INSTALLATION MANUAL FOR RAM · INSTLLATION MANAUL FOR RAM Automatic power deploy: The running...
Transcript of INSTALLATION MANUAL FOR RAM · INSTLLATION MANAUL FOR RAM Automatic power deploy: The running...
INSTALLATION MANUAL FOR RAM
INSTALLATION TIME (Hours)
0.5 1 2 3
Professional installation recommend
TOOLS
We highly recommend you to find professional store to install the product.
If not follow the instruction may damage the ECU, motor or the car.
Attention
Wrench tool
Plier
架
Rivet gun
tape
insulating
tape
Attention
Plastic crow plate
crow plate
INSTALLATION MANAUL FOR RAM
Plastic line x1 Wire harness: one set for motor
power and signal
Tie wire x20
Controller
Running boards x2
M6 Gasket x12 M8 Gasket x12
Screw package
M6*25 hexagon screw x12
U-Gasket x10
Drive bracket x2
M8 Nut x12
Driven bracket x4
M8*25 Flange Screw x24
Rear plate x2 Middle plate x2 Front plate x2
M10 rivet nut x4
INSTALLATION MANAUL FOR RAM
1.Installation of Controller,OBD &Wiring
1)Take out the fuse 2)Connecting positive pole with battery
5 ) Fixing the ECU
behind the brake pedal
4)The positive line from here to
cabin
wire to the engine room
6)Use screw to fix controller
Caution! Tighten battery screw very
tight! If loose, may get damage to the car.
INSTLLATION MANAUL FOR RAM
10 ) at driver side, find the CAN
connector, green connector one
11)insert with above green connector,
not the white one.
9)left and right motor line from here
to go inside the cabin. 7)negative connect as above 8)Open the carpet and find the hole
13) plug in all
connecor, use
tape to fix them.
Connect ECU,
insert fuse, then
test the motor
work well or
not.
12)the right side motor line from here
to right side to connect with motor
Car direction (Left side)
DODGE RAM 1500 INSTLLATION MANAUL
2.Install left connection base(Same way for right side)
Tighten all screws !
Left Front Plate Left Rear Plate 2
3
6 5 1
4
8
7 11
10 9
12
1.2.5.6.9.10 Use M8*25 flange screw and M8 nut to fix.
3.4.11.12 Use M8*25 flange screw to fix.
Middle Plate
7.8 use rivet gun and nut to fix.
Car direction (Left side)
INSTLLATION MANAUL FOR RAM
3.Install left brackets(Same way for right side)
KEEP ALL SCREWS A LITTLE LOOSE,
SO THAT BRACKET CAN MOVE WITH
RUNNING BOARD!!!
LF idler bracket
左前从动支架 LRear idler bracket
1
3
2
4
1.2.3.4 Use M8*25 screw to fix,the
same way for other bracket.
LM motor bracket
INSTLLATION MANAUL FOR RAM
4.Install left board (Same way for right side)
Use M6x25 screw and spring washers to fix running board with brackets.
TIGHTEN SCREWS TO FIX BOARD WITH BRAKCETS!
INSTLLATION MANAUL FOR RAM
5. Testing and adjust the balance
3
2 1
FASTEN ALL SCRWS (4x6=24) ON THE 6
BRACKETS
If still not balance, use U shape
washer to adjust it.
4
Insert fuse again. Then open and close doors to let step work.
To assure them up and down freely to adjust position by itself.
INSTLLATION MANAUL FOR RAM
6, Checking all doors activate, the side step work when doors open and close.
Now the installation is finished. Protect all connectors with tap to avoid loose.
To lift the car as
showed
To lift the car
INSTLLATION MANAUL FOR RAM
Automatic power deploy:
The running boards will extend down and out when the door is opened.
Automatic stop:
If an object is in the way of the moving running board, the running board will automatically stop. To reset, clear any obstruction, then
simply open and close the door to resume normal operation.
Manually set in the deployed (OUT) position for access to the roof:
Step your foot while at the same time closing the door. To resume normal operation, open and close the door.
Maintenance: In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running board mechanism,
possibly leading to unwanted noise. If this occurs, manually set the running boards to avoid spraying the motors directly. After
washing, apply silicone spray lubricant to the hinge pivot pins.
Caution! Keep hands and feet away when the running board is in motion.
To changing tire