HERC-ALLOY 800 CHAIN - Psicología

RIRIIGGGG ING G G & & ATATTACHCHCHMEMEMENTNTNTSSS

74 WWW.CMWORKS.COM

CHAIN SLINGS & COMPONENTS HERC-ALLOY 800® (GRADE 80)

CHAIN & RIGGING ATTACHMENTS (CMRP-6)

PHONE: 800.888.0985

CHAIN SLINGS &

COMPONENTS

HERC-ALLOY 800® CHAIN

A higher strength heat treated alloy steel chain primarily used as a sling component for overhead lifting

Can be used in rigging and tie down applications where a lighter weight, higher strength chain is desirable

Recommended for overhead lifting by NACM, ASME, and OSHA

BENEFITS & FEATURES

Chain Size(in.)

Working Load Limit(lbs.)

Nominal Chain Dimensions (in.) Per Foot Per Drum

Material Diameter

A

Inside Length

B

Inside Width

CProduct

CodeWeight(lbs./ft.)

Approximate Number of

Links(per ft.)

Product Code

Length(ft.)

Weight(lbs.)

7/32 2,100 0.22 0.68 0.31 607020 0.44 17.8 677010 800 3549/32 3,500 0.28 0.88 0.40 607028 0.73 13.6 677011 500 3655/16 4,500 0.32 1.02 0.46 607031 0.91 11.8 – – –3/8 7,100 0.39 1.25 0.57 607037 1.44 9.6 677013 500 7191/2 12,000 0.51 1.44 0.73 607050 2.55 8.3 677015 300 7655/8 18,100 0.63 1.78 0.86 607062 3.82 6.8 677016 200 7653/4 28,300 0.79 2.23 1.07 607075 5.95 5.4 677017 100 5957/8 34,200 0.88 2.25 1.14 607087 7.76 5.3 677018 100 7761 47,700 1.00 3.07 1.49 607101 9.41 3.9 677019 100 941

1-1/4 72,300 1.25 3.92 1.74 607128 14.20 3.1 677070 90 1,278

A

B

C

1000

WORKING LOAD LIMIT: 2,100 TO 72,300 LBS.

INSPECTION, CARE & USE

1. Determine the weight and configuration of the load(s) to be lifted.

2. Determine the type of chain sling required, according to weight and configuration. (See page 31 for standard sling configurations.)

3. Determine the size of the body chain according to the working load limits. Be sure to take into consideration the effect of the required angle. The working load limit is the maximum load in pounds which should be applied in direct tension to a straight length of chain. Note: Working load limit can be affected by angles of loading, type of hitch used, environmental conditions such as hot and cold temperatures, and D/d ratio.

4. Determine the reach required to give the desired angle. The reach is measured from the upper bearing surface of the master link to the bearing surface of the lower attachment. If chain slings are to be used in pairs and are to be matched for reach, please indicate when ordering.

5. Know share of load on pick points and location of center of gravity.

HOW TO SELECT AND ORDER THE PROPER CHAIN SLING

See pages 26 through 32 for more information, or visit us at www.cmworks.com

HERC-ALLOY 800®

RIRIR GGGGGGININING GG && & ATATTTAACHCHHMENTNTTSSS

75WWW.CMWORKS.COMCHAIN & RIGGING ATTACHMENTS (CMRP-6)

PHONE: 800.888.0985


CHAI

N SL

INGS

&

COM

PONE

NTS

Adjusters on slings allow for easy and safe take up of chain when applications require shorter leg lengths or when lifting objects of abnormal sizes. There are two styles of adjusters: Style A and Style B. Style A is commonly used for shorter reach slings and consists of a hook attached to the link. Style B has 12" of chain in between link and hook gives you more flexibility on longer slings. Note: Adjusters are also available on single, double, triple and quad slings.

SINGLE LEG(VERTICAL)

DOUBLE(2 LEGS)

TRIPLE(3 LEGS)

QUADRUPLE(4 LEGS)

DOUBLE BASKET

SINGLEBASKET

SINGLEADJUSTABLE

DOUBLEADJUSTABLE

MAGNETSLING

HERC-ALLOY 800® CHAIN SLINGS

DOUBLE ENDLESS

SINGLEENDLESS

Chain Size(in.)

Working Load Limits for Sling Types Show Above

Single(1 leg)

SingleChoker Double (2 legs) Triple (3 legs) Quad (4 legs) Single

BasketDouble Basket

Single Endless

Double Endless

90º(lbs.)

90º(lbs.)

60º(lbs.)

45º(lbs.)

30º(lbs.)

60º(lbs.)

45º(lbs.)

30º(lbs.)

60º(lbs.)

45º(lbs.)

30º(lbs.)

60º(lbs.)

60º(lbs.)

90º(lbs.)

60º(lbs.)

7/32 2,100 1,700 3,600 3,000 2,100 5,500 4,400 3,200 5,500 4,400 3,200 3,600 5,500 2,100 3,6009/32 3,500 2,800 6,100 4,900 3,500 9,100 7,400 5,200 9,100 7,400 5,200 6,100 9,100 3,500 6,1005/16 4,500 3,600 7,800 6,400 4,500 11,700 9,500 6,800 11,700 9,500 6,800 7,800 11,700 4,500 7,8003/8 7,100 5,700 12,300 10,000 7,100 18,400 15,100 10,600 18,400 15,100 10,600 12,300 18,400 7,100 12,3001/2 12,000 9,600 20,800 17,000 12,000 31,200 25,500 18,000 31,200 25,500 18,000 20,800 31,200 12,000 20,8005/8 18,100 14,500 31,300 25,600 18,100 47,000 38,400 27,100 47,000 38,400 27,100 31,300 47,000 18,100 31,3003/4 28,300 22,600 49,000 40,000 28,300 73,500 60,000 42,400 73,500 60,000 42,400 49,000 73,500 28,300 49,0007/8 34,200 27,400 59,200 48,400 34,200 88,900 72,500 51,300 88,900 72,500 51,300 59,200 88,900 34,200 59,2001 47,700 38,200 82,600 67,400 47,700 123,900 101,200 71,500 123,900 101,200 71,500 82,600 123,900 47,700 82,600

1-1/4 72,300 57,800 125,200 102,200 72,300 187,800 153,400 108,400 187,800 153,400 108,400 125,200 187,800 72,300 125,200

American Society of Mechanical Engineers ASME B30.9, the National Association of Chain Manufacturers (NACM) and the Occupation Safety & Health Administration (OSHA) recommend only the use of alloy steel chain for overhead lifting, i.e. sling chain. Slings may be constructed by the user using Herc-Alloy® chain, Herc-Alloy 1000 or Herc-Alloy 800 chain and attachments.

SINSINNNGLEGLEGLEGLE LELELE LEGG(VERTICAL)

DOUDOUDOUDOUBLEBLEBLEBLE TRIPLE QUADRUPLE MAGMAGNETNETSLING

For more information on standard sling configurations, see page 31 or visit us online at www.cmworks.com

HERC

-ALL

OY 8

00®


76 WWW.CMWORKS.COM



PHONE: 800.888.0985

CHAIN SLINGS &

COMPONENTS

Trade Size(in.)


Product Code

Nominal Dimensions (in.)Weight(lbs.)Material

DiameterA

Inside Length

B

Inside Width

C 1/2 5,100 M50P 0.50 5.00 2.50 0.905/8 7,700 M62P 0.63 6.00 3.00 1.753/4 10,600 M75P 0.75 6.00 3.00 2.351 20,400 M100P 1.00 8.00 4.00 6.00

A

B

C

D

Trade Size(in.)

Working Load Limit

(lbs.)Catalog Number

Product Code

Nominal Dimensions (in.)

Weight(lbs.)

Type and Size of Grade 80 Chain Sling

(in.)

Material Diameter

A

InsideLength

B

InsideWidth

CSingle Double

Standard Sizes (DUAL RATED THROUGH 1-3/4" SIZE ONLY)3/8 5,400 HA40 555231 0.41 3.00 1.50 0.33 7/32 & 9/32 7/32 1/2 8,600 HA50 555232 0.56 5.00 2.50 1.02 3/8 9/32 3/4 17,600 HA75 555235 0.75 5.50 2.75 2.08 1/2 3/8 1 30,000 HA100 555238 1.00 7.00 3.50 4.59 5/8 & 3/4 1/2

1-1/4 45,200 HA125 555240 1.25 8.75 4.38 9.31 7/8 5/8 1-1/2 70,600 HA150 555243 1.50 10.50 5.25 15.60 1 3/4 & 7/81-3/4 105,900 HA175 555246 1.75 12.00 6.00 24.40 1-1/4 1

2* 88,900 HA200 554949 2.00 14.00 7.00 38.00 1-1/4 1 2-1/4* 125,200 HA225 554951 2.25 16.00 8.00 55.00 – 1-1/4 2-3/4* 187,800 HA275 554957 2.75 16.00 9.00 84.84 – –

Special Sizes (NOT DUAL RATED)1 18,200

N/A

554969 1.00 8.00 4.00 5.25

N/A N/A

1-1/4 22,800 554942 1.25 12.00 6.00 12.081-1/2 36,700 554944 1.50 14.00 7.00 20.161-1/2 42,900 554970 1.50 12.00 6.00 17.601-3/4 57,100 554945 1.75 14.00 7.00 27.92

2 77,800 554952 2.00 16.00 8.00 43.00

A

B

C

Accepts both Herc-Alloy® 1000 & 800 chain and components Durable orange powder coated finish May be used for mechanical and welded sling assemblies 100% proof tested

BENEFITS & FEATURES


FORGED MASTER LINK GRADE 80

MASTER LINK DUAL RATED FOR USE WITH HA800 OR HA1000

Quench and tempered alloy steel Fatigue rated to Grade 80 specifications 100% proof tested Raised markings for better identification Durable orange powder coated finish

NOTE: Standard sizes dual rated through 1-3/4" only. Special sizes not dual rated.

BENEFITS & FEATURES


120º

Can be used with included angles up to 120°

120º


HERC-ALLOY 800®



PHONE: 800.888.0985


CHAI

N SL

INGS

&

COM

PONE

NTS

Chain Size(in.)

Trade Size(in.)


Product Code

Nominal Dimensions (in.)Weight(lbs.)Material Diameter

AInside Length

BInside Width

C5/8 & 3/4 1-3/4 73,500 554966 1.75 8.00 5.000 18.96 7/8 & 1 2 123,900 554950 2.00 8.98 5.000 28.04 1 & 1/4 2-1/2 187,800 554965 2.50 11.92 6.500 54.73

A

B

C

Trade Size(in.)

Working Load Limit (lbs.)Product

Code

Nominal Dimensions (in.) Flat Dimensions (in.)Weight(lbs.)

Type and Size of Chain Sling (in.)

With ChainWith Wire

Rope & Synthetics

Material Diameter

A

Inside Length

B

Inside Width

CWidth Thickness Single Double

7/16 4,200 3,360ML040

0.44 4.13 2.290.94 0.28

0.50 7/32 & 9/32 7/32ML040NF – –

1/2 5,750 4,600ML050

0.56 4.84 2.690.94 0.28

1.02 – 7/32ML050NF – –

5/8 9,000 7,200ML063

0.63 5.29 2.981.22 2.81

1.34 3/8 9/32ML063NF – –

3/4 14,200 11,360ML075

0.75 6.61 3.721.41 0.40

2.36 1/2 3/8ML075NF – –

7/8 17,300 13,840ML087

0.88 7.35 4.141.56 0.44

3.60 – –ML087NF –

1 26,500 21,200ML100

1.00 7.53 4.301.56 0.53

5.20 5/8 1/2ML100NF –

1-1/4 37,400 29,920ML125

1.25 9.26 5.291.56 0.68

9.60 3/4 & 7/8 5/8ML125NF – –

1-1/2 53,000 42,400 ML150 1.50 11.03 6.30 – – 16.20 1 3/41-3/4 72,150 57,720 ML175 1.75 12.86 7.35 – – 25.10 – 7/8

2 94,200 75,360 ML200 2.00 14.70 8.40 – – 41.00 1-1/4 12-1/4 119,200 95,360 ML225 2.25 16.54 9.45 – – 58.00 – –2-1/2 147,150 117,720 ML250 2.50 18.38 10.50 – – 74.90 – 1-1/42-3/4 178,050 142,440 ML275 2.75 20.21 11.55 – – 99.80 – –

A

B

C

Fla

t

Designed to accept HA800 chain, wire rope and synthetic attachments

Use with mechanical and welded assemblies Sizes up to 1-1/4" available with flats to

accommodate Omega link 100% proof tested Extra wide body makes these links

ideal for wire rope applications and use with Omegaloks. Master link with flat allows for easy installation of these attachments.

BENEFITS & FEATURES


FLAT BOTTOM MASTER LINK GRADE 80

MASTER LINK WITH & WITHOUT FLATS HERC-ALLOY 800®

Designed to accept HA800 chain and components Made from alloy steel Extra wide width allows for larger hook usage 100% proof tested

BENEFITS & FEATURES


Weight

A

80

NOTE: *Master link with flats are available through 1-1/4" only Part numbers with"NF" are for master links WITHOUT flats

120º


HERC

-ALL

OY 8

00®


78 WWW.CMWORKS.COM



PHONE: 800.888.0985

CHAIN SLINGS &

COMPONENTS

Fla

t

A

B

C

D

E

F

A

B

C

D

E

F

Trade Size(in.)

Working Load Limit(lbs.) Complete

Assembly Product

Code

Master Link Nominal Dimensions (in.)

Intermediate Link Nominal Dimensions (in.)

Weight(lbs.)

Type and Size of Chain Sling

(in.)

With Chain

With Wire Rope &

SyntheticProduct

CodeMaterial Diameter

A

Inside Length

B

Inside Width

CProduct


D

Inside Length

E

Inside Width

FTriple Quad

1/2 5,750 4,600 SA050 ML050 0.56 4.84 2.69 ML040 0.44 4.13 2.29 1.8 – –5/8 9,000 7,200 SA063 ML063 0.63 5.29 2.98 ML050 0.56 4.84 2.69 2.9 7/32 7/323/4 14,000 11,200 SA075 ML075 0.75 6.61 3.72 ML063 0.63 5.29 2.98 5.5 9/32 9/327/8 17,300 13,840 SA087 ML087 0.88 7.35 4.14 ML063 0.63 5.29 2.98 6.3 – –1 26,500 21,200 SA100 ML100 1.00 7.53 4.30 ML075 0.75 6.61 3.72 10.2 3/8 3/8

1-1/4 37,400 29,920 SA125 ML125 1.25 9.26 5.29 ML100 1.00 7.53 4.30 20.0 1/2 1/21-1/2 53,000 42,400 SA150 ML150 1.50 11.03 6.30 ML100 1.00 7.53 4.30 26.6 – –1-3/4 72,150 57,720 SA175 ML175 1.75 12.86 7.35 ML125 1.25 9.26 5.29 44.3 5/8 5/8

2 94,200 75,360 SA200 ML200 2.00 14.70 8.40 ML150 1.50 11.03 6.30 73.4 3/4 3/42-1/4 119,200 95,360 SA225 ML225 2.25 16.54 9.45 ML175 1.75 12.86 7.35 108.2 7/8 7/82-1/2 147,150 117,720 SA250 ML250 2.50 18.38 10.50 ML200 2.00 14.70 8.40 156.9 1 12-3/4 178,050 142,400 SA275 ML275 2.75 20.21 11.55 ML200 2.00 14.70 8.40 181.0 – –

Trade Size(in.)

Catalog Number

Working Load Limit

at 60º(lbs.)

Product Code

Master Link Nominal Dimensions (in.) Intermediate Link Nominal Dimensions (in.)Weight(lbs.)

Type & Size of Chain Sling (in.)

Material Diameter

A

Inside Length

B

InsideWidth

C

Material Diameter

D

InsideLength

E

InsideWidth

FTriple Quad

1/2 SA50 7,000 555274 0.56 5.00 2.50 0.44 1.75 1.06 1.35 7/32 7/323/4 SA75 11,200 555275 0.75 5.50 2.75 0.47 1.56 0.88 2.64 9/32 9/321 SA100 22,900 555276 1.00 7.00 3.50 0.78 2.63 1.50 7.25 3/8 3/8

1-1/4 SA125 39,000 555277 1.25 8.75 4.38 0.91 3.13 1.75 13.51 1/2 1/21-1/2 SA150 58,700 555278 1.50 10.50 5.25 1.13 4.00 2.25 24.28 5/8 5/81-3/4 SA175 91,700 555279 1.75 12.00 6.00 1.50 5.25 2.75 44.58 3/4 & 7/8 3/4 & 7/8

2* HA200-SA 88,900 554980 2.00 14.00 7.00 1.53 5.25 2.75 57.34 7/8 7/82-1/4* HA225-SA 123,900 554981 2.25 16.00 8.00 1.78 6.00 3.00 81.48 1 12-3/4* HA275-SA 187,800 554983 2.75 16.00 9.00 2.00 7.00 3.50 126.66 1-1/4 1-1/4

Designed for triple and quad branch Herc-Alloy® chain slings

Consists of an oblong master link and two welded master coupling links

Accepts both Herc-Alloy 1000 & 800 chain and components

Durable orange powder coated finish

May be used for mechanical or welded sling assemblies

100% proof tested

Extra wide body is ideal for wire rope applications

Sizes up to 1-1/4" intermediate links available with flats to accommodate Omega links

BENEFITS & FEATURES


WIDE BODY SUB-ASSEMBLY WITH FLATS HERC-ALLOY 800®

SUB-ASSEMBLY DUAL RATED FOR USE WITH HA800 & HA1000

Designed to accept Herc-Alloy 800® chain, wire rope and synthetic attachments


100% proof tested May be used for mechanical

and welded sling assemblies

BENEFITS & FEATURES


Fla

t

ensions (in.) Type & Siz

800 & HA1000

* Grade 80 only

NOTE: Master link with flats are available through 1-1/4" only

120º


120º


HERC-ALLOY 800®

HERC

-ALL

OY® 8

00RI

GGIN

G HA

RDW

ARE

RIGGING HARDWARE


PHONE: 800.888.0985

Trade Size(in.)

Working Load Limit

(lbs.)Catalog Number

Product Code

Nominal Dimensions (in.)

Weight(lbs.)

Type and Size of Grade 80 Chain Sling

(in.)

Material Diameter

A

InsideLength

B

InsideWidth

CSingle Double

Standard Sizes (DUAL RATED THROUGH 1-3/4" SIZE ONLY)3/8 5,400 HA40 555231 0.41 3.00 1.50 0.33 7/32 & 9/32 7/32 1/2 8,600 HA50 555232 0.56 5.00 2.50 1.02 3/8 9/32 3/4 17,600 HA75 555235 0.75 5.50 2.75 2.08 1/2 3/8 1 30,000 HA100 555238 1.00 7.00 3.50 4.59 5/8 & 3/4 1/2

1-1/4 45,200 HA125 555240 1.25 8.75 4.38 9.31 7/8 5/8 1-1/2 70,600 HA150 555243 1.50 10.50 5.25 15.60 1 3/4 & 7/81-3/4 105,900 HA175 555246 1.75 12.00 6.00 24.40 1-1/4 1

2* 88,900 HA200 554949 2.00 14.00 7.00 38.00 1-1/4 1 2-1/4* 125,200 HA225 554951 2.25 16.00 8.00 55.00 – 1-1/4 2-3/4* 187,800 HA275 554957 2.75 16.00 9.00 84.84 – –

Special Sizes (NOT DUAL RATED)1 18,200

N/A

554969 1.00 8.00 4.00 5.25

N/A N/A

1-1/4 22,800 554942 1.25 12.00 6.00 12.081-1/2 36,700 554944 1.50 14.00 7.00 20.161-1/2 42,900 554970 1.50 12.00 6.00 17.601-3/4 57,100 554945 1.75 14.00 7.00 27.92

2 77,800 554952 2.00 16.00 8.00 43.00

A

B

C

Accepts both Herc-Alloy® 1000 & 800 chain and components Durable orange powder coated finish May be used for mechanical and welded sling assemblies 100% proof tested

BENEFITS & FEATURES


MASTER LINK DUAL RATED FOR USE WITH HA800 OR HA1000

NOTE: Standard sizes dual rated through 1-3/4" only. Special sizes not dual rated.

120º


Trade Size(in.)


Product Code

Nominal Dimensions (in.)Weight(lbs.)Material

DiameterA

Inside Length

B

Inside Width

C 1/2 5,100 M50P 0.50 5.00 2.50 0.905/8 7,700 M62P 0.63 6.00 3.00 1.753/4 10,600 M75P 0.75 6.00 3.00 2.351 20,400 M100P 1.00 8.00 4.00 6.00

A

B

C

D

FORGED MASTER LINK GRADE 80

Quench and tempered alloy steel Fatigue rated to Grade 80 specifications 100% proof tested Raised markings for better identification Durable orange powder coated finish

BENEFITS & FEATURES


120º


RIGGING HARDWARE

RIGGING HARDWARE

94 WWW.CMWORKS.COMCHAIN & RIGGING ATTACHMENTS (CMRP-6)

PHONE: 800.888.0985

Trade Size(in.)

Working Load Limit (lbs.)Product

Code

Nominal Dimensions (in.) Flat Dimensions (in.)Weight(lbs.)


With ChainWith Wire

Rope & Synthetics

Material Diameter

A

Inside Length

B

Inside Width

CWidth Thickness Single Double

7/16 4,200 3,360ML040

0.44 4.13 2.290.94 0.28

0.50 7/32 & 9/32 7/32ML040NF – –

1/2 5,750 4,600ML050

0.56 4.84 2.690.94 0.28

1.02 – 7/32ML050NF – –

5/8 9,000 7,200ML063

0.63 5.29 2.981.22 2.81

1.34 3/8 9/32ML063NF – –

3/4 14,200 11,360ML075

0.75 6.61 3.721.41 0.40

2.36 1/2 3/8ML075NF – –

7/8 17,300 13,840ML087

0.88 7.35 4.141.56 0.44

3.60 – –ML087NF –

1 26,500 21,200ML100

1.00 7.53 4.301.56 0.53

5.20 5/8 1/2ML100NF –

1-1/4 37,400 29,920ML125

1.25 9.26 5.291.56 0.68

9.60 3/4 & 7/8 5/8ML125NF – –

1-1/2 53,000 42,400 ML150 1.50 11.03 6.30 – – 16.20 1 3/41-3/4 72,150 57,720 ML175 1.75 12.86 7.35 – – 25.10 – 7/8

2 94,200 75,360 ML200 2.00 14.70 8.40 – – 41.00 1-1/4 12-1/4 119,200 95,360 ML225 2.25 16.54 9.45 – – 58.00 – –2-1/2 147,150 117,720 ML250 2.50 18.38 10.50 – – 74.90 – 1-1/42-3/4 178,050 142,440 ML275 2.75 20.21 11.55 – – 99.80 – –

A

B

C

Flat

Designed to accept HA800 chain, wire rope and synthetic attachments

Use with mechanical and welded assemblies Sizes up to 1-1/4" available with flats to

accommodate Omega link 100% proof tested Extra wide body makes these links

ideal for wire rope applications and use with Omegaloks. Master link with flat allows for easy installation of these attachments.

BENEFITS & FEATURES


MASTER LINK WITH & WITHOUT FLATS HERC-ALLOY 800®

NOTE: *Master link with flats are available through 1-1/4" only Part numbers with"NF" are for master links WITHOUT flats

120º


HERC

-ALL

OY® 8

00RI

GGIN

G HA

RDW

ARE

RIGGING HARDWARE


PHONE: 800.888.0985

Flat

A

B

C

D

E

F

Trade Size(in.)

Working Load Limit(lbs.) Complete

Assembly Product

Code

Master Link Nominal Dimensions (in.)

Intermediate Link Nominal Dimensions (in.)

Weight(lbs.)


With Chain

With Wire Rope &

SyntheticProduct


A

Inside Length

B

Inside Width

CProduct


D

Inside Length

E

Inside Width

FTriple Quad

1/2 5,750 4,600 SA050 ML050 0.56 4.84 2.69 ML040 0.44 4.13 2.29 1.8 – –5/8 9,000 7,200 SA063 ML063 0.63 5.29 2.98 ML050 0.56 4.84 2.69 2.9 7/32 7/323/4 14,000 11,200 SA075 ML075 0.75 6.61 3.72 ML063 0.63 5.29 2.98 5.5 9/32 9/327/8 17,300 13,840 SA087 ML087 0.88 7.35 4.14 ML063 0.63 5.29 2.98 6.3 – –1 26,500 21,200 SA100 ML100 1.00 7.53 4.30 ML075 0.75 6.61 3.72 10.2 3/8 3/8

1-1/4 37,400 29,920 SA125 ML125 1.25 9.26 5.29 ML100 1.00 7.53 4.30 20.0 1/2 1/21-1/2 53,000 42,400 SA150 ML150 1.50 11.03 6.30 ML100 1.00 7.53 4.30 26.6 – –1-3/4 72,150 57,720 SA175 ML175 1.75 12.86 7.35 ML125 1.25 9.26 5.29 44.3 5/8 5/8

2 94,200 75,360 SA200 ML200 2.00 14.70 8.40 ML150 1.50 11.03 6.30 73.4 3/4 3/42-1/4 119,200 95,360 SA225 ML225 2.25 16.54 9.45 ML175 1.75 12.86 7.35 108.2 7/8 7/82-1/2 147,150 117,720 SA250 ML250 2.50 18.38 10.50 ML200 2.00 14.70 8.40 156.9 1 12-3/4 178,050 142,400 SA275 ML275 2.75 20.21 11.55 ML200 2.00 14.70 8.40 181.0 – –

100% proof tested May be used for mechanical

and welded sling assemblies Extra wide body is ideal for

wire rope applications Sizes up to 1-1/4" intermediate

links available with flats to accommodate Omega links

WIDE BODY SUB-ASSEMBLY WITH FLATS HERC-ALLOY 800®

Designed to accept Herc-Alloy

800® chain, wire rope and synthetic attachments


BENEFITS & FEATURES


Flat

NOTE: Master link with flats are available through 1-1/4" only

120º


DNV MASTER SUB-ASSEMBLIES

Certified and serialized to meet DNV 2.7-1 and 2.7-3 Offshore Container Specifications and 2.22 Lifting Appliances Requirements.

Design factor of 5:1 or higher in accordance with DNV 2.7-1 requirements.

Welds exceed Charpy V impact strength of 27 Joules at -20ºC (20 ft-lb, at -4ºF) as per DNV 2.7-1.

Exceed ASTM A952 specifications for lifting components.

Designed to meet ASME B30.9 requirements. Links are 100% proof tested at the manufacturing facility at two times the WLL.

BENEFITS & FEATURES

WORKING LOAD LIMIT: 17-1/2 TO 50 TON

Designed for use with chain, wire rope and synthetic slings.

Made from superior triple alloy steel with a galvanized coating for protection against corrosion.

Certification of compliance supplied with each shipment. CG3 documentation available upon request.

Available in sizes from 1-1/4" to 2" diameter. Other sizes available upon request.

Fla

t

A

B

C

D

E

F

Master Sub-Assemblies meeting DNV requirements are used to build slings in conjunction with DNV Shackles. These products are designed for use in offshore saltwater environments for general load securement applications, such as during the installation and removal of offshore platforms or transportation of cargo container units.

th

th

meter.

AA

C

container units.

Trade Size(in.)

Working Load LimitProduct

Code

Master Link Dimensions (in.) Intermediate Link Dimensions (in.)Weight(lbs.)ton lbs.

Material Diameter

A

Inside Length

B

Inside Width

C

Material Diameter

D

Inside Length

E

Inside Width

F1-1/4 17.64 35,280 SA125DNV 1.25 8.75 4.38 1.25 8.75 4.38 27.81-1/2 27.56 55,125 SA150DNV 1.50 10.50 5.25 1.50 10.50 5.25 48.01-3/4 38.59 77,175 SA175DNV 1.75 12.00 6.00 1.75 12.00 6.00 75.0

2 50 100,000 SA200DNV 2.00 14.00 7.00 2.00 14.00 7.00 113.7



PHONE: 800.888.0985


CHAI

N SL

INGS

&

COM

PONE

NTS

Trade Size(in.)


ProductCode

Dimensions (in.)Weight(lbs.)Diameter

AInside Length

BInside Width

CInside Width

D

1/2 3,500 554320 0.56 5.50 2.50 0.54 1.013/4 7,100 554326 0.75 6.06 2.75 0.63 2.08 1 12,000 554332 1.00 7.63 3.50 0.75 4.59

1-1/4 18,100 554337 1.25 9.25 4.38 1.00 9.16

B

C D

A

Trade Size(in.)

Working Load Limit

(lbs.)Product

Code

Dimensions (in.)Weight(lbs.)


Material Diameter

A

InsideLength

B Single Double Triple Quadruple

1/2 3,500 554611 0.51 2.50 0.52 7/32 & 9/32 – – –5/8 6,100 554613 0.63 3.00 0.99 – 7/32 7/32 7/323/4 10,500 554615 0.75 4.00 1.86 3/8 9/32 9/32 9/327/8 12,300 554617 0.88 4.00 2.60 1/2 – – –1 18,400 554619 1.00 4.00 3.45 5/8 3/8 – –

1-1/4 28,300 554623 1.25 5.00 6.98 3/4 1/2 3/8 3/81-1/2 31,300 554627 1.50 6.00 11.80 – – – –1-3/4 53,000 554630 1.75 7.00 18.70 7/8 & 1 5/8 1/2 1/2

2 73,500 554635 2.00 8.00 27.90 1-1/4 7/8 5/8 5/82-1/4 88,900 554636 2.25 9.00 39.90 – – 3/4 3/42-1/2 141,000 554640 2.50 10.00 54.60 – 1 7/8 & 1 7/8 & 1

A

B

Made from alloy material Proof tested at two times WLL Durable orange powder coated finish

BENEFITS & FEATURES


MASTER RING HERC-ALLOY 800®

GRAB LINK HERC-ALLOY 800®

Made from alloy material Proof tested at two times the WLL Economical chain adjuster for single slings Durable orange powder coated finish

BENEFITS & FEATURES


Chain Sling (in.)

HERC

-ALL

OY 8

00®


80 WWW.CMWORKS.COM



PHONE: 800.888.0985

CHAIN SLINGS &

COMPONENTS

Size(in.)

Working Load Limit

(lbs.)

Completed Unit Load Pin Kit Dimensions (in.)

Product Code

Weight (lbs.)

Standard Package

Product Code

Weight (lbs.) A B C D E F G

7/32 2,100 664021-2 0.12 36 R664021-2 0.01 0.25 0.25 1.40 0.50 0.58 1.21 0.449/32 3,500 664028-2 0.26 36 R664028-2 0.02 0.34 0.31 1.94 0.75 0.70 1.51 0.563/8 7,100 664038-2 0.59 36 R664038-2 0.05 0.48 0.50 2.41 0.88 0.91 2.09 0.801/2 12,000 664050-2 1.42 24 R664050-2 0.12 0.66 0.70 3.51 1.29 1.41 2.96 1.155/8 18,100 664062-2 2.35 12 R664062-2 0.20 0.78 0.81 4.06 1.50 1.70 3.52 1.403/4 28,300 664075-2 3.67 12 R664075-2 0.30 0.96 0.94 4.78 1.80 1.97 4.11 1.717/8 34,200 664089-2 5.98 6 R664089-2 0.40 1.16 1.05 5.25 1.97 2.09 4.95 1.881 47,700 664100-2 9.47 – R664100-2 0.70 1.32 1.25 6.00 2.31 2.37 5.87 2.33

1-1/4 72,300 664125-2 16.61 – R664125-2 1.20 1.57 1.53 6.81 2.17 2.98 7.04 2.67

Size(in.)

Working Load Limit

(lbs.)StandardPackage

Product Code Dimensions (in.)Weight(lbs.)Completed

UnitLoad Pin

Retainer Pin B D E G H L M T

9/32 3,500 12 644128 595780 602326 1.36 2.30 0.98 2.81 0.33 0.36 1.45 0.43 0.40 3/8 7,100 12 644138 595781 495821 1.90 2.82 1.25 3.57 0.45 0.51 1.77 0.57 1.02 1/2 12,000 12 644150 595782 495822 2.31 3.52 1.56 4.44 0.59 0.63 2.26 0.70 1.92 5/8 18,100 5 644162 595785 495823 2.87 4.46 2.00 5.45 0.75 0.75 2.72 0.88 3.20

L PIN

M

B

H

T

D

E

G

Fraction and metric markings Durable orange powder coated finish 100% proof tested Fatigue rated to Grade 80 specifications For use with master link with flats

(see page 77)

BENEFITS & FEATURES


OMEGALOK CONNECTOR HERC-ALLOY 800®

HAMMERLOK® HERC-ALLOY 800®

Used for overhead lifting slings to connect chain branches to the master link and the hook to attachments.

Constructed of drop forged alloy steel Can be used with Grade 80 chain Must be matched to chain size Do not use for chain repair or splicing Meets ASTM A952 standards.

BENEFITS & FEATURES


OY 800Y

HERC-ALLOY 800®



PHONE: 800.888.0985


CHAI

N SL

INGS

&

COM

PONE

NTS

Size(in.)

Working Load Limit


Product Code Dimensions (in.)Weight(lbs.)With

LatchWithout Latch

Latch Kit B D E G H I K L M N O P S

7/32 2,700 10 558618 458618 4X458321 1.50 3.04 1.03 5.06 0.38 0.66 1.48 0.75 3.75 1.17 0.98 0.94 0.96 0.89/32 4,300 10 558622 458622 595523 1.63 3.50 1.50 5.25 0.44 0.73 1.59 0.75 3.75 1.19 1.20 1.05 1.06 1.103/8 8,800 10 558625 458625 595525 2.06 4.33 1.88 6.64 0.56 0.95 2.19 0.94 4.78 1.44 1.45 1.28 1.31 1.901/2 15,000 5 558628 458628 595528 2.63 5.50 2.25 8.16 0.75 1.17 2.56 1.13 5.69 1.78 1.94 1.66 1.63 4.305/8 22,600 5 558629 458629 595529 3.06 6.34 2.63 9.66 0.88 1.44 2.63 1.31 6.50 2.03 2.38 2.19 1.75 7.303/4 35,300 Bulk 558630 458630 595530 3.50 7.83 3.00 11.38 1.00 1.69 3.44 1.50 7.81 2.50 2.83 2.51 2.19 12.507/8* 34,200 Bulk 558332 458732 595532 3.88 8.59 3.38 12.72 1.09 1.94 3.88 1.69 8.75 2.78 3.22 2.84 2.38 18.101* 47,700 Bulk 558333 458733 595533 4.31 9.59 4.00 14.23 1.22 2.14 4.25 1.88 9.88 3.13 3.55 3.09 2.88 22.60

1-1/4* 72,300 Bulk 558335 458735 595535 5.31 11.56 4.66 17.00 1.50 2.62 4.64 2.31 11.50 3.88 4.25 3.89 3.41 47.00

B

N

G

K

D

E

P

M

I

O

L

H

S

For use with both Grade 80 & 100 chain Available with and without a latch Quench and tempered alloy steel Clevlok head design 100% proof tested and fatigue rated Durable orange powder coated finish Improved forged latch

(hook available with or without latch) Replacement pin and latch kit available New CE compliant hooks and latches Meets EN 1677, ASTM A953 and

ASME B30.10 standards

BENEFITS & FEATURES


CLEVLOK® SLING HOOK DUAL RATED FOR USE WITH HA800 OR HA1000

EYE SLING HOOK DUAL RATED FOR USE WITH HA800 OR HA1000

For use with both Grade 80 & 100 chain Available with and without latch Quench and tempered alloy steel 100% proof tested Fatigue rated Hook available with and without latch

(replacement latch available) Durable orange powder coated finish

BENEFITS & FEATURES


Size(in.)

Working Load Limit

(lbs.)Standard Package

Product Code Dimensions (in.)Weight(lbs.)With

LatchWithout Latch

Latch Kit

Alloy Load Pin

RetainingPin D G H I L M O P R

7/32 2,700 10 657716 557716 4X455321 SP595778 495826 3.05 5.00 0.31 0.66 0.28 0.96 1.13 0.94 3.45 1.109/32 4,300 10 657718 557718 4X455322 595780SP 495825 3.53 5.55 0.38 0.75 0.36 0.83 1.32 1.11 3.75 1.20 3/8 8,800 10 657719 557719 4X455325 595781 495825 4.54 6.93 0.47 1.00 0.51 1.06 1.34 1.51 4.58 2.21 1/2 15,000 5 657720 557720 4X455328 595782 495823 5.48 8.28 0.58 1.33 0.63 1.38 1.87 1.55 5.59 4.22 5/8 22,600 5 657721 557721 4X455329 SP595783P 495849 6.20 9.61 0.71 1.47 0.75 1.69 2.11 1.83 6.44 6.64 3/4 35,300 Bulk 657722 557722 4X455330 595786 495824 7.63 11.79 0.88 1.88 0.94 2.09 2.55 2.51 7.74 11.22

* Herc-Alloy 800® only

HERC

-ALL

OY 8

00®

M (MIN)

R G

M (MIN)

D

P

R

P

G

D I

O

L

H H

L

RIGGING HARDWARE

RIGGING HARDWARE


PHONE: 800.888.0985

C

L

R

B

A

I

G

H

S

D

T

O

SWIVEL RIGGING HOOK

BENEFITS & FEATURES Design factor 5:1 Pre-drilled for latches Hooks furnished with

or without latches Powder coated orange Hooks are heat treated,

quenched and tempered

WORKING LOAD LIMIT: 1 TO 22 TONS

StandardPackage

Alloy Zinc Plated Latch Kit (optional)Product

Code

Dimensions (in.)

LatchKit

Weight(lbs.)WLL*

(tons)

Product CodeA B C D G H I L R S T Owithout

LatchwithLatch

10 1 M3402A M3502A 4X1302 2.00 1.11 1.31 3.06 0.87 1.05 0.63 5.83 4.63 0.38 0.87 0.93 4X1302 1.0510 1-1/2 M3403A M3503A 4X1303 2.50 1.38 1.50 3.33 0.94 1.11 0.71 6.83 5.44 0.50 0.97 0.97 4X1303 1.5610 2 M3404A M3504A 4X1304 3.00 1.65 1.75 3.67 1.06 1.21 0.88 7.76 6.25 0.63 1.03 1.06 4X1304 2.5010 3 M3405A M3505A 4X1305 3.00 1.65 1.75 4.20 1.27 1.43 0.94 8.40 6.49 0.63 1.16 1.16 4X1305 3.2010 5 M3407A M3507A 4X1307 3.50 1.77 2.00 5.11 1.44 1.63 1.31 9.76 7.53 0.75 1.53 1.41 4X1307 5.36

Bulk 7 M3409A M3509A 4X1309 4.75 2.39 2.75 6.24 1.82 2.01 1.68 12.42 9.67 1.00 1.94 1.69 4X1309 10.56Bulk 11 M3411A M3511A 4X1311 5.50 2.55 3.25 7.69 2.25 2.63 1.88 14.89 12.06 1.13 2.46 2.22 4X1311 19.00Bulk 15 M3415A M3515A 4X1315 6.00 2.47 3.50 8.37 2.59 2.94 2.19 15.79 11.95 1.25 2.62 2.23 4X1315 26.75Bulk 22 M3422A M3522A 4X1322 7.75 3.82 4.75 10.19 3.00 3.50 2.69 21.18 16.68 1.50 2.74 3.05 4X1322 51.80

* Working Load Limits in Metric Tons

T

)

C

L

R

B

A

K

G

H

K

D

T

O

J

RIGGING HOOK

BENEFITS & FEATURES Load rating marked on each hook body Design factor 5:1 Pre-drilled latch tab allows addition of latch Carbon hooks have a clear protective

coating to resist rust and for cleaner handling

Alloy hooks have orange powder coated finish

WORKING LOAD LIMIT: 3/4 TO 15 TONS

StandardPackage

Carbon Alloy Zinc Plated Latch

Kit (optional)Product

Code

Dimensions (in.)

Latch Kit

Weight(lbs.)

Clear Finish Painted Orange

WLL*(tons)

Product CodeWLL*(tons)

Product CodeA B C D G H J K L O R Twithout

LatchwithLatch

without Latch

withLatch

10 3/4 M6402C M6502C 1 M6402A M6502A 4X1302 1.50 0.75 0.38 3.12 0.87 1.01 0.93 0.63 4.37 0.93 3.13 0.87 4X1302 0.6610 1 M6403C M6503C 1-1/2 M6403A M6503A 4X1303 1.75 0.88 0.44 3.37 0.94 1.11 0.97 0.71 5.04 0.97 3.66 0.97 4X1303 1.125 1-1/2 M6404C M6504C 2 M6404A M6504A 4X1304 2.13 1.10 0.50 3.80 1.06 1.21 1.02 0.74 5.65 1.02 4.09 1.03 4X1304 1.465 2 M6405C M6505C 3 M6405A M6505A 4X1305 2.50 1.25 0.64 4.20 1.26 1.43 1.19 0.94 6.55 1.16 4.67 1.16 4X1305 2.425 3 M6407C M6507C 5 M6407A M6507A 4X1307 3.08 1.56 0.77 5.11 1.44 1.63 1.50 1.38 7.97 1.41 5.78 1.53 4X1307 4.105 5 M6409C M6509C 7 M6409A M6509A 4X1309 3.88 1.98 0.94 6.24 1.82 2.01 1.78 1.68 10.07 1.69 7.31 1.94 4X1309 8.16– 7-1/2 M6411C M6511C 11 M6411A M6511A 4X1311 4.69 2.44 1.13 7.89 2.25 2.63 2.38 1.88 12.41 2.19 9.03 2.52 4X1311 15.60– 10 M6415C M6515C 15 M6415A M6515A 4X1315 5.34 2.84 1.25 8.53 2.75 3.10 2.50 2.03 14.05 2.30 10.21 2.54 4X1315 21.58– 15 M6422C M6522C 22 M6422A M6522A 4X1322 6.63 3.50 1.56 10.30 3.15 3.62 3.30 2.60 17.53 3.12 12.81 2.73 4X1322 39.89

* Working Load Limits in Metric Tons. Note: Other finishes are available as special orders.

J


82 WWW.CMWORKS.COM



PHONE: 800.888.0985

CHAIN SLINGS &

COMPONENTS

B

P

H

E

K

D

E

M

G

L

T

Quench and tempered alloy steel Fatigue rated Built without lugs to avoid catching

when slipping into tight clearance Durable orange powder coated finish Replacement pin available

BENEFITS & FEATURES


CLEVLOK® GRAB HOOK WITHOUT CRADLE HERC-ALLOY 800®

CLEVLOK® CRADLE GRAB HOOK DUAL RATED FOR USE WITH HA800 OR HA1000

For use with both Grade 80 & 100 chain Unique cradle grab design Quench and tempered alloy steel Fatigue rated Durable orange powder coated finish Replacement pin available

BENEFITS & FEATURES


Size(in.)

Working Load Limit


Product Code Dimensions (in.)Weight(lbs.)Completed

UnitLoad Pin

Retainer Pin B D E G H K L M P T

9/32 3,500 10 659232 595780 602326 1.36 1.91 0.36 3.70 0.33 1.04 0.36 2.29 0.76 0.81 0.63/8 7,100 10 659235 595781 495821 1.90 2.78 0.47 4.81 0.45 1.49 0.51 2.87 1.03 1.06 1.3 1/2 12,000 5 659238 595782 495822 2.31 3.62 0.59 6.35 0.59 1.98 0.63 3.78 1.51 1.38 2.5 5/8 18,100 5 659239 595783 495823 2.87 4.41 0.75 7.74 0.75 2.39 0.75 4.82 1.80 1.69 4.4

Note: If used as a choker, working load limit should be reduced by 20%.

* 3/4" is Herc-Alloy 800® only. Hook shape/style differs from photo and dimension drawing shown.

H

M

G

R

L

P

D

J

K

Size(in.)

Working Load Limit

(lbs.)Product

CodeStandard PackageQuantity

Dimensions (in.)Weight(lbs.)D G H J K L M P R

7/32 2,700 659718 10 1.62 3.21 0.31 0.75 0.94 0.28 0.31 0.62 1.98 0.509/32 4,300 659722 10 2.18 3.39 0.38 0.82 0.97 0.36 0.38 0.82 1.86 0.633/8 8,800 659725 10 2.72 4.33 0.47 1.18 1.29 0.51 0.74 1.03 2.47 1.301/2 15,000 659728 5 3.65 5.27 0.65 1.39 2.01 0.63 0.60 1.19 3.04 2.105/8 22,600 659729 5 4.50 6.54 0.77 1.55 2.42 0.75 0.77 1.41 3.76 4.203/4* 28,300 659430 Bulk 5.23 9.08 0.88 2.05 2.88 0.91 0.88 1.87 5.50 10.24


HERC-ALLOY 800®



PHONE: 800.888.0985


CHAI

N SL

INGS

&

COM

PONE

NTS

Size(in.)

Working Load Limit


Product Code

Dimensions (in.)Weight(lbs.)B D E G H I K L M N O R

9/32 4,300 5 474798 1.56 4.73 2.50 6.45 0.47 1.00 1.56 0.63 4.75 2.50 1.23 0.25 2.43/8 8,800 5 474799 2.00 5.72 3.00 7.88 0.63 1.27 1.88 0.80 5.77 3.00 1.50 0.31 4.51/2 15,000 5 474800 2.50 6.75 3.50 9.38 0.75 1.50 2.22 1.00 6.88 3.50 1.75 0.38 7.15/8 22,600 5 474801 3.00 7.81 4.00 10.97 0.88 1.81 2.63 1.25 8.06 4.00 2.03 0.44 11.63/4 35,300 Bulk 474802 3.50 9.10 4.50 12.81 1.00 2.20 3.00 1.50 9.25 4.50 2.56 0.50 20.07/8* 34,200 Bulk 474503 4.00 10.09 5.00 14.23 1.13 2.25 3.38 1.70 10.38 5.00 2.78 0.56 26.01* 47,700 Bulk 474504 4.50 11.55 5.50 16.17 1.29 2.63 3.75 2.13 11.56 5.50 3.45 0.62 36.8

1-1/4* 72,300 Bulk 474505 5.13 12.87 6.00 18.03 1.38 3.17 4.25 2.33 12.88 6.00 3.81 0.75 58.4

H

B

L

N

R (SPHER.)

K

E

D (REF)

O

G (REF)

M

I

Size(in.)

Working Load Limit


Product Code

Dimensions (in.) Weight(lbs.)B D E G H I K L M P

7/32 3,200 10 559724 1.20 1.68 0.31 3.22 0.33 0.92 0.99 0.55 2.20 0.69 0.359/32 4,300 10 559725 1.40 1.93 0.36 3.72 0.39 1.07 1.13 0.63 2.57 0.76 0.553/8 8,800 10 559737 1.78 2.86 0.47 4.81 0.52 1.65 1.49 0.78 3.27 1.02 1.061/2 15,000 5 559750 2.28 3.63 0.59 6.36 0.63 1.81 2.15 1.06 4.23 1.53 2.005/8 22,600 5 559762 2.75 4.53 0.75 7.62 0.75 2.13 2.65 1.22 5.06 1.80 5.403/4 35,300 Bulk 559775 3.50 5.23 0.91 9.54 1.00 2.88 3.52 1.52 6.70 1.85 9.007/8* 34,200 Bulk 559387 3.75 5.69 1.00 9.63 1.00 3.00 3.75 1.75 6.50 2.12 10.401* 47,700 Bulk 559100 4.31 7.00 1.19 12.44 1.22 3.88 4.31 1.88 8.09 3.12 20.90

1-1/4* 72,300 Bulk 559124 5.38 8.50 1.53 15.56 1.56 2.50 5.50 2.25 10.50 3.50 40.00

B

H

G

K

E

P

D

M

L

I

For use with both Grade 80 & 100 chain Unique cradle grab design Quench and tempered alloy steel 100% proof tested Fatigue rated Durable orange powder coated finish

BENEFITS & FEATURES


EYE CRADLE GRAB HOOK DUAL RATED FOR USE WITH HA800 OR HA1000

EYE FOUNDRY HOOK DUAL RATED FOR USE WITH HA800 OR HA1000

For use with both Grade 80 & 100 chain Throat opening up to 6" Quench and tempered alloy steel Fatigue rated Durable orange powder coated finish

BENEFITS & FEATURES




Weight


HERC

-ALL

OY 8

00®

RIGGING HARDWARE

RIGGING HARDWARE


PHONE: 800.888.0985

Alloy Shank HookWeight(lbs.)

LatchKit

ProductCode

Max Shank

Diameter(in.)

LatchHole(in.)

Dimensions (in.)

Working Load Limit

(ton)Product

Code D F G H J K L O P R X Y Z

1 M1302A 0.65 4X1302 0.72 0.14 3.09 1.25 0.87 1.01 0.91 0.63 5.44 0.88 2.12 2.35 0.66 2.22 0.69 1-1/2 M1303A 0.80 4X1303 0.79 0.19 3.37 1.38 0.94 1.11 0.97 0.71 5.92 0.91 2.27 2.59 0.73 2.39 0.80

2 M1304A 1.47 4X1304 0.86 0.18 3.75 1.50 1.04 1.21 1.06 0.88 6.45 1.00 2.58 2.75 0.79 2.66 1.00 3 M1305A 1.85 4X1305 1.11 0.18 4.23 1.63 1.25 1.43 1.17 0.94 7.42 1.16 2.84 3.16 0.96 3.01 1.035 M1307A 4.04 4X1307 1.30 0.20 5.16 2.00 1.44 1.63 1.48 1.38 8.80 1.41 3.52 3.85 1.24 3.52 1.277 M1309A 7.25 4X1309 1.56 0.20 6.24 2.50 1.82 2.01 1.78 1.68 10.72 1.69 4.59 4.70 1.49 4.02 1.56

L

F

D

J w/o Latch

P

Z

Y

R

G

X

H

O

T

K

K

Z

Working Load Limit(lbs.) With Handle Without Handle Dimensions (in.)

At Tip(ton)

At bottom of Hook

(ton)Product

CodeWeight(lbs.)

Product Code

Weight(lbs.) A B C D E F G H I M

1 7-1/2 M129H 7.0 M129 6.8 3 1.44 0.78 7.34 3.75 1.28 1.25 3.93 10.09 6.58

I

H

C

E

G

F

D

B

M

A

5:1 design factor Quench and tempered alloy steel Long tapered point designed for easy grab

in rings, pear links, eye bolts or lifting holes Durable orange powder coated finish Do not load last 1" of the tip

BENEFITS & FEATURES

WORKING LOAD LIMIT: 7-1/2 TONS

SORTING HOOK HERC-ALLOY 800®

SHANK HOOK HERC-ALLOY 800®

Heat treated alloy steel provides strength without bulk or weight

Pre-drilled boss allows for latch Shank hooks are supplied

unthreaded, but can be supplied threaded as a special order item

Shank hooks made from other material (bronze, stainless steel, etc.) available upon request

BENEFITS & FEATURES

WORKING LOAD LIMIT: 1 TO 7 TONS

K

The following should be observed: Shanks are not intended for internal threading or swaging.

To obtain maximum strength threads should be class 1 or 2.

Thread engagement in nut or object must be a minimum of 1-1/2 times the thread diameter. Insufficient thread engagement can result in loss of load.

HERC

-ALL

OY® 8

00RI

GGIN

G HA

RDW

ARE

RIGGING HARDWARE


PHONE: 800.888.0985

Size(in.)

Working Load Limit(lbs.) Product Code

Dimensions (in.) Weight(lbs.)A B C D

9/32 210 562228 0.28 4.50 1.13 1.13 0.153/8 410 562237 0.38 6.00 1.50 1.50 0.351/2 870 562250 0.56 7.50 2.00 2.00 1.045/8 1,120 562262 0.63 9.00 2.50 2.50 1.563/4 1,730 562275 0.75 10.50 3.00 3.00 2.607/8 2,370 562287 0.88 12.00 3.50 3.50 4.201 2,920 562300 1.00 13.00 4.00 4.00 6.00

1-5/32 3,150 562310 1.13 15.00 4.50 4.50 9.301-1/4 4,450 562325 1.25 16.00 5.00 5.00 11.701-3/8 6,100 562337 1.38 17.00 5.50 5.50 15.401-1/2 6,250 562350 1.50 18.00 6.00 6.00 19.50

B

C

A

C

D

R

R

R

W

M

B

L

N

A

C

D

T

Size(in.)

Product Code

Working Load Limit

(lbs.)

Dimensions (in.) Weight(lbs.)A B C D L M N T W R

9/32 462528 3,600 2.00 1.75 2.50 0.94 1.00 3.48 0.13 0.63 2.50 0.31 2.80 3/8 462537 7,050 2.63 2.97 4.31 1.24 1.13 6.53 0.19 0.75 2.75 0.50 5.70 1/2 462550 11,400 3.50 4.00 4.38 1.50 1.50 6.98 0.28 1.00 3.50 0.50 13.00

Made from alloy material Designed to handle plate steel Durable orange powder coated finish Available as components

or attached to certified slings

BENEFITS & FEATURES


PLATE HOOK HERC-ALLOY 800®

ALLOY “S” HOOK HERC-ALLOY 800®

Made from alloy material Proof tested at two times WLL Durable orange powder coated finish WLL embossed on hooks Custom sizes available upon request Serialized upon request

Other sizes available

BENEFITS & FEATURES

WORKING LOAD LIMIT: 210 TO 6,250 LBS.

NEVER USE PLATE HOOKS ON A QUAD SLINGS. To lift a plate with a quad sling, a spreader or beam is required and hooks would go on the end of double chain slings that would be attached to each end of the beam.

RIGGING HARDWARE

RIGGING HARDWARE


PHONE: 800.888.0985

Working Load Limit(ton)

Product Code

Dimensions (in.) Weight(lbs.)A B C D E

1 M134 7.56 5.63 1.13 0.50 0.44 2.56

REPLACEMENT HOOK WITH LATCHWORKING LOAD LIMIT: 1 TON

A B

C

D

EBENEFITS & FEATURES Easy installation Bolt, nut, and cotter pin provides

safe and secure attaching points Self colored finish Easy installation

ProductCode

Working Load Limit

(lbs. per set of 4)

Dimensions (in.)Weight(lbs.)A B C D E F G

CLB40 88,100 5.984 7.126 1.772 1.457 2.874 2.953 1.575 39.7

E

A

F

B

C

D

G

2

0

CLB CONTAINER LIFTING LUGS

BENEFITS & FEATURES

REDUCTION OF WORKING LOAD LIMITAngle of lift must be specified when ordering CLB lifting lugs

Spring-loaded bolt to prevent accidental release

Mounted horizontally at the side of the container in either upper or lower holes

Easy installation and removal – simply insert and turn to install

Designed to eliminate the dangerous use of standard hooks

Lugs cannot drop out when slings become slack

Lugs can be used for left hand or right hand turns

For maximum capacity, use a lifting beam in conjunction with CLB lifting lugs

WORKING LOAD LIMIT: 88,100 LBS. (PER SET OF 4)

Supplied in sets of 4, CLB Lifting Lugs serve as flexible lashing points for the transportation of containers.

40T40T

32T

36º

50º

50T

Vertical

HERC-ALLOY 800 CHAIN - Psicología

Documents

Transcript of HERC-ALLOY 800 CHAIN - Psicología