IKH, Tools 2007, 10. Pullers10/4 PULLERS Type 43 self-centering and self-aligning arms •in the...

��

��

10. PULLERS

Arm sets ...................................................................... 7Ball bearing extractors ................................................7Ball joint puller ...........................................................16Ball joint separators ..................................................16Battery terminal puller ..............................................13Bearing fitting tool kit .................................................7Bearing pullers and sets ....................................6-9, 15Bolt/screw extractor set ........................................ 9,15Bush puller pump .......................................................14Clamp spring spreader .............................................13Coil spring clamp pair ...............................................16Disc brake piston reset tool set ................................14Extractors for ball joint .........................................11,16Flange type axle puller ..............................................10Fork separators ..........................................................11Hub pullers .................................................................10Hydraulic rams .............................................................3Internal extractors .......................................................6

Nut splitters .............................................................9,16Piston pin driver .........................................................12Piston ring compressors ......................................12,16Piston ring spreaders ................................................12Puller for cam wheels ................................................13Puller set for v-belt pulleys ........................................13Puller with pressure screw ....................................... 10Pullers .............................................................2-11,13-16Screw extractor set ....................................................15Separators ....................................................................8Slide hammer puller set ............................................15Spring compressor .....................................................11Sprocket holding tool ................................................13Sprocket multi-lock timing device ............................13Steering wheel puller .................................................14Stud pullers/inserters ...........................................10,16Tie rod end puller .......................................................16Valve lifters .................................................................12Wheel hub puller ........................................................15

10/2

PULLERSType 20

•standard type, 2-arms•drop forged steel•interchangeable arms for outside

or inside and centrical andexcentrical pulling

•delivered in pairs (2 pcs)•packing size: 1

PULLERS WITHEXTRA LONG CLAWS, Type 20

PULLER DISPLAY5-pcs Type 20 PLUSKU20STX

Kukkono. 20-STX•can be mounted to the wall•includes 5 pcs of 20 PLUS-serie pullers:

20-1+, 20-10+, 20-2+, 20-20+, 20-3+•packing size: 1EAN 4021176668944

PULLER SET2 and 3-armsType 20/30 SPKUK2030S

Kukko no. K-2030S•includes both two and

three-arm pullers•interchangeable arms for outside or inside and centrical and excentrical

pulling•thin claws 2 mm - can be used

in confined spaces•width 120 mm•includes three arms, depths:

100, 200 and 250 mm•length of bolt / base

137/13 mm•weight 8,5 kg•includes storing box•max. torque 40 Nm•packing size: 1EAN 4021176776021

PULLERType 20 SPKU2010SP•2-arms•interchangeable arms for

outside or inside and cen-trical and excentrical pulling

•thin claws 2 mm - can beused in confined spaces

•width 120 mm•depths of arms:

100, 200 and 250 mm•length of bolt / base

137/13 mm•weight 3,4 kg•max. torque 35 Nm•packing size: 1EAN 4021176461514

PULLERSType 20 PLUSwith quick-adjusting•with knurled knobs for quick

loosening and adjustment ofpuller arms without need of a wrench

•universal type, 2 arms•drop forged steel•interchangeable arms for outside or

inside and centrical and excentrical pulling•guarantee smooth and concentric pulling•long claws ensures good hold on the part to be pulled•packing size: 1

Max.Order no. Kukko Width Depth L/B mm torque Weight EAN

no. mm mm Nm kg

KU201 20-1 90 100 135/17 80 1,1 4021176009433KU2010 20-10 120 100 135/17 80 1,2 4021176009921KU202 20-2 160 150 210/22 150 2,8 4021176009501KU2020 20-20 200 150 210/22 150 3,1 4021176010088KU203 20-3 250 200 280/27 300 7,0 4021176009686KU2030 20-30 350 200 280/27 300 8,0 4021176010163

•guarantee smooth and concentric pulling•long claws ensures good hold on the part to be pulled•packing size: 1

L/B= length of the bolt/base

Order no. Kukko Length Suits Max. Weight EANno. mm torque Nm kg

KU1190P 1-190-P 200 20-1, 20-10 80 1,00 4021176001666KU2300P 2-300-P 300 20-2, 20-20 150 2,15 4021176002731KU3300P 3-300-P 300 20-3 – 20-40 300 4,40 4021176003561

Max.Order no. Kukko Width Depth L/B mm torgue Weigth EAN

no. mm mm Nm kg

KU201X 20-1+ 90 100 135/17 80 1,1 4021176644771KU2010X 20-10+ 120 100 135/17 80 1,2 4021176644856KU202X 20-2+ 160 150 210/22 150 2,8 4021176644931KU2020X 20-20+ 200 150 210/22 150 3,1 4021176645013KU203X 20-3+ 250 200 280/27 300 7,0 4021176645198KU2030X 20-30+ 350 200 280/27 300 8,0 4021176645273

L/B= length of bolt / base

10/3

A

B

PULLER SET 2 and 3-armsType 20 PLUSKUKS20301XSKukkono. KS-2030-1+S•with knurled knobs for

quick loosening and adjustment of puller arms withoutneed of a wrench

•includes both 2 and 3-arms body•interchangeable arms (3 pcs) for outside or inside and

centrical and excentrical pulling•guarantee smooth and concentric pulling•long claws ensures good hold on the part to be pulled•depth 90 mm•width 100 mm•length of bolt/ base 135/17 mm•max. torque 40 Nm•weight 8,5 kg•storing box•packing size: 1EAN 4021176898761

ARM 20/30+KU192E•length 100 mm•alternative for the arm included in set•packing size: 1EAN 4021176669101

PULLERSType 12•3-arms•strong construction, drop-forged steel•high pulling force•with the help of handle the arms open and

close centrally around the part to be pulledwhich ensures non-slip, firm pulling

L/B= length of bolt/base

PULLERSType 30•universal model, 3-arms•drop forged steel•with interchangeable arms for any required

reach - serve both as outside and insidepullers

PULLERType 30 SPKU3010SPKukkono. 30-10-SP•3-arms•with interchangeable arms for any required

reach - serve both as outside and insidepullers

•thin claws 2 mm - for use in confined spaces•width 120 mm•lengths of arms: 100, 200 and 250 mm•length of bolt/ base 137/13 mm•max. torque 40 Nm•weight 4,8 kg•packing size: 1EAN 4021176463839

•the nomimal capacity is reached at a torque of (b) 35 Nm (9-1) or 50 Nm (9-2) respectively,and must not - in order to prevent accidents and damage to the tool - be exceed.

•TO PREVENT OVERLOAD, USE SIZE 3 OR BIGGER PULLERS!

AUXILIARY HYDRAULIC RAMS

Order no. Kukko- Ø Height Shank Pulling Torque Weight EANno. mm mm force tn Nm

KU91 9-1 37 62 10 10 35 0,85 4021176005053KU92 9-2 5 80 12 15 50 1,60 4021176005138

•these rams make a first-class auxiliary tool for boosting the working forceof mechanical pullers applied to particularly stubborn components

•operation: position the ram, with its side pressure screw (b) fully backedoff, between the shaft and the screw (a) and secure by tightening the latter.Initiate hydraulic action by tightening the side pressure screw (b). If the partfails to come off with the first stroke of the arm, continue to work the pullerscrew (a) or proceed as follows: - back off the side pressure screw (b) - retighten the puller screw (a) and the side pressure screw (b)

•after use, back off screw (b) to make the built-in restoring spring returnthe thrust bolt to its initial position

•packing size: 1

•excellent grippingeffect for removingparticularly stubbornball bearings, gears,pulleys etc.

•packing size: 1


no. mm mm Nm kg

KU121 12-1 100 100 135/17 180 1,2 4021176006616KU122 12-2 150 125 175/19 190 1,7 4021176006791KU123 12-3 200 165 230/24 250 3,4 4021176006876

•guarantee smooth and concentric pulling•long claws ensures good hold on the part

to be pulled•packing size: 1L/B= length of bolt/base

Order no. Kukko- Width Depth L/B mm Weight EANno. mm mm kg

KU301 30-1 90 100 135/17 1,3 4021176013393KU3010 30-10 120 100 135/17 1,6 4021176013621KU302 30-2 160 150 210/22 3,5 4021176013478KU3020 30-20 200 150 210/22 3,9 4021176013706KU303 30-3 250 200 280/27 9,0 4021176013546

10/4

PULLERS Type 43 self-centering and self-aligning arms•in the presence of force from the spindle, the

arms clasp the part to be pulled withautomatically increasing intensity

•arms made of drop-forged special steel

2-ARMS

3-ARMS

PULLERS Type 44 self-centering and self-aligning arms•general information on top of the page•sturdy model for removing tightly seated

gears, bearings, pulleys, wheels etc.•packing size: 1

2-ARMS

3-ARMS

2-ARMS

3-ARMS

Autogrip PULLERS Type 482•thanks to integrated self-alignment with

spring mechanism, the gripping powerincreases in proportion to the pullingpower

Order no. Kukko Width Depth L Max. Weight EANno. mm mm mm torque Nm kg

KU431 43-1 60 50 87 25 0,22 4021176015458KU432 43-2 70 70 87 25 0,24 4021176015861

Order no. Kukko Width Depth L Max. Weight EANno. mm mm mm torque Nm kg

KU4311 43-11 60 50 87 25 0,26 4021176015526KU4312 43-12 70 70 87 25 0,30 4021176015601

•due to it’s size suitable especially for maintenanceof small appliances

•for pulling battery shoes, small ball bearings, gears etc.•packing size: 1

L= length of bolt

Order no. Kukko Width Depth L/B Max. Weight EANno. mm mm mm torque Nm kg

KU441 44-1 100 100 130/14 50 0,50 4021176016028KU442 44-2 120 120 160/17 85 0,80 4021176016103KU443 44-3 160 160 210/19 140 1,80 4021176016288


KU451 45-1 100 100 130/14 50 0,60 4021176016448KU452 45-2 120 120 160/17 120 1,10 4021176016516KU453 45-3 160 160 210/19 180 2,30 4021176016691KU454 45-4 250 200 260/24 200 4,00 4021176016776

•the elastic effect incombination with a lean designenables pulling operations inhard-to-access places

•packing size: 1


KU4821 482-1 60 40 T 25 0,20 4021176479779KU4822 482-2 85 90 T 25 0,58 4021176479854KU4824 482-4 200 200 270/13 40 1,38 4021176480096


KU4832 483-2 85 90 T 25 0,36 4021176480331KU4833 483-3 150 150 200/10 35 0,90 4021176480416KU4834 483-4 200 200 270/13 40 1,82 4021176480584

•when tightening the puller, the arms centersand closes around the part to be pulledensuring strong and non-slip pulling grip

•arms made of drop forged steel


T= T-wrench, L/B= length of bolt/base

KU482DB

Width Depth L/B Max. Painomm mm mm torque Nm kg

60 40 T-driver 25 0,2085 90 T-driver 25 0,58

•weight 1,42 kg•packing size: 1EAN 4021176745836

PULLER SET 2-arm, 3-pcs

10/5

PULLERS Type 210

PULLERS Type 201•2-arms, with joint arms•reversible arms - inner and outer pulling•the claws of the arms are narrow from the

other head and wide on the other head

2/3-arms combinationPULLER Type 202KU2031Kukkono. 203-1•2/3-arms, with joint arms•with reversible double-end arms -

inner and outer pulling•the claws of the arms are narrow from the

other head and wide on the other head•made of drop forged steel•arms: width 180 mm, depth 80 mm•length of bolt/base: 135/17 mm•max. torque 75 Nm•weight 1,2 kg•packing size: 1EAN 4021176027741

•2-arms•made of drop forged steel•the claws on the puller have conical blades

on one side to facilitate loosening of suchclosely seated parts as axle bearings, ballbearing races and pinions

•normal claws on the other side

PULLERS Type 204•2-arms•made of drop forged steel•for pulling ball bearings, gears, pinions,

steering arms etc.•the clamp forces the arms tightly up

against the part to be removed


no. mm mm Nm kg

KU2041 204-1 80 90 105/19 100 1,30 4021176028243KU2042 204-2 100 100 130/22 120 2,00 4021176028328KU2043 204-3 150 140 170/24 175 3,00 4021176028403


no. mm mm Nm kg

KU2101 210-1 95 170 210/22 100 2,60 4021176030383KU2102 210-2 135 270 325/24 140 4,30 4021176030468

HydraulicPULLER SET 10-tn,Type 800KU845150Kukkono. 845-150•2 and 3-arms•the set includes: - 3 pcs of arms depth 100 mm,

width 50 – 100 mm - 3 pcs of arms depth 150 mm,

width 75 – 150 mm - 2 and 3-arms body parts - hydraulic ram 10 tons - extension parts 50 and 100 mm - storing box

•when the side clamp is tightened,it forces the claws in under thepart to be pulled, thus prying itaway before the actual pullingprocess

•packing size: 1



no. mm mm Nm kg

KU2011 201-1 150 85 135/17 75 0,90 4021176026591KU2012 201-2 220 130 210/22 150 2,40 4021176026676

•the arms are reversible - inside and outside pulling

•the side clamp forces the claws in behindsuch parts to enable their removal

•packing size: 1


•operation: back off the upper spindle so that the piston can return to its starting position.Place the pressure pad on the thrust bolt and screw the hydraulic ram into the puller’s headsuch that the ram fits up snugly on the shaft. Actuation of the upper spindle increases thepressure and pulls the part off. Attach one or more spindle extension to the thrust bolt if thelength of the hydraulic ram is insufficient. Finally, mount the pressure pad on the spindleextension.

•after use, loosen the hydr. screw•packing size: 1EAN 4021176717871

•made of drop forged steel•packing size: 1


10/6

KU214-KU215KU211-KU213

•for internal pulling of ballbearings, sleeves, bushesetc. even if they fit closelyup to the back of thehousing

•when the bushingexpands the clawstightens under the partto be pulled

•for pulling use thecounterstay no. 22-1

•packing size: 1

INTERNALEXTRACTORSType 21

Order no. Kukkono. Ø mm Weight kg EAN

KU211 21-1 12 –16 0,16 4021176010811KU212 21-2 14 –19 0,18 4021176010996KU213 21-3 18 – 23 0,20 4021176011153KU214 21-4 20 – 30 0,22 4021176011238KU215 21-5 28 – 40 0,36 4021176011498

COUNTERSTAYfor internal extractorsType 22KU221Kukkono. 22-1•drop forged steel•suitable for internal extractors

no. 21-0 - 21-5•incl. reduction collars 21-0 - 21-2

•operation: Push the type 21int.extractor into the bore of thebearing. Tighten nut B to spreadthe jaws C and force the lips D inbehind the rounded race edge.Place the type 22 counterstay onthe bearing housing, and tightenthe screw E down on the extractorscrew A. Now, hold the handle Gfirmly and tighten the nut F toextract the bearing smoothly andevenly. Keep tightening theextractor nut B during the pullingprocess.

•packing size: 1EAN 4021176012228

BALL BEARING PULLERSType 69

BALL BEARINGPULLER SETType 69-AKU69AKukkono. 69-A•for ball bearings ISO 6004 - 6010, 6201 –

6206, 6300 – 6304•width 20–95 mm•2 pcs of arms, pulling L 60 mm•length of bolt/base 137/13 mm•pulling pins: Ø5,3-5,8-8,0 mm•metal case•weight 0,90 kg•packing size: 1EAN 4021176781391

BALL BEARINGPULLER SETType 69-CKU69CKukkono. 69-C•for ball bearings ISO 6021 – 6032, 6212 –

6230, 6309 – 6321, 6406 - 6417•width 56–220 mm•2 pcs of arms, pulling L 250 mm•2 pcs of extension arms

pulling length 250 mm•length of bolt/base 210/22 mm•pulling pins: Ø 16-19-22-25-28-31,75 mm•metal case•weight 7,40 kg•packing size: 1EAN 4021176781544

BALL BEARINGPULLER SETType 69-BKU69BKukkono. 69-B•for ball bearings ISO 6207 – 6211, 6305 –

6308, 6403 - 6405•width 35–120 mm•2 pcs of arms, pulling L 165 mm•length of bolt/base 165/13 mm•pulling pins: Ø 9-11-12,5 mm•metal case•weight 1,90 kg•packing size: 1EAN 4021176781476

Operation: The puller engages the bearing rings. This entailsdestruction of the cage. The spherical segments of the pulling elementsinsert between the inner and outer rings of the bearing. Turning them90 degrees tightens their grip and enables uniform extraction of theball bearing. After screwing the legs of the pulling tools into the pullingelements, fasten them to the head of the puller, and effect pulling bytightening the puller’s pressurescrew against the shaft uponwhich the bearing is mounted.

10/7

•without arms•for quick and easy removal of ball bearings mounted on shafts in housings•packing size: 1

BALL BEARING EXTRACTORS, Type 70

Order the arms for extractors from the table below!

Order no. Kukkono. Suitable arms Weight kg EAN

KU701 70-1 70-711, 70-712, 70-713 0,30 4021176021138KU702 70-2 70-721, 70-722 0,60 4021176021213KU703 70-3 70-731, 70-732 1,20 4021176021398

ARM SETS, Type 70•the set includes 4 pcs of arms•operation: Select the extractor and arms from the table. Insert

the claws between the balls in the outer race of the bearing. Forany bearing marked with an *(asterix), first place a spacer ringcarrying the matching bearing number on the inner bearingrace.Press the upper end of the claws together, so the recesses canengage around the collar of the threaded bushing. Then firmlytighten the clamping plate which in turn pushes the cap over theclaws. Remove the ball bearing by tightening the center screw.

•packing size: 1

Order no. Kukkono. Length mm Extractor For bearings EAN

KU70711 70-711 150 70-1 6000,6001,6002, 6003 4021176021473 6200

KU70712 70-712 150 70-1 *6004, *6005, *6006 4021176021541(6 pcs spacer rings) 6201, *6202, *6203

*6300

KU70713 70-713 170 70-1 *6204, 6205 4021176021626(5 pcs spacer rings) *6301, *6302, *6303

KU70721 70-721 180 70-2 6007, 6008, 6009, 4021176021701(1 pc spacer ring) 6010, *6013

KU70722 70-722 180 70-2 6011, 6012 4021176021886(4 pcs spacer rings) *6206, *6207 *6304, *6306

KU70731 70-731 217 70-3 *6208, *6209, *6210 4021176021961(6 pcs spacer rings) *6307,

*6303, *6407

For any bearing markedwith an *(asterix), first place a spacer ring carrying the matching bearing number on the inner bearing race.

BALL BEARING TOOL SETKU70AKukkono. 70-A•for bearings 6000 - 6013, 6200 - 6212, 6300 - 6311, 6403 - 6408•includes extractors no. 70-1, 70-2, 70-3•3 sets of arms no 70-711, 70-712, 70-713•2 sets of arms no 70-721,70-722•2 sets of arms no 70-731,70-732•1 set of spacer rings = 26 pcs•weight 8,6 kg•packing size: 1EAN 4021176022128

BEARING FITTING TOOL KITKUT071LKukkono. T-071-L•for mounting ball and roller bearings etc.•impact rings made of shock resistant

polyacetate - do not damage the bearing•includes - 33 impact rings: Ø 10-26 - 50-110 mm - impact sleeves: Ø 18, 32 and 52 mm - non-rebounding hammer•weight 4,00 kg•packing size: 1EAN 4021176822483

On pictureextractor +arm set

10/8

KU11320 KU1133

SEPARATORS Type 15•mould forged steel•sharp jaws•press the separator jaws together by tightening the

nuts on both sides•use together with puller Type 18•packing size: 1

Order no. Kukkono. Hole Ø mm Width mm Weight kg EAN

KU150 15-0 5 – 60 60 0,70 4021176006951KU151 15-1 12 – 75 75 1,00 4021176007033KU152 15-2 22 – 115 115 2,5 4021176007118

BEARING PULLER SETType 15KU15A•includes:

- separator, diameter of hole 12–75 mm- pulling tool, width 60–150 mm- extension

•for pulling ball bearings, roller bearings, inner races andother tight-fitting parts

•weight with metal case 4,7 kg•packing size: 1EAN 4021176007521

BEARING PULLER SET10-pcs Type 25KU25B•includes:

- 8 pcs of internal extractors (12–70 mm)- 2 pcs of counterstays

•for pulling out bearings, sleeves, bushes, even bearings that fitclosely up to the back of the housing

•weight with metal case 9,9 kg•packing size: 1EAN 4021176013133

KU1121

KU11210KU112KU11220

KU1123

•arms made of spring steel•self-centering versions centers and closes the arms around the part

to be pulled automatically ensuring strong and non-slip grip•packing size: 1L/B= length of bolt / base

2-ARMS

3-ARMS

BEARING PULLERS Type 112 and 113

Max.Kukko- W D Working L/B torque Weight

Order no. no. mm mm range SKF mm Nm kg EAN

KU11320 113-20 125 100 TMMP 3 X 125 160/17 45 1,10 4021176422423KU1133*) 113-3 185 165 TMMP 3 X 185 220/19 60 2,70 4021176422751*) bent arms

Max.Kukko- W D Working L/B torque Weight

Order no. no. mm mm range SKF mm Nm kg EAN

KU1121 112-1 55 45 TMMP 2 X 55 110/8 25 0,35 4021176418143KU11210 112-10 65 70 TMMP 2 X 65 110/8 25 0,40 4021176415591KU1122 112-2 90 70 TMMP 2 X 90 135/17 55 0,80 4021176419218KU11220 112-20 100 100 TMMP 2 X 100 160/17 55 0,90 4021176420283KU1123 *) 112-3 185 165 TMMP 2 X 170 220/17 65 2,00 4021176420368

*) bent arms

10/9

KU2080 KU2090

PULLER Type 18•mould forged steel•use with a separator•for pulling bearings, gearwheels and gears from confined

spaces•packing size: 1

Order no. Kukkono. W mm D mm L/B mm Weight kg EAN

KU180 18-0 50-110 150 130/14 0,85 4021176075599KU181 18-1 60-150 200 175/19 1,70 4021176075674

PULLERS ”ECONOMY”•made of drop forged steel•with reversible double-end S jaws•packing size: 1

BOLT/SCREW EXTRACTOR SET25-pcsType 49-U-BKU49UBKukkono. 49-U-B•contains:

- 10 pcs of bit guides - bits and torsion studs:

3,2-4,8-6,4-8,0-8,7 mm - nuts 5 pcs•for removing broken bolts and screws•bit guides for easy tapping of broken-off

connectors, even deep inside tapped bores

3. Turn the nutcounterclock-wise smoothly.

NUT SPLITTERS •for splitting jammed or stripped nuts witout damage to the bolt•packing size: 1

Type 54•double-edged models exerting twice the normal splitting force•for nuts in quality classes 5, 6 and 8•packing size: 1

Order no. Kukkono. Nut Weight EAN

KU542 54-2 10 – 27 0,40 4121176170614

Type 55•for splitting nuts in quality class 6 and below•packing size: 1

Order no. Kukkono. Nut Weight EAN

KU551 55-1 10 – 18 0,22 4021176020063KU552 55-2 19 – 27 0,44 4021176020148

1. Drill a holewith the helpof bit guide

2. Pound thetorsion stud intothe hole andpress the inter-nal nut as deepas possible.

Max.Order Kukko- W D P/K torque Weightno. no. Arms mm mm mm Nm kg EAN

KU2080 208-0 2 100 50-75-100 110/8 20 0,35 4021176432248KU2090 209-0 3 100 50-75-100 110/8 20 0,45 4021176432323

•for boltsM5 – M16

•metal case•weight 620 g•packing size: 1EAN 4021176799136

Spare torsion studs:KU49UB-3,2 3,2 mmKU49UB-4,8 4,8 mmKU49UB-6,4 6,4 mmKU49UB-8,0 8,0 mmKU49UB-8,7 8,7 mm

10/10

STUD PULLERS/INSERTERSType 50•the knurled and grooved

clamping wheel presses thestud tightly up against theinternal serration

•a particularly strong,practive-proven model isavailable for maximumstress and strain

•packing size: 1

Order Kukko- For screw Driver Weight EANno. no. mm mm kg

KU501 50-1 5 – 10 17 0,10 4021176019258KU502 50-2 8 – 19 27 0,40 4021176019333KU503 50-3 18 – 25 36 0,60 4121176019418

STUD PULLER/INSERTER SETType 53KU53Kukkono. 53•in the hole which goes through the

socket has 3 gripping rolls whichgrips the inserter when turningclock or counterclockwise

•sizes 6, 8, 10, 12 mm•hexagon 21 mm driver for wrench•1/2“ driver for ratchet wrench•weight 0,78 kg•plastic case•packing size: 1EAN 4021176342233

STUD PULLERS/INSERTERSType 53•hexagon 21 mm driver for wrench•1/2” driver for ratchet wrench•packing size: 1

•made of drop forged steel•a robus puller for passenger cars, vans and trucks with bolthole

diam. up to 225 mm•impact/shock-resistant design•the spindle rests in a self-aligning threaded bushing•packing size: 1

Order no. Kukkono. Arms Weight kg EAN

KU403 40-3 3 4,20 4021176014611KU405 40-5 5 5,14 4021176014956

PULLER withpressure screwKU230SKukkono. 230-S•bolt sizes 4 – 14 mm•for bolthole Ø 100 – 150 mm•pulling by tightening the pressure screw•packing size: 1EAN 4021176893377

FLANGE-TYPE AXLE PULLER Type 230KU230Kukkono. 230•e.g. for pulling parts with tapped bores e.g. spur wheels, knock-out

pins etc. with 4 or 5 studs•once the puller has been attached, effect removal by means of sharp

blows with the slide hammer•for extracting flange axles of AUDI, FORD, OPEL, NISSAN and various

other marks•bolt sizes 4 – 14 mm•for bolthole Ø 100 – 150 mm•weight 3,8 kg•packing size: 1EAN 4021176031038

Order no. Kukkono. Ø Weight kg EAN

KU536 53-6 6 0,14 4021176342318KU538 53-8 8 0,14 4021176342493KU5310 53-10 10 0,22 4021176342561KU5312 53-12 12 0,22 4021176432646

UNIVERSALHUB PULLERSType 40

10/11

EXTRACTORS FOR BALL JOINT Type 128•drop forged steel•for quick and simple extracting of ball

joints•packing size: 1

A = heightB = widthC = opening

L/B = length of bolt/base

EXTRACTORS FOR BALL JOINT Type 129With adjustable jaw opening•drop forged steel•packing size: 1

FORK SEPARATORSType 135•handy tool instead of expensive special-purpose equipment•for removing seized ball pin joints from tapered seats, remo-

ving steering-gear arms, shock absorbers and all other kindsof separating work

•packing size: 1H= width of fork

Order no. Kukkono. H mm Weight EAN

KU1351 135-1 18 0,75 4021176024856KU1352 135-2 23 0,85 4021176024931

•safe, universal spring compressor•equipped with connection clips which keeps the

compressors in position while operation•the bolts are threaded in their whole length•delivered in pairs•packing size: 1

A = RangeC = OpeningP = Size of ball joint

SPRING COMPRESSORType 65, Universal model

Order no. Kukkono. A mm C mm P mm Weight kg EAN

KU1290 129-0 50 20 27 – 30 1,10 4021176410536

•specially designed for the following passanger cars: Audi, BMW, Fiat, Ford, Mercedes-Chrysler,Nissan, Opel, Toyota, VW, Volvo


KU1291 129-1 50 18-22 19 - 27 0,75 4021176024696

•universal type for passenger cars and light commercial vehicles


KU1293A 129-3-A 65 30 35 2,00 4021176803178

•for passenger cars with aluminium chassis e.g. Audi A6 and A8 and other types of vehicleswith confined connecting spaces


KU1293 129-3 70 34 35 – 40 2,50 4021176270949KU1294 129-4 85 40 50 2,60 4021176271021•for medium-size trucks, busses and construction vehicles

KU1290 KU1291 KU1293A KU1293

Order no. Kukkono. A mm B mm C mm L/B Weight kg EAN

KU1281 128-1 38 36 18 40/17 0,30 4021176024108KU1282 128-2 48 45 23 55/17 0,50 4021176024283KU1283 128-3 60 60 29 68/19 1,00 4021176024368

WorkingOrder Kukko- Length range Weightno. no. mm mm Load kg EAN

KU651 65-1 300 110–180 2 tn 2,8 40211760207111

10/12

Order no. Kukkono. A mm Jaws Weight kg EAN

KU1031 103-1 60 – 230 S 1,20 4021176022876•small passenger carsKU1032 103-2 40 – 230 S + T 1,35 4021176022951•small and medium-size passenger carsKU1033 103-3 115 – 290 S + T 3,25 4021176023378•large passenger cars and lightcommercial vehicles

PISTON RING COMPRESSORS Type 100•for tensioning piston rings when fitting pistons and cylinders•packing size: 1

Order no. Kukkono. Piston Ø Height mm Weight kg EAN

KU1000 100-0 40 – 75 50 0,13 4021176428203KU1001 100-1 57 – 125 80 0,28 4021176022203KU1002 100-2 90 – 175 80 0,33 4021176022388

PISTON RING SPREADERSType 101•for spreading piston rings when mounting them into the piston or

when removing them from the piston•packing size: 1

Order no. Kukkono. Piston Ø Length mm Weight kg EAN

KU1011 101-1 50 – 100 200 0,25 4021176022531KU1012 101-2 90 – 150 240 0,37 4021176022616

VALVE LIFTERS•for assembling valves•packing size: 1

A= openingS= straight jawsT= curved jaws

PISTON PIN DRIVER100 mmType 102KU1021•Ø 100 mm•enable easy, gentle removal and installation

of piston pins without damage to the piston•fits for all motors of passenger cars and

motor bicycles•with three supplementary pressure pads•weight 0,15 kg•packing size: 1EAN 4021176022791

KU1033

KU1031

KU1032

10/13

SPROCKET HOLDING TOOLKUT144Kukkono. T-144•universal type, for most passenger vehicles•for safe loosening of the fastening nuts of cam and feed

pump - set the tool into the holes of gear, hold back andloosen the nut with suitable wrench, this way no damagewill cause to the engine

•for rotating the camshaft e.g. when adjusting the valves•weight 1,00 kg•packing size: 1EAN 4021176893353

SPROCKET MULTI-LOCKTIMING DEVICEKUT143Kukkono. T-143•universal type for both double camshaft engines

and the V-engines equipped with four camshafts•for diesel engines in which the cam gear and feed

pump gear are close with each other•for locking the sprocket while changing the timing

belt•weight 0,32 kg•packing size: 1EAN 4021176893346

PULLER SET FORV-BELT PULLEYSKU124KKukkono. 124-K•2-arms•for V-belt pulleys up to Ø 195 mm•the set includes: - 2 pullers widths 132 and 195 mm - 2 arms depth 68 mm - 2 arm extension pieces 20 mm - 2 holding screws for extension pieces - 3 pressure pads ( different lengths ) - storing box•weight 2,84 kg•packing size: 1EAN 4021176736841

BATTERY TERMINALPULLER Type 41-1KU411Kukkono. 41-1•2-arms, jointed•basic model for pulling off

battery terminals and othersmall parts

•width 65 mm•depth 65 mm•max. torque 25 Nm•weight 0,20kg•packing size: 1EAN 4021176015038

CLAMP SPRINGSPREADERKU1190Kukkono. 119-0•VW and Audi•for mounting and

removing clamp spring onand from the sphericalflanges of exhaust system


PULLER FOR CAM WHEELSKU1180Kukkono. 118-0•AUDI/VW TDI 4, 6 and 8-cylinder diesel engines•AUDI/VW V6 and V8 gasoline engines•from year model 1998 and on•includes 2 pcs of 1-jaw arms•includes 2 pcs of 2-jaws arms•weight 1,20 kg•packing size: 1EAN 4021176860904

10/14

STEERING WHEELPULLERKU341Kukkono. 34-1•2-arms, universal model•for new-model steering

wheels with ample pullingslots

•arms 87 mm and 135 mm•width 35 – 90 mm•length of bolt 134 mm, base

17 mm•weight 0,65 kg•packing size: 1EAN 4021176865886

DISC BRAKE PISTONRESET TOOL SETKU12630Kukkono. 126-30•includes 6 adapters for universal accommodation of old and new-model European and

Japanese vehicles•set includes: pressure screw, guide bush, pressure plate, 7 pcs of turn-back adapters,

metal case•turn-back adapters: VW-Audi, Seat, Skoda, Ford, BMW, Mercedes, Toyota, Nissan and

Mitsubishi•adapters for disc brakes which are equipped with integrated parking brake: VW-Audi,

Seat, Skoda, Ford, Rover 200, 400, 800, Saab, Jaguar XJ6, Peugeot, Nissan, Subaru,Mitsubishi, Mazda, Honda Civic, Citroen, Opel Astra and Vectra


BUSH PULLER PUMPType 9KUKH93•power 10 KN•length of stroke 30 mm•hole Ø 20,5 mm•height 74 mm

•for installing wheel bearings, installingand removing of bushes


GEARPULLERS

•with turnablearms– possibilityfor outer and innerpulling

3-ARMS:2-in-1GEAR PULLER SET75 mmIKH7059•turnable arms – possibility for

inner and outer pulling•can be used as 2- or 3-armed•packing size: 1/48EAN 6418914705975

2-ARMS:

Order Size Pack.no. mm size EAN

IKH7055 75 1/60 6418914705937IKH7056 100 1/40 6418914705944IKH7057 150 1/20 6418914705951IKH7058 200 1/8 6418914705968

Order Size Pack.no. mm size EAN

IKH7051 75 1/60 6418914705890IKH7052 100 1/50 6418914705906IKH7053 150 1/30 6418914705913IKH7054 200 1/12 6418914705920

10/15

PULLER SET for bearingsIKH51

chrome-vanadium-steelcontains:- bearing separators 6–60 mm and 13–60 mm- bar puller 38–127 mm- 2 pcs of push-puller legs with extensionsplastic casepacking size: 1/5

EAN 6418914694705

••

••

5-armWHEEL HUB PULLER 90–180 mmIKH7126

metal casepacking size: 1/6

EAN 6418914649323

••

PULLER SETIKH52

chrome-vanadium-steelbody parts for 2-arm-pullers and 3-arm-pullerslengths of arm sets 31, 47, 123 mmplastic casepacking size: 1/6

EAN 6418914694712

•••••

BEARINGPULLER SETIKH7096

puller plates 50–75 mm and 75–100 mm,chrome-molybdenum-steelframe part made of carbon steelpuller leg pairs with extension bar (60 + 90 mm and 80 + 110 mm)tension bolt 160 mmmetal casepacking size: 1/5

EAN 6418914709508

•

•••••

SLIDE HAMMERPULLER SETX009042

for loosening bearings, belt pulleys, chain pulleys and different kind of hubspacking size: 1/2

EAN 6418914149991

•

•

SCREWEXTRACTORSETIKH7218

content:- HSS-drills 5 pcs: 3,2 • 4,8 • 6,4 • 8 • 8,7 mm- guide bushings 10 pcs: B1 • B2 • B3 • B4 • B5 • B6 • B7 • B8 B9 • B10- extractor pins 5 pcs: C1 • C2 • C3 • C4 • C5- extractor nuts 5 pcs: D1 • D2 • D3 • D4 • D5plastic casepacking size: 1/24

EAN 641891464912

•

••

BEARING PULLER SET+ SLIDE HAMMERIKH7390

content:Puller Bearing size8 mm 8-10 mm10 mm 10-12 mm12 mm 12-14 mm15 mm 15-17 mm

•Puller Bearing size17 mm 17-20 mm20 mm 20-24 mm25 mm 25-29 mm30 mm 30-32mm

handle length 390 mmhammer length 100 mm, hammer weight 940 gpacking size: 1/5

EAN 6418914547391

•••

BEARING/SEALINSTALLERSET 15-pcsIKH7377

12,6/17,4 mm - 85,6/90,5 mmbearings and sealspacking size: 1/2

EAN 6418914547261

•

•

14.7.2008

10/16

STUD PULLERSOCKET SETIKH7107•chrome-vanadium steel•socket sizes: 1/4” (6 mm)

5/16” (8 mm)3/8” (10 mm)7/16” (12 mm)

•max. socket torque:- 1/4” (6 mm ) = 20 Nm- 5/16” (8 mm) = 20 Nm- 3/8” (10 mm) = 33 Nm- 7/16” (12 mm) = 33 Nm

•packing size: 1/24EAN 6418914709614

BALL JOINT SEPARATORSBALL JOINTPULLERIKH7060•opening 50 mm, capacity 19 mm•packing size: 1/40EAN 6418914705982

PISTON RINGCOMPRESSORS•material spring steel•for compressing the piston rings

into grooves for mountingthe piston to cylinder

•includes hex key

IKH7023•for pistons Ø 45 – 90 mm•height 50 mm•packing size: 1/20/120EAN 6418914705319

IKH7024•for pistons Ø 90 – 175 mm•height 80 mm•packing size: 1/20/60EAN 6418914705326

STUDREMOVERIKH7007•driver 1/2”•for Ø 6,35–20 mm bolts•eccentric-operation•packing size: 1/6EAN 6418914695832

TIE RODEND PULLERXAT1151•opening 16–44 mm•width 50 mm•height 70 mm•packing size: 1/25EAN 6418914609792

COIL SPRING CLAMP PAIR280 mmXTB1142•max. clamping distance 280 mm•packing size: 1/20EAN 6418914621053

X005684•for

14–27 mm nuts•packing size:

1/8/48EAN6418914610026

NUTSPLITTERSX005683•for

5–20 mm nuts•packing size:

1/10/60EAN6418914610019

300 mmIKH7085•packing size: 1/6/36EAN 6418914706224

400 mmIKH7086•packing size: 1/6/36EAN 6418914706231

COIL SPRINGCLAMP PAIRIKH7014•with two jaws•length 300 mm, width of jaws

90 mm•packing size: 1/8EAN 6418914695986

COIL SPRINGCOMPRESSOR PAIRHeavy DutyIKH7292•single jaws•length 280 mm, thickness 25 mm•width of jaws 30 mm•packing size: 1/6EAN 6418914519503

IKH, Tools 2007, 10. Pullers10/4 PULLERS Type 43 self-centering and self-aligning arms •in the...

Documents

Transcript of IKH, Tools 2007, 10. Pullers10/4 PULLERS Type 43 self-centering and self-aligning arms •in the...