IC-7200 Manual
Transcript of IC-7200 Manual
-
8/7/2019 IC-7200 Manual
1/104
INSTRUCTION MANUAL
HF/50 MHz TRANSCEIVER
i7200
-
8/7/2019 IC-7200 Manual
2/104
IMPORTANT
READ THIS INSTRUCTION MANUALCAREFULLYbeore attempting to operate thetransceiver.
SAVE THIS INSTRUCTION MANUAL. Thismanual contains important saety and operating in-structions or the IC-7200.
FOREWORD
We understand that you have a choice o many dier-ent radios in the market place. We want to take a cou-
ple o moments o your time to thank you or makingthe IC-7200 your radio o choice, and hope you agreewith Icoms philosophy o technology irst. Manyhours o research and development went into the de-sign o your IC-7200.
DFEATURES
IF DSP features Digital Twin PBT Manual notch function 0.5 ppm of high frequency stability Simple operation Tough and compact body Standard voice synthesizer
EXPLICIT DEFINITIONS
WORD DEFINITION
RWARNINGPersonal injury, ire hazard or electric
shock may occur.CAUTION Equipment damage may occur.
NOTEI disregarded, inconvenience only. No risk
o personal injury, fre or electric shock.
SUPPLIED ACCESSORIES
The transceiver comes with the ollowing accessories.
Qty.qHand microphone (HM-36) ............................. 1wDC power cable (OPC-1457) .......................... 1eSpare use (ATC 5 A) ...................................... 1rSpare use (ATC 30 A) .................................... 2t ACC cable ......................................................... 1y 3.5 (d) mm plug ................................................. 1u 6.3 (d) mm Electronic keyer plug ...................... 1
i Microphone hanger ........................................... 1
o Jack cap (or [PHONES]) ................................. 1
q
e
t
w
y u
r
i o
FCC INFORMATION
FOR CLASS B UNINTENTIONAL RADIATORS:This equipment has been tested and ound to complywith the limits or a Class B digital device, pursuant topart 15 o the FCC Rules. These limits are designedto provide reasonable protection against harmul in-tererence in a residential installation. This equipmentgenerates, uses and can radiate radio requency en-ergy and, i not installed and used in accordance withthe instructions, may cause harmul intererence to
radio communications. However, there is no guaran-tee that intererence will not occur in a particular in-stallation. I this equipment does cause harmul inter-erence to radio or television reception, which can bedetermined by turning the equipment o and on, theuser is encouraged to try to correct the intererenceby one or more o the ollowing measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment
and receiver. Connect the equipment into an outlet on a circuit
dierent rom that to which the receiver is con-nected. Consult the dealer or an experienced radio/TV
technician or help.
Icom, Icom Inc. and the logo are registered trademarks oIcom Incorporated (Japan) in the United States, the United King-
dom, Germany, France, Spain, Russia and/or other countries.Microsot, Windows and Windows Vista are either registered trade-
marks or trademarks o Microsot Corporation in the United States
and/or other countries.
All other products or brands are registered trademarks or trade-
marks o their respective holders.
i
-
8/7/2019 IC-7200 Manual
3/104
PRECAUTIONS
RWARNING RF EXPOSURE! This device emitsRadio Frequency (RF) energy. Extreme caution
should be observed when operating this device. Iyou have any questions regarding RF exposure andsaety standards please reer to the Federal Com-munications Commission Oice o Engineering andTechnologys report on Evaluating Compliance withFCC Guidelines or Human Radio Frequency Electro-magnetic Fields (OET Bulletin 65).
RWARNING HIGH VOLTAGE! NEVER touch anantenna or internal antenna connector during trans-mission. This may result in an electrical shock or burn.
RWARNING! NEVER operate the transceiverwhile driving a vehicle. Sae driving requires your ullattentionanything less may result in an accident.
RNEVER apply AC power to the [DC13.8V] socketon the transceiver rear panel. This could cause a reor damage the transceiver.
RNEVER apply more than 16 V DC, such as a 24 Vbattery, to the [DC13.8V] socket on the transceiverrear panel. This could cause a ire or damage thetransceiver.
RNEVER let metal, wire or other objects touch anyinternal part or connectors on the rear panel o thetransceiver. This may result in an electric shock or thiscould cause a re or damege the transceiver.
RNEVER expose the transceiver to rain, snow orany liquids.
DO NOT use or place the transceiver in areas withtemperatures below 10C (+14F) or above +60C(+140F). Be aware that temperatures on a vehiclesdashboard can exceed +80C (+176F), resulting in
permanent damage to the transceiver i let there orextended periods.
DO NOT place the transceiver in excessively dustyenvironments or in direct sunlight.
DO NOT place the transceiver against walls or putanything on top o the transceiver. This will obstructheat dissipation.
Place unit in a secure place to avoid inadvertent useby children.
During mobile operation, NEVER place the trans-ceiver where air bag deployment may be obstructed.
During mobile operation, DO NOT place the trans-
ceiver where hot or cold air blows directly onto it.
During mobile operation, DO NOT operate the trans-ceiver without running the vehicles engine. When thetransceivers power is ON and your vehicles engineis OFF, the vehicles battery will quickly become ex-hausted.
Make sure the transceiver power is OFF beore start-ing the vehicle engine. This will avoid possible dam-age to the transceiver by ignition voltage spikes.
During maritime mobile operation, keep the trans-ceiver and microphone as ar away as possible romthe magnetic navigation compass to prevent errone-ous indications.
BE CAREFUL! The rear panel will become hot whenoperating the transceiver continuously or long peri-ods.
BE CAREFUL! I a linear ampliier is connected, setthe transceivers RF output power to less than thelinear ampliers maximum input level, otherwise, thelinear amplier will be damaged.
Use Icom microphones only (supplied or optional).Other manuacturers microphones have dierent pinassignments, and connection to the IC-7200 maydamage the transceiver.
For U.S.A. onlyCaution: Changes or modiications to this trans-ceiver, not expressly approved by Icom Inc., couldvoid your authority to operate this transceiver underFCC regulations.
ii
-
8/7/2019 IC-7200 Manual
4/104
iii
TABLE OF CONTENTS
IMPORTANT............................................................... i
FOREWORD .............................................................. iEXPLICIT DEFINITIONS............................................ i
SUPPLIED ACCESSORIES....................................... i
FCC INFORMATION .................................................. i
PRECAUTIONS......................................................... ii
TABLE OF CONTENTS ....................................... iii-iv
1 PANEL DESCRIPTION................................... 111
Front panel ........................................................ 1
D Keypad .......................................................... 5
Function display ................................................ 7
Rear panel ......................................................... 9
D ACC socket inormation .............................. 10 Microphones .................................................... 11
D HM-36 ......................................................... 11
D SM-20 ......................................................... 11
2 INSTALLATION AND CONNECTIONS ........ 1220
Unpacking ....................................................... 12
Selecting a location ......................................... 12
Grounding ....................................................... 12
Antenna connection ........................................ 12
Required connections...................................... 13
Advanced connections .................................... 14
Power supply connections ............................... 15
Connecting the DC Power Supply ................... 15
Battery connections ......................................... 15
External antenna tuners .................................. 16
Linear amplier connections............................ 17
Connections or CW ........................................ 18
Connections or RTTY ..................................... 19
D Connections or RTTY (FSK) ...................... 19
D Connections or RTTY (AFSK) .................... 19
Connections or SSTV or PSK31 .................... 20
DWhen connecting to the [ACC] socket ......... 20
DWhen connecting to the [MIC] connector .... 20 DWhen connecting to the [USB] jack ............. 20
3 BASIC OPERATION ..................................... 2132
Beore rst applying power .............................. 21
Applying power (CPU resetting) ...................... 21
VFO description ............................................... 22
VFO operation ................................................. 22
D Selecting the VFO A/B ................................ 22
D VFO equalization......................................... 22
Selecting VFO/memory mode ......................... 23
D Dierences between VFO mode and
memory mode ............................................. 23
Selecting an operating band ........................... 24
D Using the band stacking register ................. 24 Frequency setting ............................................ 25
D Using the main dial ..................................... 25
D Direct requency entry with keypad ............. 25
D Programmable tuning steps ........................ 26
D Selecting the programmable tuning step..... 26
D 1 Hz and 10 Hz tuning steps ....................... 27
D TS switch fow chart ................................. 27
D Auto tuning step unction ............................ 28
D tuning unction
(SSB data/CW/RTTY only) ......................... 28
DBand edge warning beep ............................ 28 Volume setting ................................................. 29
Operating mode selection ............................... 29
Dial lock unction ............................................. 29
RF gain and Squelch ....................................... 30
Meter unction ................................................. 30
Basic transmit operation .................................. 31
D Transmitting ................................................. 31
DOutput power and Microphone gain settings... 31
Voice synthesizer unction ............................... 32
4 RECEIVE AND TRANSMIT .......................... 3343
Operating SSB ................................................ 33 D Convenient unctions or receive ................. 33
D Convenient unctions or transmit ................ 34
D About 5 MHz band operation
(USA version only) ...................................... 34
Operating CW ................................................. 35
D Convenient unctions or receive ................. 36
D Convenient unctions or transmit ................ 36
D CW reverse mode ....................................... 37
D CW pitch control.......................................... 37
D CW side tone unction ................................. 38
D Keying speed setting ................................... 38
Operating RTTY (FSK) .................................... 39
D Convenient unctions or receive ................. 39
D RTTY reverse mode .................................... 40
D Twin peak lter ............................................ 40
D RTTY decode set mode .............................. 41
Operating AM .................................................. 42
D Convenient unctions or receive ................. 42
D Convenient unctions or transmit ................ 42
Data mode (SSTV/PSK31) operation .............. 43
-
8/7/2019 IC-7200 Manual
5/104
5 FUNCTIONS FOR RECEIVE ........................ 4452
RIT unction ..................................................... 44 Preamp and attenuator ................................... 45
AGC unction ................................................... 45
D AGC time constant selection ....................... 45
Twin PBT operation ......................................... 46
IF lter selection .............................................. 47
D IF lter selection .......................................... 47
D FIlter passband width setting ...................... 48
D IF Ilter shape (SSB/CW only) ..................... 48
Noise blanker .................................................. 49
D Noise blanker settings ................................. 49
Noise reduction ............................................... 50
D Noise reduction level setting ....................... 50
Notch unction ................................................. 51
D Auto notch unction ..................................... 51
D Manual notch unction ................................. 51
D Manual notch lter setting ........................... 52
6 FUNCTIONS FOR TRANSMIT ..................... 5360
VOX unction.................................................... 53
D Adjusting the VOX unction.......................... 53
D VOX set mode ............................................. 54
Break-in unction ............................................. 55
D Semi break-in operation .............................. 55 D Full break-in operation ................................ 56
Speech compressor ........................................ 57
D Compression level setting ........................... 57
Split requency operation ................................ 58
D Quick split unction ...................................... 59
D Split lock unction ........................................ 59
Measuring SWR .............................................. 60
7 MEMORY OPERATION ................................ 6164
Memory channels ............................................ 61
Memory channel selection .............................. 61
Memory programming ..................................... 62 D Programming in VFO mode ........................ 62
D Programming in memory mode...................62
Frequency copying .......................................... 63
D Copying in memory mode ........................... 63
Memory clearing ............................................. 64
8 SCAN OPERATION ...................................... 6566
Scan types ...................................................... 65
Preparation ...................................................... 65
Programmed scan operation (VFO mode) ...... 66
Memory scan operation (Memory mode) ........66
9 ANTENNA TUNER OPERATION ................. 6769
Optional AT-180 automaticantennatuneroperation ......................................................... 67
D Tuner operation ........................................... 67
D Manual tuning ............................................. 67
AT-180 internal switch description ................... 68
Optional AH-4 automaticantennatuner
operation ......................................................... 69
D AH-4 operation ............................................ 69
10 SET MODE ................................................... 7082
General ........................................................... 70
D Quick set mode operation ........................... 70
D Set mode operation ..................................... 70 Quick set mode ............................................... 71
Set mode ......................................................... 74
D Paddle operation rom [MIC] connector ...... 82
11 MAINTENANCE ........................................... 8384
Fuse replacement ........................................... 83
D DC power cable use replacement .............. 83
D Circuitry use replacement .......................... 83
Memory backup ............................................... 84
Resetting the CPU .......................................... 84
Cleaning .......................................................... 84
12 TROUBLESHOOTING .................................. 8586
13 OPTION INSTALLATIONS ................................. 87
MB-116 handles installation ........................... 87
MB-117 carryinghandle installation ............. 87
MB-118 mobilemountingbracketinstallation..87
14 CONTROL COMMAND ................................ 8891
Remote jack (CI-V) inormation ....................... 88
D CI-V connection example ............................ 88
D Data ormat ................................................. 88
D Command table ........................................... 89 D Band stacking register ................................ 91
D Data mode with lter width setting .............. 91
15 SPECIFICATIONS .............................................. 92
General ........................................................... 92
Transmitter ....................................................... 92
Receiver .......................................................... 92
16 OPTIONS ...................................................... 9394
17 ABOUT CE ................................................... 9596
18 BAND VOLTAGE MODIFICATION...................... 97 Band voltage modication ............................... 97
iv
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
-
8/7/2019 IC-7200 Manual
6/104
qPASSBAND TUNING CONTROLS [TWIN PBT]Adjust the receivers DSP ilter passband width.(p. 46) The limit o the variable range depends on the pass-
band width and mode. The limit o the variable range
is hal o the passband width, and PBT is adjustable in200 Hz (AM) or 50 Hz (other models) steps.
Rotate both [TWIN PBT] controls (PBT1 and PBT2) to
the same position shits the IF.
4What is the PBT control?Generally, the PBT electronically narrows the IFpassband width to reject intererence. This trans-ceiver uses the DSP circuit or the PBT unction.
PBT2
PBT1
Low cutHigh cut Center
TWIN PBT TWIN PBT TWIN PBT
+
wNOISE BLANKER KEY NB (p. 49) Push to turn the noise blanker unction ON or
OFF.
appears on the display.
Push and hold or 1 sec to enter the noise
blanker set mode or setting the noise blankerlevel and blank time; push again to return to nor-mal operation. When entering the noise blanker set mode, the noise
blanker unction is automatically turned ON.
4What is the noise blanker?The noise blanker reduces pulse-type noise suchas that generated by automobile ignition systems.This unction is not eective against non pulse-typenoise.
eNR KEY NR (p. 50) Push to turn the noise reduction unction ON orOFF.
appears on the display.
Push and hold or 1 sec. to enter the noise re-duction level set mode; push again to return tonormal operation. When entering the noise reduction set mode, the
noise reduction unction is automatically turned ON.
4What is the Noise Reduction function?The Noise Reduction (NR) unction removes ran-dom noise rom the receiver passband. The level is
adjustable to allow maximum clarity without harm-ing the intelligibility o the desired signal. Noise Re-duction should generally not be used with digitalmodes.
1
1
PANEL DESCRIPTION
i7200
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENTBANDGENE
9
.
AGCMW
AN FMETERNRNB
Speakertrew
FunctionDisplay (p. 7)
ui y
q
o
Front panel
-
8/7/2019 IC-7200 Manual
7/104
-
8/7/2019 IC-7200 Manual
8/104
3
!0MODE KEY MODE (p. 29) Push momentarily to cycle through the operating
modes:USB/LSB CW/CW-R RTTY/RTTY-R AM
Push and hold or 1 sec. to toggle the ollowing
operating modes:USB LSB (p. 33)CW CW-R (Reverse) (p. 35)RTTY RTTY-R (Reverse) (p. 39) CW-R or RTTY-R appears on the display when
reverse mode is selected.
Undesired modes can be inhibited in set mode.(p. 81)
!1TUNING STEP KEY TS (pgs. 26, 27) Push to turn the programmable tuning step ON
or OFF.
appears above the 1 kHz indicator when the pro-grammable tuning step is turned ON and the re-
quency can be changed in programmed kHz steps.
While the programmable tuning step is turnedON ( appears), push and hold or 1 sec. toenter tuning step set mode; push again to returnto normal operation. 0.1, 1, 5, 9 and 10 kHz programmable tuning steps
are available.
While the programmable tuning step is turnedOFF, push and hold or 1 sec. to turn the 1 Hzstep ON and OFF. 1 Hz indication appears, and the requency can be
changed in 1 Hz steps.
!2PREAMP/ATTENUATOR KEYP.AMP
ATT (p. 45) Push to turn the preamp ON or OFF.
appears on the display.
Push and hold or 1 sec. to turn the 20 dB atten-uator ON; push momentarily to turn the attenua-
tor OFF. appears on the display.
4What is the preamp?The preamp ampliies signals in the receiver rontend (input) circuit to improve the sensitivity. Turnthe preamp ON when receiving weak signals.
4What is the attenuator?The attenuator prevents a strong undesired signalnear the desired requency or near your location,such as rom a broadcast station, rom causing dis-tortion or spurious signals.
!3MAIN DIAL [DIAL]Changes the displayed requency and selects val-ues or selected set mode items, etc.
!4FILTER KEY FILTER (p. 47) Push momentarily to cycle the IF ilter settings
between wide, middle and narrow or the se-lected operating mode.
Push and hold or 1 sec. to enter the ilter setmode.
i7200
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENTBANDGENE
9
.
AGCMW
AN FMETERNRNB
SpeakerFunctionDisplay (p. 7)
!3@1 !5 !4!6!7!9 !8@0
!1!0
!2
Front panel (Continued)
1 PANEL DESCRIPTION
-
8/7/2019 IC-7200 Manual
9/104
4
1PANEL DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
!5SPCHLOCK KEYSPCH
Push to announce the selected requency and
S-meter level by the speech synthesizer. (p. 32) The parameters to be announced can be selected in
the set mode. (p. 77)
Push and hold or 1 sec. to turn the dial lockunction ON or OFF. (p. 29)
The dial lock unction electronically locks the main
dial.
appears while the dial lock unction is ON.
!6POWER KEY Push to turn power ON.
Turn the DC power supply ON in advance.
Push and hold or 1 sec. to turn power OFF.
!7TUNER KEY TUNER (p. 67) Push to turn the automatic antenna tuner unc-
tion ON or OFF. An optional antenna tuner must be connected.
appears on the display.
Push and hold or 1 sec. to manually tune theantenna tuner. An optional antenna tuner must be connected.
When the tuner cannot tune the antenna, the tuning
circuit is bypassed automatically ater 20 sec.
!8RF GAIN/SQUELCH CONTROL[RF/SQL](outer control; p. 30) Adjusts the RF gain and squelch threshold level.
The squelch removes noise output rom thespeaker (closed condition) when no signal is re-ceived. The squelch is available or all modes.
The control can be set as the squelch plus RF gaincontrols, squelch control only (RF gain is ixed at
maximum) or Auto (RF gain control in SSB, CW and
RTTY; squelch control in AM) in set mode.
MODESET MODE SETTING
AUTO SQL RF + SQL
SSB, CW
RTTYRF GAIN SQL RF GAIN + SQL
AM SQL SQL RF GAIN + SQL
Minimum RF gain
Adjustable range
RF gain adjustable
range
Maximum RF gain
Maximum RF gain
Squelch is open. S-meter squelch
S-meter squelch
threshold
Lowest threshold Highest threshold
Squelch is open.
S-meter squelch
S-meter squelch
threshold
When functioning as RF GAIN/SQL control
When functioning as RF GAIN control(Squelch is fixed open; SSB, CW, RTTY only)
When functioning as SQL control(RF gain is fixed at maximum.)
!9AF CONTROL [AF] (inner control; p. 29)Varies the audio output level rom the speaker.
Audio output
decreases
Audio output
increases
@0HEADPHONE JACK [PHONES]Accepts headphones with 816 impedance. Output power: 5 mW with an 8 load.
When headphones are connected, no receive audiocomes rom the speaker.
@1MICROPHONE CONNECTOR [MIC]Accepts supplied or optional microphone. See p. 11 or appropriate microphones and microphone
connector inormation.
-
8/7/2019 IC-7200 Manual
10/104
-
8/7/2019 IC-7200 Manual
11/104
-
8/7/2019 IC-7200 Manual
12/104
7
q TRANSMIT INDICATORAppears while transmitting.
w MODE INDICATORSShows the selected operating mode. appears when SSB/AM data mode is se-
lected. (p. 71)
-R appears when CW reverse or RTTY reversemode is selected. (pgs. 29, 35, 39)
e IF FILTER INDICATORS (p. 47)Shows the selected IF lter.
appears when the wide IF lter is selected.
appears when the normal IF ilter is se-lected.
appears when the narrow IF ilter is se-lected.
r LOCK INDICATOR (p. 29)Appears when the dial lock unction is activated.
t MEMORY INDICATOR (p. 61)
Appears when memory mode is selected.
y MEMORY CHANNEL NUMBER READOUT(p. 61)Shows the selected memory channel number.
u BLANK INDICATOR (p. 62)Appears when the selected memory channel isblank.
This indicator appears both in VFO and memory mode.
i SIGNAL/SQL/RF-GAIN METER Shows receiving signal strength while receiving.
Shows either transmit power meter (Po), SWRor ALC while transmitting. (p. 30)
o NOTCH INDICATORS (p. 51) appears when the automatic notch unc-
tion is activated. appears when the manual notch unction
is activated.
!0 NOISE REDUCTION INDICATOR (p. 50)Appears when the noise reduction is activated.
!1 NOISE BLANKER INDICATOR (p. 49)Appears when the noise blanker is activated.
!2 TUNE INDICATOR (p. 67) Appears when the optional automatic antenna
tuner is activated. Blinks while tuning.
!3 RECEIVE INDICATORAppears while receiving a signal or when thesquelch is open.
!4 FREQUENCY READOUTShows the operating requency.
Function display
q w e r
t
i
u
y
!1 o!0
!2
!3
!4
1 PANEL DESCRIPTION
-
8/7/2019 IC-7200 Manual
13/104
8
1PANEL DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
!5 PROGRAMMABLE TUNING STEP INDICATOR Appears when the programmable tuning step is
selected. (p. 26)
!6 RIT INDICATOR (p. 44)Appears when the RIT unction is activated.
!7 VFO INDICATORS (p. 22)VFO A or VFO B appears when VFO mode isselected.
!8 FUNCTION INDICATORS appears when the speech compressor
is activated in SSB mode. appears when the VOX unction is acti-
vated. appears during split requency opera-
tion. appears when preamp is activated. appears when the attenuator unction is
activated. appears during scan.
Blinks when scan is paused.
!9 AGC INDICATORS (p. 45)Shows the selected AGC time constant. F.AGC or AGC ast; AGC-OFF or AGC OFF; no in-
dicator; or AGC slow.
@0BREAK-IN INDICATORS (p. 55) BK appears when the semi break-in unction is
activated. F-BK appears when the ull break-in unction
is activated.
!5 !6
!7
!8
!9
@0
-
8/7/2019 IC-7200 Manual
14/104
-
8/7/2019 IC-7200 Manual
15/104
-
8/7/2019 IC-7200 Manual
16/104
11
MICROPHONE CONNECTOR
(Front view)
y GND (PTT ground)
t PTT
r Squelch switch
q Microphone input
w +8 V DC output
e Frequency up/down
i AF output(varies with [AF])
u GND(Microphone ground)
[MIC]
PIN NO.FUNCTION DESCRIPTION
w +8 V DC output Max. 10 mA
eFrequency up Ground
Frequency down Ground through 470
rSquelch open LOW level
Squelch close HIGH level
CAUTION: DO NOT short pin 2 to ground asthis can damage the internal 8 V regulator. DCvoltage is applied to pin 1 or microphone opera-
tion. Use caution when using a non-Icom micro-phone.
HM-36 SCHEMATIC DIAGRAM
+
q
w
ert
y
u
i
4700pF
0.33F
MICROPHONE
MIC
ELEMENT
2k
470
DOWN UP
PTT RECEIVE
TRANSMIT
MICROPHONE CABLE MICROPHONE PLUG
1k+
10F
q UP/DOWN SWITCHES [UP]/[DN]Change the selected readout requency or memory
channel. Pushing the switch continuously changes the requency
or memory channel number continuously.
The [UP]/[DN] switch can simulate a key paddle. Select
in set mode (U/D KEY; Mic Up/Down Keyer). (p. 80)
While pushing and holding RIT *, push the [UP]/[DN]
switch to control the transmit readout requency while
in spilt requency operation.
* Available only when the XFC (transmit requency
check) unction is turned ON. (p. 76)
w PTT SWITCHPush and hold to transmit; release to receive.
e PTT LOCK SWITCH (SM-20 only)Push to lock the PTT switch to the transmissioncodition.
q
w
q
we
Microphones
D HM-36
D SM-20(Option)
1 PANEL DESCRIPTION
-
8/7/2019 IC-7200 Manual
17/104
-
8/7/2019 IC-7200 Manual
18/104
-
8/7/2019 IC-7200 Manual
19/104
-
8/7/2019 IC-7200 Manual
20/104
-
8/7/2019 IC-7200 Manual
21/104
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
External antenna tuners
CONNECTING THE AH-4
GroundGround
Long wire or optional AH-2b
AH-4[ANT]
IC-7200
Coaxial cable(from the AH-4)
[TUNER]
CONNECTING THE AT-180
IC-7200
Ground
AT-180
HF
to 6 m
antenna
[TRANSCEIVER]
[ANT][ANT][ACC] [ACC]
ACC cable supplied with the AT-180
Coaxial cable suppliedwith the AT-180
Either of the twoexternal connectors
Ground
Turn the IC-7200s power OFF when connectingthe AT-180, otherwise, the CPU may malunctionand the AT-180 may not unction properly.
2INSTALLATION AND CONNECTIONS
-
8/7/2019 IC-7200 Manual
22/104
-
8/7/2019 IC-7200 Manual
23/104
-
8/7/2019 IC-7200 Manual
24/104
-
8/7/2019 IC-7200 Manual
25/104
-
8/7/2019 IC-7200 Manual
26/104
-
8/7/2019 IC-7200 Manual
27/104
-
8/7/2019 IC-7200 Manual
28/104
-
8/7/2019 IC-7200 Manual
29/104
-
8/7/2019 IC-7200 Manual
30/104
-
8/7/2019 IC-7200 Manual
31/104
26
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
D Programmable tuning steps
D Selecting the programmable tuning step
Programmable tuning steps are available to suit youroperating requirements.These tuning steps are: Selectable rom 0.1, 1, 5, 9 and 10 kHz
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL]
q Push TS to turn the programmable tuning unc-tion ON. Z appears.
Programmable tuning step indicator
w Push and hold TS or 1 sec. to enter the tuningstep set mode.
e Rotate [DIAL] to select the desired tuning step
rom 0.1, 1, 5, 9 or 10 kHz.r Push TS to exit the tuning step set mode.t Rotate [DIAL] to change the requency according
to the set tuning step.
y Push TS to turn the programmable tuning unc-tion OFF. Z disappears.
The operating requency can be changed in steps o(0.1, 1, 5, 9 or 10 kHz selectable) or quick tuning.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL]
q Push TS to turn the programmable tuning unc-tion ON. Z appears.
Programmable tuning step indicator
w Rotate [DIAL] to change the requency in pro-grammed kHz steps.
e Push TS again to turn the programmable tuning
unction OFF. Z disappears.
r Rotate [DIAL] or normal tuning, i desired.
3BASIC OPERATION
-
8/7/2019 IC-7200 Manual
32/104
-
8/7/2019 IC-7200 Manual
33/104
-
8/7/2019 IC-7200 Manual
34/104
-
8/7/2019 IC-7200 Manual
35/104
30
3BASIC OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
RF gain and Squelch
Meter unction
The [RF/SQL] control adjusts the RF gain andsquelch threshold level. The squelch stops noise out-
put rom the speaker (closed position) when no sig-nal is received. The 12 oclock position is recommended or any setting
o the [RF/SQL] control.
The [RF/SQL] control can be set as the RF gain control
only (squelch is xed open) or squelch control (RF gain is
xed at maximum) in the set mode (p. 75). See the table
as below.
MODESET MODE SETTING
AUTO SQL RF + SQL
SSB, CW
RTTYRF GAIN SQL RF GAIN + SQL
AM SQL SQL RF GAIN + SQL
Adjusting RF gain (Receive sensitivity)Normally, the [RF/SQL] control is set to the 12 oclockposition.Rotate the [RF/SQL] control to the 11 oclock posi-tion or maximum sensitivity. Rotate the [RF/SQL] control clockwise to increase, coun-
terclockwise to decrease the receiver sensitivity.
The S-meter indicates receive sensitivity.
Adjusting squelch (Removing non-signal noise)
Rotate the [RF/SQL] control to the 1 oclock posi-tion to invoke the S-meter squelch this allows youto set the minimum signal level needed to open thesquelch. A segment appears in the S-meter to indicate the S-me-
ter squelch level.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[RF/SQL]
Minimum RF gain
Adjustable range
RF gain adjustablerange
Maximum RF gain
Maximum RF gain
Squelch is open. S-meter squelch
S-meter squelch
threshold
Squelch is open.
S-meter squelch
S-meter squelch
threshold
When functioning as RF GAIN/SQL control
When functioning as RF GAIN control
When functioning as SQL control
Lowest Threshold Highest Threshold
The transceiver has 3 transmit meter unctions oryour convenience. Select the desired meter rom RFpower (Po), ALC and SWR.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETER
NRNB
Push and holdANF
METER or 1 sec. to toggle betweenRF power (Po), SWR and ALC. The display indication changes as the ollowing table.
DISPLAY
INDICATIONMEASUREMENT
Po Indicates the relative RF output power.
SWR Indicates the SWR on the transmission line.
ALC
Indicates the ALC level. When the meter
movement shows the input signal level
exceeds the allowable level, the ALC lim-its the RF power. In such cases, reduce
the MIC gain setting (see p. 31) in the
quick set mode.
-
8/7/2019 IC-7200 Manual
36/104
-
8/7/2019 IC-7200 Manual
37/104
-
8/7/2019 IC-7200 Manual
38/104
-
8/7/2019 IC-7200 Manual
39/104
34
4RECEIVE AND TRANSMIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
D Convenient unctions or transmit
VOX (voice operated transmit) (p. 53) Push VOX to turn the VOX unction ON or OFF.
appears when the VOX unction is ON.
Push and hold VOX or 1 sec. to enter the VOXset mode, then rotate [DIAL] to adjust the VOXgain, anti VOX gain or VOX delay. Rotate [M-CH] to select an item.
Speech compressor (p. 57) Push COMP to turn the speech compressor ON
or OFF. appears when the speech compressor is ON.
Push and hold COMP or 1 sec. to enter the com-pression level set mode, then rotate [DIAL] to ad-just the compression level.
D About 5 MHz band operation (USA version only)
Operation on the 5 MHz band is allowed on 5 dis-crete requencies and must adhere to the ollowing:
USB mode Maximum o 50 watts ERP (Eective Radiated Power)
2.8 kHz bandwidth
It is the operators responsibility to set all controls sothat the transmission in this band meets the stringentconditions under which we may use these requen-cies.
NOTE: We recommend that you store these re-quencies, mode and ilter settings into the mem-ory channel or easy recall.
IC-7200
Display Frequency*
FCC Channel
Center Frequency*
5.33050 MHz 5.33200 MHz
5.34650 MHz 5.34800 MHz
5.36650 MHz 5.36800 MHz
5.37150 MHz 5.37300 MHz
5.40350 MHz 5.40500 MHz
*The channel center requencies that are speciiedby the FCC, show the center requency o theirpassband. However, the IC-7200 displays carrierpoint requency, so set 1.5 kHz below rom FCCchannel center requency.
To assist you in operating the 5 MHz band cor-rectly within the rules speciied by the FCC,transmission is impossible on any 5 MHz bandrequency other than the 5 requencies indicated inthe table above.
-
8/7/2019 IC-7200 Manual
40/104
35
Operating CW
q Connect a paddle, straight key or external elec-tronic keyer as on page 18.
w Push and hold F-INP ENTBAND or 1 sec., then push aband key to select the desired band.
e Push MODE to select CW mode.
Ater CW mode is selected, push and hold MODE or
1 sec. to toggle between CW and CW-R modes.
r Rotate [DIAL] to tune in a desired signal with thedesired tone requency. The S-meter indicates received signal strength when
signal is received.
t Rotate the [AF] control to set audio to a comort-able listening level.
y Set CW break-in operation and the CW delay time
in the set mode. (p. 79)q Push and hold
M-CH/RITSET or 1 sec. twice to enter
the set mode.
w Rotate [M-CH] to select BK-IN to set the CWbreak-in operation.
e Rotate [DIAL] to select the CW break-in opera-tion rom ull break-in, semi break-in or OFF. FL : ull break-in
SE : semi break-in
OF : break-in OFF
r Rotate [M-CH] to select BK-DELAY to selectthe CW delay time when semi break-in operation
is selected in stepe
.t Rotate [DIAL] to set the desired delay time.
y Continue to set the keyer settings in the setmode, i necessary. (p. 80)
u Push M-CH/RITSET to exit the set mode and return tonormal operation.
u Keying to transmit, use the paddle, straight key orexternal electronic keyer to send your CW signals. appears.
The Po meter indicates the transmit power strength.
i Stop keying to return to receive.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
Band keys
[DIAL][AF]
CW or CW-R appears.
Appears while transmitting.
[M-CH]
Appears when semi break-in is selected.
4 RECEIVE AND TRANSMIT
-
8/7/2019 IC-7200 Manual
41/104
-
8/7/2019 IC-7200 Manual
42/104
-
8/7/2019 IC-7200 Manual
43/104
-
8/7/2019 IC-7200 Manual
44/104
-
8/7/2019 IC-7200 Manual
45/104
40
4RECEIVE AND TRANSMIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
D RTTY reverse mode
Received characters are occasionally garbled whenthe receive signal is reversed between MARK andSPACE. This reversal can be caused by incorrectTNC connections, settings, commands, etc.
To receive a reversed RTTY signal correctly, selectRTTY-R (RTTY reverse) mode.
qPush MODE to select RTTY mode.
wAter RTTY mode is selected, push and holdMODE or 1 sec. to toggle between RTTY and
RTTY-R modes.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETER
NRNB
ReverseNormal
BFO
170
Hz
2125
Hz
170
Hz
2125
Hz
BFO
MarkSpace
Displayed freq.Displayed freq.
MarkSpace
DTwin peak lter
The twin peak ilter changes the receive requencyresponse by boosting two particular requencies
(2125 and 2295 Hz) or better copying o desired RTTY
signals.
qPush MODE to select RTTY mode. Ater RTTY mode is selected, push and hold MODE
or 1 sec. to toggle between RTTY and RTTY-R modes.
w Push and hold M-CH/RITSET or 1 sec. to enter thequick set mode.
e Rotate [M-CH] to select TPF, then rotate [DIAL]to select the twin peak lter unction ON or OFF. The received audio volume may become greater when
the twin peak lter is turned ON.
r PushM-CH/RIT
SET to exit the quick set mode and re-
turn to normal operation.
OFF (default)
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH]
-
8/7/2019 IC-7200 Manual
46/104
41
4 RECEIVE AND TRANSMIT
D RTTY decode set mode
Set the RTTY key polarity, shit width and mark tone.
qWhen RTTY (RTTY-R) mode is selected, push andhold M-CH/RITSET or 1 sec. to enter the quick set mode.
w Rotate [M-CH] to select the desired set item.
e Rotate [DIAL] to adjust the desired value or con-dition. Push and hold M-CL or 1 sec. to return to the deault
value.
r PushM-CH/RIT
SET to exit the quick set mode and re-turn to normal operation.
[DIAL]
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[M-CH]
RTTY mark tone (RTTY mode)
This item selects the RTTY mark requency. RTTY markrequency is switched between 1275, 1615 and 2125 Hz.
2125 Hz (default)
RTTY shit width (RTTY mode)
This item adjusts the RTTY shit width. There are 4selectable values: 170, 200, 425 and 850 Hz.
170 Hz (default)
RTTY key polarity (RTTY mode)
This item selects the RTTY keying polarity. Normal orreverse keying polarity can be selected.When reverse polarity is selected, Mark and Space arereversed.n (normal) : Key open/close = Mark/Space
r (reverse) : Key open/close = Space/Mark
NORMAL (default)
-
8/7/2019 IC-7200 Manual
47/104
42
4RECEIVE AND TRANSMIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
Operating AM
q Push and holdF-INP ENT
BAND or 1 sec., then push aband key to select the desired band.
w Push MODE to select AM mode.e Rotate [DIAL] to tune in a desired signal.
The S-meter indicates received signal strength when a
signal is received.
The deault tuning step or AM mode is 1 kHz; this
can be changed using the tuning step program mode.
(p. 26)
r Rotate the [AF] control to set audio to a comort-able listening level.
t Push [PTT] (microphone) to transmit. appears.
y Speak into the microphone at your normal voicelevel.
Adjust MIC Gain at this step, i necessary. (p. 71)u Release [PTT] (microphone) to return to receive.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL][AF]
Appears while transmitting.
F-INPENT
BAND
Band keys
AM appears.
D Convenient unctions or receive
Preamp and attenuator (p. 45)
PushP.AMP
ATT to turn the preamp ON or OFF.
appears when the preamp is set to ON.
Push and hold P.AMPATT or 1 sec. to turn the attenu-ator ON.
PushP.AMP
ATT to turn the attenuator OFF.
appears when the attenuator is set to ON.
AGC (auto gain control) (p. 45)
Push AGC once or twice to select the time con-stant or the AGC circuit ast and slow. F.AGC appears when the ast time constant is se-
lected, and no indicator appears when the slow time
constant is selected, respectively.
Push and hold AGC or 1 sec. to turn the AGCunction OFF. AGC-OFF appears on the display.
Noise blanker (p. 49)
Push NB to turn the noise blanker ON or OFF. appears when the noise blanker is set to ON.
Push and hold NB or 1 sec. to enter the noiseblanker set mode, then rotate [DIAL] to adjust thethreshold level, or the blank time. Rotate [M-CH] to select an item.
Twin PBT (passband tuning) (p. 46)
Rotate [TWIN PBT] (controlsinner/outer).
Noise reduction (p. 50)
Push NR to turn the noise reduction ON or OFF. appears when the noise reduction is ON.
Push and hold NR or 1 sec. to enter the noise
reduction level set mode, then rotate [DIAL] toadjust the noise reduction level.
Manual notch lter (pgs. 51, 52)
Push MNF to turn the manual notch lter ON orOFF. appears when the manual notch ilter is set to
ON.
Push and hold MNF or 1 sec. to enter the man-ual notch lter set mode, then rotate [DIAL] to se-lect the lter width rom narrow, middle and wide.
Auto notch lter (p. 51) Push
ANFMETER to turn the auto notch ilter ON or
OFF. appears when the auto notch ilter is set to
ON.
D Convenient unctions or transmit
VOX (voice operated transmit) (p. 53)
Push VOX to turn the VOX unction ON or OFF. appears when the VOX unction is ON.
Push and hold VOX or 1 sec. to enter the VOXset mode, then rotate [DIAL] to adjust the VOX
gain, anti VOX gain or VOX delay. Rotate [M-CH] to select an item.
-
8/7/2019 IC-7200 Manual
48/104
-
8/7/2019 IC-7200 Manual
49/104
-
8/7/2019 IC-7200 Manual
50/104
-
8/7/2019 IC-7200 Manual
51/104
-
8/7/2019 IC-7200 Manual
52/104
47
5 FUNCTIONS FOR RECEIVE
IF lter selection
The transceiver has 3 passband IF ilter widths oreach mode.
For SSB and CW modes, the passband width can beset rom 50 to 3600 Hz in 50 or 100 Hz steps.A total o 41 passband widths are available.
For RTTY mode, the passband width can be set rom50 to 2700 Hz in 50 or 100 Hz steps.A total o 32 passband widths are available.
For AM mode, the passband width can be set rom200 to 8000 Hz in 200 Hz steps.
A total o 40 passband widths are available.
The ilter selection is automatically memorized ineach mode.
D IF lter selection
q Push MODE several times to select the desired
mode.w Push FILTER several times to select the IF ilter
rom Wide, Middle or Narrow. The selected IF ilter indicator ( , or )
appears in the LCD.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETER
NRNB
Selected IF filter indicator
-
8/7/2019 IC-7200 Manual
53/104
48
5FUNCTIONS FOR RECEIVE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
D FIlter passband width setting
q Push MODE several times to select the desiredmode.
w Push and hold FILTER or 1 sec. to enter lter setmode.
e Rotate [M-CH] to select FIL.
r Push FILTER several times to select the desiredIF lter.
t Rotate [DIAL] to set the desired passband width. The passband width can be set within the range as
shown in the table at right below.
Push and hold M-CL or 1 sec. to return to the deault
value.
y Repeat stepsr andt i desired.
u Push and hold FILTER or 1 sec. to exit the ilterset mode.
When the IF passband width is set to minimum bythe [TWIN PBT] controls (when one control ismax. counterclockwise, and the other one is max.clockwise; p. 46), a sound may not come rom thespeaker depending on the IF lter passband widthsetting. This is not a transceivers malunction.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH]
Mode Filter Deault Range (Steps)
SSB
Wide 3000 Hz50500 Hz (50 Hz)/
6003600 Hz (100 Hz)Middle 2400 Hz
Narrow 1800 Hz
SSB Data/
CW
Wide 1200 Hz50500 Hz (50 Hz)/
6003600 Hz (100 Hz)Middle 500 Hz
Narrow 250 Hz
RTTY
Wide 2400 Hz50500 Hz (50 Hz)/
6002700 Hz (100 Hz)Middle 500 Hz
Narrow 250 Hz
AM/
AM Data
Wide 8000 Hz
2008000 Hz (200 Hz)Middle 6000 Hz
Narrow 3000 Hz
D IF Ilter shape (SSB/CW only)
The type o DSP lter shape or SSB and CW can beselected independently rom sot and sharp.
q Push MODE several times to select SSB or CW
mode.w Push and hold FILTER or 1 sec. to enter lter set
mode.e Rotate [M-CH] to select SHAPE.
r Push FILTER several times to select the desiredIF lter rom Wide, Middle or Narrow.
t Rotate [DIAL] to select the desired ilter shape,either sot or sharp
Push and hold M-CL or 1 sec. to return to the deault
value.
y Push and hold FILTER or 1 sec. to exit the ilterset mode.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATT
P.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH]
Sharp
Soft
-
8/7/2019 IC-7200 Manual
54/104
49
5 FUNCTIONS FOR RECEIVE
Noise blanker
The noise blanker eliminates pulse-type noise suchas rom car ignition systems.
Push NB to turn the noise blanker ON or OFF.
appears when the NB unction is ON.
When using the noise blanker, received signalsmay be distorted i they are excessively strong orthe noise type is other than impulse. Nearbystrong signals can also cause the noise blanker tocreate distortion. Turn the noise blanker unctionOFF, or adjust the noise blanker level to a shal-lower setting (see below) in this case.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETER
NRNB
Appears
D Noise blanker settings
q Push and hold NB or 1 sec. to enter the noiseblanker set mode.
The noise blanker is turned ON and appears.
w Rotate [M-CH] to select the desired set item.
e Rotate [DIAL] to adjust the desired condition.
Push and hold M-CL or 1 sec. to return to the deaultvalue.
r Push NB to exit the noise blanker set mode.
t Push NB to turn the noise blanker OFF i neces-sary.
disappears.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH]
Appears
NB LEVEL
This item adjusts the noise blanker level. The noiseblanker attenuation level can be adjusted rom 0% to
100%.
50% (default)
NB WIDTH
This item allows adjustment o the blank time or noiseblanker to match the pulse width. The noise blanker widthcan be adjusted rom 1% to 100%.
50% (default)
-
8/7/2019 IC-7200 Manual
55/104
50
5FUNCTIONS FOR RECEIVE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
Noise reduction
The noise reduction enhances desired signals inthe presence o noise by using the DSP circuit to re-move random noise. The amount o enhancement isadjustable.
Push NR to turn the noise reduction ON or OFF.
appears when the NR unction is ON.
The noise reduction level can result in audio sig-nal masking. Set the noise reduction level ormaximum readability as described below.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETER
NRNB
Appears
Noise reduction OFF
NR Level 0
Noise reduction is activated
NR Level 4 (default)
Desired
signal (CW)
Noise components
D Noise reduction level setting
q Push and hold NR or 1 sec. to enter the noisereduction level set mode. The noise reduction is turned ON and appears.
w Rotate [DIAL] to adjust the noise reduction level. The noise reduction level can be adjusted rom 0 to
15.
Push and hold M-CL or 1 sec. to return to the deault
value.
e Push NR to exit the noise reduction set mode.r Push NR to turn the noise reduction OFF i nec-
essary.
disappears.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL]
4 (default)
Appears
-
8/7/2019 IC-7200 Manual
56/104
51
5 FUNCTIONS FOR RECEIVE
Notch unction
This transceiver has auto and manual notch unc-
tions.The auto notch unction automatically attenuatesbeat tones, tuning signals, changing requency, etc.,even i they are moving.The manual notch can be set to attenuate a re-quency via the [MNF] control.
PushANF
METER to turn the auto notch unction ON or
OFF. appears when the auto notch unction is ON. The auto notch unction is available while in SSB or
AM mode.
Push MNF to turn the manual notch unction ONor OFF. appears when the manual notch unction is
ON.
While in SSB or AM mode, either the auto or manual
notch unction can be turned ON. These unctions are
selected by pushing ANFMETER or MNF .
Manual notch ilter setting is described on the next
page.
D Auto notch unction
The auto notch can be used in SSB and AM modes.
PushANF
METER to turn the automatic notch unctionON or OFF. appears when the auto notch unction is ON.
Unwanted interference
Desiredsignal (AF)
Desiredsignal (AF)
Interference frequency
is attenuated
Auto notch OFF Auto notch ON
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETER
NRNB
Appears
D Manual notch unction
Push MNF to turn the manual notch unction ON
or OFF. appears when the manual notch unction is
ON.
Set to attenuate a requency or manual notch via the
[MNF] control.
Set the requency or manual notch iltering via the
manual notch ilter set mode. (described on the next
page)
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
Appears
[MNF]
-
8/7/2019 IC-7200 Manual
57/104
52
5FUNCTIONS FOR RECEIVE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
D Manual notch lter setting
q Push and hold MNF or 1 sec. to enter the man-ual notch lter set mode. The manual notch unction is turned ON and
appears.
w Rotate [DIAL] to select the ilter width rom nar-row, middle and wide.
Push and hold M-CL or 1 sec. to return to the deault
value.
e Push MNF to exit the manual notch ilter setmode.
r Push MNF to turn the manual notch unctionOFF i necessary.
disappears.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL]
Middle (default)
While adjusting the manual notch lter, noise maybe heard. This comes rom the DSP unit and doesnot indicate an equipment malunction.
-
8/7/2019 IC-7200 Manual
58/104
6
53
FUNCTIONS FOR TRANSMIT
VOX unction
The VOX (Voice-Operated Transmission) unctionuses your voice to switch between transmit andreceive. This unction provides an opportunity orhands-ree operation or to input log entries into yourcomputer, etc., while operating.
q Push MODE to select a phone mode (SSB orAM). When SSB mode is selected, push and hold MODE
or 1 sec. to toggle between USB and LSB modes.
w Push VOX to toggle the VOX unction ON andOFF. appears when the VOX unction is ON.
The VOX gain, ANTI-VOX and VOX delay can be setin VOX set mode. (See below.)
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH] VOX289
Appears
D Adjusting the VOX unction
q Push MODE to select a phone mode (SSB orAM). When SSB mode is selected, push and hold MODE
or 1 sec. to toggle between USB and LSB modes.
w Push VOX to toggle the VOX unction ON andOFF. appears when the VOX unction is ON.
eAdjust the VOX unctions in the VOX set mode.
q Push and hold VOX or 1 sec. to enter the VOXset mode.
w Rotate [M-CH] to select VoX GAIN.
eWhile speaking into the microphone with yournormal voice level, rotate [DIAL] to the pointwhere the transceiver is continuously transmit-ting.
r Rotate [M-CH] to select ANTI-Vox.t During receive, rotate [DIAL] to adjust the anti-
VOX gain to the point where the transceiver
does not switch to transmit due to receivedaudio rom the speaker.
y Rotate [M-CH] to select VoX DELY.
u Rotate [DIAL] to adjust the VOX delay or aconvenient interval beore returning to receive.
i Push VOX to exit the VOX set mode. and returnto normal operation.
VOX Gain
50% (default)
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH] VOX 289
-
8/7/2019 IC-7200 Manual
59/104
54
6FUNCTIONS FOR TRANSMIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
D VOX set mode
VOX GAINThis item adjusts the VOX gain or the VOX (Voice-Oper-ated Transmission) unction. Higher values make the VOXunction more sensitive to your voice.This setting can be adjusted rom 0% to 100% in 1%steps.
Push and hold M-CL or 1 sec. to return to the deault value.50% (default)
ANTI-VOX
This item adjusts the ANTI-VOX gain or the VOX (Voice-Operated Transmission) unction. Higher values make theVOX unction less sensitive to receiver output audio roma speaker or headphones.This setting can be adjusted rom 0% to 100% in 1%steps.
Push and hold M-CL or 1 sec. to return to the deault value.
50% (default)
VOX DELAY
This item adjusts the VOX (Voice-Operated Transmission)delay time. VOX Delay is the amount o time the transmit-ter stays on ater you stop speaking.The delay time can be adjusted rom 0 to 2.0 sec. in 0.1sec. steps.
Push and hold M-CL or 1 sec. to return to the deault value.
0.2 sec. (default)
-
8/7/2019 IC-7200 Manual
60/104
55
6 FUNCTIONS FOR TRANSMIT
Break-in unction
The break-in unction is used in CW mode to auto-matically switch the transceiver between transmit and
receive when keying. The IC-7200 is capable o ullbreak-in or semi break-in. Break-in operation is alsoreerred to as QSK.
D Semi break-in operation
During semi break-in operation, the transceiver im-mediately transmits when keying, then automati-cally returns to receive ater a pre-set delay time haspassed rom when you stop keying. This is similiar toVOX operation or voice.
q Push MODE to select CW or CW-R mode. When CW mode is selected, push and hold MODE
or 1 sec. to toggle between CW and CW-R modes.
wSet the semi break-in unction ON in the set mode.
q Push and hold M-CH/RITSET or 1 sec. twice to enterthe set mode.
w Rotate [M-CH] to select BK-IN to set the CWbreak-in operation.
e Rotate [DIAL] to select SE. FL : Full break-in
SE : Semi break-in
OF : Break-in OFF
r Rotate [M-CH] to select BK-DELAY to selectthe CW delay time when semi break-in opera-tion is selected in stepe.
t Rotate [DIAL] to set the desired delay time. The delay time is selectable rom 0.2 to 13.0 (dots)
in 0.1 (dots) steps.
y Push M-CH/RITSET to exit the set mode and return tonormal operation.
e BK appears on the LCD.
When using a paddle, set KEY SPD in the quick
set mode to adjust the keying speed. (p. 72)
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH]
Appears
7.5 dots
Semi break-in operation
-
8/7/2019 IC-7200 Manual
61/104
56
6FUNCTIONS FOR TRANSMIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
D Full break-in operation
During ull break-in operation, the transceiver auto-matically switches to receive between keying dotsand dashes so that the operator can hear activity onthe channel when transmitting.
q Push MODE to select CW or CW-R mode. When CW mode is selected, push and hold MODE
or 1 sec. to toggle between CW and CW-R modes.
wSet the ull break-in unction ON in the set mode.
q Push and hold M-CH/RITSET or 1 sec. twice to enterthe set mode.
w Rotate [M-CH] to select BK-IN to set the CW
break-in operation.e Rotate [DIAL] to select FL.
FL : ull break-in
SE : semi break-in
OF : break-in OFF
r PushM-CH/RIT
SET to exit the set mode and return tonormal operation.
e F-BK appears on the LCD.
When using a paddle, set KEY SPD in the quickset mode to adjust the keying speed. (p. 72)
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH]
Appears
Full break-in operation
-
8/7/2019 IC-7200 Manual
62/104
57
6 FUNCTIONS FOR TRANSMIT
Speech compressor
The IC-7200 has a built-in, low distortion speech com-pressor circuit. This circuit increases your average talk
power in SSB mode and is especially useul or DX-ing or noisy conditions when the receiving station ishaving diculty copying your signal.
q Push MODE to select an SSB mode.
When SSB mode is selected, push and hold MODE
or 1 sec. to toggle between USB and LSB modes.
w Push COMP to turn the speech compressor unc-tion ON and OFF. appears when the speech compressor unc-
tion is ON.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL]
Appears
COMP 721
D Compression level setting
Microphone gain setting
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH]
q Push MODE to select an SSB mode.
When SSB mode is selected, push and hold MODE
or 1 sec. to toggle between USB and LSB modes.
w Push COMP to turn the speech compressor unc-tion OFF, i its ON. disappears.
e Push and holdANF
METER or 1 sec. several times toselect ALC meter. ALC appears.
r Adjust the MIC gain in the quick set mode.
q Push and hold M-CH/RITSET or 1 sec. to enter thequick set mode.
w Rotate [M-CH] to select MIC GAIN to set themicrophone gain.
eWhile transmitting, speak at a normal voice leveland rotate [DIAL] to adjust the microphone gainso that the ALC meter reads within the ALCzone, whether you speak sotly or loudly. Push and hold M-CL or 1 sec. to return to the de-
ault value.
r Push M-CH/RITSET to exit the quick set mode andreturn to normal operation.
Compression level setting
q Push and hold ANFMETER or 1 sec. several times toselect ALC meter. ALC appears.
w Push and hold COMP or 1 sec. to enter thespeech compression level set mode. The speech compressor unction is turned ON and
appears.
You can enter the speech compression level setmode beore selecting ALC meter in step q.
eWhile transmitting, speak at a normal voice leveland rotate [DIAL] to adjust the speech compres-sion level so that the ALC meter reads within theALC zone, whether you speak sotly or loudly. The speech compression level can be adjusted rom 0
to 10.
Push and hold M-CL or 1 sec. to return to the deault
value.
Level 5 (default)
ALC zone
rPush COMP to exit the speech compression levelset mode and return to normal operation.
t Push COMP to turn the speech compressor unc-tion OFF i necessary.
disappears.
NOTE: When the ALC meter peaks above the ALCzone, your transmitted voice may be distorted.
-
8/7/2019 IC-7200 Manual
63/104
58
6FUNCTIONS FOR TRANSMIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
Split requency operation
Split requency operation allows you to transmit andreceive in the same mode on two dierent requen-
cies. The split requency operation is perormed using2 requencies in VFO A and VFO B.
The transmit and receive requencies must be inthe same band
The ollowing is an example o setting 7.0620 MHz orreceiving and 7.0750 MHz or transmitting.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANF
METERNRNB
[DIAL] [M-CH]
F-INPENT
BAND
A/B 2=
3.5SPLIT 3
7Keypad
q Push A/B= to select VFO A.
w Set the requency to 7.0620 MHz and mode toLSB. (pgs. 25, 29)
e Push SPLIT to turn the split unction ON. appears on the LCD.
Appears
r Push and holdA/B= or 1 sec. to equalize the un-
displayed VFO B requency and operating modewith the displayed VFO A.
t Push A/B= to select the VFO B.
y Set the requency to 7.0750 MHz (LSB). (p. 25)
u Push A/B= to return to the VFO A.
i Now you can receive on 7.0620 MHz and transmiton 7.0750 MHz.
To swap the transmit and receive requencies,push A/B= to exchange the VFO A and VFO B.
CONVENIENT!
QUICK SPLIT FUNCTION (p. 59)
When you push and hold SPLIT or 1 sec., the splitunction is activated, and the undisplayed VFO is setthe same as the displayed VFO. (This operation issame as the stepse andr as at let.)
This shortens the time needed to start split re-quency operation.
Quick split unction is turned ON by deault but canbe turned OFF in the set mode (p. 76).
XFC FUNCTION (p. 76)When the XFC (transmit requency check) unction
is ON, the transmit requency can be changed (thisoperation is same as the stepst andy as at let.)
NOTE: When the XFC unction is ON, the RIT cal-culation unction (p. 44) is not available.
q Set the XFC (transmit requency check) unctionON in the set mode.
q Push and hold M-CH/RITSET or 1 sec. twice to enterthe set mode.
w Rotate [M-CH] to select XFC.e Rotate [DIAL] to select ON.
r Push M-CH/RITSET to exit the set mode and return tonormal operation.
wWhile pushing and holding RIT , the transmit re-quency is indicated. And rotate [DIAL] to set thetransmit requency.
-
8/7/2019 IC-7200 Manual
64/104
59
6 FUNCTIONS FOR TRANSMIT
D Quick split unction
When you nd a DX station, an important considera-tion is how to set the split requency.
When you push and hold SPLIT or 1 sec., the splitunction is activated, and the undisplayed VFO is setthe same as the displayed VFO.This shortens the time needed to start split re-quency operation.
Quick split operation is turned ON by deault but canbe turned OFF in the set mode (p. 76).
The ollowing is an example o setting 7.0620 MHzor receiving and 7.0750 MHz or transmitting.
q Select VFO A. Pushing A/B= toggles VFO A and VFO B.
w Set the requency to 7.0620 MHz and mode toLSB. (pgs. 25, 29)
e Push and hold SPLIT or 1 sec. to turn the splitunction ON and equalize the undisplayed VFO Brequency and operating mode with the displayedVFO A.
appears on the LCD.
r Set the XFC (transmit requency check) unctionON in the set mode. (pgs. 58, 76)
The deault setting is OFF.
tWhile pushing and holding RIT , rotate [DIAL] toset the transmit requency to 7.0750 MHz.
y Now you can receive on 7.0620 MHz and transmiton 7.0750 MHz.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[DIAL] [M-CH]
A/B 2=
3.5SPLIT 3
7
Appears
D Split lock unction
Accidentally releasing RIT while rotating [DIAL]changes the receive requency. To prevent this, useboth the split lock and dial lock unctions to changethe transmit requency only. The split lock unc-
tion cancels the dial lock unction while pushing andholding RIT during split requency operation.
The dial locks eectiveness during split requencyoperation can be selected in the set mode or bothreceive and transmit requencies; or only the receiverequency. (p. 76)
When the split lock unction is ON, the transmit re-quency cannot be adjusted by rotating [DIAL] whiletransmitting even i the lock unction is not activated.
q Set the split lock unction ON in the set mode.
q Push and hold M-CH/RITSET or 1 sec. twice to enterthe set mode.
w Rotate [M-CH] to select SPLIT LK.
e Rotate [DIAL] to select ON.r Push M-CH/RITSET to exit the set mode and return to
normal operation.
w During split operation, push and hold SPCH or1 sec. to turn the dial lock unction ON.
appears on the LCD.
eWhile pushing and holding RIT *, the transmitrequency and mode are indicated. And Rotate[DIAL] to set the transmit requency.
*XFC unction is should be turned ON in advance. (p. 76)
-
8/7/2019 IC-7200 Manual
65/104
60
6FUNCTIONS FOR TRANSMIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
Measuring SWR
The IC-7200 has a built-in circuit or measuring an-tenna SWRno external equipment is necessary.
q Push MODE to select CW or RTTY mode.
w Conrm that the output power is over 30 W.
e Push and hold ANFMETER or 1 sec. several times toselect the SWR meter.
r Push [PTT] to transmit; then read the actual SWRrom the meter. 1.5 well-matched antenna
> 1.5 may indicate an antenna out o its well-matched
requency range. I much larger than 2.0, check an-
tenna and cable connections, etc.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETER
NRNB
Appears The best match is in this range.
-
8/7/2019 IC-7200 Manual
66/104
7
61
MEMORY OPERATION
Memory channels
The transceiver has 201 memory channels including2 scan edge channels.
Memory mode is very useul or quickly changing tooten-used requencies.
All 201 memory channels are tuneable which meansthe programmed requency can be tuned temporarily
with [DIAL], etc., in memory mode.
MEMORY
CHANNEL
MEMORY
CHANNEL
NUMBER
CAPABILITYCOPY
TO VFO
OVER-
WRITINGCLEAR
Regular memory
channels1199
Independent transmit and receive requencies
and mode in each memory channel.Yes Yes Yes
Scan edge
memory channelsP1, P2
One requency and one mode in each memory
channel as scan edges or programmed scan.Yes Yes No
Memory channel selection
q Push V/M to select memory mode.
appears.
w Rotate [M-CH] to select the desired memorychannel. I the RIT control indicator lights orange, push
M-CH/RITSET to set the [M-CH] control to memory chan-
nel control. (See below or details)
All memory channels including blank channels can be
selected.
[UP]/[DN] on the microphone also selects the mem-ory channels. (The only programmed memory chan-
nels are selectable.)
Channel decreases
Channel increases
RIT control indicatorgoes out
About the [M-CH] control:When the RIT control indicator lights orange, the
memory channels cannot be selected with rotat-ing the [M-CH] control because the [M-CH] con-trol acts as the RIT control. So, push M-CH/RITSET toset the [M-CH] control to memory channel control(RIT control indicator goes out).
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[M-CH]
RIT control
indicator
[EXAMPLE]: Selecting memory channel 17.
Push
Appears
Rotate [M-CH]
VFO mode
Memory mode
Channel 17 is selected.
-
8/7/2019 IC-7200 Manual
67/104
-
8/7/2019 IC-7200 Manual
68/104
63
Frequency copying
The requency and operating mode in a memorychannel can be copied to the VFO.
D Copying in memory mode
This is useul or copying a memory channels con-tents (requency and operating mode) to a VFO whileoperating in memory mode.This is useul when searching or signals around amemory channel requency.
NOTE: While operating in VFO mode, pushing andholding V/M or 1 sec. also copy the selectedmemory channels contents (requency and oper-
ating mode) to a VFO.
When you have changed the requency or operat-ing mode in the selected memory channel: Displayed requency and mode are copied. Programmed requency and mode in the mem-
ory channel are not copied, and they remain inthe memory channel.
q Push V/M to select memory mode.w Rotate [M-CH] to select the desired memory
channel to be copied. I the RIT control indicator lights orange, push
M-CH/RITSET . (p. 61)
Set the requency or operating mode i required. appears i the selected memory channel is a
blank channel (and does not have contents). In this
case copying is not possible.
Channel decreases
Channel increases
RIT control indicator
goes out
e Push and hold V/M
or 1 sec. to copy the re-quency and operating mode. 3 beeps are emitted when the copying is successul.
Displayed requency and operating mode are copied.
r To return to VFO mode, push V/M . Copied requency and operating mode appear in the
display.
You can return to VFO mode beore copyingthe requency and operating mode in step e.
[EXAMPLE]: Copying contents of memory 16.Operating frequency
Contents of memory 16
: 14.020 MHz/CW
: 14.018 MHz/CW
V/M 11.8Push and hold for 1 sec.,
then push .V/M 11.8
Rotate [M-CH]
7 MEMORY OPERATION
-
8/7/2019 IC-7200 Manual
69/104
-
8/7/2019 IC-7200 Manual
70/104
8
65
SCAN OPERATION
ChannelsFor programmed scan:Program scan edge requencies into scan edge mem-ory channels P1 and P2. (p. 66)
For memory scan:Program two or more memory channels except scanedge memory channels.
Scan resume ON/OFF
You can select the scan to resume or cancel whendetecting a signal in the set mode.Scan resume ON/OFF must be set beore operating ascan. See p. 78 or ON/OFF setting and scan resumecondition details.
Scan speedScan speed can be selected rom 2 levels, high orlow, in the set mode. See p. 78 or details.
Squelch condition
Scan starts with squelch openFor programmed scan:
When tuning step is 1 kHz or less:The scan continues until it is stopped manually withpushing SCAN , and does not pause* even i signalsare detected.* The scan is paused when the squelch is closed and
then opened (scan resumes ater 10 sec. has passed
when the scan resume is ON; scan is cancelled when
OFF).
When tuning step is more than 5 kHz:The scan pauses on each step when the scanresume is ON; not applicable when OFF.
For memory scan:Scan pauses on each channel when the scan resumeis ON; not applicable when OFF.
Scan starts with squelch closedScan stops when a signal is detected.I you set scan resume ON in the set mode, the scan
pauses or 10 sec. when detecting a signal, thenresumes. When a signal disappears while scan ispaused, scan resumes 2 sec. later.
NOTE: I the [RF/SQL] control unction is set asAUTO, the squelch is always open in SSB, CWand RTTY modes. (pgs. 4, 30, 75)
Scan types
Preparation
PROGRAMMED SCAN
Repeatedly scans between two scan edge frequencies
(scan edge memory channels P1 and P2).
This scan operates in VFO mode.
Scan
Scan edge P1 or P2 Scan edge P2 or P1
Jump
This scan operates in memory mode.
MEMORY SCAN
Repeatedly all programmed memory channels thatare not blank.
Mch 1 Mch 5
Mch 2 Mch 3 Mch 4
Mch 6Mch 7Mch 199
BLANK
-
8/7/2019 IC-7200 Manual
71/104
66
8SCAN OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2021
Programmed scan operation (VFO mode)
Programmed scan searches or signals betweenscan edge memory channels P1 and P2.The deault requencies or these memories are0.500000 MHz and 29.99999 MHz, respectively.See p. 62 or scan edges programming.
q Push V/M to select VFO mode.
w Push MODE to select the desired operatingmode.
The operating mode can be changed while scanning.
e Push TS to select a tuning step.
The tuning step cannot be changed while scanning.
(The programmed tuning unction can be turned ON
or OFF while scanning.)
r Set the [RF/SQL] control open or closed.
See the let page or squelch condition.
t Push SCAN to start the scan.
appears while scanning.
yWhen the scan detects a signal, the scan turnsOFF, pauses or ignores it depen ding on theresume setting and the squelch condition.
u To cancel the scan, push SCAN .
NOTE: I the same requencies are programmedinto both scan edge memory channels P1 and P2,programmed scan does not start.
MODE
TUNER
TS
FILTER
SPCH
V/M A/B SPLIT
M-CL
SCAN
SET
ATTP.AMP
COMP VOX
MNFRIT
1 2 3
4 5 6
7 8
050
28
181410
21 24
= 73.51.8
F-INP
M-CH/RIT
ENT
BANDGENE
9
.
AGCMW
ANFMETERNRNB
[RF/SQL]
Appears
Memory scan operation (Memory mode)
Memory scan searches through memory channel1 to 199 or signals. Blank (unprogrammed) memorychannels are skipped.
q Push V/M to select memory mode.
w Close the squelch with the [RF/SQL] control.
e Push SCAN to start the scan.
appears while scanning.
rWhen the scan detects a signal, the scan stops orpauses