Hilti HT Metal Frame Anchor

7/23/2019 Hilti HT Metal Frame Anchor

http://slidepdf.com/reader/full/hilti-ht-metal-frame-anchor 1/7

HT Metal frame anchor

Hilti (Gt. Britain) Limited,

1 Trafford Wharf Road, Trafford Park, Manchester M17 1BY

Telephone:

0800 886 100

HILTI HT Metal f rame anchor

The enclosed pages are taken from theHilti Fastening Technology Manual

Edition September 2012

For further details including details of product European Technical Approvals,Guidance on product selection and detailed design assistance please contact

Hilti (Gt Britain) Ltd Technical Advisory Service.

Hilti (Gt Britain) LtdTECHNICAL ADVISORY

SERVICE

Telephone 0161 886 1144

Email [email protected]

Quality Management Approvals

ISO 9001: 2008 Quality Management SystemCertified by: The Swiss Association for Quality andManagement Systems.

Registration No: 12455 Valid until 30th June 2013Scope No: 18, Machinery and Equipment.Note: Under our accreditation with SQS the scope of accreditation is notcontained within an appendix but is stated as Scope 18 on the SQSCertificate. Scope No. 18 is Machinery and Equipment.”






Telephone:

0800 886 100

Important notice

1. Construction materials and conditions vary on different sites. If it issuspected that the base material has insufficient strength to achieve asuitable fastening, contact the Hilti Technical Advisory Service.2. The information and recommendations given herein are based on theprinciples, formulae and safety factors set out in the Hilti technicalinstructions, the operating manuals, the setting instructions, the installationmanuals and other data sheets that are believed to be correct at the time ofwriting. The data and values are based on the respective average valuesobtained from tests under laboratory or other controlled conditions. It is theusers responsibility to use the data given in the light of conditions on site andtaking into account the intended use of the products concerned. The userhas to check the listed prerequisites and criteria conform with the conditionsactually existing on the job-site. Whilst Hilti can give general guidance andadvice, the nature of Hilti products means that the ultimate responsibility forselecting the right product for a particular application must lie with thecustomer.3. All products must be used, handled and applied strictly in accordance withall current instructions for use published by Hilti, i.e. technical instructions,operating manuals, setting instructions, installation manuals and others.4. All products are supplied and advice is given subject to the Hilti terms ofbusiness.5. Hilti´s policy is one of continuous development. We therefore reserve theright to alter specifications, etc. without notice.6. The given mean ultimate loads and characteristic data in the AnchorFastening Technology Manual reflect actual test results and are thus validonly for the indicated test conditions.Due to variations in local base materials, on-site testing is required todetermine performance at any specific site.7. Hilti is not obligated for direct, indirect, incidental or consequential

damages, losses or expenses in connection with, or by reason of, the use of,or inability to use the products for any purpose. Implied warranties ofmerchantability or fitness for a particular purpose are specifically excluded.

Hilti CorporationFL-9494 SchaanPrincipality of Liechtensteinwww.hilti.com






Telephone:

0800 886 100

Visit our web site at www.Hilti.co.uk/technical to access our

comprehensive technical support services

Design andSpecification

Profis AnchorSoftware

Technical Library

Access ourcomprehensive

engineering support ,including the AnchorDesign and FirestopDesign Centres

Profis Anchor 2.1 is thelatest Hilti software,

designed to assistplanners and specifiersto select the requiredanchors for yourapplications.

Download the latesttechnical

documents (approvals, testreports, etc.) andsoftware (PROFIS Anchor).

Hilti (Gt. Britain) Ltd is amember of theConstruction Fixings Association.




09 / 2012312

Anchor version Benefits

HT - fastening door and windowframes

- no risk of distortion or forces ofconstraint

- expansion cone can not be lost

Approvals / certificates

Description Authority / Laboratory No. / date of issue

Fire test report IBMB, Braunschweig UB 3016/1114-CM / 2006-03-13

Assessment report (fire) warringtonfire WF 166402 / 2007-10-26

Basic loading data (for a single anchor)

All data in this section applies to- Correct setting (See setting instruction)- No edge distance and spacing influence- Base material as specified in the table- Non-cracked concrete: f cc 20 N/mm

2

- Minimum base material thickness

Characteristic resistance

HT 8 HT10

Concrete, f cc = 30 N/mm²NRk [kN] 4,2 5,0

VRk [kN] 6,6 7,0

Aerated Concrete PP2a)

NRk [kN] - 0,3

VRk [kN] - 0,5

Solid brick Mz 12NRk [kN] 1,8 2,6

VRk [kN] - 5,0

Sand-lime solid brick, KS 12NRk [kN] 1,8 2,6

VRk [kN] - 5,0

Sand-lime hollow brick, KSLNRk [kN] - 1,5

VRk [kN] - 0,5

a) Rotary drilling only




09 / 2012 313

Recommended loads

HT 8 HT10

Concrete, f cc = 30 N/mm²

Nrec [kN] 1,4 1,7

Vrec [kN] 0,5 0,5

Aerated Concrete PP2a)

Nrec [kN] - 0,1

Vrec [kN] - 0,15

Solid brick Mz 12Nrec [kN] 0,6 0,8

Vrec [kN] - 0,5

Sand-lime solid brick, KS 12Nrec [kN] 0,6 0,8

Vrec [kN] - 0,5

Sand-lime hollow brick, KSLNrec [kN] - 0,5

Vrec [kN] - 0,15

a) Rotary drilling only

Materials

Material quality

Part Material

Bolt steel strength 4.8, zinc plated to 5 µm

Sleeve steel 02 DIN 17162, sendzimir zinc plated to 20 µm

Setting

installation equipment

Anchor size

Rotary hammer TE1 – TE16

Other tools hammer, screwdriver

Setting instruction

Drill hole with drill bit. Install anchor. Drive screw into anchor.

For detailed information on installation see instruction for use given with the package of the product.




09 / 2012314

Setting details: anchor length L and anchorage depth hnom

Setting details HTHT 8 8x72 8x92 8x112

Nominal diameter of drill bit do [mm] 8 8 8

Depth of drill hole h1 [mm] 50 50 50

Anchorage depth hnom [mm] 30 30 30

Anchor length L [mm] 72 92 112

Torque moment Tinst [Nm] 4 4 4

Minimum base material thickness hmin [mm] 100 100 100

Drill bit TE-CX-8/17

HT 8 8x132 8x152 8x182





Torque moment Tinst [Nm] 4 4 4


Drill bit TE-CX-8/27

HT 10 10x72 10x92 10x112





Torque moment Tinsta)

[Nm] 8/4 8/4 8/4


Drill bit TE-C-10/17

a) First value: solid base material, second value: hollow base material

min. 50mm




09 / 2012 315

HT 10 10x132 10x152 10x182 10x202

Nominal diameter of drill bit do [mm] 10 10 10 10

Depth of drill hole h1 [mm] 50 50 50 50

Anchorage depth h0 [mm] 30 30 30 30

Anchor length L [mm] 132 152 182 202

Torque moment Tinsta)

[Nm] 8/4 8/4 8/4 8/4

Minimum base material thickness hmin [mm] 100 100 100 100

Drill bit TE-C-10/22

TE-C-10/27TE-C-10/37

a) First value: solid base material, second value: hollow base material

Hilti HT Metal Frame Anchor

Documents

Transcript of Hilti HT Metal Frame Anchor