Installation Manual - Snap AVInstallation Manual ES-LS-MOUNT-BOX Direct Burial Mounting Box For AT...
Transcript of Installation Manual - Snap AVInstallation Manual ES-LS-MOUNT-BOX Direct Burial Mounting Box For AT...
Installation ManualES-LS-MOUNT-BOX Direct Burial Mounting BoxFor ES-LS-SAT-4 & ES-LS-SAT-6 Loudspeakers
© 2014 Episode®
1. Dig trenches and route the speaker cable or conduit to the speaker location. Dig a hole for the box 3 to 6 inches deep and level the bottom of the hole.
The ES-LS-MOUNT-BOX for Episode® Landscape Speakers is a PVC direct-burial wiring solution that may be used with PVC electrical conduit or direct burial speaker cable. The weatherized wire nuts and optional extensions allow for mounting in nearly any outdoor location.
Included:• (1) ES-LS-MOUNT-BOX• (1) Box Cover• (2) Extension Sleeves• (4) Aluminum Ground Stakes• (8) Stainless Steel Cover Screws
Recommended:• PVC Glue- for PVC conduit or
fittings• Silicone Caulk• Shovel• Hammer• #2 Philip’s Screwdriver• Drill
Installation Instructions
2a. PVC Connection- Knock out the openings to be used with a screwdriver and glue the conduit and box together. Route the cable through the conduit and pull at least 8 inches of cable into the box cavity.
Note: The openings in the box are for 3/4” conduit but other sizes may be used with adapters.
2b. Direct Burial Cable- Drill a hole into the center of the knock out slightly larger than the cable. Route the cable through and pull at least 8 inches of cable into the box cavity. Seal the entrance completely with silicone.
Dig 3-6” deep at box location
(Instructions continued on next page
Important! Ensure all PVC connections are securely glued. Use silicone caulk to seal any openings used for cable. Allow caulk and glue to dry completely before burying the box.
ES
-LS
-MO
UN
T-B
OX
Inst
alla
tio
n M
anua
l
Inst
alla
tio
n In
stru
ctio
ns (
Co
nt’d
)3
. In
stal
l the
loud
spea
ker
to t
he b
ox c
over
. U
se t
he e
xten
sio
ns t
o r
aise
the
sp
eake
r as
ne
eded
. U
se s
ilico
ne in
the
co
uple
r th
read
s to
enh
ance
sea
ling
of
the
box
ag
ains
t m
ois
ture
.
4.
Use
the
wea
ther
pro
of
wir
e nu
ts in
clud
ed
wit
h th
e sp
eake
r to
ter
min
ate
the
wir
ing
co
nnec
tio
ns.
Turn
the
wir
e nu
ts c
lock
wis
e b
y ha
nd u
ntil
they
are
tig
ht.
5.
The
box
may
no
w b
e cl
ose
d.
A
wea
ther
pro
of
gas
ket
is a
ttac
hed
to
the
co
ver,
but
fo
r ad
dit
iona
l wat
er in
trus
ion
pro
tect
ion,
line
the
insi
de
edg
e o
f th
e co
ver
wit
h si
lico
ne w
here
it c
ont
acts
the
box
, th
en a
ssem
ble
the
box
usi
ng t
he 8
scr
ews.
Ti
ght
en t
he s
crew
s ti
ght
ly b
y ha
nd w
ith
a #
2 sc
rew
dri
ver.
6.
Sta
ke t
he b
ox d
ow
n in
the
ho
le s
ecur
ely
usin
g t
he 4
sta
kes.
Ins
tall
all s
pea
kers
and
te
st t
he s
yste
m b
efo
re b
uryi
ng t
he b
oxes
an
d w
irin
g.
7.
Ad
just
the
sp
eake
r an
gle
and
po
siti
on
last
.
© 2
014
Ep
iso
de®
Lifetime Limited WarrantyAll Episode Speaker Products have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA).
© 2014 Episode®
ES-LS-MOUNT-BOX Installation Manual
140304-1200