HarmanKardon SB15 230 Actsub

harman/kardon Service Manual

SB 15/230 Soundbar with wireless subwoofer

CONTENTS

PACKAGE GUIDE AND PARTS, CENTER 10 PACKAGE GUIDE AND PARTS, SUB 11 EXPLODED VIEW AND PARTS, CENTER 12 EXPLODED VIEW AND PARTS, SUB 13 ELECTRICAL PARTS LIST 14 SCHEMATIC DIAGRAMS 16 PCB DRAWINGS 20-30

ESD WARNING 2 INTRO AND CONTENTS 3 CONTROLS AND CONNECTIONS 4 SUBWOOFER CONNECTIONS 5 PROGRAMMING THE SOUNDBAR 6 TROUBLESHOOTING 7 SPECIFICATIONS 8 NEW ON/OFF EXPLANATION 9

Released EU2010 Harman Consumer Group, Inc. Rev 0, 05/2010 8500 Balboa Boulevard Northridge, California 91329

harman/kardon SB 15/230 Service Manual

of 30

Each precaution in this manual should be followed during servicing.

Components identified with the IEC symbol in the parts list are special significance to safety. When replacing a component identified with

, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the

parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably

insulated from the supply circuit before retuming the product to the customer.

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and

semiconductor "chip" components.

The following techniques should be used to help reduce the incidence of component damage caused by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on

your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to

prevent electrostatic charge build-up or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges

sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement

ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the

chassis or circuit assembly into which the device will be installed.

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together

or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.

CAUTION :


of 30

22 3

ENG

LISH

Harman Kardon® SB 15/230 Included

Introduction Thank you for purchasing the Harman Kardon® SB 15/230 speaker system, with which you’re about to begin many years of listening enjoyment . The SB 15/230 has been custom-designed to provide the excitement and power of the cinema experience in your own living room .

While sophisticated electronics and state-of-the-art speaker components are hard at work within the SB 15/230, hookup and operation are simple .

To obtain maximum enjoyment from your new soundbar speaker system, we urge you to take a few minutes to read through this manual . This will help ensure that the connections you make are correct . In addition, a few minutes spent learning the functions of the various controls will enable you to take advantage of all the power and refinement the SB 15/230 is able to deliver .

If you have any questions about this product, its installation or its operation, please contact your dealer, the best local source of information .

Description and FeaturesThe SB 15/230 is a complete home theater speaker system that includes:

A video-shielded stereo soundbar speaker (the SB 15CNTR) with two-way dual- •driver left and right speakers and built-in 25-watt x 2 stereo amplifier

A 10-inch (250mm), 100-watt wireless powered subwoofer (the SB15SUB) •

Wall-mount brackets for the soundbar •

A 6 .5-foot (2m) stereo audio cable for connecting the system directly to your TV’s •audio output .

The SB 15CNTR soundbar contains the system’s left and right speakers and stereo amplifiers, and features digital signal processing with virtual 3D surround circuitry that creates a complete surround-sound experience without any extra speakers or wires . You can set the soundbar on a table in front of your TV, and the system includes hardware that makes it easy to mount the soundbar on the wall along with your flat-panel TV . You can program the soundbar to respond to your TV remote’s volume, power and source commands .

The SB15SUB subwoofer receives its signal from the SB 15CTR soundbar via wireless technology, so you can place it anywhere in your room without having to run any wires . Its 10-inch (250mm) woofer and built-in 100-watt amplifier deliver a movie’s impact and excitement . Other conveniences include a volume control, a phase switch for fine-tuning bass response to suit your listening environment, and an efficient switching system that senses the presence of an audio signal and automatically switches the subwoofer on .

Harman Kardon invented the high-fidelity receiver more than 50 years ago . With state-of-the-art features and time-honored circuit designs, the SB 15/230 will turn your flat-screen TV into a fun and exciting home theater .

One SB 15CNTR soundbar speaker

One SB 15SUB 10-inch (250mm) 100-watt wireless subwoofer

Two wall-mount brackets for the SB 15CNTR soundbar

One 24V DC power supply and AC power cord for the SB 15CNTR speaker

One 6 .5-foot (2m) stereo audio cable

Important If anything is missing, or if any part of your SB 15/230 system fails to operate properly, contact your dealer immediately .


of 30

44 5

Surround Mode

Button

Surround Mode

Indicator

Power Button

Power Indicator

Volume Up/Down

Buttons

Source Selector Button

Source Indicator

Power Button: When the soundbar is in the Standby mode (the Power Indicator is amber), press this button to turn the SB 15/230 system On . (The Power Indicator turns blue .) NOTE: When the soundbar is in the Standby mode, it will automatically turn On whenever it detects an audio signal at the Source 1 (analog) inputs .

When the SB 15/230 system is On:

Momentarily press the Power button to mute the SB 15/230 system . (The Power •Indicator flashes blue .)

Hold down the Power button for three seconds to put the soundbar in the Standby •mode . (The Power Indicator turns amber .) NOTE: The subwoofer will remain on for approximately 15 minutes after the audio signal ceases, then will automatically go into the Standby mode .

Surround Mode Button: This button turns the SB 15/230 system’s 3D Surround processing On and Off . The Surround Mode Indicator turns blue when 3D Surround is active, and turns white when 3D Surround is not active (normal stereo sound) . See Soundbar Surround Mode Button, on page 8, for more information .

Volume Up/Down Buttons: Press the ( – ) button to reduce the volume; press the ( + ) button to increase the volume .

Source Selector Button: This button switches between the sources connected to the Source 1 (analog) and Source 2 (digital) inputs . When Source 1 is active, the Source Indicator turns white; when Source 2 is active, the Source Indicator turns blue .

Wireless Code Switch: Selects between four different channels for the wireless subwoofer signal .

IMPORTANT: Be sure to set the subwoofer’s Wireless Code switch to the same channel that you set the soundbar’s Wireless Code switch . See Wireless Code Switches, on page 9, for more information .

EQ Switch: This switch adjusts the soundbar’s bass for either wall or table mounting . If you’re mounting the soundbar on a wall with the included wall-mount brackets, set this switch to the Wall position for the most natural-sounding bass performance . If you are placing the soundbar on a table, set the EQ switch to the Table position for the most natural-sounding bass performance .

Trim Switch: This switch adjusts the soundbar’s input sensitivity so it will work with TVs that have different audio signal output levels . See Soundbar Trim Switch, on page 9, for more information .

Source 1 Connection (analog): Use the included stereo audio cable to connect the stereo analog outputs of your TV, DVD player or cable/satellite tuner here .

Source 2 Connection (digital): If your TV, DVD player or cable/satellite tuner has a coaxial digital output, you can connect it here .

NOTE: If you connect your TV or another component to the soundbar’s Source 1 connection, you can connect a different component to the Source 2 connection .

Power Connection: Connect the included DC power supply here . See Power Connections, on page 7, for more information .

IMPORTANT: Do not connect the power supply’s AC cord to an AC outlet until you have made and verified all connections .

Power Switch: Set this switch to the On position (press the switch’s white dot) to activate the soundbar . In normal operation, this switch will be left in the On position . See Turning the Soundbar On and Off, on page 8, for more information .

Soundbar Top-Panel Controls Soundbar Rear-Panel Controls and Connections

EQ Switch

TrimSwitch

Source 2 Connection

PowerSwitch

PowerConnection

Source 1Connection

Wireless CodeSwitch


of 30

44 5

0

180

VOLUME

MIN MAX

CROSSOVER

POWER

ON

OFF

PHASE

ENG

LISH

Subwoofer Rear-Panel Controls

Crossover Knob: This knob adjusts the subwoofer’s crossover between 50Hz and 150Hz .The higher you set the Crossover knob, the higher in frequency the subwoofer will operate and the more its bass will “overlap” that of the soundbar . This adjustment helps achieve a smooth transition of bass frequencies between the subwoofer and the soundbar for a variety of different rooms and subwoofer locations . See Subwoofer Crossover Knob, on page 9, for more information .

Volume Control: Use this control to balance the subwoofer’s volume with that of the soundbar . Turn the knob clockwise to increase the subwoofer’s volume; turn it counterclockwise to decrease the subwoofer’s volume .

Phase Switch: This switch determines whether the subwoofer driver’s piston-like action moves in and out in phase with the speakers in the soundbar . If the subwoofer were to play out of phase with the soundbar speakers, some of the sound waves produced by the subwoofer or soundbar could be canceled, reducing bass performance and sonic impact . This phenomenon depends in part on the relative placement of the speakers in the room . See Subwoofer Phase Switch, on page 9, for more information .

Wireless Code Switch: Selects between four different channels for the wireless subwoofer signal . IMPORTANT: Be sure to set the soundbar’s Wireless Code switch to the same channel as you set the subwoofer’s Wireless Code switch . See Wireless Code Switches, on page 9, for more information .

AC Fuse: The SB 15SUB is factory-equipped with a T1AL/250V 1A – 250V AC fuse . If the fuse ever blows:

Unplug the power cord from the wall .1 .

Use a screwdriver to remove the blown fuse .2 .

Replace the fuse with an identical T1AL/250V 1A – 250V AC fuse .3 .

CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE THE FUSE ONLY WITH THE SAME TYPE AND RATING .

Power Cord: Plug this cord into an active, unswitched AC outlet . See Power Connections, on page 7, for more information .

Power Switch: Set this switch to the On position to activate the subwoofer . In normal operation, this switch will be left in the On position . See Turning the Subwoofer On and Off, on page 8, for more information .

Status Indicator (on top of unit, not shown): Lights blue when the subwoofer's power switch is in the On position; lights amber when the subwoofer is in Standby; turns off when the subwoofer’s Power switch is in the Off position .

Crossover Knob

Volume Knob

Phase Switch

Wireless Code

Switch

Power Cord

AC Fuse

Power Switch


of 30

1010 11

You can program the soundbar so it will respond to your TV remote’s Power, Mute, Volume Up, Volume Down and Source commands . This lets you control your whole home theater system with a single remote . Before beginning to program the soundbar, have your TV remote handy . We recommend sitting down in front of the soundbar . The steps will time-out, so read through the entire procedure before you begin .

To program the power command:

With the soundbar turned on, hold down the soundbar’s Power and Source 1 . Selector (SRC) buttons together until all the soundbar button indicators flash . This enters the learning mode .

Hold down both buttons until all indicators flash

Momentarily press the soundbar’s Power button . It will turn amber .2 .

Momentarily press

Aim the TV remote at the front of the soundbar from about 300mm-900mm 3 . (about 12-36 inches) away .

TV Remote

300mm-900mm 12"-36"

Hold down the TV remote's Power button for one second, then release it . Do this 4 . a total of four (4) times . When the soundbar has learned the power command, its Power Indicator will turn blue, and the Surround Mode and Source Selector Indicators will flash blue .

If the Power Indicator flashes amber, the procedure failed . Repeat Steps 1 – 4 . •

To program the source, volume + and volume – commands:

Follow Steps 1–4 as above, but in Steps 2 and 4, substitute the soundbar and TV remote’s Source Selector and Volume Up/Down buttons for the Power buttons .

To program the mute command:

Follow Steps 1-4 as above, but in Step 2, hold down the soundbar's Power button for 2-3 seconds . In step 4, substitute the TV remote's Mute button for its Power button .

To erase all remote programming:

Hold down the soundbar's Surround Mode and Volume Up buttons at the same time for 2-3 seconds .

Programming the Soundbar to Respond to Your TV Remote


of 30

1010 11

ENG

LISH

Troubleshooting

If the soundbar does not turn on:

Check that the soundbar power supply’s AC cord is plugged into a working AC •outlet, and that the power supply is plugged into the soundbar .

Check that the soundbar’s Power switch is in the On position . •

If the subwoofer does not turn on:

Check that the subwoofer’s power cord is plugged into a working AC outlet . •Check that the subwoofer’s Power switch is in the On position . •Check if the subwoofer’s AC fuse has blown . See • Subwoofer Rear-Panel Controls: AC fuse, on page 5, for instructions on checking and changing the fuse .

If there is no sound coming from both the soundbar and the subwoofer:

Check that the soundbar is on (the Power Indicator is illuminated blue) . •Check that the cable connecting the TV or other source component to the •soundbar is properly connected at both ends .

Check that the soundbar’s Source Selector is set to the correct source (the •Source Indicator illuminates white for Source 1 – analog, and illuminates blue for Source 2 – digital), and that the source is playing an audio signal .

Check that the system is not muted (when the system is muted, the soundbar’s •Power Indicator flashes blue) . Momentarily press the Power button to un-mute the system .

Check that the soundbar’s volume is not turned all the way down (the lowest •setting of the Volume Down button will mute the system) .

If there is no sound coming from just the subwoofer:

Check that the Subwoofer Volume Control is not turned all the way down (fully •counterclockwise) .

Check that the Wireless Code switches on the subwoofer and soundbar are both •set to the same setting number .

Move the subwoofer closer to the soundbar . (The maximum wireless operation •distance is 50 feet (15 .3m) .

If the soundbar’s sound is distorted:

Set the soundbar’s Trim switch to a lower setting . •Check the source component to see if the distortion is coming from it, and not •the soundbar .

If the system’s sound is too quiet, even when the soundbar’s volume is turned all the way up:

Set the soundbar’s Trim switch to a higher setting . •If the TV or source component is connected via a variable output, check its •instructions to be sure that the output is not turned down too low .

The bass output is not loud enough:

Turn up the subwoofer’s Volume knob . •Move the subwoofer into a corner of the room . •Move the subwoofer closer to the seating location . •

The soundbar won’t learn your TV remote’s commands:

Carefully follow steps 1 – 4 of • Programming the Soundbar to Respond to Your TV Remote, on page 9 .

Hold the TV remote 12 inches (300mm) in front of the soundbar during the •learning procedure .

Although the soundbar will learn commands from most TV remotes, there may •be some IR codes that it cannot learn .

If you press your TV remote’s Power button and the soundbar turns off when the TV turns on (or vice versa):

Press the Power button on either the soundbar or the TV (but not both) one •time . This will put them back in sync so they will turn on and off together when you press the TV remote’s Power button .


of 30

12

Specifications

SB 15/230 System

Frequency Response 50Hz–20kHz

SB 15CNTR Soundbar SB 15SUB Subwoofer

Input Rating DC 24V, 2 .5–2 .7A

Input rating: AC 230V, 50Hz, 100W

Amplifier Power 25 watts x 2

Amplifier Power 100 watts RMS

Tweeter Two 3/4" domes (one per channel), video-shielded

Woofer 10" cone, vented enclosure

Midrange Four 3" drivers (two per channel), video-shielded

Dimensions (H x W x D) 110mm x 920mm x 89mm (4-5/16" x 36-1/4" x 3-1/2")

Dimensions (H x W x D) 480mm x 380mm x 380mm (18-7/8" x 13-3/8" x 13-3/8")

Weight 8 lb (3 .6kg)

Weight 34 lb (15 .4kg)

Harman Consumer Group, Inc . 8500 Balboa Boulevard, Northridge, CA 91329 USA 516 .255 .4545 (USA only)

www .harmankardon .com

Made in China

©2009 Harman International Industries, Incorporated . All rights reserved .

Features, specifications and appearance are subject to change without notice .

Harman Kardon is a trademark of Harman International Industries, Incorporated, registered in the United States and/or other countries . Designed to Entertain is a trademark of Harman International Industries, Incorporated .

Part No . 406-000-06124-E


of 30

NEW SECTION FOR THE SB 15 OWNER’S MANUAL.

SB 15/230 How to Switch the system on:

Manually:

If the SB 15/230 is manually put into Standby on the ON/OFF Button on the SB 15 unit itself, it can only be switched back ON by manually pressing the ON/OFF button again.

Auto Turn on:

The SB 15/230 automatically enters Standby‐mode after approx. 15 minutes if no audio signal is detected. This can also be forced by learning (for example) the TV set’s remote control “Off” code into the SB 15/230 (See owner’s manual).

Due to Power saving regulations, the SB 15 does not “listen” to the Audio Inputs, unless it senses a remote signal first, which can be any kind of remote signal (it does not have to be a learned remote code ‐ turning ON the TV or sending any other infrared remote code will be enough). The remote signal will tell the SB 15/230 to start up automatically as soon as audio is detected on (first) the Digital or (second) the Analog audio Input. If no signal is detected by the Inputs, the SB 15 will go back into total Standby again after approx 15 minutes.

MATRIX OF ON/OFF FUNCTIONS.

Power OFF function SB 15 Status Way to Power On Comment

Music sense OFF.

Remote sense is OFF to avoid unit powering ON. Manual Power Off

Button on SB 15 unit Remote sense OFF. Manual Power On Button only!

SB 15 switches music sense ON by IR signal, then powers ON 5-10secs after music is sensed on either (first) digital or (second) analog Inputs.

IR Activity from any remote (TV/SAT/VCR/DVD/...) sensed by the SB 15 switches the music sense ON. There is no need to learn any remote code to do this.

Auto Standby (Automatic if audio is Off or not present for more than 15 min)

Music sense OFF, Remote sense ON.

Or press SB 15 manual Power button. SB 15 switches music sense ON by IR signal, then powers ON 5-10secs after music is sensed on either (first) digital or (second) analog Inputs.

By remote control (usually TV Remote, but any remote will do).

Music sense OFF, Remote sense ON.

Or press SB 15 manual Power button.

IR Activity from any remote (TV/SAT/VCR/DVD/...) sensed by the SB 15 switches the music sense ON. There is no need to learn any remote code to do this.


of 30


of 30

BHenriks

Rectangle

數量料號名稱編號

依ECN No. 091043 更改

保存年限: 永久

日期

表單編號:DM-4-D-013 1版

頁次版本

確認製作

客戶：JBL

機種：SB 15CNTR/230作業指示

承認

2009/12/25 0 1

352-AM04008C1334-E 16

Bottom panel 315-ABS-05231-0BAE 1

Baffle 243-030-05259-0BAE 1

20352-AM03510D112-E

依ECN No. 更改

305-ABS-05037-0BAE 2

依ECN No. 更改

Screw for Amplifier

Crossover

Tweeter 32DM20AX-HT03-E 2

Top panel 315-ABS-05230-0BAERear Enclosure

1

蔣國正蔣國正

Screw for crossover 352-AM03008C1086-E 22

Crossover 013-7600-05766-E 1

螺絲均要點膠

Side Cap

LOGO Grille 329-030-05464-0BAE 1316-AG-00556-0VAE 1

247-030-05099-0BAE 1

013-7600-05766-1E 1

Foot 320-NBR-05214-0BAE 2

010-0N25-05265-EAmplifier 1

Screw for woofer

Insulation foam 328-000-05855-0WAE 2

Woofer 32PF55JZP-PW02-E 4

Gasket 398-ABS-05062-E 2

Gasket

214-000-05409-0BAE 4

214-000-05408-0BAE 4

Gasket

蔣國正


of 30

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

1

2

3

4

5

6

7

8

序號品名料號

1 Screw for amplifier 10

數量

2 Amplifier 1

4

3Logo

Wood Cabinet

1

1

Rubber Foot8 4

6

7

5

Screw for woofer

Woofer 1

5

1Logo fot grille

241-100-00613-2BCE

010-7610-05246-E

25PF12DZB-FW01-E

352-AM04020D210-E

316-AL-00553-E

316-AG-00557-E

352-FM04020D605-E

320-RUB-00057-0BAE

作業指示版本日期

2009/12/03 0

頁次

1

客戶:

機種:

初版發行0

ISSUE REVISIONS

表單編號: 版

確認承認

DATE NAME

制作

蔣國正

2009/12/03

務注: 1.銘板(316-AL-00553-E)背後點3188膠水

再貼到鐵網卞槽中

2.銘板(316-AL-00553-E)的位置是:銘板下端距靠LED燈的箱體邊緣60mm,左右居中

1

2

3


of 30

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

BHenriks

Rectangle

Harman/Kardon SB15 Soundbar with wireless subwoofer. System Parts list.

SB15 CenterPart Number Part Description

013-7600-05766-1E Crossover352-AM03008C1086-E Screw for Crossover32DM20AX-HT03-E Tweeter315-ABS-05231-0BAE Bottom Panel305-ABS-05037-0BAE Side Cap247-030-05099-0BAE Rear Enclosure315-ABS-05230-0BAE Top Panel352-AM04008C1334-E Screw for woofer to rear enclosure013-7600-05766-E Crossover32PF55JZP-PW02-E Woofer316-AG-00556-0VAE LOGO320-NBR-05214-0BAE Rubber Foot010-0N25-05265-E Amplifier328-000-05855-0WAE Insulation foam243-030-05259-0BAE Baffle 329-030-05464-0BAE Grill

SB15 SubPart Number Part Description

352-AM04020D210-E Screw for Subwoofer010-7610-05246-E Amplifier SB15/230 SUB 241-100-00613-2BCE Wood Cabinet316-AG-00557-E Harman Kardon Logo for the Sub top board316-AL-00553-E Logo for grille25PF12DZB-FW01-E 10" Subwoofer352-FM04020D605-E Screw for woofer to wood cabinet320-RUB-00057-0BAE Rubber pad for subwoofer cabinet051-A05264D-E STANDBY POWER PCB ASSY SB15 SUB

051-A05264C-E WIRELESS PCB ASSY SB15 SUB 051-A05264B-E DIGITAL POWER AMP PCB SB15 SUB051-A05264A-E PREAMP PCB ASSY SB15 SUB302-FE-05275-0BAE Subwoofer Amplifier panel150-E0764201-E Transformer152-V60202603-E Power Cord154-V09006T0-E Fuse 155-520020-E Fuse holder162-50652003-E Speaker Wire180-P3024DB-E Power Rock Switch306-ABS-05082-0BAE Rear Enclosure323-AL-05184-0LAE Aluminum heat sink335-NYL-00002-0BAE Power Cord Strain Relief311-ABS-00028-0BAE Knob

Accessories and packagePart Number Part Description

151-E1105301-E Power adapter165-020001101-E Signal cable for Ext. Trigger input jack376-000-01249-0BAE L brackets (2pcs) Accessory bag for Soundbar 403-000-05796-E Accessory box for Soundbar 435-000-05196-E Protective boards for Soundbar


of 30

431-000-07021-E EPE for Soundbar carton end430-002-05391-E Pearl-cotton bag for Soundbar431-000-07026-E EPE for Soundbar mid-carton402-000-06333-E Gift Box for Soundbar Cntr406-000-06124-E Owner Manual431-000-07022-E EPE Material for Subwoofer (top)283-001-05105-0WAE Non-woven cloth bag424-000-00185-E PO bag431-000-07023-E EPE Material for Subwoofer (bottom)398-000-00304-E Drier402-000-06334-E Gift Box for SB15 Sub/230


of 30

1

1

2

2

3

3

4

4

D D

C C

B B

A A

VSS

VCC

SGND

VSS

VCC

SGND

SGND

22KR01

22KR08

220PC02

18.7kR06

15.4k

R0417.8kR02

33nC04

24.9K

R05

100pC03

220kR09

VCC 10k

R07

VSS

220pC05

12

345

6sw1

SW2-2

10KR03

10KR10

mout

84

75

6

2

U2BTL072CN

100n

C06

VCC

VSS

10uC01

8.25kR21

+12VC

100uC11

IN 3

2

OUT1

GND

U5MC78L12CP

VCC

3.3kR18

VCC

VSS

VCC

VSS

100uC21

4.7uC23

SGNDSGND

SGND

SGND

VCC

VSSSGND

220pC29

4.7uC34

100nC35

100nC25

4.7uC36

4.7uC26

100uC32

4.7uC37

4.7uC28

100nC13

100nC12

220nC38

100nC08

22nC27

47kR23

24.9kR19

22kR22

14.3kR20

VCC

VSS

SGND

100nC15

82.5kR15

12.1KR11

OUT

Netsw1_36.8k

R1710uC16

220nC18

10uC17

V+ 1

OUTa 2INa3

INT4

Vref5

SENCE6

SW 7

INb8 OUTb 9

GND 10

U4

NJM2761-104.7uC22

VR2AVR*2

VR2BVR*2

A50kVR1

12345

CON2

Header 5

SGND

OUT

8

1

4

3

2

1

U2ATL072CN

8

1

4

3

2

1

U3ATL072CN

84

75

6

2

U3BTL072CN

mout

100nC09

VCC

VSS

SGND

100nC30

82.5kR16

12.1KR12

2

31A

411

U1ATL074CD

SGND

VCC

VSS

5

67B

411

U1BTL074CD

10

98C

411

U1CTL074CD

12

1314D

411

U1DTL074CD

12345

CON1

Header 5VSS

VCC

SGND

CUSTOMER:JBLMODEL:SB 15SUB/230

DETA:SEP.01.2009

PREPAREDCHECKEDCHECKEDAPPROVED REV1.0

PAGE 2/5

BOARD: PERAMP


of 30

1

1

2

2

3

3

4

4

D D

C C

B B

A A

S/L1CLK INH15CLK2

SI10A11B12C13D14E3F

4 G5 H6

QH 9

QH7

VCC 16

GND8

U04

SN74HC165D

S/L1CLK INH15CLK2

SI10A11B12C13D14E3F

4 G5 H6

QH 9

QH7

VCC 16

GND8

U03

SN74HC165D

20KR08

20KR10

20KR12

20KR17

20KR19

20KR21

20KR23

20KR0720KR0920KR1120KR1420KR1620KR1820KR2020KR22

10KR24

GND GND

GNDGND

10KR15

GND100RR13

1000u/10VC02

100nC03

10nC04

1000u/10VC07

100nC05

10nC06

100nC15

100nC16

VCC

VCC

GND GND

4.7RR04

4.7RR01

GND

SCK23

AGND224

LRCK19

PI220

PC515

MCLK16

MSIO07

MOSI08

SCK09

Vcc4

/RST5

RFVcc1

AGND121

SDOUT22

AVdd25

PB1(CS0)6

RFGND2

GND3

PF1(ID_CLK)11

PC0(ID_LATCH)12

/PC1(MUTE_LED)13

PF0(ID_DATA)10

/PC4(BOND_LED)14

PC7(I2C_SDA)17

PI0(I2C_SCL)18

RX M1087MD1

Rx M1087

/RST 1

SDATA 2

SCLK/DEM1 3

LRCK 4

MCLK 5

DIF1 6

DIF07

DEM08

FILT+9 VQ

10REF_GND11AOUTR12AGND13AV14AOUTL15MUTEC16

U06

CS4340

AGND

4.7KR33

100nC32

100nC29

100nC21

1000u/10VC20

10kR42

10kR43

10kR28

10kR40

1nC23

1nC31 AGND

8

1

4

3

2

U05ANJM4560

3.9kR35

20kR27

150pC19

3.9kR41

20kR39

150pC27

84

75

6

U05BNJM4560

AGND

AGND

AGND

AGND

GND

470u/16VC13

100nC14

VCC

VCCVCC

VCC

AGND

33RR36

VCC

33RR25

470u/16VC18

100nC17

AGND

VCC1

VCC1

GND

AGND

12

3

45

SW1

SEL

GND

1 2 3 4 5 6 7 8

CON1Header 8

100nC01

GND

47kR03

VCC

GND

100RR29

100RR30

100RR31

100RR32

AGND

link1

GND

1 2BD2

BD

12BD1

BD D01SCD14

100RR44100RR45

nRESET 2

Vss

1V

cc3

U02STM809

510R47

Q028050S

Q038050S

Q018050S

510R48

20kR49

47kR50

47kR51

123

CON2

Header 3

link1

link1

VCC

12

CON4

Header 2

47kR52

Q048550S

0.22uC22

10uC30

10uC28

10uC25

10u

C26

33RR37

470u/16VC33

100nC24

12345

CON3

Header 5

AGND AGND

VSS

VSS

VSS

openC34

openC35

openC36

openC37

openC38

openC39

GND

openC40

openC41 GND

GNDGND


DETA:SEP.01.2009


PAGE 3/5

BOARD: WIRLESSGND

rest

rest


of 30

1

1

2

2

3

3

4

4

5

5

6

6

7

7

8

8

D D

C C

B B

A A

6800u/35vC24

22u/35vC40 DZ2

6800u/35vC43

100/2W

R08Q02D882

100/2W

R22

22u/35vC36

22nC38

22nC42

Q04B772

220u/25v

C30

220u/25vC44

VCC

VSS

+15v

-15v

1 12 23 3CON4

-15v

+15v

VCC

VSS

IN1+8

IN2+5

IN2-4

VD

DA

110

OSC

7

MO

DE

6

VD

DP1

14V

DD

P223

BOOT1 15

OUT1 16

BOOT2 22

VSS

P117

OUT2 21

IN1-9

VD

DA

23

VSS

D24

STA

BI

18

VSS

P220

VSS

A1

12V

SSA

21

PRO

T13

N.C

.19

SGND111

SGND22

U1

TDA892XBTH

L02

33uH

L01

33uH

MO

DE

VDDA2 VSSA2 VDDP VSSP

VDDP VSSPVSSP

VDDP VSSP

VDDP VSSP

47u/100v

C11

470u/35vC01

470u/35vC03

SUB

VDDA2 VSSA2

VDDA2 VSSA2

220u/25VC09

10KR04 5.6V

DZ1

D011N4148

470u/35vC08

470uC02

VDDP

VCC

VSSP

VSS

30.1kR05

24kR03

MODE

100nC12

100nC17 100n

C16

100n

C19100n

C15

100n

C18

100n

C50

100n

C57100nC56 100n

C51

100n

C52

100n

C58

1uC26

1uC20

1nC23

1nC25

220pC53

470pC60

470pC59

470pC13

470pC14

15n

C39

15n

C27

100nC07

100nC06

100nC05

100nC04

2.2uC10

5.6kR14

5.6kR10

0RR21

30.1KR06

10RR19

10RR07

10R

R02

10R

R01

4.7KR11

4.7KR20

680R

R12

680R

R18

1.3KR15

15KR09

15KR16

123456

CON1

Header 6

+3.6V

std 12345

CON2

Header 5

+15v

-15v

SUB

12BD1

BD

12BD2

BD

Q068550S

VCC

BR1Bridge1

100nC34

100nC21

1nC22

100nC31

100nC54

100nC48

100nC35

100nC41

Q038050S

SGN

D

SGND

VSSA2

C45120n/63V

C28120n/63V

R1722R

R1322R

12

CON3

CON2

SUBOUT+

SUBOUT-

C29470n/63V

C49470n/63V

330pC32

330pC46

12BD6

BD

12BD4

BD

100nC55

6.8nC61

100nC33

6.8nC62

330pC63

R232R2

R242R2

330pC64

2.2nC65

2.2nC66

D021N4148


DETA:SEP.01.2009


PAGE 4/5

BOARD: POWER AMP


of 30

1

1

2

2

3

3

4

4

D D

C C

B B

A A

0.22uC07

12

34

L028mH

RV114D471K

TRANSFORMER

10nC16

0RR18

GND

4.7kR13

D011N4007

D041N4007

D031N4007

D061N4007

15uf/400VC01

470PF/1kC08

OB1

VCC2

GND3

CT4 FB 5

IS 6

OC 7

OC 8U02

THX203H

47uF/16VC13

680PC15

1

2

4

3

op1

PC817C

4.42KR08

10kR14

510R07

0.1uC17

10kR09

10kR06

21

3

U01ST TL431

330pFC03

300kR02

1.1megR03

1.1megR04

2RR12

0.1u/25VC12

D05UF1010

22nC18

100KR05

HI VOL

ICSP

GND

GND

std

2RR11

300kR01

680RR17

100k

R10

0RR15

D07SF16

std

+3.6V

12

CON3Header 2B

12

CON2Header 2B

+12VB

Q028050S

470u/16VC04

22uH

L1

Inductor

470u/16VC05

D02UF302

GND

+3.6V

0.1uC09

0.1uC11

D081N4148

123

CON1Header 3

K1Relay-SPST

GND

N_IN

L_OU

T

L_IN

0RR21

GND

AK

LED1

GND0R

R16Q038050S

Q018050S

HI OPERATIVE

LOW OPERATIVE

OPEN:R05,Q01,R13,R18

OPEN:R15,R16

+12VB

+3.6VA

2

34

5

1

W1

W2

W3

6

7

W4

S1S2

6

8

TR1

TR

D09UF302

100u/25VC06

0.1uC10

GND

+3.6VA

1000pC19

1000pC20

GND


DETA:SEP.01.2009


PAGE 5/5

BOARD: STANDBY POWER

68 ohmR19

openR20

openR22

100kR23

GND

+12VA


of 30


of 30

HarmanKardon SB15 230 Actsub

Documents

Transcript of HarmanKardon SB15 230 Actsub