I-FLEX ‘HIGH TEMPERATURE’ FLANGE INSULATING SET · 2016. 9. 28. · Tel. +44 (0)1274 851273...
Transcript of I-FLEX ‘HIGH TEMPERATURE’ FLANGE INSULATING SET · 2016. 9. 28. · Tel. +44 (0)1274 851273...
-
Tel. +44 (0)1274 851273 Fax. +44 (0)1274 300303 www.flexitallic.eu Email. [email protected]
The insulating gasket is constructed froma serrated metal core utilising Flexitallic’sunique ‘Shallow P’ profile. The metal core is faced with Thermiculite® 725; a highperformance, fire safe sealing materialincorporating Flexitallic’s proprietaryvermiculite based sealing material. Correct gasket location is ensured by the inclusion of a Thermiculite® 725 spacerring positioned around the periphery of the serrated metal core.
Colour: Brown
Service:Flexitallic I-Flex high temperature flangeinsulation sets are specifically designed to effect a seal and maintain electricalisolation across a wide range of seatingstresses and flange classes in elevatedtemperature service. They can be utilisedin load compromised connections; such asdamaged and/or lined flanges and alsoheavily bolted connections where significantgasket stresses may be generated. In addition the relatively high compressioncharacteristics of the facing materialsensure both seal and isolation performancecan be realised over a wide range of flangesurface finishes. The use of Thermiculite®725 as the sealing material pushes theperformance of the ‘high temperature’insulation set beyond the capability oftraditional insulation sets based on phenolicresin or glass/epoxy sealing technology.
This Data Sheet refers to the material assupplied. The information contained herein is given in good faith, but no liability will beaccepted by the Company in relation to same.
We reserve the right to change the detailsgiven on this Data Sheet as additionalinformation is acquired. Customers requiringthe latest version of this Data Sheet shouldcontact our Applications EngineeringDepartment.
The information given and, in particular, anyparameters, should be used for guidancepurposes only. The Company does not giveany warranty that the product will be suitablefor the use intended by the customer.
PDS485 – 01/15 Rev3
PRODUCT DATASHEET
The Flexitallic I-Flex ‘High Temperature’ FlangeInsulating Set is comprisedof an insulating gasket,insulating sleeves,insulating washers andmetal backing washers.
I-FLEX ‘HIGHTEMPERATURE’ FLANGEINSULATING SET
Operational pressure range: Full vacuum to ASME B16.5 /16.47 2500 class
Operational temperature range: -200 to 380oC
Fire safe compliance:API 6FB (Third edition)
Thermiculite® 725 facing material issuitable for sealing across a wide rangeof chemicals (pH 0-14) and sweet andsour gaseous and liquid hydrocarbons.
Gasket and washer metallurgy isselected to suit the particularapplication. Unless specified allmaterials are NACE (MRO175)compliant.
The insulating gasket and washers havebeen designed and developed for use instandard pipeline flanges where bothcathodic protection and high integritysealing is required at elevated servicetemperatures. For non-standard boltedconnections please consult the FlexitallicApplications Engineering Department.
-
Tel. +44 (0)1274 851273 Fax. +44 (0)1274 300303 www.flexitallic.eu Email. [email protected]
Each I-Flex insulating set comprises of the following components:
High Temperature Insulating Gasket 1 per flangeHigh Temperature Insulating Sleeves 1 per flange boltHigh Temperature Insulating Washers 2 per flange boltMetallic Backing Washers 2 per flange bolt
Please contact the Flexitallic Applications Engineering Team when specificoperating parameters requires confirmation of appropriate materials.
PDS485 – 01/15 Rev3
PRODUCT DATASHEET
Typical Physical Properties:
Insulating Gasket & Washers:
Core Thickness 2.5mm to 4mm
Facing Thickness 0.75mm (x2)
ASME Gasket Factor (m) 4.00
ASME Minimum Seating Stress (Y) 3625 psi
Thermiculite® 725 - Dielectric Strength (ASTM D149a) 6.1 kV/mm
Sleeve Material Properties:
Insulating Sleeves / Tubes – Thermal / Dielectric Properties
Attamica H – Maximum Temperature +500oC
Attamica H - Dielectric Strength (ASTM D149a) 20.0 kV/mm
Metallic Backing Washers:Stainless Steel Washers 3mm thk
Other washer material can be provided to suit the application.
General Assembly: