Intelligent control terminal-DLP panel Programming

DLP LCD PANEL Programming

Front

Device subnet ID and device ID

Can make remark according to actual location, convenience for maintenance and management

Set the backlight, Higher value make the Great Lightness, And vice versa

DLPINTERFACE FUNCTION

DLP Key number

Remark of each keys

Mode of each keys

Targets of keys

Page

DLP P

ANELINTERFACE FUNCTION

Enter the number of buttons control target, when in single mode only have one targets as default , when In combination mode can

enter multiple, up to 99 .

Signal – ON: only execute a single event on ( only to control a target on)Signal – off: only execute a single event off( only to control a target off)Signal –on/ off: only execute a single event on/off( can control a target on/off)inching: Pressing will on , otherwise off, control single event .Note : control type is common switch and curtain switchCombination On: only execute combination event on ( can control multi-targets on)Combination off: Only execute combination event off( can control multi-targets off)Combination on/off: can execute combination event on/ off ( can control multi-targets on/off)

Key control mode

DLP p

anelStart

programming

1 、 click "combination way”

2 、 Select a Key combination way, The default is the first type, see the picture, in Blue is a combination ， Blue part is combine together, White part is separated

Combination way

example ： In picture A selected the third (3) combination way . see Picture B key one and key two combined into one key. Then press key one or key two , the effect would be same as press key one .In picture B , key 3 and key 4 is combined as one key, then press key three or key four , the effect would be same as press key three . In other combination way , Blue part is combine together and set the first key, the white part is independence to control

Picture A

1

2

1

2

3

4

1 、 set the remark for each

key

2,Input Remark for each Key

3 、 save

DLP P

ANEL

1 、 Click “Mode” to set the mode for each key

2 、 Key mode selection

3 、 save

DLP P

ANEL

Signal – ON: only execute a single event on ( only to control a target on)Signal – off: only execute a single event off( only to control a target off)Signal –on/ off: only execute a single event on/off( can control a target on/off)inching: Pressing will on , otherwise off, control single event .Note : control type is common switch and curtain switchCombination On: only execute combination event on ( can control multi-targets on)Combination off: Only execute combination event off( can control multi-targets off)Combination on/off: can execute combination event on/ off ( can control multi-targets on/off)

Common Key control mode

1 、 Click” Pic download” , set the display content of key

2 、 Select the download status

3 、 Double click the key that need to download pictures. Note The picture format is in BMP ， Size is different according to the combination way, please download see the remark near the button to download correct pictures

DLP P

ANEL

4 、 select Picture from the Pop-up choice box ,need to in BMP Format, please make the Dimensions as per request

5 、 Open

DLP P

ANEL

6 、 download all the selected picture for each button in current status

Signal button download

DLP

7 、 When system pop-up “All download success” ， can check if the display in DLP panel is change

DLP

10 、 download all the selected picture for each button in current status

8 、 select “ On Status” to download the key picture when it is in pressing status

9 、 Double click the key that need to download pictures, the format need to be BMP. Size is different according to the combination way, please download see the remark near the button to download correct pictures

1 、 Click “function” to set

the detail function of each

key

2 、 if it is combination on/off mode ,input the type of the target address which need to be control

3 、 save

DLP P

ANEL

Select AC function

AIR CONDITIONNING CONTROL FUNCTION

select “enable "to start AC function, if it is central AC, Need to enter the AC module address 。Set temperature compensation, compensation for the

difference between display temperature and actual temperature .because according to the installation position ,the temperature would have differences..

Read panel actual status, including temperature , Fan speed. mode and other information , can set the parameters .then click " save" to send control command to panel 。

ON/ Unlock panel AC Control page

To specify the target network or broadcast the panel temperature

DLP P

anel

AC CONTROL FUNCTION

1 、 Make sure “ IR emission replays function” is selected , otherwise can not send the selected information

2 、 Select the model that need to set the control targets

3.set the control targets of each mode ,As picture select "cooling. Heating" .then in information of Air conditioning , need to fill control targets of each temperature value, the type is universal switch

Tip: How to know the control target?Control target is learn air conditioning remote control keys code by IR Learner.Then Upload to SB-EM-IR （ Infrared transmitter ） control code position information.To Know the specific target , just entre the in Infrared transmitter setting interface