CivilBay Crane Load Crane Runway Beam Design Crane Runway Girder
Industrial Crane Load Chart US Standard - bmccranes.com€¦ · ic-250-e industrial crane load...
2
IC-250-E Industrial Crane Load Chart US Standard LOAD RADIUS IS THE HORIZONTAL DISTANCE FROM THE CENTER OF ROTATION OF THE UNLOADED CRANE TO THE VERTICAL LOAD LINE WITH THE LOAD APPLIED. EXCEEDING CAPACITY RATINGS OR APPLYING SIDE LOADS TO THE BOOM OR BOOM EXTENSION IS MISUSE,HAZARDOUS, AND VOIDS WARRANTY. CAUTION: BOOM EXTENSION LOADS MUST NOT EXCEED MAIN BOOM CAPACITY. BOOM EXTENSION MAY ONLY CARRY LOADS WITH OUTRIGGERS DOWN. CAPACITIES ON OUTRIGGERS ARE 85% OF TIPPING LOADS. CAPCITIES ON RUBBER ARE 75% OF TIPPING LOADS. CAPACITIES BELOW BOLD LINE ARE LIMITED BY TIPPING. OTHER CAPACITIES ARE LIMITED BY STRUCTURAL OR HYDRAULIC CAPABILITY. MAXIMUM HYDRAULIC PRESSURE: 3000 PSI © 2017 Broderson Manufacturing Corp. www.BMCcranes.com BMC_ic250e-lc_12_16 USE SINGLE PART LOAD LINE FOR LOADS TO 4080KG. WT 82 KG. 1.36 M LOAD LINE FOR WT 136KG. LOADS TO 16330 KG. USE FOUR PART 1.52 M 1.4 M USE TWO PART LOADS TO 8165 KG. LOAD LINE FOR WT 91 KG. Load hooks, downhaul weights, hook blocks and other load handling devices except hoist rope shall be considered part of the load. The load hoist line on this unit must be 9/16” dia. 6x36-EIP-RRL-IWRC wire rope (or equivalent) with a minimum breaking strength of 31,500 lbs.. Approved tires: OTR 385/65D22.5, 16 PLY - 120 PSI Torque wheel nuts to 500 ft. lbs (these conditions must be maintained to handle rated loads on this crane.) Deck load capacity 17,000 lbs, with empty boom retracted over front. Deck load must be centered behind front axle. Speed must be less than 2 MPH. Maximum travel 200 ft. in 30 minutes on smooth pavement. Pick and Carry with the shortest practical boom, centered over the front. Operate with boom as low as possible with the load close to the ground. Pick and Carry capacities are for smooth, level paved surface. The booms on this unit are all steel and have no line voltage rating - No electrical insulation value. Boom extension deduct: 500 lbs. when stowed on base boom. Ensure anti-two-block switch is functional after deploying or stowing boom extension. 15° 7' 5 3/8" 12' 20' 16' 24' 66' 30' RADIUS IN FEET FROM ROTATION TO LOAD 10' 6' 18' 14' 22' 26' 46' 38' 34' 42' 50'54' 62' 58' 70' 72' 48' 36' 32' 28' 44' 40' 60' 56' 52' 68' 64' 79' 6" 76' 30° 50° 40° 75° 70° 60° 0° HEIGHT IN FEET ABOVE GROUND L C L C
Transcript of Industrial Crane Load Chart US Standard - bmccranes.com€¦ · ic-250-e industrial crane load...
IC-250-EIndustrial Crane
Load Chart US StandardLOAD RADIUS IS THE HORIZONTAL DISTANCE FROM THE CENTER OF ROTATION OF THE UNLOADED CRANE TO THE VERTICAL LOAD LINE WITH THE LOAD APPLIED.
EXCEEDING CAPACITY RATINGS OR APPLYING SIDE LOADS TO THE BOOM OR BOOM EXTENSION IS MISUSE, HAZARDOUS, AND VOIDS WARRANTY.
CAUTION: BOOM EXTENSION LOADS MUST NOT EXCEED MAIN BOOM CAPACITY. BOOM EXTENSION MAY ONLY CARRY LOADS WITH OUTRIGGERS DOWN.
CAPACITIES ON OUTRIGGERS ARE 85% OF TIPPING LOADS. CAPCITIES ON RUBBER ARE 75% OF TIPPING LOADS. CAPACITIES BELOW BOLD LINE ARE LIMITED BY TIPPING. OTHER CAPACITIES ARE LIMITED BY STRUCTURAL OR HYDRAULIC CAPABILITY.
MAXIMUM HYDRAULIC PRESSURE: 3000 PSI
© 2017 Broderson Manufacturing Corp.www.BMCcranes.com
BMC_ic250e-lc_12_16
USE SINGLE PARTLOAD LINE FORLOADS TO 4080KG.WT 82 KG.
1.36 M LOAD LINE FOR
WT 136KG.LOADS TO 16330 KG.
USE FOUR PART
1.52 M1.4 M
USE TWO PART
LOADS TO 8165 KG.LOAD LINE FOR
WT 91 KG.
Load hooks, downhaul weights, hook blocks and other load handling devices except hoist rope shall be considered part of the load.
The load hoist line on this unit must be 9/16” dia. 6x36-EIP-RRL-IWRC wire rope (or equivalent) with a minimum breaking strength of 31,500 lbs..
Approved tires: OTR 385/65D22.5, 16 PLY - 120 PSI
Torque wheel nuts to 500 ft. lbs (these conditions must be maintained to handle rated loads on this crane.)
Deck load capacity 17,000 lbs, with empty boom retracted over front. Deck load must be centered behind front axle. Speed must be less than 2 MPH. Maximum travel 200 ft. in 30 minutes on smooth pavement.
Pick and Carry with the shortest practical boom, centered over the front. Operate with boom as low as possible with the load close to the ground. Pick and Carry capacities are for smooth, level paved surface.
The booms on this unit are all steel and have no line voltage rating - No electrical insulation value.
Boom extension deduct: 500 lbs. when stowed on base boom.
Ensure anti-two-block switch is functional after deploying or stowing boom extension.
15°
7' 5 3/8"
12'
20'16'
24'
66'30'RADIUS IN FEET FROM ROTATION TO LOAD
10'6' 18'14' 22'26' 46'38'34' 42' 50'54' 62'58' 70'
72'
48'
36'32'
28'
44'
40'
60'
56'52'
68'64'
79' 6"76'
30°
50°
40°
75° 70°
60°
0°
HE
IGH
T I
N F
EE
T A
BO
VE
GR
OU
ND
LCLC
IC-250-EIndustrial Crane
Load Chart MetricLOAD RADIUS IS THE HORIZONTAL DISTANCE FROM THE CENTER OF ROTATION OF THE UNLOADED CRANE TO THE VERTICAL LOAD LINE WITH THE LOAD APPLIED.
EXCEEDING CAPACITY RATINGS OR APPLYING SIDE LOADS TO THE BOOM OR BOOM EXTENSION IS MISUSE, HAZARDOUS, AND VOIDS WARRANTY.
CAUTION: BOOM EXTENSION LOADS MUST NOT EXCEED MAIN BOOM CAPACITY. BOOM EXTENSION MAY ONLY CARRY LOADS WITH OUTRIGGERS DOWN.
CAPACITIES ON OUTRIGGERS ARE 85% OF TIPPING LOADS. CAPCITIES ON RUBBER ARE 75% OF TIPPING LOADS. CAPACITIES BELOW BOLD LINE ARE LIMITED BY TIPPING. OTHER CAPACITIES ARE LIMITED BY STRUCTURAL OR HYDRAULIC CAPABILITY.
MAXIMUM HYDRAULIC PRESSURE: 207 BAR
© 2017 Broderson Manufacturing Corp.www.BMCcranes.com
BMC_ic250e-lc_12_16
HE
IGH
T I
N M
ET
ER
S A
BO
VE
GR
OU
ND
15°
32.27
23
RADIUS IN METERS FROM ROTATION TO LOAD1312111089645 177 181514 16
24.2
60°
50°
30°
40°
70°75°
456789
1011121314151617181920212223
192021.3LC
LC
USE SINGLE PARTLOAD LINE FORLOADS TO 4080KG.WT 82 KG.
1.36 M LOAD LINE FOR
WT 136KG.LOADS TO 16330 KG.
USE FOUR PART
1.52 M1.4 M
USE TWO PART
LOADS TO 8165 KG.LOAD LINE FOR
WT 91 KG.
Load hooks, downhaul weights, hook blocks and other load handling devices except hoist rope shall be considered part of the load.
The load hoist line on this unit must be 14.3mm dia. 6x36-EIP-RRL-IWRC wire rope (or equivalent) with a minimum breaking strength of 140 kN.
Approved tires: OTR 385/65D22.5, 16 PLY - 825 kPa
Torque wheel nuts to 680Nm (these conditions must be maintained to handle rated loads on this crane.)
Deck load capacity 7,700 kg, with empty boom retracted over front. Deck load must be centered behind front axle. Speed must be less than 3.2 km/h. Maximum travel 60m. in 30 minutes on smooth pavement.
Pick and Carry with the shortest practical boom, centered over the front. Operate with boom as low as possible with the load close to the ground. Pick and Carry capacities are for smooth, level paved surface.
The booms on this unit are all steel and have no line voltage rating - No electrical insulation value.
Boom extension deduct: 220 kg. when stowed on base boom.
Ensure anti-two-block switch is functional after deploying or stowing boom extension.
