Interior Equipment
Transcript of Interior Equipment
-
7/29/2019 Interior Equipment
1/20
SECTION
14
512001 MY RX300_U (OM48431U)
INSTRUMENTS AND CONTROLS
Interior equipment
Vanity mirrors 52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior lights 53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Personal light 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition switch light 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outside temperature display 56. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cigarette lighter and ashtray 57. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power outlets 58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear console box 59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glove box 59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Garage door opener 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cup holders 63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overhead console box 65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auxiliary boxes 66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage cover 67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Floor mat 68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tiedown hookss 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage stowage precautions 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-
7/29/2019 Interior Equipment
2/20
INTERIOR EQUIPMENT
52 2001 MY RX300_U (OM48431U)
VANITY MIRRORS
14R001a
To use the vanity mirrors, swing the sun visor down and
open the cover.The vanity light comes on when you open the cover.
Sun visors
14R097
1 To block out glare from the front , swing the sun visordown.
2 To block out glare from the side, remove the sun visorfrom the hook and swing it to the side.
3 To block out glare coming obliquely from behind you,slide the visor backwards.
At this position, the vanity light does not come on.
-
7/29/2019 Interior Equipment
3/20
INTERIOR EQUIPMENT
532001 MY RX300_U (OM48431U)
INTERIOR LIGHTS
14R003a
To turn on the interior light, slide the switch.
Center light:
With the switch in the DOOR position, the light comes onwhen any of the side doors or back door are opened. After allthe doors are closed, the light remains on for about 15 secondsand then goes out.
However, in the following cases, the light goes outimmediately:
1. All the doors are closed when the ignition key is in ACC orON position.
2. The ignition key is turned to ACC or ON when the lightis still on.
3. All the doors are locked when the light is still on.
4. One door is closed with the lock button pushed in while theother doors are locked.
Rear light:
With the switch in the DOOR position, the light comes onwhen the back door is opened. The light goes out immediatelywhen the back door is closed.
-
7/29/2019 Interior Equipment
4/20
INTERIOR EQUIPMENT
54 2001 MY RX300_U (OM48431U)
PERSONAL LIGHTVehicles without moon roof
14R004c
To turn on the personal light, push the switch. To turn itoff, push the switch again.
Vehicles with moon roof
14R005b
To turn on the personal light, push the switch. To turn itoff, push the switch again.
-
7/29/2019 Interior Equipment
5/20
INTERIOR EQUIPMENT
552001 MY RX300_U (OM48431U)
IGNITION SWITCH LIGHT
14R102
For easy access to the ignition switch, the ignition switch
light comes on when the drivers door is unlocked.The light remains on for about 15 seconds and goes out afterall the doors are closed. However, the light goes outimmediately when all the doors are locked or the ignition keyis in the ACC or ON position.
CLOCK
14R007c
" 1 12hour display mode 2 24hour display mode
3 Time setting mode (indication blinking)4 Alarm setting mode (indication blinking)
The digital clock indicates the time with the ignition key atthe ACC or ON position. The mode can be changedby pushing the CLOCK button on the audio controlpanel.
With the tail lights on, the brightness of the time indication willbe reduced.
If the electrical power source has been disconnected from theclock, the time display will automatically be set to 1:00 (oneoclock).
-
7/29/2019 Interior Equipment
6/20
INTERIOR EQUIPMENT
56 2001 MY RX300_U (OM48431U)
14R043
Adjusting the time:
1. Push the CLOCK button to enter the time setting mode.
2. Push the H or M button to adjust the time.
3. Push the CLOCK button again.
To set the clock by the radio, adjust the minute to 00 at step2. and push the CLOCK button by the time signal from theradio.
Setting the alarm:
1. Push the CLOCK button to display the alarm setting mode.
2. Input the time you want to sound an alarm by pushing Hor M button.
3. Push the button indicated by the bell mark. The bellindicator appears.
An alarm sounds for about 20 seconds at the set time every
day. To stop the alarm, push the CLOCK button.
To disable the alarm activation, push the button indicated by
the bell mark at step 3. and turns off the bell indicator on thedisplay.
OUTSIDE TEMPERATURE DISPLAY
14R050b
This display shows the outside temperature when theignition switch is on.
The displayed temperature ranges from 22_F (30_C) up to122_F (50_C). If the temperature does not appear on thedisplay or it shows , take your vehicle to your Lexus dealer.
-
7/29/2019 Interior Equipment
7/20
INTERIOR EQUIPMENT
572001 MY RX300_U (OM48431U)
CIGARETTE LIGHTER ANDASHTRAY
14R110
"Cigarette lighter
14R112
"Ashtray
To use the cigarette lighter, press it in. When it becomes
heated, it automatically pops out ready for use. To use theashtray, push the ashtray cover.
Do not hold the cigarette lighter pressed in.
If the engine is not running, the ignition key must be in theACC position.
When finished with your cigarette, thoroughly extinguish it inthe ashtray to prevent other cigarette butts from catching fire.After using the ashtray, push it back in completely.
To remove the ashtray, just pull it up.
Use a Lexus genuine cigarette lighter or equivalent forreplacement.
CAUTION
To reduce the chance of injury in case of an accident orsudden stop while driving, always completely close theashtray after using it.
-
7/29/2019 Interior Equipment
8/20
INTERIOR EQUIPMENT
58 2001 MY RX300_U (OM48431U)
POWER OUTLETS
14R010b
"Rear end of the console box
14R051
"In the luggage compartment
The power outlets are designed for power supply for car
accessories.
The ignition key must be in the ACC or ON position for the
power outlets to be used.
NOTICE
D To prevent the fuse from being blown, do not use theelectricity over the total vehicle capacity of 12V/120W(front and rear outlets together).
D To prevent the battery from being discharged, do notuse the power outlet longer than necessary when theengine is not running.
D Close the power outlet lid when the power outlet isnot in use. Inserting a foreign object other than theappropriate plug that fits the outlet, or allowing any
liquid into the outlet may cause electrical failure orshort circuits.
-
7/29/2019 Interior Equipment
9/20
INTERIOR EQUIPMENT
592001 MY RX300_U (OM48431U)
REAR CONSOLE BOX
14R118
" 1 For upper box 2 For lower box
To use the rear console box, open as shown in theillustration.
GLOVE BOX
14R044
" 1 Unlock 2 Open 3 Lock
To open the glove box door, pull the lever. To lock theglove box door, insert the master key and turn itclockwise.
With the tail lights on, the glove box light will come on when theglove box door is open.
For the CD automatic changer, see page 164.
CAUTION
To reduce the chance of injury in case of an accident ora sudden stop, always keep the glove box door closedwhile driving.
http://../om1sourc/2001om/01rx300o/22.pdfhttp://../om1sourc/2001om/01rx300o/22.pdf -
7/29/2019 Interior Equipment
10/20
INTERIOR EQUIPMENT
60 2001 MY RX300_U (OM48431U)
GARAGE DOOR OPENERThe garage door opener (HomeLinkR UniversalTransceiver) is manufactured under license fromHomeLinkR and can be programmed to operate garagedoors, gates, entry doors, door locks, home lightingsystems, and security systems, etc.
(a) Programming theHomeLinkR
14R098
The HomeLinkR in your vehicle has 3 buttons and youcan store one program for each button.
To ensure correct programming into the HomeLinkR, installa new battery in the handheld transmitter prior toprogramming.
The battery side of the handheld transmitter must be pointedaway from the HomeLink R during the programmingprocess.
For Canadian users, follow the procedure in Programming an
entrance gate/Programming all devices in the Canadianmarket.
1. Decide which of 3 HomeLinkR buttons you want toprogram.
2. Place your handheld garage transmitter 25 to 75 mm (1 to3 in.) away from the surface of the HomeLinkR.
Keep the indicator light on the HomeLinkR in view whileprogramming.
3. Simultaneously press and hold the handheld garagetransmitter button along with the selected HomeLinkR
button.
4. When the indicator light on theHomeLinkR changes from
a slow to a rapid flash after 20 seconds, you can release bothbuttons.
5. Test the operation of the HomeLinkR by pressing thenewly programmed button. If programming a garage dooropener, check to see if the garage door opens and closes.
If the garage door does not operate, identify if your garagetransmitter is of the Rolling Code type. Press and hold theprogrammedHomeLinkR button. The garage door has therolling code feature if the indicator light (on the HomeLinkR)flashes rapidly and then remains lit after 2 seconds. If yourgarage transmitter is the Rolling Code type, proceed to theheading Programming a rolling code system.
6. Repeat steps 2 through 5 for each remainingHomeLinkR
button to program another device.
-
7/29/2019 Interior Equipment
11/20
INTERIOR EQUIPMENT
612001 MY RX300_U (OM48431U)
Programming a rolling code system
If your device is Rolling Code equipped, it is necessaryto follow steps 1 through 4 under the headingProgramming the HomeLinkR before proceeding withthe steps listed below.
1. Locate the training button on the ceiling mounted garagedoor opener motor. The exact location and color of the buttonmay vary by brand of garage door opener. Refer to the ownersguide supplied by the garage door opener manufacturer for thelocation of this training button.
2. Press the training button on the ceiling mounted garagedoor opener motor.
Following this step, you have 30 seconds in which to initiatestep 3 below.
3. Press and release the vehicles programmedHomeLinkR
button twice. The garage door may open. If the door doesopen, the programming process is complete. If the door doesnot open, press and release the button a third time. This thirdpress and release will complete the programming process byopening the garage door.
The ceiling mounted garage door opener motor should nowrecognize the HomeLinkR unit and be able activate thegarage door up/down.
4. Repeat steps 1 through 3 for each remainingHomeLinkR
button to program another rolling code system.
Programming an entrance gate/Programming all devices
in the Canadian market
1. Decide which of the 3 HomeLinkR buttons you want toprogram.
2. Place your handheld gate/device transmitter 25 to 75 mm(1 to 3 in.) away from the surface of the HomeLinkR.
Keep the indicator light on the HomeLinkR in view whileprogramming.
3. Press and hold the selected HomeLinkR button.
4. Continuously press and release (cycle) the handheldgate/device transmitter button every two seconds until s tep 5is complete.
5. When the indicator light on theHomeLinkR changes from
a slow to a rapid flash after 20 seconds, you can release bothbuttons.
6. Test the operation of the HomeLinkR by pressing thenewly programmed button. Check to see if the gate/deviceoperates correctly.
7. Repeat steps 1 through 6 for each remainingHomeLinkR
button to program another device.
Programming other devices
To program other devices such as home security systems,home door locks or lighting, contact your authorized Toyotadealer for assistance.
-
7/29/2019 Interior Equipment
12/20
INTERIOR EQUIPMENT
62 2001 MY RX300_U (OM48431U)
Reprogramming a button
IndividualHomeLinkR buttons cannot be erased, however,to reprogram a single button, follow the procedureProgramming the HomeLinkR.
(b) Operating theHomeLinkR
To operate the HomeLinkR, press the appropriateHomeLinkR button to activate the programmed device. TheHomeLinkR indic ator light should come on. TheHomeLinkR continues to send the signal for up to 20seconds as long as the button is pressed.
(c) Erasing the entireHomeLinkR memory(all three programs)
To erase all previously programmed codes at one time, pressand hold down the 2 outside buttons for 20 seconds until theindicator light flashes.
If you sell your vehicle, be sure to erase the programs storedin the HomeLinkR memory.
CAUTION
D When programming the HomeLinkR UniversalTransceiver, you may be operating a garage door orother device. Make sure people and objects are outof the way of the garage door or other device toprevent potential harm or damage.
D Do not use this HomeLinkR Universal Transceiverwith any garage door opener that lacks the safetystop and reverse feature as required by federal safetystandards. (This includes any garage door openermodel manufactured before April 1, 1982.) A garagedoor opener, which cannot detect an object,signaling the door to stop and reverse, does not meetcurrent federal safety standards. Using a garagedoor opener without these features increases risk ofserious injury or death.
FCC ID: CB2SAHL3CANADA: 279 102 1849A
This device complies with FCC Rules Part 15.Operation is subject to the following two conditions:(1) This device may not cause harmful interference,and (2) this device must accept any interference thatmay be received, including interference that maycause undesired operation. WARNING: Thistransmitter has been tested and complies withFCC and DOC/MD C rules. Change s ormodifications not expressly approved by the partyresponsible for compliance could void the usersauthority to operate the device.
-
7/29/2019 Interior Equipment
13/20
INTERIOR EQUIPMENT
632001 MY RX300_U (OM48431U)
CUP HOLDERS
14R012b
"Front cup holder
To use the cup holder, slide the rear console box.The cup holder is designed for holding cups or drinkcanssecurely. You can adjust the arms to 3 stages.
14R042b
" 1 Upper console position 2 Lower console position
The cup holder can be installed as you desired using theupper and lower rear console boxes.
When the upper console is used as a cup holder, the lowerconsole may not be used. This applies to the opposite casewhen the lower console is used.
-
7/29/2019 Interior Equipment
14/20
INTERIOR EQUIPMENT
64 2001 MY RX300_U (OM48431U)
14R123
" 1 Removal 2 Installation
To remove: Pull out the cup holder from the rear console box.
To install: Insert the rear tabs into the cutouts of the rear
console box.
CAUTION
D Do not place anything else other than cups ordrinkcans in the cup holder, as such items may bethrown about in the compartment and possibly injurepeople in the vehicle during sudden braking or in anaccident.
D To reduce the chance of injury in case of an accidentor sudden stop while driving, keep the cup holderclosed when not in use.
14R058b
"Rear cup holder (rear console box)
To use the cup holder, push the button of the rear consolebox.
The cup holder is designed for holding cups or drinkcanssecurely. You can adjust the arms to 3 stages.
CAUTION
D Do not place anything else other than cups ordrinkcans on the cup holder, as such items may bethrown about in the compartment and possibly injurepeople in the vehicle during sudden braking or in anaccident.
D To reduce the chance of injury in case of an accidentor sudden stop while driving, keep the cup holderclosed when not in use.
-
7/29/2019 Interior Equipment
15/20
INTERIOR EQUIPMENT
652001 MY RX300_U (OM48431U)
14R113
"Rear cup holder (rear seat cushion)
To use the rear cup holder, pull the cup holder portion ofthe rear seat cushion.
The cup holder is designed for holding cups or drinkcanssecurely.
CAUTION
D Do not place anything else other than cups ordrinkcans on the cup holder, as such items may bethrown about in the compartment and possibly injurepeople in the vehicle during sudden braking or in anaccident.
D To reduce the chance of injury in case of an accidentor sudden stop while driving, keep the cup holderclosed when not in use.
OVERHEAD CONSOLE BOX
14R114
To use the overhead console box, open it as shown above.
CAUTION
D To reduce the chance of injury in case of an accidentor a sudden stop, always keep the overhead consolebox closed while driving.
D As this box is designed for holding eyeglasses, donot place any object heavier than approximately 60 g(0.13 lb.) in it. Heavier objects may cause the box toopen and contents to fly out resulting in injuries.
-
7/29/2019 Interior Equipment
16/20
INTERIOR EQUIPMENT
66 2001 MY RX300_U (OM48431U)
NOTICEDuring hot weather, the interior of the vehicle becomesvery hot. Do not leave anything flammable ordeformable such as a lighter, glasses, etc. inside.
AUXILIARY BOXESYour vehicle has several types of auxiliary box. To usethem, open as shown in the following illustrations.
14R023c
"On the instrument panel
14R127
"In the right side of luggage compartment
CAUTION
To reduce the chance of injury in case of an accident ora sudden stop, always keep the auxiliary box closedwhile driving.
-
7/29/2019 Interior Equipment
17/20
INTERIOR EQUIPMENT
672001 MY RX300_U (OM48431U)
LUGGAGE COVER
Using luggage cover
14R124
To use the luggage cover:
1 Attach the front hooks of the luggage cover to the headrestraint.
2 Pull out the rear luggage cover and hook it on theanchors.
CAUTION
Do not place anything on the luggage cover. Such itemsmay be thrown about and possibly injure people in thevehicle during sudden braking or an accident.
Removing luggage cover
14R122
To remove the luggage cover, lift it up.
After you remove the luggage cover, place it somewhere otherthan the passenger compartment. This will preventpassengers from injury in the event of a sudden stop oraccident.
-
7/29/2019 Interior Equipment
18/20
INTERIOR EQUIPMENT
68 2001 MY RX300_U (OM48431U)
FLOOR MAT
14R024
Use a floor mat of the correct size.
If the floor carpet and floor mat have a hole, then it is designedfor use with a locking clip. Fix the floor mat with locking clip intothe hole in the floor carpet.
14R025
CAUTION
Make sure the floor mat is properly placed on the floor
carpet. If the floor mat slips and interferes with themovement of the pedals during driving, it may cause anaccident.
-
7/29/2019 Interior Equipment
19/20
INTERIOR EQUIPMENT
692001 MY RX300_U (OM48431U)
TIEDOWN HOOKS
14R083
To secure your luggage, use the tiedown hooks asshown above.
See Luggage stowage precautions for precautions toobserve in loading luggage.
LUGGAGE STOWAGEPRECAUTIONS
When stowing luggage or cargo in the vehicle, observethe following:
D Put luggage or cargo in the luggage compartment when atall possible. Be sure all items are secured in place.
D Be careful to keep the vehicle level. Placing the weight asfar forward as possible helps maintain vehicle balance.
D For better fuel economy, do not carry unnecessary weight.
CAUTION
D To prevent luggage or packages from sliding forwardduring braking, do not stack anything in the luggagecompartment higher than the seatbacks. Keepluggage or packages low, as close to the floor aspossible.
D Never allow anyone to ride in the luggagecompartment. It is not designed for passengers.They should ride in their seats with their seat beltsproperly fastened. Otherwise, they are much morelikely to suffer serious bodily injury, in the event ofsudden braking or a collision.
-
7/29/2019 Interior Equipment
20/20
INTERIOR EQUIPMENT
70 2001 MY RX300_U (OM48431U)
D Do not drive with objects left on top of the instrument
panel. They may interfere with the drivers field ofview. Or they may move during sharp vehicleacceleration or turning, and impair the driverscontrol of the vehicle. In an accident they may injurethe vehicle occupants.
NOTICE
Do not load the vehicle beyond the vehicle capacityweight specified on the tire pressure label.