back removable, space saver* or conventionalin desk* or full length and in fixed* or adjustableheight


REAR AXLE Permanent* and quick-release


HANDRIMS Composite*, aluminum, steel and plastic coated

WHEEL LOCKS Toggle lock -push or pull

CASTER SIZE 6 x 1-inch Urethane, 8 x 1-inch* Urethane,8x1-inch solid rubber, and 8x1-inch pneumatic orpneumatic flat-free insert, 8x1-inch semi pneumatic

UPHOLSTERY Black nylon*, black sail cloth, heavy vinyl

FRAME COLORS Chrome* and colors

WEIGHT (18 X 16 INCH SEAT) 31 lbs

SHIPPING WEIGHT (APPROX.)

16 X 16 INCH SEAT FRAME WITH COMPLETEPACKAGE

41 lbs



10/88


9000 Series 10 Part No. 1076155


**NOTE:Theseattofloorheightsarebasedonpneumatictiresandpneumatictireswithflatfreeinserts.Ifwheelchairisequippedwithurethanetires,subtractinchfromthemeasurementslistedabove.Allheightsaremeasuredwithproperlyinflatednewtires.Theseheightscanvary+inchduetotirewear.

9000 XT RECLINER

OVERALL WIDTH 23, 25, 27, 28, 29 or 31 inches


SEAT WIDTH 14, 16, 18, 19, 20 or 22 inches

SEAT DEPTH 16, 17, or 18 inches

SEAT-TO-FLOOR**


17 to 19 inches in 1-inch incrementsN/AN/A

BACK STYLE Reclining

BACK HEIGHT 23 or 24 inches

ARM STYLES ConventionalDesk* or full length and in fixed* or adjustable height


REAR AXLE Permanent


HANDRIMS Composite*, aluminum, steel and plastic coated

WHEEL LOCKS Toggle lock - push or pull

CASTER SIZE 8 x 1-inch* Urethane, 8x1-inch solid rubber, and8x1-inch pneumatic or pneumatic flat-free insert,8x1-inch semi pneumatic

UPHOLSTERY Heavy vinyl, light vinyl, nylon, sail cloth

FRAME COLORS Chrome and colors

WEIGHT 50 lbs

SHIPPING WEIGHT (APPROX.) 60 lbs18x17-inch seat frame with complete package



11/88


Part No. 1076155 11 9000 Series


**NOTE:Theseattofloorheightsarebasedonpneumatictiresandpneumatictireswithflatfreeinserts.Ifwheelchairisequippedwithurethanetires,subtractinchfromthemeasurementslistedabove.Allheightsaremeasuredwithproperlyinflatednewtires.Theseheightscanvary+

inch

due

to

tire

wear.

9000 XDT

OVERALL WIDTH 23, 25, 27 or 29 inches


SEAT WIDTH 16, 18, 20 or 22 inches

SEAT DEPTH 16, 17, 18, 19 and 20 inches

SEAT-TO-FLOOR**


17, 19 and 21 inchesN/AN/A

BACK STYLE Height adjustable - 1-inch increments


ARM STYLES Swing back or removable, space saver* or conven-tional, desk* or full length and in fixed* or adjustableheight


REAR AXLE Permanent

REAR WHEELS 24*-inch composite, urethane*, pneumatic or pneu-matic-flat free insert

HANDRIMS Steel*, aluminum and plastic coated

WHEEL LOCKS Toggle lock - push or pull

CASTER SIZE 8 x 1-inch* Urethane, 8x1-inch solid rubber, and8x1-inch pneumatic or pneumatic flat-free insert,8x1-inch semi pneumatic

UPHOLSTERY Black nylon, black sail cloth, heavy vinyl

FRAME COLORS Chrome and colors

WEIGHT 36 lbs

SHIPPING WEIGHT (APPROX.) 46 lbs16x16-inch seat frame with complete package



12/88

SECTION 1GENERAL GUIDELINES

9000 Series 12 Part No. 1076155


WARNINGSECTION 1 - GENERAL GUIDELINES contains important information for the safe

operation and use of this product.DO NOT use this product or any available

optional equipment without first completely reading and understanding theseinstructions and any additional instructional material such as Owners Manuals,Service Manuals or Instruction Sheets supplied with this product or optionalequipment. If you are unable to understand the Warnings, Cautions or Instructions,

contact a healthcare professional, dealer or technical personnel before attemptingto use this equipment. Otherwise, injury or damage may occur.

Stability - All Models

Theseatdepth,backheight/angle,seatangle,size/positionofthefrontcasters,

size/positionoftherearwheels,antitippermodel,aswellastheuserconditiondirectlyrelatetothestabilityofthewheelchair.Anychangetoone(1)oranycombinationoftheten(10)maycausethewheelchairtodecreaseinstability.TheseadjustmentsMUSTbeperformedbyaqualifiedtechnician.

Thevariousseattofloorheightsrequirespecificsettingsdependingonrearwheelsize,rearwheelposition,frontcastersize/positionanddesiredseattofloorangle.TheseadjustmentsMUSTbeperformedbyaqualifiedtechnician.

NOTE:Whenchangestothelefthandcolumnoccur,followacrossthechartandrefertotheX

proceduretomaintaintheproperstability,

safetyandhandlingofthewheelchair. B

ACKHEIGHT

SEATDEPTH

B

ACKANGLE

SEA

TINGSYSTEM

CASTERSIZE

CASTERPOSITION

WHEELSIZE

WH

EELPOSITION

USE

RCONDITION

W

HEELLOCKS

A

NTI-TIPPERS

BACK HEIGHT X X X X X X X N/A N/A N/A

SEAT DEPTH X X X X X X X N/A N/A N/A

BACK ANGLE X X X X X X X N/A N/A N/A

SEATING SYSTEM X X X X X X X X N/A N/A

CASTER SIZE X N/A X N/A X X X N/A X X

CASTER POSITION X N/A X N/A X X X N/A X X

WHEEL SIZE X N/A X N/A X X X N/A X X

WHEEL POSITION X N/A X N/A X X X N/A X X

USER CONDITION X X X X X X X X N/A N/ASEAT HEIGHT X N/A X X X X X X N/A X X


13/88


Part No. 1076155 13 9000 Series

Stability - Recliner Models Only

ALWAYSmakesurethatthewheelchairisstablebeforeusingthereclineroption.

Ensurethespreaderbarisattachedandsecuredbeforeusingthe9000XTRecliner.

ALWAYSreturnthebacktotheuprightpositionbeforeliftingthewheelchair.

LiftKitModelsonly BothspringliftmechanismsMUSTbeoperationalbeforeusingthe

recliner.DONOToperatethereclineroptionifonlyone(1)ofthespringliftmechanismsisoperational.

Anti-Tippers

Antitippersarespecifictothedifferentseattoflooranglesand/orseattofloorheights.RefertothechartsinInstalling/AdjustingAntitippersonpage 80forcorrectusageandadjustment.Iftheserequirementscannotbeachieved,DONOTusethewheelchair.Contactaqualifiedtechnician.Ifchangingtheseattofloorheightwithorwithoutachangetoseattofloorangle,thecorrectantitippersMUSTbeusedtomaintaina1to

2inchgroundclearance.

Seattofloorangleof0or3:Ifsoequipped,antitippersMUSTbeattachedatalltimes.Inasmuchastheantitippersareanoptionfor0or3onthiswheelchair(youmayorderwithorwithouttheantitippers),Invacarestronglyrecommendsorderingtheantitippersasasafeguardforthewheelchairuser.

Seattofloorangleof6:Ifchangingtheseattofloorangleto6,antitippersMUSTbeinstalled.

Operating Information

InvacareproductsarespecificallydesignedandmanufacturedforuseinconjunctionwithInvacareaccessories.Accessoriesdesignedbyothermanufacturershavenotbeentested

byInvacareandarenotrecommendedforusewithInvacareproducts.

Unlessotherwisenoted,allserviceandadjustmentshouldbeperformedwhilethewheelchairisunoccupied.

Whencleaningrearcaneorhandgripareasuseonlyacleantowellightlydampenedwithcoolwater.Verifythatgripsaredrypriortouse.Useofsoaporammoniabasedcleaningsolutionswillresultinthehandgripsslidingoffthecaneassembly.Failuretoobservethiswarningmayresultininjurytotheuserorbystanders.

Ifthewheelchairisexposedtoextremetemperature(above100Forbelow32F),highhumidityand/orbecomeswet,ensurepriortousethatthehandgripsdonottwistonthehandle.Otherwise,damageorinjurymayoccur.

Avoidstoringorusingthewheelchairnearopenflameorcombustibleproducts.Seriousinjuryordamagetopropertymayresult.


14/88


9000 Series 14 Part No. 1076155

DONOTattempttoliftthewheelchairbyanyremovable(detachable)parts.Liftingbymeansofanyremovable(detachable)partsofthewheelchairmayresultininjurytotheuserordamagetothewheelchair.

9000XTReclineronly DONOTusethespreaderbartoliftthewheelchair.

DONOTstandontheframeofthewheelchair.

DONOT

use

the

footplate

as

aplatform.

When

getting

in

or

out

of

the

wheelchair,

make

surethatthefootplatesareintheupwardposition.

NEVERusequickreleaseaxlesonthe9000XT(modelswithoffsetaxleoptiononly),9000XDTor9000XTReclinerwheelchairs.

Tire Pressure

DONOTusethewheelchairunlessithasthepropertirepressure(p.s.i.).DONOToverinflatethetires.Failuretofollowthesewarningsmaycausethetiretoexplodeandcausebodilyharm.Therecommendedtirepressureislistedonthesidewallofthetire.

Weight Training

Invacaredoesnotrecommendtheuseofitswheelchairsasaweighttrainingapparatus.Invacarewheelchairshavenotbeendesignedortestedasaseatforanykindofweighttraining.Ifoccupantusessaidwheelchairasaweighttrainingapparatus,Invacareshallnotbeliableforbodilyinjuryordamagetothewheelchairandthewarrantyisvoid.

Weight Limitation

The9000SL,9000XT,and9000XTReclinerwheelchairshaveaweightlimitationof250lbs(114kg).The9000XDTwheelchairhasaweightlimitationof350lbs(159kg).


15/88

SECTION 2SAFETY INSPECTION/TROUBLESHOOTING

Part No. 1076155 15 9000 Series

SECTION 2SAFETYINSPECTION/TROUBLESHOOTINGNOTE:Initialadjustmentsshouldbemadetosuittheenduserspersonalbodystructureneedsandpreference.Afterinitialsetup,performtheseprocedureseverytimethewheelchairisserviced.

Checklist

Ensurethatthewheelchairrollsstraight(noexcessivedragorpulltooneside).

Inspectforlooseormissinghardwareonframeandcrossbraces.

Inspectforbentframeorcrossbraces.

Checkthatthewheellocksdonotinterferewithtireswhenrolling.

Checkthatthewheellockpivotpointsarefreeofwearandlooseness.

Checkthatthewheellocksareeasytoengage. Ensurethatthewheellockspreventthewheelchairfrommovingwhenengaged.

Inspecttheseatandbackforripsandsagging.

Inspecttheseatandbackforlooseorbrokenhardware.

Inspectthebackcanehandgripsforwear/looseness/deterioration.

Inspectseatpositioningstrapforanysignsofwear.Ensurebucklelatches.Verifyhardwarethatattachesstraptoframeissecureandundamaged.Replaceifnecessary.

Inspecttiresforflatspotsandwear.

Checkpneumatictiresforproperinflation.

CAUTIONAs with any vehicle, check the wheels and tires periodically for cracks and wear.Replace if damaged.

Ifequipped,checkthatquickreleaseaxleslockproperly.Lubricateifnecessary.

Checkthatthereisnoexcessivesidemovementorbindingintherearwheelswhenliftedandspun.

Inspectrearwheelsforcracked,bentorbrokenspokes.

Ensureallspokesareuniformlytight.

Inspecthandrimsforsignsofroughedgesorpeeling.

Inspectaxleassemblyforpropertensionbyspinningcaster.Castershouldcometoagradualstop.

Adjustfrontcasters/forksbearingsystemifwheelwobblesnoticeablyorbindstoastop.


16/88


9000 Series 16 Part No. 1076155

Ensurewheelbearingsarecleanandfreeofmoisture.

Checkheadtubelocknutsfortightness.

Inspectcastersforcracksandwear.

Inspectfrontcastersforcracked,bentorbrokenspokes.

Cleanupholsteryandarmrests.

Checkthatalllabelsarepresentandlegible.Replaceifnecessary.

Troubleshooting

Maintenance

Maintenance Safety Precautions

WARNING

After any adjustments, repair or service and before use, make sure all attachinghardware is tightened securely. Otherwise injury or damage may occur.

CAUTIONDO NOT overtighten hardware attaching to the frame. This could cause damage tothe frame tubing.

Suggested Maintenance Procedures

1. Makesureallnutsandboltsaretight.Checkallpartsfordamageorwearandreplace.Checkallpartsforproperadjustment.

ChairVeersRight/Left

Chair 3Wheels

Sluggish Turn orPerformance

CastersFlutter

SqueaksandRattles

LoosenessinChair

Solutions

X X X X

Check tires forcorrect and equal

pressure

X X X XCheck for loose nuts

and bolts.

X X XCheck caster headtube

angle.

X X

Check that rearwheels are equally

spaced away from seatframe.


17/88


Part No. 1076155 17 9000 Series

2. 9000SL/9000XTonly Keepquickreleaseaxlesfreeofdirtandlinttoensurepositivelockingandproperoperation.RefertoAdjustingQuickReleaseAxleonpage 57.

3. 9000SL/9000XTonly Oilquickreleaseaxlesatleastonceamonth(3in1oilorequivalent).

WARNINGDO NOT use the wheelchair unless it has the proper tire pressure (p.s.i.). DO NOToverinflate the tires. Failure to follow these suggestions may cause the tire to

explode and cause bodily harm.

4. Iftiresarepneumatic,recommendedtirepressureislistedonthesidewallofthetire.

CAUTIONAs with any vehicle, check the wheels and tires periodically for cracks and wear.Replace if damaged.

5. Therearwheels,castersandtiresshouldbecheckedperiodicallyforcracksandwear,andshouldbereplacedifdamaged.

NOTE:Tirewearisexcessiveif:

PneumaticTires thereismissingtreadorthetiresarebald.

UrethaneTires therearecuts,surfacedefectsorthetiresarelooseontherims.

RubberTires 30%ormoreofthetirehaswornaway.

NOTE:Invacarerecommendsthattiresandcastersbereplacedeveryfive(5)years.

6. Periodicallyadjustwheellocksincorrelationtotirewear.RefertoAdjustingPatientOperatedWheelLocksonpage 83.

7. Periodicallycheckhandrimstoensuretheyaresecuredtotherearwheels.Ifloose,tightenthem.

8. Periodicallycheckcasterwheelbearingstomakesuretheyarecleanandfreefrom

moisture.UseaTeflonlubricantifnecessary.

WARNINGWhen cleaning rear cane or hand grip areas use only a clean towel lightly dampenedwith cool water. Verify that grips are dry prior to use. Use of soap or ammonia

based cleaning solutions will result in the hand grips sliding off the cane assembly.

Failure to observe this warning may result in injury to the user or bystanders.

9. Handgripsshouldbecheckedmonthlyforwear/looseness/deterioration. Cleanifdesired.Replaceifloosenessordeteriorationisfound.

10. Checkupholsteryforsagging,ripsortears.


18/88

SECTION 3SEAT AND BACK

9000 Series 18 Part No. 1076155


WARNING

After any adjustments, repair or service and before use, make sure all attachinghardware is tightened securely. Otherwise, injury or damage may occur.

The seat depth, back height/angle, seat angle, size/position of the front casters,size/position of the rear wheels, anti-tipper model, as well as the user conditiondirectly relate to the stability of the wheelchair. Any change to one (1) or any

combination of the ten (10) may cause the wheelchair to decrease in stability. Useextreme caution when using a new seating position.

Adjusting Back Angle

NOTE:Forthisprocedure,refertoFIGURE

3.1.NOTE:Thisprocedureappliesto9000XTand9000SLadjustablebackmodelwheelchairsonly.

NOTE:SpacesaverarmsDONOTworkwiththeadjustableanglebackoption.

1. Loosen,butDONOTremovethepivotscrewandlocknutthatsecuresthebackanglebrackettothewheelchairframe.

2. Removethe

hex

screw,

washers

and

locknutthatsecurethebackanglebrackettothewheelchairframe.

3. Determinethemountingholeinthebackanglebracketforthenecessarybackanglerelativetotheseatframe.

4. Reinstallthebackanglebrackettothewheelchairframewiththeexistinghexscrew,washersandlocknut.Securelytighten.

5. SecurelytightenthepivotscrewandlocknutloosenedinSTEP1.

6. RepeatSTEPS15fortheoppositesideofthewheelchair.

NOTE:Ensurebothbackanglebracketsareadjustedtothesamemountingposition.

FIGURE 3.1 Adjusting Back Angle

Washer

110

10095

9085

Hex

Screw

Back Angle

Bracket

Wheelchair

Frame

Locknut

WasherLocknutPivot Screw

Back Angle

Bracket

Back Angle

Bracket

Back Angle

BracketBack Angle

Bracket

Back Angle

Bracket

Back Angle

Bracket

105
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


19/88


Part No. 1076155 19 9000 Series

Adjusting Back Height

9000 SL without Adjustable Back Angle Option

NOTE:Forthisprocedure,refertoFIGURE3.2.

NOTE:Therearetwo(2)heightrangesofbackcaneswiththree(3)heightsettingswithineach

range(15to17inchesor17to19inches)andtwo(2)backupholsteryheightsavailable.

1. Ifchangingbackcanes,removetheexistingbackupholstery.RefertoReplacingtheBackUpholsteryintheOwnersManual,partnumber1056953.Otherwise,proceedtoSTEP2.

2. Flipswingbackarmsupandoutoftheway.RefertoSwingBackArmsintheOwnersManual,partnumber1056953.

3. Removethe

mounting

screw

and

locknutthatsecuretheexistingbackcanetothewheelchairframe.

NOTE:Makeanoteofmountingscrewandlocknutorientationforreinstallation.

4. Removeexistingbackcaneifchangingheightrange.

5. RepeatSTEPS23foroppositesideofwheelchair.

6. Slidethe

new/existing

back

canes

into

thewheelchairframe. FIGURE 3.2 Adjusting Back Height- 9000SL without Adjustable Back Angle Option

7. Lineupmountingholesinthewheelchairframeandthenew/existingbackcanes.

NOTE:Thebackcanescontainathreadedinsert.Makesuremountingholesintheinsertlineupwiththemountingholesinthebackcane(DetailA).

8. Installnew/existingbackcanebyperformingthefollowing:

A. Threadexistingmountingscrewthroughthethreadedinsertofthenew/existingbackcanes.

B. Securelytightenmountingscrewandlocknutthatsecurethenew/existingback

canetothewheelchairframe.

9. Ifchangingbackcanes,securelytightenthenewbackupholsterytothebackcanes.RefertoReplacingtheBackUpholsteryintheOwnersManual,partnumber1056953.Otherwise,proceedtoSTEP9.

10. Fliptheswingbackarmsdownforuse.RefertoSwingBackArmsintheOwnersManual,partnumber1056953.

Height

Settings

Locknut Wheelchair

Frame

Mounting

Screw

Back

Cane

DETAIL A

Threaded

Insert

Mounting

Hole

NOTE:Threadedinsertfitsinsidebackcane.
http://-/?-http://-/?-http://-/?-http://-/?-


20/88


9000 Series 20 Part No. 1076155

9000 SL with Adjustable Back Angle Option and 9000 XT/XDT


1. Removethetwo(2)mountingscrews,spacersandlocknutsthatsecurethetwo(2)backcanestothewheelchairframe(DetailA).

2. Repositionthebackcanestoone(1)offive(5)heightadjustmentpositions(Detail

B):

NOTE:Holesarenumberedfrombottomtotopforreferenceonly.Therearenonumbersonthebackcanes.

3. Reinstallthetwo(2)mountingscrews,spacersandlocknutsthatsecurethebackcanestothewheelchairframeandsecurelytighten.

NOTE:Thespacersmustbeontheoutsideofthewheelchairinordertoproperlytightenthemountingscrews.

FIGURE 3.3 Adjusting Back Height- 9000 SL with Adjustable Back Angle Option and 9000XT/XDT

Adjusting Seat Width


NOTE:Whenadjustingtheseatwidthofthewheelchair,thebackandseatupholsteryMUSTbechanged.Ifapplicable,theheadrestpillowandheadrestupholsteryMUSTbechangedaswell.

1. Removetheexistingbackandseatupholsteryfromthewheelchair.RefertoReplacingtheBackUpholsteryandReplacingtheSeatUpholsteryintheownersmanual,partnumber1056953.

HOLE NUMBER 1 & 2 2 & 3 3 & 4 4 & 5 5 & 6

BACK HEIGHT 15 in. 16 in. 17 in. 18 in. 19 in.

Height

Adjustment

Positions

654321

Hole

Back Cane

Wheelchair

Frame

Back Cane

Wheelchair

Frame

Mounting Screws

Spacers Locknuts

DETAIL A DETAIL B


21/88


Part No. 1076155 21 9000 Series

2. Removethefour(4)buttonscrewsandlocknutsthatsecurethetwo(2)pivotlinkstothewheelchairframeandcrossbraces.

3. Removethetwo(2)buttonscrews,locknutsandcrossbracesaddlethatsecuresthebottomofthecrossbracetothewheelchairframe.Repeatforothercrossbrace.

4. Removethehexscrew,covedwashers,washersandlocknutthatsecurethetwo(2)crossbracestogether.SeeDetail B ofFIGURE3.4.

NOTE:Makenoteoftheorientationofthecovedwashers,washersandlocknutforassemblingthenewcrossbraces.RefertoDetail BofFIGURE3.4.

5. Assemblethetwo(2)newcrossbracestogetherwiththeexistinghexscrew,covedwashers,washersandlocknut.Securelytighten.RefertoDetail B ofFIGURE3.4forhardwareorientation.

6. Determinethecorrectpivotlinkandmountingholetousewiththedesiredseatwidth.Refertothefollowingchart.

*NOTE:16,18,and20incharetheonlycrossbracesettingsavailableonthe9000SL.

7. Securethepivotlinktothecrossbracesandwheelchairframewiththefour(4)buttonscrewsandlocknuts.Securelytighten.

NOTE:Positioncrossbracesaddleonwheelchairframeusingthewasherontheundersideofthewheelchairframeasareference.RefertoDetail A ofFIGURE3.4forproperpositioningofthecrossbracesaddle.

8. Reinstallthetwo(2)buttonscrews,locknutsandcrossbracesaddlethatsecurethebottomofthenewcrossbracetothewheelchairframe.RefertoDetail B ofFIGURE3.4forhardwareorientation.Repeatforoppositecrossbrace.Securelytighten.

9. Installthenewbackandseatupholsteryontothewheelchair.RefertoReplacingBackUpholsteryandReplacingSeatUpholsteryintheownersmanual,partnumber1056953.

SEAT WIDTH PIVOT LINK

14-INCH15-INCH

*16-INCH*18-INCH

*20-INCH

22-INCH

14-Inch 15-Inch

16-Inch

x

18-Inch

DO NOT use

20-Inch

22-Inch


22/88


9000 Series 22 Part No. 1076155

FIGURE 3.4 Adjusting Seat Width

Wheelchair

Frame Button Screw

(STEPS 2,7)

Crossbrace

(STEPS 4,5)

Pivot Link

(STEPS 2,7)Locknut

(STEPS 2,7)

Button Screw

(STEPS 2,7)Locknut

(STEPS 2,7)

Crossbrace

Saddle

(STEPS 3,8)

Button Screw

(STEPS 3,8)

Locknut

(STEPS 3,8)Button Screw

(STEPS 2,7)Locknut

(STEPS 2,7)

Crossbrace

Saddle

(STEPS 3,8)

Coved

Washers

Washer

Coved

Washers

Washer

Locknut

Washer

Hex Screw

Coved

Washer

CrossbracesWheelchair

Frame

Washer

Crossbrace

Saddle

DETAIL A

DETAIL B (STEPS 4 AND 5)


23/88


Part No. 1076155 23 9000 Series

Adjusting Seat Depth

WARNINGThe seat depth, back height/angle, seat angle, size/position of the front casters,size/position of the rear wheels, anti-tipper model, as well as the user condition

directly relate to the stability of the wheelchair. Any change to one (1) or any com-

bination of the ten (10) may cause the wheelchair to decrease in stability. Useextreme caution when using a new seating position.

9000XT Model


1. Removetheexistingseatupholsteryfromthecrossbraces.RefertoReplacingSeatUpholsteryinthe

OwnersManual,partnumber1056953.

NOTE:Whenadjustingtheseatdepthofthewheelchair,theseatupholsteryMUSTalsobechanged.

2. Removethetwo(2)plugbuttonsfromtheendsofthecrossbracesthataretowardthefrontofthewheelchair.

NOTE:Theplugbuttonsareusedintheendsoftheseatextensionspacers.

3. Installthetwo(2)seatextensiontubesintotheendsonthecrossbraces.

FIGURE 3.5 Adjusting Seat Depth-

9000XT Model

4. Performone(1)ofthefollowing:

1inchSeatExtension Alignthefrontmostmountingholeoftheseatextensiontubewiththefrontmostmountingholeinthecrossbrace.

2inchSeatExtension Alignthemiddlemountingholeoftheseatextensiontubewiththefrontmostmountingholeinthecrossbrace.

5. RepeatSTEP4fortheoppositeseatextensiontube.

6. Installthe

two

(2)

seat

extension

spacers

onto

the

two

(2)

seat

extension

tubes.

7. Securethenewseatupholsterytothecrossbraces.RefertoReplacingSeatUpholsteryintheOwnersManual,partnumber1056953.

NOTE:Makesuretolineupthemountingholesintheseatextensiontubesandtheseatextensionspacerswiththenewseatupholstery.

8. Installplugbuttonsintotheendsoftheseatextensionspacers.

Mounting

Screws

Seat

ExtensionSpacer

Washer Seat

Upholstery

Crossbrace

Hole for 1-inch

Seat Extension

Seat

Extension

TubePlug Button

Hole for 2-inch

Seat Extension

Front of

Seat

Rear of

Seat


24/88


9000 Series 24 Part No. 1076155

9000 XDT and 9000 SL


NOTE:9000XDTwheelchairshavetwo(2)framedepthranges:16to18inchesand19to20inches.A1618inchframedepth

wheelchaircannotbeadjustedtoa19to20inchrangeandviceversa.

1. Removetheexistingseatupholsteryfromthewheelchair.RefertoReplacingtheSeatUpholsteryintheOwnersManual,partnumber1056953.

NOTE:Whenadjustingtheseatdepthofthewheelchair,theseatupholsteryMUSTalsobechanged.

2. Removethe

two

(2)

plug

buttons

from

theendsofthecrossbracesthataretowardsthefrontofthewheelchair.

NOTE:Thetwo(2)plugbuttonsareusedintheendsoftheseatextensiontubes.

3. Installthetwo(2)seatextensiontubesintotheendsonthecrossbraces.


9000XDT Alignthesecond

mountingholefromtherearoftheseatextensiontubewiththefrontmostmountingholeinthecrossbrace.

NOTE:DONOTusebackmountinghole.Ifbackmountingholeisused,themountingholefortheothermountingscrewwillnotlineupproperly.

FIGURE 3.6 Adjusting Seat Depth- 9000XDT and 9000 SL

9000SL Aligntherearmountingholeoftheseatextensiontubewiththesecondmountingholefromthefrontofthecrossbrace.Slidespacertubeoverseat

extensiontube.

NOTE:Therearmountingholeisfurtherfromitsendoftheseatextensiontubethanthefrontmountingholeisfromitsend.

NOTE:Theendofthespacertubethatisclosertothespacertubemountingholeshouldfacetothefront.

5. RepeatSTEP4fortheoppositeseatextensiontube.

Spacer

Tube

Mounting Screws

9000 XDT

Seat Upholstery

Washer

Seat

Extension

Tube

Plug Button

Second

Mounting

Hole

DO NOT use

this back

mounting hole

Crossbrace

9000 SL

Seat Extension

Tube

Mounting Screws

Seat Upholstery

Second

Mounting

Hole

Crossbrace

Rear

Mounting

Hole

Plug Button

Front ofSeat

Rear of

Seat

Rear of

Seat

Front of

Seat

Spacer Tube

Mounting Hole


25/88


Part No. 1076155 25 9000 Series

6. Installthenewseatupholsteryontothewheelchair.Makesuretolineupthemountingholesintheseatextensiontubeswiththenewseatupholstery.RefertoReplacingSeatUpholsteryintheOwnersManual,partnumber1056953.

7. Installplugbuttonsintotheendsoftheseatextensiontubes.


26/88

SECTION 4FRONT CASTERS

9000 Series 26 Part No. 1076155


WARNINGAfter any adjustments, repair or service and before use, make sure all attaching

hardware is tightened securely. Otherwise, injury or damage may occur.

Front Caster Mounting Adjustments


1. Removethehexscrew,washers(ifsoequipped)andlocknutthatsecurethefrontcastertothefork.

2. Repositionthefrontcasterontheforktothedeterminedmountinghole.RefertoChangingSeattoFloorHeight/SeattoFloorAngleonpage 29todeterminefrontcastermountingholeforfrontcastersizeandseattofloorheight.

3. Securefrontcastertoforkwithexistinghexscrewandlocknut.Securelytighten.

WARNINGMake sure both front casters are positioned in the same mounting hole before usingthe wheelchair. Otherwise, injury may result.

4. RepeatSTEPS13fortheoppositefrontcaster.

FIGURE 4.1 Front Caster Mounting Adjustments

Fork

Front

Caster

Washer

Locknut

Washer

Hex Screw


27/88


Part No. 1076155 27 9000 Series

Converting from Trailing to Leading or Leading to

Trailing Casters


Adjustingthecasterheadtubeposition(leadingortrailing)changesthewheelbase

lengthofthewheelchair.Therearetwo(2)adjustmentswhichallowfora:

Longerwheelbase Thecasterheadtubeisleadingorinfrontofthewheelchairframe.

Shorterwheelbase Thecasterheadtubeistrailingorbehindthewheelchairframe.

NOTE:Ifthecasterheadtubesarepositionedin

theleading

position

when

using

8inch

casters,

a60footrestisrecommendedtoallowadequateroomforfeetandcasterswivel.

NOTE:Makenoteoftheorientationofthecamforproperreinstallation.Ifchangingtheseattofloorheightand/ortheseattofloorangle,refertoChangingSeattoFloorHeight/SeattoFloorAngleonpage 29.

1. Removethetwo(2)mountingscrews,covedspacer,washer,camandtwo(2)

locknutsthatsecuretheinsertandthecasterheadtubetothewheelchairframe.

NOTE:Theinsertwilldropifitisnotcaught.

2. RepeatSTEP1foroppositeside.

3. Positiontheexistingrightcasterheadtubeontotheleftwheelchairframe.

NOTE:Ensuretheinsertispositionedintothe

bottomofthewheelchairframewiththemountingholesalignedwiththeframemountingholes.

4. Ensurecovedspacerisproperlypositionedwiththeroundedendup.Thecutout(DetailA)ontheundersideofthecovedspacershouldcleartheframejoint.

FIGURE 4.2 Converting from Trailing toLeading or Leading to Trailing Casters

Washer

Cam

Locknuts

Coved

Spacer

Caster

Headtube

Insert

MountingScrews

Wheelchair Frame

Leading

Trailing

Wheelchair

Frame

Frame Joint

Coved Spacer

Cam

Locknuts

Washer

Caster Headtube

Insert

Mounting

Screws

DETAIL A - COVED SPACER

Rounded

EndCut-out onUnderside of

Coved Spacer

Frame

Mounting

Holes

Frame

Mounting

Holes


28/88


9000 Series 28 Part No. 1076155

5. Looselytightenthebottomoftheexistingcasterheadtubetothewheelchairframeusingexistinghardware.

6. Adjusttheseattofloorangle.RefertoChangingSeattoFloorHeight/SeattoFloorAngleonpage 29.

7. Securethecamtothetopofthecasterheadtubewiththeexistinghardware.

8. Securelytighten

the

caster

headtube

to

the

wheelchair

frame.

Torque

locknuts

to

120140inchlbs.

9. Adjusttheantitippers.RefertoInstalling/AdjustingAntitippersonpage 80.

Repositioning/Replacing Cam


1. Doone(1)ofthefollowing:

ToReposition RefertoChangingSeattoFloorHeight/SeattoFloorAngleon

page 29. ToReplace Beforeremovingthecam,makenoteofthepositionofthecaminthe

casterheadtubeforproperreinstallation.Thenremove.

2. Loosenthebottommountingscrewandlocknutthatsecuresthecasterheadtubetothewheelchairframe.

NOTE:Looseningthebottommountingscrewallowsthecamtobepositionedeasilyinthecasterheadtube.

3. Removethetoplocknutandcamfromthecasterheadtube.

4. Installthenew/existingcamatthepositionobservedinSTEP1.

5. Tightenbothlocknutstosecurethecasterheadtubetothewheelchairframe.Torqueto120140inchlbs.


29/88

SECTION 5SEAT TO FLOOR

Part No. 1076155 29 9000 Series




Changing Seat-to-Floor Height/Seat-to-Floor Angle

WARNING

Before performing this procedure, refer to Stability - All Models on page 12foradditional requirements.

DO NOT deviate from the charts on the following pages. If the restrictions forseat-to-floor heights and seat-to-floor angles are not followed, the wheelchair will be

in an unsafe position. Before changing these settings, refer to the following chartsfor the allowable positions.

NOTE:Forthisprocedure,refertoFIGURE 5.1.

NOTE:Thissectionisfornonreclinerwheelchairsonly.Forrecliners,refertoChangingSeattoFloorHeightonpage 77.

NOTE:Seattofloorangleadjustmentsareonlyavailableon9000XTwiththeoffsetaxleoptionandadjustablecasterjournal(ADJC).Allothermodels/optionshavea3seattofloorangle.

ThedifferentSeattoFloorheightsandangles(DetailA)arepossiblebyusingdifferentcombinationsofrearwheels,rearwheelpositions,frontcasterpositions,frontcastersizeandcampositions.

1. Determinethemodelandframestyleofyourwheelchair.RefertothefollowingchartandFIGURE 5.1.

MODEL FRAME STYLE

Adult/Hemi Adult/Tall Super Low

9000 SL X N/A N/A

9000 XT X N/A X

9000 XT with Bolt-on-Headtube (ADJC) X N/A N/A

9000 XDT N/A X N/A


30/88


9000 Series 30 Part No. 1076155

FIGURE 5.1 Changing Seat-to-Floor Height/Seat-to-Floor Angle

2. Refertothefollowingchartsofrearwheelsizesandfrontcastersizestodeterminemountingadjustmentsforobtainableseattofloorheights/anglesfortheappropriateframestyle.

SuperLowFrameStyleonpage 31

Adult/TallFrameStyleonpage 31

Adult/HemiFrame

Styles

on

page 32

ChangingSeattoFloorHeightonpage 77forreclinerframestyles

NOTE:Ifusingamputeebrackets,thefollowingrestrictionsapply:

Angle a3seattofloorangleistheonlyavailableangle.

RearWheelMountingPosition RefertothechartsintheOwnersManual,partnumber1056953,fortheproperrearwheelmountingposition.

3. Removetherearwheels.RefertoRemoving/Installing RearWheelsonpage 52.

4. Ifnecessary,adjustthecasterheadtubepositionand/orthecamposition.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27and/or

Repositioning/Replacing Camonpage 28.

5. Ifnecessary,replacetheforks.RefertoInstalling/Replacing SixorEightInchFrontCastersandForksintheOwnersManual,partnumber1056953.

6. Ifnecessary,adjustthefrontcasterpositioninthefork.RefertoFrontCasterMountingAdjustmentsonpage 26.

7. Reinstalltherearwheelsontothewheelchair.RefertoRemoving/InstallingRearWheelsonpage 52.

Seat-to-Floor

Height

Seat-to-Floor

Angle

Adult/Hemi Adult/Tall Super Low Recliner

DETAIL A


31/88


Part No. 1076155 31 9000 Series

8. Adjustthewheellocks.RefertoUsing/AdjustingthePatientOperatedWheelLocksintheOwnersManual,partnumber1056953.

WARNINGAfter changing seat-to-floor height and/or seat-to-floor angle, the anti-tippersMUST be replaced or adjusted before using the wheelchair. Refer to

Installing/Adjusting Anti-tippers on page 80.

Super Low Frame Style

NOTE:Forthisinformation,refertothefollowingtableandtoFIGURE 5.2.

FIGURE 5.2 Super Low Frame Style

Adult/Tall Frame Style

NOTE:Forthisinformation,refertothefollowingtableandtoFIGURE 5.3.

6-inch Front Casters, 3 Seat Angle

SEAT-TO-FLOORHEIGHT(INCHES)

FRONTCASTER

MOUNTINGPOSITION

REAR WHEEL SIZE ANTI-TIPPER PARTNUMBER

1314

TopMiddle

20-inch22-inch

10645201064520

8-inch Front Casters, 3 Seat Angle

SEAT-TO-FLOORHEIGHT

(INCHES)

FRONT CASTERMOUNTING

POSITION

REARWHEEL

SIZE

REAR WHEELMOUNTING

POSITION

ANTI-TIPPERPART

NUMBER17191921

TopTop w/ 2-inch extension

BottomBottom w/ 2-inch extension

24-inch24-inch24-inch24-inch

TopMiddleMiddleBottom

1058752105875210587521058836

Bottom (Not used with

Super Low frame style)

Rear Wheel

Mounting Positions

6-Inch Fork

Mounting Positions

Top

Middle


32/88


9000 Series 32 Part No. 1076155

FIGURE 5.3 Adult/Tall Frame Style

Adult/Hemi Frame Styles

Refertothechartsonthefollowingpagesforobtainableseattofloorheightsandseattoflooranglesforwheelchairswiththeadult/hemiframestyle.

24-Inch Rear Wheels and 8-Inch Front Casters

WARNING

If changing the seat-to-floor angle to 6, anti-tippers MUST be installed.

Refertothefollowingtabletodeterminetheobtainableseattofloorheightsandseattoflooranglesfor24inchrearwheelsand8inchfrontcasters:

*NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.Theseheightscanvary+/ inchduetotirewearandmanufacturingtolerances.

SEAT-TO-FLOORHEIGHT*

SEAT-TO-FLOORANGLE

REFER TO

19 inches 3 Chart 1

19 inches 6 Chart 2

18 inches 0 Chart 3

18 inches 3 Chart 4

18 inches 6 Chart 5

17 inches 0 Chart 6

17 inches 3 Chart 7

17 inches 6 Chart 8

Rear Wheel

Mounting Positions

8-Inch Fork

Mounting Positions

Without 2-Inch

Extension

With 2-Inch

ExtensionTop

TopTop

Middle

Bottom

Middle (Not used

with Adult/Tall

frame style)

Bottom Bottom

Middle (Not used

with Adult/Tall

frame style)


33/88


Part No. 1076155 33 9000 Series

NOTE:Charts1to8applytoadult/hemiframestylesonly.Refertothechartsforseattofloorheightsettingsforadult/tall(Adult/TallFrameStyleonpage 31)andsuperlowframestyles(SuperLowFrameStyleonpage 31)andChangingSeattoFloorHeightonpage 77forrecliner

framestyles.

*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.

*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovide

adequatetire

clearance

between

the

rear

tire

and

the

front

caster.

Refer

to

Converting

from

Trailing

toLeadingorLeadingtoTrailingCastersonpage 27.

Chart 1 - Seat-to-Floor Height of 19 inches and 3 Angle

REAR WHEEL POSITION ANTI-TIP

PART/MODELNUMBERS

FRONT CASTER

OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION

ADJC CAMPOSITIONFORWARD* REARWARD

1360 On-Chair

1058836Off-Chair


REAR WHEEL POSITION ANTI-TIPPART/MODEL

NUMBERS

FRONT CASTER



N/A for thisframe style

N/A On-Chair

1113766Off-Chair

Hole 1

Hole 3

Hole 1

Hole 3

Front

Notch

Hole 4

Hole 2

Hole 4

Hole 2

Notch

Front


34/88


9000 Series 34 Part No. 1076155

*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailing





NUMBERS

FRONT CASTER



N/A On-Chair

1058836 Off-Chair



NUMBERS

FRONT CASTER




1360 On-Chair

1058836 Off-Chair

Hole 1

Hole 3

Hole 1

Hole 3

Front

Notch

Hole 4

Hole 2

Hole 4

Hole 2

Front

Notch


35/88


Part No. 1076155 35 9000 Series





NUMBERS

FRONT CASTER



N/A On-Chair

1113766Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1058836 Off-Chair

Hole 4

Hole 3

Hole 4

Hole 3Notch

Front

Hole 4

Hole 2

Hole 4

Hole 2

Front

Notch


36/88


9000 Series 36 Part No. 1076155





NUMBERS

FRONT CASTER



1360 On-Chair

1058836Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1113766Off-Chair

Hole 4

Hole 3

Hole 4

Hole 3

Front

Notch

Hole 4

Hole 5

Hole 4

Hole 5

Notch

Front


37/88


Part No. 1076155 37 9000 Series


WARNINGIf changing the seat-to-floor angle to 6, anti-tippers MUST be installed.

Refertothefollowingtabletodeterminetheobtainableseattofloorheightsand

seatto

floor

angles

for

24

inch

rear

wheels

and

6inch

front

casters:



framestyles.


SEAT-TO-FLOORANGLE

REFER TO

17 inches 0 Chart 9

17 inches 3 Chart 10






REAR WHEEL POSITION ANTI-TIP

PART/MODELNUMBERS

FRONT CASTER


ADJC CAMPOSITIONFORWARD REARWARD


N/A On-Chair

1058836Off-Chair

Hole 4

Hole 2

Hole 4

Hole 2

Front

Notch


38/88


9000 Series 38 Part No. 1076155



NUMBERS

FRONT CASTER



N/A On-Chair

1058752Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1113765Off-Chair



NUMBERS

FRONT CASTER



N/A On-Chair

1058836Off-Chair

Hole 4

Hole 3

Hole 4

Hole 3

Front

Notch

Hole 4

Hole 5

Hole 4

Hole 5

Notch

Front

Hole 4

Hole 3

Hole 4

Hole 3

Front

Notch


39/88


Part No. 1076155 39 9000 Series





NUMBERS

FRONT CASTER




N/A On-Chair

1058752Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1058752 Off-Chair

Hole 4

Hole 5

Hole 4

Hole 5

Front

Notch

Hole 4

Hole 5

Hole 4

Hole 5

Front

Notch


40/88


9000 Series 40 Part No. 1076155




framestyles.



SEAT-TO-FLOORANGLE

REFER TO









NUMBERS

FRONT CASTER



N/A On-Chair

1113766 Off-Chair

Hole 1

Hole 3

Hole 1

Hole 3

Notch

Front


41/88


Part No. 1076155 41 9000 Series






NUMBERS

FRONT CASTER



1360 On-Chair

1058836 Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1113766

Off-Chair

Hole 1

Hole 3

Hole 1

Hole 3

Front

Notch

Hole 4

Hole 2

Hole 4

Hole 2

Notch

Front


42/88


9000 Series 42 Part No. 1076155






NUMBERS

FRONT CASTER




N/A On-Chair

1058836 Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1058836

Off-Chair

Hole 1

Hole 3

Hole 1

Hole 3

Front

Notch

Hole 4

Hole 2

Hole 4

Hole 2

Front

Notch


43/88


Part No. 1076155 43 9000 Series

*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovide

adequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.






framestyles.



NUMBERS

FRONT CASTER



N/A On-Chair

1113766Off-Chair


SEAT-TO-FLOORANGLE

REFER TO









Hole 4

Hole 3

Hole 4

Hole 3Notch

Front


44/88


9000 Series 44 Part No. 1076155



NUMBERS

FRONT CASTER



N/A On-Chair

1058836 Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1058752Off-Chair



NUMBERS

FRONT CASTER



N/A On-Chair

1113765Off-Chair

Hole 1

Hole 3

Hole 1

Hole 3

Front

Notch

Hole 4

Hole 2

Hole 4

Hole 2

Front

Notch

Hole 4

Hole 3

Hole 4

Hole 3Notch

Front


45/88


Part No. 1076155 45 9000 Series



NUMBERS

FRONT CASTER




N/A On-Chair

1058836Off-Chair



NUMBERS

FRONT CASTER



1360A On-Chair

1058752Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1113765Off-Chair

Hole 4

Hole 2

Hole 4

Hole 2

Front

Notch

Hole 4

Hole 3

Hole 4

Hole 3

Front

Notch

Hole 4

Hole 5

Hole 4

Hole 5

Notch

Front


46/88


9000 Series 46 Part No. 1076155



Refertothefollowingtabletodeterminetheobtainableseattofloorheightsand

seattoflooranglesfor20inchrearwheelsand8inchfrontcasters:



NUMBERS

FRONT CASTER



N/A On-Chair

1058752Off-Chair



NUMBERS

FRONT CASTER



N/A On-Chair

1058752Off-Chair


SEAT-TO-FLOORANGLE

REFER TO




Hole 4

Hole 3

Hole 4

Hole 3

Front

Notch

Hole 4

Hole 5

Hole 4

Hole 5

Front

Notch


47/88


Part No. 1076155 47 9000 Series



framestyles.



NUMBERS

FRONT CASTER



N/A On-Chair

1113766 Off-Chair



NUMBERS

FRONT CASTER



1360 On-Chair

1058836 Off-Chair

Hole 1

Hole 3

Hole 1

Hole 3

Notch

Front

Hole 1

Hole 3

Hole 1

Hole 3

Front

Notch


48/88


9000 Series 48 Part No. 1076155




*NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.

Theseheights

can

vary

+/

inch

due

to

tire

wear

and

manufacturing

tolerances.


framestyles.



NUMBERS

FRONT CASTER




N/A On-Chair

1113766Off-Chair


SEAT-TO-FLOORANGLE

REFER TO


17 inches 6 Chart 3316 inches 0 Chart 34






Hole 4

Hole 2

Hole 4

Hole 2

Notch

Front


49/88


Part No. 1076155 49 9000 Series



NUMBERS

FRONT CASTER



1360A On-Chair

1058752 Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1113765Off-Chair



NUMBERS

FRONT CASTER



N/A On-Chair

1058836 Off-Chair

Hole 1

Hole 3

Hole 1

Hole 3

Front

Notch

Hole 4

Hole 2

Hole 4

Hole 2

Notch

Front

Hole 1

Hole 3

Hole 1

Hole 3

Front

Notch


50/88


9000 Series 50 Part No. 1076155



NUMBERS

FRONT CASTER




N/A On-Chair

1058752Off-Chair



NUMBERS

FRONT CASTER



N/A On-Chair

1113765Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1058752Off-Chair

Hole 4

Hole 2

Hole 4

Hole 2

Front

Notch

Hole 4

Hole 3

Hole 4

Hole 3Notch

Front

Hole 4

Hole 2

Hole 4

Hole 2

Front

Notch


51/88


Part No. 1076155 51 9000 Series



NUMBERS

FRONT CASTER



1360A On-Chair

1058752Off-Chair



NUMBERS

FRONT CASTER




N/A On-Chair

1113764Off-Chair

Hole 4

Hole 3

Hole 4

Hole 3

Front

Notch

Hole 4

Hole 5

Hole 4

Hole 5

Notch

Front


52/88

SECTION 6REAR WHEELS

9000 Series 52 Part No. 1076155




NOTE:Exceptwherenoted,theproceduresinthissectionapplytononreclinermodelsonly.Forreclinermodels,refertoReclineronpage 58.

Removing/Installing Rear Wheels

Quick-Release Axles

WARNING

NEVER use quick-release axles on the 9000 XT (models with offset axle optiononly), 9000XDT or 9000XT recliner wheelchairs.


NOTE:Ifreplacingthesamesizerearwheel,notethemountingpositiononthewheelchairframeforproperreinstallationofthenewrearwheel.

1. Pushinthedetentpinofthequickreleaseaxle(withwheel)andpulltheaxleoutthroughtheopeninginthecenteroftherearwheelandaxlespacer.

NOTE:Axlespacerisusedonlyifwheelchairisequippedwithconventionalarms.

2. Pushinthedetentpinofthequickreleaseaxleagainandpulltheaxleoutoftherearwheel.

3. RepeatSTEPS12fortheoppositerearwheel.

4. Toreinstalltherearwheelontothewheelchair,reverseSTEPS13.

NOTE:Makesureaxlespacerisbetweenrearwheelandwheelchairframeifwheelchairisequippedwithconventionalarms.

WARNING

Make sure the detent pin and detent balls of the quick-release axle are fully released

before operating the wheelchair.

The detent balls MUST be protruding past the inside of the rear wheel axle bushingfor a positive lock (Detail "A").

Keep detent balls clean.

Invacare recommends inserting quick-release axles with the detent pin to the insideof the wheelchair to prevent accidental release during contact activities.
http://-/?-http://-/?-


53/88


Part No. 1076155 53 9000 Series

5. Ifthedetentballsarenotprotrudingpasttheinsideoftheaxlebushingorthereistoomuchsidetosidemovementoftherearwheelassembly,refertotheOwnersManual(partnumber1056953)forinstructionsonadjustingthequickreleaseaxle.

FIGURE 6.1 Removing/Installing Rear Wheels- Quick-Release Axles

Permanent Axles

Models without Offset Axle Option


NOTE:Ifreplacingthesamesizerearwheel,notethemountingpositiononthewheelchairframeforproperreinstallationofthenewrearwheel.

1. Removethehubcap(ifapplicable),mountingscrewandlocknutthatsecuretherear

wheeland

axle

spacer

(if

applicable)

to

the

wheelchair.

NOTE:Axlespacerisusedonlyifwheelchairisequippedwithconventionalarms.

2. Toreinstalltherearwheelontothewheelchair,reverseSTEP1.

3. Torquelocknutto4045ftlbs.

4. RepeatSTEPS13fortheoppositewheel.

Quick-Release Axle

Detent Pin

Detent Balls

Axle Bushing

DETAIL A - DETENT BALLS AND DETENT PIN

Inside of

Wheelchair

Outside of

Wheelchair

Quick-Release Axle

Rear Wheel

Axle Spacer (Conventional Arms Only)

Axle Mounting PositionsWheelchair Frame


54/88


9000 Series 54 Part No. 1076155

FIGURE 6.2 Removing/Installing Rear Wheels- Permanent Axles- Models without OffsetAxle Option

NOTE:Makesureaxlespacerisbetweenrearwheelandwheelchairframeifwheelchairisequippedwithconventionalarms.

Models with Offset Axle Option


NOTE:Ifreplacingthesamesizerearwheel,notethemountingpositiononthewheelchairframeandintheoffsetaxleplatesforproperreinstallationofthenewrearwheel.

1. Removehubcap.

2. Removethelocknutsecuringthepermanentaxletotheoffsetaxleplates.

3. Removethepermanentaxle,hubcapwasher,two(2)spacersandrearwheelfromthewheelchair.


InstallationInSamePosition ProceedtoSTEP5.

InstallationInDifferentPosition Performthefollowingsteps:

i. RefertothechartsinSeattoFlooronpage 29todeterminethepropermountingpositionforthedesiredseattofloorheightoranglechange.

NOTE:Theoffsetaxleplatesarenumbered(DetailA)onone(1)sideonly.Axleplatesmayneedpositioningwiththenumberedsidetotheinsideofthewheelchair.

NOTE:Theoffsetaxleplatesmaybemountedin

Invacare 9000 Series user Manual

Documents

Transcript of Invacare 9000 Series user Manual