Important Electrostatic Discharge and System Grounding … · Important Electrostatic Discharge and...
Transcript of Important Electrostatic Discharge and System Grounding … · Important Electrostatic Discharge and...
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
Revised: September 17, 2012, OL-26782-01
Note This document supports all 3.8.x releases.
OverviewBefore you install the Cisco SCE8000 chassis or touch the modules, read this document.
For more information on installing the Cisco SCE8000 platform, see either the Cisco SCE8000 10GBE Installation and Configuration Guide or the Cisco SCE8000 GBE Installation and Configuration Guide.
For information regarding configuring the Cisco SCE8000 platform, see either the Cisco SCE8000 10GBE Software Configuration Guide or the Cisco SCE8000 GBE Software Configuration Guide.
Americas Headquarters:Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Preparing Your Location
Preparing Your LocationMake sure that your building is correctly grounded to earth ground.
1878
76
Earth ground
2Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Preparing the Rack Room
Preparing the Rack Room• Make sure that the rack enclosures are properly connected to the building earth ground.
• Make sure that the chassis is kept in a sealed antistatic bag prior to installation.
1878
77
Earth ground
Chassis protected in anti-static bag
3Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Preparing Yourself
Preparing YourselfMake sure that you are properly grounded before you remove the antistatic bag from the chassis.
1878
78
Earth ground
4Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Precautions When Unpacking a Chassis
Precautions When Unpacking a ChassisMake sure you are properly grounded when removing the antistatic bag from the chassis.
1878
79Earth ground
5Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Precautions When Installing a Chassis
Precautions When Installing a ChassisMake sure that you are properly grounded and that you properly handle the chassis during installation.
1878
80
Earth ground
6Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Grounding the Chassis
Grounding the Chassis• Make sure you properly connect the chassis (system) ground to the building ground.
• The chassis illustration below shows the system ground connector pad location for the Cisco SCE8000 chassis.
• The ground lug kit part number is 69-0815-01.
2744
87
FAN STATUS
SCM 1
SCM 2
SIP 3
4SCE8000-FAN
SYSTEM POWER
OPTICAL BYPASS
STATUS
AUXPORT 2
LINKACTIVE MASTER
SCE8000 EXTENDED SERVICE CONTROL MODULE
OPTICALBYPASS
OPTICALBYPASS
CONSOLE
10 1001000
LINKACTIVE
PORT 1
A C
A BC D
B D
STATUS
CTRL
OPB-SCE8K-MM
OPTICAL BYPASS1
TX
RX
TX
RX
TX
RX
TX
RX
A C
A BC D
B D
STATUS
CTRL
OPB-SCE8K-MM
OPTICAL BYPASS2
TX
RX
TX
RX
TX
RX
TX
RX
SYSTEM POWER
OPTICAL BYPASS
STATUS
AUXPORT 2
10 1001000
LINKACTIVE MASTER
SCE8000 EXTENDED SERVICE CONTROL MODULE
SCE8000-SCM-E
SCE8000-SCM-E
SCE8000-SIP
CONSOLE
10 1001000
LINKACTIVE
PORT 1
OPTICALBYPASS
OPTICALBYPASS
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
10 1001000
Earthground
7Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Transporting Line Cards
Transporting Line CardsKeep the line card in a sealed antistatic bag when transporting.
1878
82
Earth ground
8Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Handling Line Cards
Handling Line Cards• Properly ground yourself before you remove the line card from the antistatic bag.
• Handle the line card by the front panel and the metal carrier only.
1878
83
Earth ground
9Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Removing and Installing Line Cards
Removing and Installing Line Cards• Make sure you are properly grounded before removing or installing line cards.
• Make sure you properly handle the line card by the front panel and the metal carrier only.
1878
84
Earth ground
10Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Grounding the Work Surface
Grounding the Work Surface• Make sure that you and the work surface that you are placing the line card on are properly grounded.
• Your wrist strap, the rack enclosure, and the work surface should all be attached to the building ground.
2745
32
Earth ground
11Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01
Grounding the Work Surface
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use o f actual IP addresses in illustrative content is unintentional and coincidental.
© 2012 Cisco Systems, Inc. All rights reserved.
12Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x
OL-26782-01