Hilti HIT-RE500-SD Injection Adhesive with HI6 5 1 · Hilti HIT-RE500-SD Injection Adhesive with...

Submission folder

Customer Hotline Customer Hotline Hong Kong 8228 8118Macau (Toll free) 00800- 8228 8118

Hilti HIT-RE500-SD Injection Adhesive with HIS-(R)N

Sample Submission and 2 - 5 Approval Form

Product Information 6 - 12 Technical Information 13 - 18

VOC Content Test Certificate (LEED) 19

Country of Origin 20 - 21

Material Safety Data Sheet 22 - 28

Government Letter 29 - 30 Job Reference 31 - 32

July 2014

of 2

SAMPLE SUBMISSION AND APPROVAL FORM

Contract Title: ________________________________ Ref. No.: ________________________

________________________________ Date: ________________________

Ref. No. of Previous Submission:

________________________

Contract No: ________________________________ (1) ________________________

File Reference: ________________________________ (2) ________________________

DETAILS OF SUBMISSION

To: Contract Manager’s Representative Attention: ________________________

From: ________________________________

The enclosed sample and catalogue* / certificate of origin* / technical data* / test report* / job reference* as described below have been checked for compliance with the Specifications and Drawings, and are submitted for approval.

1. General Information a. Material Description HIT – RE500-SD Injection Adhesive __________________________________________________________ __________________________________________________________ b. Location: __________________________________________________________ __________________________________________________________ __________________________________________________________ c. Specification Ref. Page: __________________________ Item: _______________________ __________________________ _______________________ __________________________ _______________________ d. Drawing Ref. No. __________________________________________________________ __________________________________________________________ __________________________________________________________ e. B.Q. Ref.No.: __________________________________________________________ __________________________________________________________ __________________________________________________________ f. Anticipated date of approval: __________________________________________________________

2. Technical Information The submitted sample has been checked against the specification and drawings as listed below:-

Specification Requirements Submitted Sample (State details against each item)

a. Brand Not specified Hilti b. Country of Origin Not specified Germany c. Manufacturer’s Name & Address Not specified Hilti Corporation, FL-9494 Principality of Liechtenstein.

d. Factory’s Name & Address(es) Not specified Hilti Gmbh Ind. Ges. F. Befestigungstechnik Hiltistrasse 6, D-86916 Kaufering, Germany. e. Supplier (with Applicator, if any) Not specified Hilti (Hong Kong) Ltd

July 2014

of 2

f. Appearance Not specified According to the sample submitted

g. Color + Not specified Red

h. Specification Not specified Attached

i. Manufacturer’s Catalogue Not specified Attached

j. Test Report (Original/Certificated True Copy) Not specified Attached

k. Previous Job Reference Not specified Attached

l. Supplementary Information Not specified NIL

For and on behalf of the Contractor

____________________________ (Quality Control Manager)

CONTRACT MANAGER’S COMMENTS To:From: Contract Manager’s Representative: ________________________________

On the basis of the sample and information given, the above sample submitted is:

(1) * Approved. (2) * Not approved because ____________________________________________________ _______________________________________________________________________ _______________________________________________________________________ Remarks: _______________________________________________________________________ _______________________________________________________________________ _______________________________________________________________________

Approval does not alter the requirements of the Contract Contract Manager’s Representative: ____________________________

_____________________________ Date:

cc. _______________________________________ _______________________________________ _______________________________________ _______________________________________

(* Delete if appropriate) (+ For glass or vitreous mosaic tiles, the contractor is required to confirm the colour range(s) of the submitted sample, i.e. a) light and or medium; or b) dark)

July 2014

of 2

SAMPLE SUBMISSION AND APPROVAL FORM

Contract Title: ________________________________ Ref. No.: ________________________

________________________________ Date: ________________________

Ref. No. of Previous Submission:

________________________

Contract No: ________________________________ (1) ________________________

File Reference: ________________________________ (2) ________________________

DETAILS OF SUBMISSION

To: Contract Manager’s Representative Attention: ________________________

From: ________________________________

The enclosed sample and catalogue* / certificate of origin* / technical data* / test report* / job reference* as described below have been checked for compliance with the Specifications and Drawings, and are submitted for approval.

1. General Information a. Material Description HAS-E/ER/EF Anchor Rod or HIS-N/RN (M8-M24) Anchor Sleeve __________________________________________________________ __________________________________________________________ b. Location: __________________________________________________________ __________________________________________________________ __________________________________________________________ c. Specification Ref. Page: __________________________ Item: _______________________ __________________________ _______________________ __________________________ _______________________ d. Drawing Ref. No. __________________________________________________________ __________________________________________________________ __________________________________________________________ e. B.Q. Ref.No.: __________________________________________________________ __________________________________________________________ __________________________________________________________ f. Anticipated date of approval: __________________________________________________________

2. Technical Information The submitted sample has been checked against the specification and drawings as listed below:-

Specification Requirements Submitted Sample (State details against each item)

a. Brand Not specified Hilti b. Country of Origin Not specified Republic of China c. Manufacturer’s Name & Address Not specified Hilti Corporation, FL-9494 Principality of Liechtenstein.

d. Factory’s Name & Address(es)

Not specified Hilti (China Zhangjiang) Co. Ltd., Yongping Road South, Zhangjiang Development Zone, 524022 Zhangjiang, Guangdong Province, China.

e. Supplier (with Applicator, if any)

July 2014

of 2

Not specified Hilti (Hong Kong) Ltd

f. Appearance Not specified According to the sample submitted

g. Color + Not specified Nil

h. Specification Not specified Attached

i. Manufacturer’s Catalogue Not specified Attached

j. Test Report (Original/Certificated True Copy) Not specified Attached

k. Previous Job Reference Not specified Attached

l. Supplementary Information Not specified NIL

For and on behalf of the Contractor

____________________________ (Quality Control Manager)

CONTRACT MANAGER’S COMMENTS To:From: Contract Manager’s Representative: ________________________________

On the basis of the sample and information given, the above sample submitted is:

(1) * Approved. (2) * Not approved because ____________________________________________________ _______________________________________________________________________ _______________________________________________________________________ Remarks: _______________________________________________________________________ _______________________________________________________________________ _______________________________________________________________________

Approval does not alter the requirements of the Contract Contract Manager’s Representative: ____________________________

_____________________________ Date:

cc. _______________________________________ _______________________________________ _______________________________________

(* Delete if appropriate) (+ For glass or vitreous mosaic tiles, the contractor is required to confirm the colour range(s) of the submitted sample, i.e. a) light and or medium; or b) dark)

July 2014

180

Anchor Systems

Customer Hotline: Hong Kong 8228 8118 Macau 00800 8228 8118

8

Ordering designation Package contentsSales pack quantity

Item number

HIT-RE 500-SD/330/1 1x Foil pack, 1x Mixer, 1x Mixer extension 1 pc 3870921)

HIT-RE 500-SD/500/1 1x Foil pack, 1x Mixer, 1x Mixer extension 1 pc 3870931) This is a non-stock item. For detailed lead time information please contact your Hilti representative.

Injectable mortar HIT-RE 500-SD

Applications■ Structural connections with post-installed rebar (e.g. extension/

connection to walls, slabs, stairs, columns, foundations, etc.)■ Anchoring structural steel connections (e.g. steel columns,

beams, etc.)■ Special applications requiring electrical isolation such as fasten-

ing emergency escape handrails in tunnels■ Structural renovation of buildings, bridges and other civil struc-

tures, retrofitting and re-strengthening of concrete members possible

■ Substitution of misplaced / missing rebars or couplers■ Suitable for underwater applications in hammer-drilled holes

(ICC-ESR)

Advantages■ Suitable for use in cracked and uncracked concrete with all

anchoring elements■ Seismic approval for use in seismic applications■ Suitable for anchoring in diamond-cored holes (ICC-ESR)■ High performance and technical superiority as per international

approvals■ No expansion forces in concrete allow secure fastenings even

close to edges and/or with close spacing■ Virtually odourless hence convenient to work with

Base materials ◾ Concrete (cracked) ◾ Concrete (uncracked)

Technical dataMaterial composition Epoxy adhesive

Tested/approved for diamond drilling Yes

Seismic Yes

In-service temperature – range -40 - 70 °C

IBC compliance IBC 2003,IBC 2006,IBC 2009

Additional product information Always wear eye protection and gloves while handling

These are abbreviated instructions which may vary according to the application. Always observe/follow the instructions accompanying the product or refer to www.hilti.com/techlib.

July 2014

189

Anchor Systems

Hilti online: www.hilti.com.hk

Ordering designation Anchor size Drill bit diameter Base plate clearance holeSales pack quantity

Item number

HIS-RN M8X90 A4 M8 14 mm 9 mm 10 pc 2580241)

HIS-RN M10X110 A4 M10 18 mm 12 mm 10 pc 258025

HIS-RN M12X125 A4 M12 22 mm 14 mm 5 pc 258026



1) This is a non-stock item. For detailed lead time information please contact your Hilti representative.

Internally threaded sleeve (A4 stainless steel) HIS-RN

ApprovalsETA (ETAG 001-05, Option 7)Approvals and test reports may apply to selected products only. Please refer to the documents for details.

Technical dataHead configuration Inner thread

Material composition Steel, A4 (SS316)

Material, corrosion Steel, stainless

Anchor type Internally threaded

Approvals / test reports ETA

Fire Yes

Base materials ◾ Concrete (cracked) ◾ Concrete (uncracked)

Ordering designation Anchor size Drill bit diameter Base plate clearance holeSales pack quantity

Item number

HIS-N M8X90 M8 14 mm 9 mm 10 pc 2580151)

HIS-N M10X110 M10 18 mm 12 mm 10 pc 2580161)

HIS-N M12X125 M12 22 mm 14 mm 5 pc 258017

HIS-N M16X170 M16 28 mm 18 mm 5 pc 258018

HIS-N M20X205 M20 32 mm 22 mm 5 pc 2580191)


Internally threaded sleeve (5.8 carbon steel) HIS-N

ApprovalsETA (ETAG 001-05, Option 7)Approvals and test reports may apply to selected products only. Please refer to the documents for details.

Technical dataHead configuration Inner thread

Material composition Steel, 5.8 grade, zinc-plated (min. 5 µm)

Material, corrosion Steel, zinc-plated

Anchor type Internally threaded

Approvals / test reports ETA

Fire Yes

Base materials ◾ Concrete (uncracked)

July 2014

183

Anchor Systems


Ordering designation WeightSales pack quantity

Item number

HDE 500 CB DISPENSER KIT 1 pc 34990781)

HDE 500-A22 box 2.2 kg 1 pc 2005630

HDE 500-A22 CR/CB cas 2.2 kg 1 pc 2005637

HDE 500-A22 empty 2.4 kg 1 pc 4347241) This is a non-stock item. For detailed lead time information please contact your Hilti representative.

Dispenser HDE 500-A22

Applications■ Injection of Hilti HIT adhesive mortar for fastening anchor rods

and rebars in concrete and masonry ■ No need for external power source supply■ Serial fastenings and/or injection in deep holes

Advantages■ Dose adjustment knob for accurate and controlled dispensing■ Fast, easy foil pack loading■ High battery capacity (up to 100x500ml foil packs)

Technical dataDispenser, setting tool, accessory, tester type

Dispensers

Ordering designation WeightSales pack quantity

Item number

HDM 330 CB DISPENSER KIT 1 pc 34990821)

HDM 330 CB CARDBOARD BOX 1 pc 34991031)

HDM 500 CB DISPENSER KIT (2060870 W/ACC) 1 pc 3499081

HDM 330 cas 1 pc 2060429

HDM 500 cas 1 pc 2060870

HDM 330 box 1.5 kg 1 pc 2005640

HDM 500 box 1.8 kg 1 pc 20056411) This is a non-stock item. For detailed lead time information please contact your Hilti representative.

Dispenser HDM

Applications■ Injection of Hilti HIT adhesive mortar for fastening anchor rods

and rebars in concrete and masonry

Advantages■ Fast, easy foil pack loading


Dispensers, n/a

July 2014

104

Drilling and Demolition

4

Ordering designation Diameter Working length LengthSales pack quantity

Item number

TE-YD 16/59 16 mm 400 mm 590 mm 1 pc 2018956

TE-YD 18/59 18 mm 400 mm 590 mm 1 pc 2018957

TE-YD 20/59 20 mm 400 mm 590 mm 1 pc 2018959

TE-YD 22/59 22 mm 400 mm 590 mm 1 pc 2018960

TE-YD 25/59 25 mm 400 mm 590 mm 1 pc 2018962

TE-YD 28/59 28 mm 400 mm 590 mm 1 pc 2018964

TE-YD 32/59 32 mm 400 mm 590 mm 1 pc 2018966

Hammer drill bit TE-YD

Applications■ Drilling holes for anchoring structural steel connections (e.g.

steel columns, beams)

Advantages■ Drilling and hole cleaning in one step


Ordering designation Diameter Working length LengthSales pack quantity

Item number

TE-CD 12/33 12 mm 200 mm 330 mm 1 pc 2018940

TE-CD 14/37 14 mm 240 mm 360 mm 1 pc 2018942

TE-CD 16/37 16 mm 240 mm 360 mm 1 pc 2018945

TE-CD 18/37 18 mm 240 mm 360 mm 1 pc 2018946

Hammer drill bit TE-CD

Applications■ Drilling holes for structural connections with post-installed

rebars

Advantages■ Drilling and hole cleaning in one step

July 2014

TSANTER

Typewritten Text

TSANTER

Typewritten Text

TSANTER

Typewritten Text

TSANTER

Typewritten Text

TSANTER

Typewritten Text

TSANTER

Typewritten Text

TSANTER

Typewritten Text

TSANTER

Typewritten Text

TSANTER

Typewritten Text

243

Anchor Systems


Ordering designationSales pack quantity

Item number

Blow-out pump 1 pc 60579

Extension tube HIT-VL 16/0.7 10 pc 336646

Accessories for blowing out drilled holes Hilti HIT

Applications■ For fast and efficient removal of dust and debris from drilled

holes of varying diameters and depths to allow correct installa-tion of anchors and rebar


Cleaning accessories

Ordering designation Drill hole diameterSales pack quantity

Item number

Air nozzle HIT-DL 20 20 mm 1 pc 3717191)




Hilti HIT Profi accessories Air nozzle

Applications■ Clearing dust and debris from drilled holes under various condi-

tions including where adhesive anchors are set at great depth

Advantages■ Fast, effective cleaning of drilled holes




Item number

Brush extension HIT-RBH 1 pc 2291381)

Brush extension HIT-RBV 1 pc 2387271)

Holder TE-Y 1 pc 2634391)

Brush extension HIT-RBS 10/0.7 1 pc 3366451)

Round brush 13 HG 12 mm 1 pc 229133


Round brush 18 GA 18 mm 1 pc 2291361)

Round steel brush HIT-RB 20 20 mm 1 pc 3365521)










Accessories for using brushes to clean holes Hilti HIT

Applications■ For the proper brushing of drilled holes of varying diameters and

embedment depths



July 2014

244

Anchor Systems


8


Item number

Hose HIT-VL 11/1.0 10 pc 20425331)

Coupler VL-K 10 pc 3350211)

Piston plug HIT-SZ 20 20 mm 10 pc 20393121)






Profi accessories for mortar injection Hilti HIT

Applications■ For injection of Hilti HIT adhesive mortars in a variety of situa-

tions including deep holes, overhead holes and in underwater applications

Advantages■ Injection pistons and flexible extension hoses help ensure con-

sistent injection of the adhesive into the hole without formation of air voids


Mixing nozzles and injection accessories


Item number

Drip guard HIT-OHC1 10 pc 387551

Drip guard HIT-OHC2 10 pc 387552

Wedge HIT-OHW 100 pc 387550

Overhead cup




Item number

Safety glasses 1 pc 52051)


HIT Profi accessories (Glasses & empty cases)


Other accessories

July 2014

245

Anchor Systems



Item number

Mixer HIT-RE-M 1 pc 337111

Mixer HIT-M1 assy 100 pc 68156

Mixers and extensions Hilti HIT



Ordering designation Package contentsSales pack quantity

Item number

VC 40-U 110V 1x Univ. vacuum cleaner VC 40-U 110 V 1 pc 2183451)

VC 40-U 230V 1x Univ. vacuum cleaner VC 40-U 230 V 1 pc 2123001) This is a non-stock item. For detailed lead time information please contact your Hilti representative.

Universal vacuum cleaner VC 40-UM

Technical dataContainer capacity 36 l

Dust capacity 40 kg

Water capacity 25 l

A-weighted emission sound pressure level acc. to EN 60745

71 dB (A)

Hose diameter 36 mm

Hose length 5000 mm

Weight according to EPTA Procedure 01/2003

14.7 kg

Dimensions (LxWxH) 505 x 380 x 610 mm

Applications■ Removing dust from drilling, slitting, grinding, cutting and dry

coring■ Removing slurry from wet coring and cleaning

Advantages■ Hilti AirBoost filter technology for consistently high suction

performance■ Very good handling thanks to compact design■ Full exploitation of tank capacity due to placement of filter and

hose connection in the upper part of the machine■ Robust housing to withstand the harshest jobsite conditions■ New tank concept for easy and virtually dust-free dust removal■ Maximum total load of dust: up to 40 kg

July 2014

July 2014

88 Empire Drive • St. Paul, Minnesota • 55103 (651) 642-1150 • fax (651) 642-1239

VOC Content Test Certificate Friday June 19, 2009

Supplier: Hilti Entwicklungsgesellschaft mbH BU Chemical Anchors Hiltistrasse 6 86916 Kaufering GERMANY

Sample Description: Hilti HIT-RE 500-SD

Date tested: May 2009

Test Method: SCAQMD method 304-91 Determination of Volatile Organic Compounds (VOC) in Various Materials as referenced by South Coast Air Quality Management District (SCAQMD) Rule 1168. The values also comply with the requirements of EPA test method #24.

Test Data:

Specification Product

LEED 2009 (LEED 3.0) LEED 2.2

IEQ-4.1: Low-Emitting Materials – Adhesives and Sealants Hilti

HIT-RE 500-SD Green Building Council of Australia Green Star Office Design 3.0, IEQ-13 Green Star Office Design 2.0, IEQ-13 Green Star Office Interiors 1.1, IEQ-11

Multipurpose Construction Adhesives; VOC Limit: 70 g/L Product contains: 4 g/L of VOC

William Welbes Vice President of Laboratory Operations

Allen Noreen, Ph.D. Technical Director

July 2014

July 2014

/7

Safety data sheetaccording to 1907/2006/EC, Article 31

Printing date 09.06.2011 Revision: 09.06.2011Version number 6

DR

1 Identification of the substance/mixture and of the company/undertaking

· Product identifier

· Trade name: Hilti HIT-RE 500-SD· Container size 330 ml, 500 ml, 1400 ml· Relevant identified uses of the substance or mixture and uses advised against· Application of the substance / the preparation Adhesive mortar for rebar and anchor fastenings in solid concrete

· Details of the supplier of the safety data sheet· Manufacturer/Supplier:Hilti Asia Ltd.17/F, Tower 6China Hong Kong City33 Canton RoadHK-Tsimshatsui, KowloonHong KongTel +852 27734 700Fax +852 2356 7311

· Informing department: see section 16· Emergency telephone number:Hilti Asia Ltd.Tel +852 27734 700Fax +852 2356 7311

2 Hazards identification

· Classification of the substance or mixture

· Classification according to Directive 67/548/EEC or Directive 1999/45/EC· Information concerning particular hazards for human and environment:The product has to be labelled due to the calculation procedure of the "General Classification guideline for preparations of the EU" in thelatest valid version.

· Classification system:The classification is in line with current EC lists. It is expanded, however, by information from technical literature and by informationfurnished by supplier companies.

· Label elements

· Labelling according to EU guidelines:The product has been classified and labelled in accordance with EC Directives / Ordinance on Hazardous Materials (GefStoffV)

· Code letter and hazard designation of product:

C CorrosiveN Dangerous for the environment

· Hazard-determining components of labelling:m-Xylylenediaminereaction product: bisphenol-A-(epichlorhydrin) epoxy resin(number average molecular weight = 700)Reaction product: bisphenol-F epichlorhydrin resin, MW 700Trimethylolpropane, (chloromethyl)oxirane polymer1,6-bis(2,3-epoxypropoxy)hexane

· Risk phrases:35 Causes severe burns.41 Risk of serious damage to eyes.20/22 Harmful by inhalation and if swallowed.43 May cause sensitisation by skin contact.51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.

· Safety phrases:1/2 Keep locked up and out of the reach of children.23 Do not breathe fumes.51 Use only in well-ventilated areas.24/25 Avoid contact with skin and eyes.36/37/39 Wear suitable protective clothing, gloves and eye/face protection.26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.28 After contact with skin, wash immediately with plenty of water and soap.61 Avoid release to the environment. Refer to special instructions/safety data sheets.

· Special labelling of certain preparations:Contains epoxy constituents. See information supplied by the manufacturer.

· Other hazards· Results of PBT and vPvB assessment· PBT: Not applicable.· vPvB: Not applicable.

(Contd. on page 2) HK

July 2014

/7



Trade name: Hilti HIT-RE 500-SD

(Contd. of page 1)

DR

· Additional information:

Hilti HIT

· Information pertaining to particular dangers for man and environment: AR 36/38 Irritating to eyes and skinR 43 May cause sensitisation by skin contactR 51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment

· Information pertaining to particular dangers for man and environment: BR 35 Causes severe burnsR 41 Risk of serious damage to eyesR 43 May cause sensitization by inhalation and skin contactR 20/22 Harmful on inhalation and if swallowedR 52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment

* 3 Composition/information on ingredients

· Chemical characterization: Mixtures· Description:2-component-foilpack, contains:Component A: Epoxy resin, Reactive diluent, inorganic fillerComponent B: Amine hardener, inorganic filler

Mixture of the substances listed below with harmless additions.

· Dangerous components:

CAS: 1477-55-0EINECS: 216-032-5

m-Xylylenediamine C R35; Xn R20/22; Xi R43

R52/53

25-40%

CAS: 25068-38-6NLP: 500-033-5

reaction product: bisphenol-A-(epichlorhydrin) epoxy resin(number average molecular weight = 700)

Xi R36/38; Xi R43; N R51/53

25-50%

CAS: 28064-14-4 Reaction product: bisphenol-F epichlorhydrin resin, MW 700 Xi R36/38; Xi R43; N R51/53

10-30%

CAS: 16096-31-4EINECS: 240-260-4

1,6-bis(2,3-epoxypropoxy)hexane Xi R36/38; Xi R43

R52/53

10-25%

CAS: 30499-70-8 Trimethylolpropane, (chloromethyl)oxirane polymer Xi R36/38; Xi R43

R52/53

2,5-10%

CAS: 14808-60-7EINECS: 238-878-4

Quartz (SiO2) 25-50%

· Dangerous components A:

CAS: 25068-38-6NLP: 500-033-5

reaction product: bisphenol-A-(epichlorhydrin) epoxy resin(number average molecular weight = 700)

Xi R36/38; Xi R43; N R51/53

CAS: 28064-14-4 Reaction product: bisphenol-F epichlorhydrin resin, MW 700 Xi R36/38; Xi R43; N R51/53

CAS: 16096-31-4EINECS: 240-260-4

1,6-bis(2,3-epoxypropoxy)hexane Xi R36/38; Xi R43

R52/53

CAS: 30499-70-8 Trimethylolpropane, (chloromethyl)oxirane polymer Xi R36/38; Xi R43

R52/53

CAS: 14808-60-7EINECS: 238-878-4

Quartz (SiO2)

· Dangerous components B:

CAS: 1477-55-0EINECS: 216-032-5

m-Xylylenediamine C R35; Xn R20/22; Xi R43R52/53

CAS: 14808-60-7EINECS: 238-878-4

Quartz (SiO2)

· Additional information For the wording of the listed risk phrases refer to section 16. HK

(Contd. on page 3)

July 2014

/7




(Contd. of page 2)

DR

4 First aid measures

· Description of first aid measures· General information Instantly remove any clothing soiled by the product.· After inhalationTake affected persons into the open air and position comfortablySeek medical treatment in case of complaints.

· After skin contact Instantly wash with water and soap and rinse thoroughly. If skin irritation persist, call a physician.· After eye contactCall a doctor immediately.Rinse opened eye for several minutes under running water.Protect unharmed eye.If splashed into the eyes, seek immediate treatment from an eye doctor or clinic.

· After swallowingDo not induce vomiting; immediately call for medical help.Rinse out mouth and then drink plenty of water.

· Information for doctor· Most important symptoms and effects, both acute and delayed Allergic reactions

5 Firefighting measures

· Extinguishing media· Suitable extinguishing agents Water spray, carbon dioxide (CO2), carbon dioxide blanket, foam, or dry powder.· For safety reasons unsuitable extinguishing agents Water with full jet.· Special hazards arising from the substance or mixtureCan be released in case of fireNitrogen oxides (NOx)Carbon monoxide (CO)Under certain fire conditions, traces of other toxic gases cannot be excluded.

· Advice for firefighters· Protective equipment: In the event of fire, wear self contained breathing apparatus· Additional information Dispose of fire debris and contaminated fire fighting water in accordance with official regulations.

* 6 Accidental release measures

· Personal precautions, protective equipment and emergency proceduresWear protective equipment. Keep unprotected persons away.Wear protective clothing.Use personal protective equipment. Ensure adequate ventilation. Remove all sources of ignition.

· Environmental precautions:Do not allow product to reach sewage system or water bodies.Do not allow to enter the ground/soil.

· Methods and material for containment and cleaning up:Collect mechanically.Clean the accident area carefully; suitable cleaners are:organic solventEnsure adequate ventilation.Dispose of contaminated material as waste according to item 13.

· Reference to other sectionsSee Section 7 for information on safe handlingSee Section 8 for information on personal protection equipment.See Section 13 for information on disposal.

7 Handling and storage

· Handling· Precautions for safe handlingThe usual precautionary measures should be adhered to general rules for handling chemicals.Use only in well ventilated areas.Take note of emission threshold.Check the expiry date: see imprint on manifold (month/year). Do not use expired mortar!

· Information about protection against explosions and fires: Keep ignition sources away - Do not smoke.

· Conditions for safe storage, including any incompatibilities· Storage· Requirements to be met by storerooms and containers: Keep in a cool, dry and dark place; 5 °C to 25 °C.· Information about storage in one common storage facility: Store away from foodstuffs.· Further information about storage conditions: Protect from heat and direct sunlight.

· Storage classAs per VCI (1991) storage classification concept.


July 2014

/7




(Contd. of page 3)

DR

8A

8 Exposure controls/personal protection

· Control parameters· Components with limit values that require monitoring at the workplace:The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.

· Additional information: The lists that were valid during the compilation were used as basis.

· Exposure controls· Personal protective equipment· General protective and hygienic measuresThe usual precautionary measures should be adhered to general rules for handling chemicals.Do not eat, drink or smoke while working.Do not inhale gases / fumes / aerosols.Avoid contact with the eyes and skin.Use skin protection cream for preventive skin protection.Clean skin thoroughly immediately after handling the product.Ensure that washing facilities are available in the work place.Do not carry cleaning cloths impregnated with the product in trouser pockets.Keep away from foodstuffs, beverages and food.Take off immediately all contaminated clothingStore protective clothing separately.Wash hands during breaks and at the end of the work.

· Breathing equipment:Not necessary if room is well-ventilated.In case of brief exposure or low pollution use breathing filter apparatus. In case of intensive or longer exposure use breathing apparatusthat is independent of circulating air.

· Recommended filter device for short term use: Filter AX· Protection of hands:Protective glovesAvoid direct contact with the chemical/ the product/ the preparation by organizational measures.Use gloves of stable material (e.g. Nitrile) - if necessary tricoted to improve the wearability.The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.Only use chemical-protective gloves with CE-labelling of category III.

· Material of glovesNitrile rubber, NBRThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturerto manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advanceand has therefore to be checked prior to the application.

· Penetration time of glove materialThe exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.

· As protection from splashes gloves made of the following materials are suitable: Nitrile rubber, NBR· Not suitable are gloves made of the following materials:Natural rubber, NRLeather glovesStrong gloves

· Eye protection:Tightly sealed safety glasses.Gauze gogglesFace protection

· Body protection: Protective work clothing.

9 Physical and chemical properties

· Information on basic physical and chemical properties· General Information· Appearance:

Form: pastyColour: Component A: grey

Component B: redMixture: red

· Odour: Amine-like

· pH-value: Component A: 7Component B: 11,5Mixture: 11,5Not applicable.

· Change in conditionMelting point/Melting range: Not determinedBoiling point/Boiling range: > 200°C


July 2014

/7




(Contd. of page 4)

DR

· Flash point: >100°C (DIN 53213)

· Self-inflammability: Product is not selfigniting.

· Danger of explosion: Product is not explosive.

· Vapour pressure at 20°C: 0,04 hPa

· Density at 20°C 1,47 g/cm³ (DIN 51757)

· Solubility in / Miscibility withWater: Unsoluble

· Viscosity:dynamic at 20°C: 50 Pa.s (DIN 53788)kinematic at 20°C: >20 s (DIN 53211/4)

· Solvent content:Organic solvents: 0 %Water: 0 %

10 Stability and reactivity

· Reactivity· Chemical stability· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.· Possibility of hazardous reactions No dangerous reactions known· Hazardous decomposition products: No dangerous decomposition products known

11 Toxicological information

· Information on toxicological effects· Acute toxicity:· Primary irritant effect:· on the skin: Strong caustic effect on skin and mucous membranes.· on the eye:Strong caustic effect.Strong irritant with the danger of severe eye injury.

· Sensitization: Sensitization possible by skin contact.· Additional toxicological information:The product shows the following dangers according to the calculation method of the General EC Classification Guidelines for Preparationsas issued in the latest version:HarmfulCorrosiveIrritant

12 Ecological information

· Toxicity· Acquatic toxicity: No further relevant information available.· Ecotoxical effects:· Remark: Toxic for fish· Additional ecological information:· According to recipe contains the following heavy metals and compounds according to EC guideline NO. 76/464 EC: None· General notes:Avoid transfer into the environment.The product contains materials that are harmful to the environment.Also poisonous for fish and plankton in water bodies.Toxic for aquatic organismsWater hazard class 2 (German Regulation) (Self-assessment): hazardous for water.

· Results of PBT and vPvB assessment· PBT: Not applicable.· vPvB: Not applicable.

* 13 Disposal considerations

· Waste treatment methods· RecommendationMust not be disposed of together with household garbage. Do not allow product to reach sewage system.Hand over to disposers of hazardous waste.Full or only partially emptied cartridges must be disposed of as special waste in accordance with official regulations.


July 2014

/7




(Contd. of page 5)

DR

· European waste catalogue

08 00 00 WASTES FROM THE MANUFACTURE, FORMULATION, SUPPLY AND USE (MFSU) OF COATINGS (PAINTS,VARNISHES AND VITREOUS ENAMELS), ADHESIVES, SEALANTS AND PRINTING INKS

08 04 00 wastes from MFSU of adhesives and sealants (including waterproofing products)

08 04 09* waste adhesives and sealants containing organic solvents or other dangerous substances

20 00 00 MUNICIPAL WASTES (HOUSEHOLD WASTE AND SIMILAR COMMERCIAL, INDUSTRIAL AND INSTITUTIONALWASTES) INCLUDING SEPARATELY COLLECTED FRACTIONS

20 01 00 separately collected fractions (except 15 01)

20 01 27* paint, inks, adhesives and resins containing dangerous substances

· Uncleaned packagings:· Recommendation:Disposal must be made according to official regulations.Dispose of packaging according to regulations on the disposal of packagings.Empty packs: May be disposed via the local Green Dot collecting system or EAK waste material code 150106 (mixed packaging materials)

* 14 Transport information

· Land transport ADR/RID (cross-border)· ADR/RID-GGVS/E Class: 8 Corrosive substances

9 Miscellaneous dangerous substances and articles.· UN-Number: 3259 / PG II

3077 / PG III· UN proper shipping name: AMINES, SOLID, CORROSIVE, N.O.S. (m-Xylylenediamine)

ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S. (Bisphenol A/F Epoxy Resin)· Tunnel restriction code E

· Maritime transport IMDG:· IMDG Class: 8

9 · UN Number: 3259 / PG II

3077 / PG III· Label 8

9 · EMS Number: F-A, S-B

F-A, S-F· Marine pollutant: yes· Correct technical name: AMINES, SOLID, CORROSIVE, N.O.S (m-Xylylenediamine)

ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S (Bisphenol A/F Epoxy Resin)· Remarks: Limited Quantity (LQ)

1 kg5 kg

· Air transport ICAO-TI and IATA-DGR:· ICAO/IATA Class: 8

9 · UN/ID Number: 3259 / PG II

3077 / PG III· Label 8

9 · Correct technical name: AMINES, SOLID, CORROSIVE, N.O.S (m-Xylylenediamine)

ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S (Bisphenol A/F Epoxy Resin)· Remarks: Packing Instruction No.

UN 3259: 859UN 3077: 956

All packed in one

· Special precautions for user Not applicable.

· Transport/Additional information:

· HS-Code: 3214 10 10: Glaziers' putty, grafting putty, resin cements, caulking compounds and other mastics

15 Regulatory information

· Safety, health and environmental regulations/legislation specific for the substance or mixture

· Designation according to EC guidelines:The product has been classified and labelled in accordance with EC Directives / Ordinance on Hazardous Materials (GefStoffV)


July 2014

/7




(Contd. of page 6)

DR

· Code letter and hazard designation of product:

C CorrosiveN Dangerous for the environment

· Hazard-determining components of labelling:m-Xylylenediaminereaction product: bisphenol-A-(epichlorhydrin) epoxy resin(number average molecular weight = 700)Reaction product: bisphenol-F epichlorhydrin resin, MW 700Trimethylolpropane, (chloromethyl)oxirane polymer1,6-bis(2,3-epoxypropoxy)hexane

· Risk phrases:35 Causes severe burns.41 Risk of serious damage to eyes.20/22 Harmful by inhalation and if swallowed.43 May cause sensitisation by skin contact.51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.

· Safety phrases:1/2 Keep locked up and out of the reach of children.23 Do not breathe fumes.51 Use only in well-ventilated areas.24/25 Avoid contact with skin and eyes.36/37/39 Wear suitable protective clothing, gloves and eye/face protection.26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.28 After contact with skin, wash immediately with plenty of water and soap.61 Avoid release to the environment. Refer to special instructions/safety data sheets.

· Special designation of certain preparations:Contains epoxy constituents. See information supplied by the manufacturer.

· National regulationsCouncil Directive 89/391/EEC of 12 June 1989 on the introduction of measures to encourage improvements in the safety and health ofworkers at work. Article 12 Training of workers

· Information about limitation of use: Employment restrictions concerning young persons must be observed.· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.

16 Other informationThese data are based on our present knowledge. However, they shall not constitute a guarantee for any specific product features and shallnot establish a legally valid contractual relationship.

· Relevant phrasesR20/22 Harmful by inhalation and if swallowed.R35 Causes severe burns.R36/38 Irritating to eyes and skin.R43 May cause sensitisation by skin contact.R51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.R52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.

· Department issuing data specification sheet:Hilti Entwicklungsgesellschaft mbHHiltistrasse 6D-86916 KauferingTel.: +49 8191 906310Fax: +49 8191 906826e-mail: [email protected]

· Contact: Monika Mönch· * Data compared to the previous version altered.

HK

July 2014

July 2014

Job

/ App

licat

ion

Ref

eren

ce

Dat

ePr

ojec

t Nam

eC

ontr

acto

rPr

oduc

t Nam

eAp

plic

atio

n

Aug‐12

Hong

Kon

g University

Red

evelop

men

tInjectable m

ortar H

IT‐RE 50

0‐SD

/330

/1marble / g

ranite fixing

Jul‐1

2Macau

Studio City

Injectable m

ortar H

IT‐RE 50

0‐SD

/330

/1rebar fastening

Sep‐12

Macau

Studio City

Injectable m

ortar H

IT‐RE 50

0‐SD

/330

/1rebar fastening

Sep‐12

Macau

Studio City

Injectable m

ortar H

IT‐RE 50

0‐SD

/330

/1structural steel / I‐be

am fixing

Sep‐12

Macau

Studio City

PAUL Y CO

NST CO LTD

Injectable m

ortar H

IT‐RE 50

0‐SD

/330

/1rebar fastening

Mar‐13

Macau

Studio City

Injectable m

ortar H

IT‐RE 50

0‐SD

/330

/1rebar fastening

Mar‐13

MTR

‐ South Island

Line

KIER

LAING O'ROURK

E KA

DEN JV

Injectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Feb‐13

The Ve

netia

n Casino

Resort

Injectable m

ortar H

IT‐RE 50

0‐SD

/330

/1rebar fastening

Sep‐13

MTR

‐ South Island

Line

MTR

CLInjectable m

ortar H

IT‐RE 50

0‐SD

/500

/1electrical se

rvices fixing

Nov

‐13

Kai Tak Develop

men

t Injectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Mar‐13

MTR

‐ South Island

Line

MTR

CLInjectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Apr‐13

MTR

‐ South Island

Line

MTR

CLInjectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Jan‐14

MTR

‐ South Island

Line

MTR

CLInjectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Mar‐14

MTR

‐ South Island

Line

MTR

C LInjectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Mar‐14

New

World ‐ Pak Ko

ng Residen

tial

NEW

WORLD

Injectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Apr‐14

New

World ‐ Pak Ko

ng Residen

tial

NEW

WORLD

Injectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

May‐14

New

World ‐ Pak Ko

ng Residen

tial

NEW

WORLD

Injectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Feb‐14

Galaxy Maga Re

sort

Hsin Cho

ngInjectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Feb‐14

Macau

Studio City

PAUL Y YA

U LEE

JVInjectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Jun‐13

Macau

Studio City

Injectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

May‐13

Macau

Studio City

Injectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

May‐14

MGM Cotai

CHINA STAT

E (HONG KONG) ‐ CHINA

Injectable m

ortar H

IT‐RE 50

0‐SD

/500

/1shear con

nector fixing

70

1-7

04

To

we

r A

, Ma

nu

life

Fia

nci

al C

en

tre

, 22

3 W

ai Y

ip S

tre

et,

Kw

un

To

ng

, Kw

olo

on

, H

on

g K

on

gH

otli

ne

: 82

28

81

18

1

July 2014

Job

/ App

licat

ion

Ref

eren

ce

Dat

ePr

ojec

t Nam

eC

ontr

acto

rPr

oduc

t Nam

eAp

plic

atio

n

May‐14

InterCon

nental, H

oliday Inn and Co

smop

olita

n (Parcel 3)

Injectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

Nov

‐13

Galaxy Maga Re

sort

Hsin Cho

ngInjectable m

ortar H

IT‐RE 50

0‐SD

/500

/1catch fence fixing

Nov

‐13

Macau

Studio City

PAUL Y YA

U LEE

JVInjectable m

ortar H

IT‐RE 50

0‐SD

/500

/1rebar fastening

70

1-7

04

To

we

r A

, Ma

nu

life

Fia

nci

al C

en

tre

, 22

3 W

ai Y

ip S

tre

et,

Kw

un

To

ng

, Kw

olo

on

, H

on

g K

on

gH

otli

ne

: 82

28

81

18

2

July 2014

Hilti HIT-RE500-SD Injection Adhesive with HI6 5 1 · Hilti HIT-RE500-SD Injection Adhesive with...

Documents

Transcript of Hilti HIT-RE500-SD Injection Adhesive with HI6 5 1 · Hilti HIT-RE500-SD Injection Adhesive with...