InstructIons Photo EtchEd rEPaIr kIt sEt for trumPEtEr ... · [email protected] [email protected]...
9
WWW.RCSUBS.CZ [email protected] INSTRUCTIONS PHOTO ETCHED REPAIR KIT SET FOR TRUMPETER 06801 TYPE: VIIC U-552 1/48
Transcript of InstructIons Photo EtchEd rEPaIr kIt sEt for trumPEtEr ... · [email protected] [email protected]...
[email protected] [email protected] [email protected]
InstructIons Photo EtchEd rEPaIr kIt sEt for trumPEtEr 06801 tyPE: vIIc u-552 1/48
WWW.RCSUBS.CZ [email protected]@seznam.cz
notice:this kit corrects bugs on the u-552 (trumpeter) of the earlier version of the submarine.It fixes the correct number and shape of holes on the hull of the submarine.The set is suitable for building a model where the plexiglass hull will be repaired with brass plates, parts of the plexiglass hull will be carved for good view inside the hull of the submarine. Other areas of plexiglass and brass will be painted in color.
WWW.RCSUBS.CZ
Hull -forming etchingsFor a better shaping of etching, it is necessary to heat up plate and then rapidly cool down.etching is soft and well shaped according to the shape of the hull.Recommendation: Try these steps to shape a different part of the sheet (the rest).
1. 2. 3.
1. fine melting to determine theoutline etching (using solder)
formation of holes using a milling machine2. 3. melting etching into the
hull
4. gluing and kiting
WWW.RCSUBS.CZ
Hull -forming etchingsFor a better shaping of etching, it is necessary to heat up plate and then rapidly cool down.etching is soft and well shaped according to the shape of the hull.Recommendation: Try these steps to shape a different part of the sheet (the rest).
1. 2. 3.
1. fine melting to determine theoutline etching (using solder)
formation of holes using a milling machine2. 3. melting etching into the
hull
4. gluing and kiting
A21A21
v1
v1
v1
v1 a20
a20v4
v1
t1t1
t1
a20
t1
v2
v2 v2v2
v2v2v1 v1
t2
t2v1v2v2v2
v2v2
v2 t3t3t3
t3
G2G2G2
G2G2G2 G2
G2G2G2
G2G2
G2v1
G2
G2
m1
a20
m1m1 m1
[email protected] [email protected] [email protected]
Hull -forming etchingsFor a better shaping of etching, it is necessary to heat up plate and then rapidly cool down.etching is soft and well shaped according to the shape of the hull.Recommendation: Try these steps to shape a different part of the sheet (the rest).
1. 2. 3.
1. fine melting to determine theoutline etching (using solder)
formation of holes using a milling machine2. 3. melting etching into the
hull
4. gluing and kiting
EXAMPLEhull
remove
WWW.RCSUBS.CZ [email protected]@seznam.cz
HULL
WWW.RCSUBS.CZ
Hull -forming etchingsFor a better shaping of etching, it is necessary to heat up plate and then rapidly cool down.etching is soft and well shaped according to the shape of the hull.Recommendation: Try these steps to shape a different part of the sheet (the rest).
1. 2. 3.
1. fine melting to determine theoutline etching (using solder)
formation of holes using a milling machine2. 3. melting etching into the
hull
4. gluing and kiting
WWW.RCSUBS.CZ
Hull -forming etchingsFor a better shaping of etching, it is necessary to heat up plate and then rapidly cool down.etching is soft and well shaped according to the shape of the hull.Recommendation: Try these steps to shape a different part of the sheet (the rest).
1. 2. 3.
1. fine melting to determine theoutline etching (using solder)
formation of holes using a milling machine2. 3. melting etching into the
hull
4. gluing and kiting
left side - 3 holes
- original bad shapes from the Trumpeter
component (HU3) from SKU-0163
[email protected] [email protected] [email protected]
hull
A21 add 3 holes fill
hull - rIGht sIdE
the holes must not be here
WWW.RCSUBS.CZ [email protected]@seznam.cz
hull - lEft sIdE
dEck Gun 88 mm
fill
add 2 holes
the hole must not be here
WWW.RCSUBS.CZ [email protected]
Plexiglass hull
Note: Closed plexiglass hull, the holes can not be cut correctly.It is therefore appropriate to apply new brass plates with correct holes.
glueremove plexiglass
Brass plate A19
News holes
A-A
