HANOVER ARCHITECTURAL PRODUCTS VERTICAL WALL … · quality concrete products for over 40 years,...
Transcript of HANOVER ARCHITECTURAL PRODUCTS VERTICAL WALL … · quality concrete products for over 40 years,...
1
HANOVER® ARCHITECTURAL PRODUCTS
VERTICAL WALL APPLICATIONS
2Hanover® Architectural Products
has been manufacturing high
quality concrete products for
over 40 years, participating in
the development of unit paver
systems as they became an
integral part of architectural
design. Hanover’s extensive
knowledge acquired
through the development of
unit pavers has been applied
to vertical wall units. From
Reconstructed Stone™ Masonry
units for building facades to
Chapel Stone® Garden Wall units
used to create seat walls and
pillars, Hanover® can provide a
range of products for vertical
wall applications – commercial
and residential alike.
6
3
28
11
24
VERTICAL WALLAPPLICATIONS
CONTENTS
RECONSTRUCTED STONE™
RockCurb®
Reconstructed Stone™ Masonry
Reconstructed Stone™ Wall Panels
Sills, Profile Returns and Watertables
Custom & Profile Cutting
Strengths & Test Results
GARDEN & LANDSCAPE WALLS
Ammon’s® Wall
Chapel Stone® Garden Walling
Chapel Stone® Radius Pieces
Pillar Cap
Step Block
Chapel Stone® Pavers
4-2161114182021
22-35242830313232
Stone, the first building material,
has long been treasured for its
architectural representation.
Unfortunately, cost and
availability limit the use of natural
stone. During the manufacturing
process, Hanover® applies
a million pounds of pressure
to each unit, fusing the stones
together. This unique process
ensures a product which is
stronger and more durable
than a cast or lightweight
product. Hanover’s test results
show high compressive
strength, density and low water
absorption qualities. Using
cement as a binder, each
product truly becomes
Reconstructed Stone™.
Winners, Bayonne, NJ; Size & Color: 3 5/8” x 23 5/8”, 7 5/8” x 23 5/8”, 11 5/8” x 23 5/8”, #M1428; Finish: Tudor®
RECONSTRUCTED STONE™ ROCKCURB®
Straight Sections
Radius Sections
Transition Sections
Roof Applications
Colors & Installation Guidelines
RECONSTRUCTED STONE™ WALL UNITS
Reconstructed Stone™ Masonry
Keystones
Masonry Colors
Reconstructed Stone™ Wall Panels
Wall Panel Colors
Sills, Profile Returns and Watertables
Custom & Profile Cutting
Strengths & Test Results
6-10
6
7
8
9
10
11-21
11
13
13
14
16
18
20
21
SECTION 1 :RECONSTRUCTEDSTONE™
6
SIZES:
THICKNESS:
STOCKEDCOLOR:
ROCKCURB® PROFILES:
Installed alone or with Radius
or Transition sections, Hanover’s
Straight sections are the most
widely used type of RockCurb®.
RockCurb® Straight sections
are 36” long and 6” thick with a
12” or 18” height. Both heights
are available in both the Battered
and Bullnose Profiles.
RockCurb® units are consistent
in size and many times more
durable than poured in
place curbing. These high density
concrete units are manufactured
to 1/8” tolerances simplifying the
installation. An 1/8” joint is
recommended to allow
expansion through freeze-thaw
cycles. RockCurb® can be easily
reconfigured and reinstalled to
accommodate changes or repairs.
12" x 36" or 18" x 36"
6”
Limestone GrayCustom color and aggregate blending are available on special order when quantities permit.
15º angle
12”H
18”H 18”H
12”H8”H
ROCKCURB® STRAIGHT SECTIONS
Monument Park, Virginia Beach, VA; Owner: Association of Naval, Virginia Beach, VA; Architect: Cox, Kliewer & Company, PC; Size & Color: Battered RockCurb®, 12” x 36” x 6”, Limestone Gray; Finish: Tudor®
RECONSTRUCTED STONE™ | ROCKCURB® STRAIGHT SECTIONS
Estuary at Lincoln Harbor, Weehawken, NJ; Developer: Roseland Property; Landscape Architect: Marchetto Higgins Stieve; Size & Color: 23 7/8” x 23 7/8”, 12” x 36” x 6” Battered RockCurb®, Cream, #M1929, #M1704; Finish: Tudor®, #13
7
RockCurb® Radius Sections can
be used when the installation
incorporates curves. Gentle arches
or circles can be accommodated
by using a combination of radii
and straight sections. A complete
selection of radii are available
creating endless landscape and
streetscape design possibilities.
Manufactured with either a 12”
or 18” height, RockCurb® Radius
Sections are available in two
edges. The 18” RockCurb® Radius
Section is available in both the
angled Battered Profile and the
rounded Bullnose Profile. The
12” section is available in the
Battered Profile only and a
limited number of external radii.
Custom aggregate blending is
available when quantities permit.
Greensboro Center City Park, Greensboro, SC; Architect of Record: J. Hyatt Hammond Associates; Landscape Architect: Halvorson Design Partnership; Owner/Client: Action Greensboro, Inc.; Size & Color: Bullnose RockCurb® Radius, Various Sizes, #M1764; Finish: Tudor®
RADIUS TYPE
EXTERNAL
3’ 5’
x
6’ 8’ 10’
x
15’
x
20’
x
30’
x
The 18” section is available in the Battered and Bullnose Profiles.
The 12” section is available in the Battered Profile only and a limited number of external radii.
RADIUS TYPE
EXTERNAL
INTERNAL
3’
x
5’ 6’
x
x
8’
x
10’
x
15’
x
x
20’
x
x
30’
x
x
12” ROCKCURB® RADIUS SECTION LENGTH
18” ROCKCURB® RADIUS SECTION LENGTH
A2 + B2
2B= Radius
InternalRadius
External Radius
Road
StraightSection
B
A
Radius
ROCKCURB® RADIUS SECTIONS
DETERMINATION OF RADIUS:
RECONSTRUCTED STONE™ | ROCKCURB® RADIUS SECTIONS
Corporate Office Building; Landscape Architect: Roofmeadow; Size & Color: Bullnose RockCurb®, Various Sizes, #M3049; Finish: Tudor®
8
To allow the transition from a full
height curb to the appropriate
level needed for an entrance
or drive, 3 special shapes are
manufactured. The Left and Right
Transition Sections reduce the
height, while the Center Transition
Section provides the opening.
Center Transitions can be used
in multiples to allow any size
driveway width. Straight or Radius
Sections can be easily removed
and replaced with Transition
Sections to permit the transition to
the level of the Center Transition
Section.
Transition Sections are produced
with the angled Battered Profile.
Custom colors and aggregate
blends can be ordered when
quantities permit.
Large & Above Photos: LPS Pavement Corporate Headquarters, Oswego, IL; Design/Builder: LPS Pavement; Size & Color: RockCurb® 12” x 36” x 6”, Antietam; Finish: Tudor®
Decorative Paving, Franklin, OH; Design/Build: Decorative Paving Company; Size & Color: Battered RockCurb®, Various Sizes, Limestone Gray; Finish: Tudor®
12"
36"
6"
6"
8"
15º angle
Left TransitionSection
Center TransitionSection
Right TransitionSection
Straight Section
TRANSITION SECTIONS
ROCKCURB® RETURN ENDSTo eliminate miter cuts, Hanover® can provide RockCurb® Return Ends as part of a custom order. Return Ends are available with a Bullnose Profile only.
RECONSTRUCTED STONE™ | ROCKCURB® TRANSITION SECTIONS
9
Hanover® RockCurb® for roof
applications has become an
integral part of green building
projects, helping to earn SS
(Sustainable Sites) Credits
and achieve LEED (Leadership
in Energy and Environmental
Design) points. Working hand in
hand with green roof assemblies
to provide environmental benefits
and aesthetically appealing
rooftop gardens, RockCurb®
can be used to separate green
areas from hardscaped areas.
RockCurb® can be installed over
the waterproofing system based
on waterproof manufacturers
recommendations.
Hanover® can provide a range
of products that yield reflectance
and emittance values. These
values are a critical element in
the roof’s ability to reduce heat
consumption into the structure
below. RockCurb® can be used
with Prest® Pavers in Hanover’s
Glacier White color for maximum
values, helping to earn SS Credits
and achieve LEED points.
HANOVER® ROCKCURB® IS AN INTEGRAL PART OF ENERGY-EFFICIENT GREEN ROOF DESIGN.
Corporate Office Building; Landscape Architect: Roofmeadow; Size & Color: Bullnose RockCurb®, Various Sizes, #M3049; Finish: Tudor®
RECONSTRUCTED STONE™ | ROCKCURB® FOR ROOF APPLICATIONS
Pennsylvania State University School of Law, Lewis Katz Building, University Park, PA; Architect: Polshek Partnership Architects, New York, NY; Size & Color: 23 1/2” x 23 1/2” x 2”, RockCurb®, Glacier White; Finish: Tudor®
Wounded Warrior Sanctuary Hall, Bethesda, MD; Owner: Naval Support Activity Bethesda; Architect: Clark Nexsen; Size & Color: 11 3/4” x 23 1/2”,23 1/2” x 23 1/2”, 23 1/2” x 35 3/8”, RockCurb®, Tan, Charcoal; Finish: Tudor®
10
RockCurb® is stocked in Limestone Gray with a Tudor® finish but can be produced in any of the colors shown.
These blends were developed by Hanover’s efforts to respond to particular project requirements. Additional
custom blending is available on special order when quantities permit. Prest® Pavers and Prest® Brick are
also available in the same colors providing the opportunity to blend or contrast the curb with the project’s
hardscape or landscape.
The detail shown below is an example of a typical RockCurb® installation based on a unit paver to road surface
condition. Each project is unique and requires examination of the project requirements. Base preparation,
edge restraint and their specifications are important and must be given consideration. An architect, landscape
architect and/or structural engineer should be consulted to develop a specification for the individual project
Matrix #115 Matrix #1171
Matrix #1119 Matrix #1151 Matrix #1856
Limestone Gray- Stocked
Yellow Charcoal Matrix #1458Natural Matrix #1064
Glacier White
Setting Bed
Hanover® Unit Paver
Sub-Base
Compacted Subgrade
Concrete Cradle
Granular Basedepth of base as specified
Elevation Support
Hanover® RockCurb®
12” Battered Profile shown
Bituminous Roadway
HANOVER® ROCKCURB®
RECONSTRUCTED STONE™ | ROCKCURB® COLORS WITH TUDOR® FINISH
RECONSTRUCTED STONE™ | ROCKCURB® INSTALLATION GUIDELINES
11
Reconstructed Stone™ Masonry is
made from high density concrete
for vertical applications. Available
in a variety of sizes and a range
of thicknesses, they are normally
installed with mortar as walls
or included with other building
material as an accent band.
They provide a natural
appearance to the building
facade. Test results of the
products show relative strengths
comparative to natural stone
with high compressive strengths,
extreme density, and low water
absorption. The units can be
cleaned as necessary with
masonry acidic cleaners and can
be installed above or below grade.
Reconstructed Stone™ Masonry
units are made 3 5/8” thick and
are available in five sizes as
shown to the right.
*This size is also available in a 35 5/8” length.
15 5/8” x 23 5/8” x 3 5/8”LH D
11 5/8” x 23 5/8” x 3 5/8”*H L D
7 5/8” x 23 5/8” x 3 5/8”H L D
L D
3 5/8” x 23 5/8” x 3 5/8”H
MASONRY UNITS
Large and Right Photos: Winners, Bayonne, NJ; Size & Color: 3 5/8” x 23 5/8”, 7 5/8” x 23 5/8”, 11 5/8” x 23 5/8”, #M1428; Finish: Tudor®
RECONSTRUCTED STONE™ | MASONRY
Herring Run Professional Center, Seaford, DE; Builder/Developer: Gillis Gilkerson Inc., Salisbury, MD; Size & Color: 7 5/8” x 23 5/8” x 3 5/8”, Sill Profile D, Watertable Profile D, #M1983; Finish: Tudor®
12
Above Photos: Vineland Fire Company #1, Vineland, NJ; Size & Color: 7 5/8” x 23 5/8” x 3 5/8”, 15 5/8” x 23 5/8” x 3 5/8”, #M1767; Finish: Tudor®
• Walls
• Accent Banding
• Window and Door Details
• Architectural Entrances
• Keystones
Above and Right Photos: Office Building, Durham, NC; Architect: Little and Associates; Size & Color: 3 5/8” x 23 5/8” x 3 5/8”, 23 1/2” x 35 7/8” x 2”, 24” x 36” x 2”; #M1930, #M115; Finish: Tudor®
Right Photo:Harvard Graduate Student Housing, Cambridge, MA; Architecture and Urban Design: MACHADO AND SILVETTI ASSOCIATES, INC., Boston, MA; Size & Color: 3 5/8” x 23 5/8”, 7 5/8” x 23 5/8”, #M1983; Finish: Cloth, Tudor® Photograph © Michael Moran
RECONSTRUCTED STONE™ | MASONRY
13
Bottom Middle Photo: Herring Run Professional Center, Seaford, DE; Builder/Developer: Gillis Gilkerson Inc., Salisbury, MD; Size & Color: 7 5/8” x 23 5/8” x 3 5/8”, Sill Profile D, Watertable Profile D, #M1983; Finish: Tudor®
12 1/4” Height 10 3/8” Height
HANOVER® KEYSTONES
Reconstructed Stone™ Keystones
are manufactured in the two
heights shown and two colors,
Glacier White and a beige tone
color. Glacier White is shown
above. Contact Hanover® for
more information.
Matrix #115 Matrix #1636 Matrix #1983 Matrix #2088 Matrix #2049 Matrix #1428 Matrix #2115 Matrix #2156
Matrix #1930 Matrix #1719
The colors shown were developed by Hanover’s efforts to respond to particular project requirements. Hanover’s
Tudor® finish is a specialized texture designed to reveal the aggregates naturally, giving the surface of the
masonry unit a granite-like appearance.
Left and Top Middle Photos: Madison FIre & Police, Madison, NJ; Owner: Borough of Madison, NJ; Architect: HMR Architects; Size & Color: Various Sizes, #M1428; Finish: Ground
RECONSTRUCTED STONE™ | MASONRY COLORS WITH TUDOR® FINISH
RECONSTRUCTED STONE™ | MASONRY
14
Hanover’s line of wall panels
bridges the gap between
concrete and natural stone.
Unique manufacturing methods
truly reconstruct stone pieces into
beautiful building panels. A wide
range of sizes and thicknesses
are available. The units can be
prepared with either slots or
grooves which will accommodate
many styles of anchoring or
clip systems. Hanover® can also
provide custom aggregate
blending services in order to meet
the needs of any project. Colors
are shown on pages 16 and 17.
2"
2"
1"
7/8"
1/4"
7/16"9/16"
Caulkor
Mortar
Napoleon Dental Associates, Napoleon, OH; Architect of Record: Beilharz Architects, Inc., Defiance, OH; Size & Color: 23 7/8” x 23 7/8” x 2 1/2”, 23 7/8” x 23 7/8” x 2”, 11 15/16” x 11 15/16” x 2”, 23 7/8” x 23 7/8” x 3”, Quarry Red, Natural; Finish: Tudor®
HANOVER® WALL PANELS
RECONSTRUCTED STONE™ | WALL PANELS
Large and Right Photos: Vanderbilt University Recreation & Wellness Center, Nashville,TN; Owner: Vanderbilt University; Architect: Moody Nolan; Size & Color: 23 5/8” x 35 5/8” x 6”, #M3468; Finish: Ground, Stipple, Heavy Tudor®
15
All Photos: Office Building, Durham, NC; Architect: Little and Associates, Durham, NC; Size & Color: 3 5/8” x 23 5/8” x 3 5/8”, 23 1/2” x 35 7/8” x 2”, 24” x 36” x 2”; #M1930, #M115; Finish: Tudor®
11 3/4" x 11 3/4"
11 15/16" x 11 15/16"
14 7/8" x 14 7/8"
11 3/4" x 17 5/8"
11 3/4" x 23 1/2"
17 5/8" x 17 5/8"
17 5/8" x 23 1/2"
23 1/2” x 23 1/2”
23 3/4” x 23 3/4”
23 7/8” x 23 7/8”
23 1/2” x 29 1/2”
23 1/2” x 35 3/8”
29 3/4” x 29 3/4”
35 3/4” x 35 3/4” *
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
HANOVER® MEETS FEDERAL METRIC CONSTRUCTION GUIDELINES.
RECONSTRUCTED STONE™ | WALL PANELS
= Standard Thickness 2” Thickness = 25 lbs/sf *Note increased thickness and weight for this panel.
ACTUAL SIZEWALL PANEL SIZES
1 1/2" 2" 3" 4"2 1/4” 2 1/2”
16
The eight standard colors shown are available in a wide range of sizes and thicknesses. Custom color
blending can be accommodated, as well as custom aggregate blending. Hanover’s Tudor® finish is a specialized
texture which reveals the aggregates naturally giving the surface a stone-like appearance. It is a surface equally
suited to urban and municipal projects.
Texture is as important to the appearance of the installation as color and pattern. Hanover’s Ground Finish
provides a smooth surface revealing the aggregates beneath. Custom color and aggregate blending is
available when quantities permit.
Hanover® Wall Panels are also produced in a Tudor®
#13 finish which gives a delicate sandstone-like texture.
A few available colors are shown to the right.
Other custom colors can be ordered when
quantities permit.
Super Black Matrix #1111 Matrix #1171 Matrix #1049 Matrix #1185 Matrix #1109 Matrix #1151 Matrix #1240
Quarry Red Charcoal Natural Red 15 Tan Brown Cream LimestoneGray
Matrix #1428 Matrix #1775 Matrix #2127 Matrix #1914
RECONSTRUCTED STONE™ | WALL PANEL STANDARD COLORS WITH TUDOR® FINISH
RECONSTRUCTED STONE™ | WALL PANEL CUSTOM COLORS WITH GROUND FINISH
RECONSTRUCTED STONE™ | WALL PANEL CUSTOM COLORS WITH TUDOR® #13 FINISH
17
The colors shown below were developed by Hanover’s efforts to respond to particular project requirements.
Hanover ’s Tudor® finish is a specialized texture designed to reveal the aggregates naturally, giving the surface
of the wall panel a granite-like appearance.
PLEASE NOTE: Additional custom blending is available on special order when quantities permit. The color photos shown in this catalog
were prepared with great concern for accuracy. However, it is suggested that actual samples be requested before specifying. Due to the
natural variance of the raw materials used, panels can be expected to differ slightly from sample to actual product. It is recommended that
the panels be cleaned after the installation is finished. Please contact our representatives for product suggestions.
Matrix #1458 Matrix #1025 Matrix #115 Matrix #1171* Antietam* Matrix #1119
Matrix #1914 Matrix #1916* Matrix #1952 Matrix #1457 Matrix #1856 Matrix #1875*
Matrix #1767 Matrix #1442 Matrix #1111* Matrix #1256 Matrix #1636 Matrix #1983
Matrix #1428 Matrix #2115 Matrix #2156 Matrix #1930 Matrix #1537 Matrix #2659
Matrix #1151* Glacier White
Matrix #1810 Matrix #1649
Matrix #2088 Matrix #2922
Matrix #2259 Matrix #2835
* Colors are available with a Heavy Tudor®, Ground or Ground Tudor® finish only.
RECONSTRUCTED STONE™ | WALL PANEL CUSTOM COLORS WITH TUDOR® FINISH
18
Hanover® is able to provide profiled
edges for window details and
sills. They can be accommodated
with or without a continuous drip
edge. Pieces are manufactured
with beautiful natural finishes and
will add attractive detailing to
any project. Several styles and
custom designs are available
when quantities permit.
The sill profiles that Hanover®
is able to provide are shown
above right. The drawings have
a length of 23 5/8" and 35 5/8".
The 35 5/8" length is available
in heights of 3 5/8" to 5 5/8".
Custom heights and lengths
are available.
Sill Profiles H and C with Drip Edge
• Sills shown have a length of
23 5/8" with a height of 3 5/8".
• Sills with a length of 35 5/8"
are available in heights
ranging from 3 5/8" - 5 5/8".
• Range of depths
• Optional Drip Edge
• Same colors as
Reconstructed Stone™
Masonry and Wall Panels.
• Profile Returns create
seamless corners and
eliminate miter cutting.
S-F
4 5/8” - 11 5/8”
S-H
3 5/8” - 11 5/8”
S-I
5” - 11 5/8”
S-J
6 7/8” - 11 5/8”
S-G
4” - 11 5/8”
S-B
3 5/8” - 11 5/8”
S-A
3 5/8” - 11 5/8”
S-C
3 5/8” - 11 5/8”
S-D
3 5/8” - 11 5/8”
S-E
3 5/8” - 11 5/8”
Sill Profiles H and C with Drip Edge
Sill Profile F
RECONSTRUCTED STONE™ SILL PROFILES
RECONSTRUCTED STONE™ | SILLS
19
Hanover® Architectural Products
is pleased to announce the
addition of Profi le Returns to its
Reconstructed Stone™ Masonry
product line. The addition of Profi le
Returns eliminates miter cutting
corner pieces. Available in a
variety of sizes and a range of
thicknesses, they are available
in the same colors as Hanover’s
Masonry and Wall Panel units.
Watertable Profile D
• Watertables shown have
a length of 23 5/8” with
a depth of 3 5/8”.
• Lengths of 35 5/8” are
available in depths ranging
from 3 5/8” to 5 5/8”.
• Range of heights
WT-I
WT-EWT-D
3 5/8”to
11 5/8”
WT-G
4”to
11 5/8”
WT-H
3 5/8”to
11 5/8”
5”to
11 5/8”
WT-J
6 7/8”to
11 5/8”
3 5/8”to
11 5/8”
WT-F
4 5/8”to
11 5/8”
PLEASE NOTE: Units can be cleaned, as necessary, with masonry acidic cleaners and can be installed above or below grade.
Shown to the right are the
watertable profiles that Hanover®
is able to provide. The drawings
have a length of 23 5/8” and
35 5/8”. The 35 5/8” length is
available in depths of 3 5/8” to
5 5/8”. Available in the same
colors as Masonry and Wall
Panels, custom heights and
lengths are available.
PROFILE RETURNProfile Return matches Sill Profile A
RECONSTRUCTED STONE™ | PROFILE RETURNS
RECONSTRUCTED STONE™ | WATERTABLES
RECONSTRUCTED STONE™ WATERTABLE PROFILES
20
To truly finish the effect of a project,
masonry details at windows,
doorways, arches and cornices
can make an incredible difference.
Installations become very
distinctive and unique. Hanover®
can produce sections using the
same aggregates and colors
as the Reconstructed Stone™
Masonry or custom manufacture
accenting pieces on special
order. Profiles can be created from
Hanover® designs or customer
drawings. Technical assistance is
available to develop the shapes
required for the project.
Hanover® can prepare intricate
sections for building details.
Many designs are available
and custom profiles can also
be accommodated. Contact
a Hanover® representative for
technical details and a complete
listing of designs.
Sill
KeystoneSegmentalHeader
QuoinCorner
Semi Circular Header
• Maximum section size is
23 5/8” x 35 5/8”.
• Maximum depth is 7 5/8”.
RECONSTRUCTED STONE™ | CUSTOM AND PROFILE CUTTING
21
PLEASE NOTE: Unique manufacturing methods provide relative strengths comparative to natural stone. Some mix designs may test lower than shown above due to softer aggregates used for custom blending.
Hanover® Reconstructed Stone™ Masonry and Wall Panels are manufactured by unique methods which
duplicate the qualities of natural stone. Hanover® applies over a million pounds of pressure to each unit, fusing
the aggregates and stones together. This unique process ensures a panel which is stronger and many times
more durable than a cast or lightweight product. Hanover’s test results show high compressive strength, density,
and low water absorption qualities comparable to natural stone.
This test measures the minimum compressive
strength of Hanover’s products. The products are
tested in accordance with the standards set forth
by ASTM C936 which reference the use of test
procedure C 140. Panels are subjected to pressure
and monitored until the point of failure.
Density is the mass per unit volume of a substance
at a specified pressure and temperature.
Products are tested in a supportive condition with a
load applied to the mid-span between support. The
load distribution is calculated in relationship to the
product size and thickness. The products are subject
to continual pressure until the point of failure. The
result is the modules of rupture.
Hanover’s products are manufactured not to differ by more than plus or minus 1/8” in depth and 1/16” in
length and/or height.
Products are immersed in water for 24 hours and
then removed and weighed. The products are dried
for no less than 24 hours in a ventilated oven and
weighed again. The resulting difference yields the
percent of absorption.
RESULTSMinimum Compressive Strength =
8,000 psi average
10,000 to 12,000 psi, depending on aggregate used
RESULTSDensity = 150 lbs/ft3
RESULTSModules of Rupture = 1,100 (ASTM C936)
RESULTSAverage % Absorption = 5% maximum (ASTM C936)
RECONSTRUCTED STONE™ | MASONRY & WALL PANEL STRENGTHS & TEST RESULTS
MINIMUM COMPRESSIVE STRENGTH
ABSORPTION OF WATER
DENSITY
MODULES OF RUPTURE
DIMENSIONAL TOLERANCES
Hanover® manufactures two
styles of garden and landscape
walls – Chapel Stone® Garden
Walling and Ammon’s Wall®. Both
styles of walls add beauty, charm
and value to your landscaping.
Chapel Stone® Garden Walling
and Ammon’s Wall® are great
alternatives to natural stone.
Manufactured from high density
concrete to obtain compressive
strengths equal to natural stone,
Hanover’s walls have low water
absorption to ensure a long
lasting installation.
Hanover’s Garden and
Landscape Walls offer the
versatility to create anything
from planter walls and seat walls
to free standing walls and pillars.
Hanover’s walls are produced in
a range of colors to complement
or contrast Hanover’s other
paving products.
Chapel Stone® Garden Walling, 9” Deep, Various Lengths, 3” & 6” Heights, Gray Blend; Chapel Stone® Wall Caps, Gray Blend
AMMON’S WALL®
Ammon’s Wall®
Stocked Colors & Packaging Information
Installation Guidelines
CHAPEL STONE®
Chapel Stone® Garden Walling
Chapel Stone® Radius
Pillar Cap
Step Block
Chapel Stone® Paver
Standard Colors & Packaging Information
Garden Walling Installation Guidelines
24-27
24
26
27
28-34
28
30
31
32
32
33
34
SECTION 2 :GARDEN & LANDSCAPE WALLS
24
AMMON’S WALL®
8” x 12” x 4”
Ammon’s Wall®, Salmon/Charcoal Blend
Ammon’s Wall®, Gettysburg Gray
Ammon’s Wall®, Chocolate/Tan Blend
AMMON’S WALL® Sized at 8” x 12” x 4”, Ammon’s
Wall® is a very versatile wall
block. Blocks can be laid in any
direction to create a natural
random pattern. Building patterns
are endless creating a unique
wall with every installation.
Ammon’s Wall® can be used to
create decorative pillars, steps,
and garden or planter walls.
Lights can easily be added on
top of pillars or columns built
with Ammon’s Wall® as voids are
created in the center of the pillar
allowing electrical cords to be
protected and hidden from view.
Produced and textured to capture
the look and durability of natural
stone, Ammon’s Wall® is available
in four earth-toned color blends
as shown on page 26. With only
one size block, installation is quick
and easy. When building an 8” or
12” wall, the block can also be
used as a cap.
GARDEN & LANDSCAPE WALLS | AMMON’S WALL®
Ammon’s Wall®, South Mountain Sand
25
Ammon’s Wall® Radius, Gettysburg Gray
Ammon’s Wall® Radius, South Mountain Sand
AMMON’S WALL® MIXED
AMMON’S WALL® RADIUS
Ammon’s Wall® Mixed, South Mountain Sand
Right Photo: Ammon’s Wall® Mixed, South Mountain Sand
AMMON’S WALL® MIXEDAmmon’s Wall® Mixed consists of
3 sizes - 8” x 12”, 8” x 8” and
4” x 8” with a 4” depth. All
sizes are installed together to
create a more natural, random
appearance. Blocks can be laid
in any direction. Ammon’s Wall®
Mixed units can be used alone
or combined with the additional
8” x 12” x 4” Ammon’s Wall® units.
AMMON’S WALL® RADIUSSized at 8” x 12, Ammon’s Wall®
Radius is a wedge shaped unit
designed to allow the wall to
bend and curve with the
landscaping and architecture
while maintaining closer joints
between units. Garden Walls often
need curves and bends as they
work around trees and planting
beds. Gentle arcs and radii can
be more easily be achieved with
these radius units. Ammon’s Wall®
Radius units can be used alone
or combined with the original
Ammon’s Wall® units.
GARDEN & LANDSCAPE WALLS | AMMON’S WALL®
26
Ammon’s Wall®, Ammon’s Wall® Radius and Ammon’s Wall® Mixed are stocked in the four earth-toned color
blends shown below. Custom colors are available upon special order and when quantities permit.
PLEASE NOTE: Hanover’s blended colors consist of several shades and will include some solid and some blended pieces.
GARDEN & LANDSCAPE WALLS | AMMON’S WALL® STOCKED COLORS
Gettysburg Gray Salmon/Charcoal BlendChocolate/Tan Blend South Mountain Sand
GARDEN & LANDSCAPE WALLS | AMMON’S WALL® SIZE & PACKAGING INFORMATION
PLEASE NOTE: Ammon’s Wall® is sold by the full cube only.
*For Ammon’s Wall® only:
21.3 face feet/cube is based on creating a 12” solid wall and 32 face feet/cube is based on creating an 8” solid wall.
Use the formula shown on page 27 to determine the number of pieces needed before ordering.
UNIT SIZEUNIT SIZE FACE FT./CUBE PCS./FACE FT. PCS./CUBE PCS./STRAP LBS./CUBE
8” x 12” x 4”
8” x 12” x 4”
8” x 12” x 4”8” x 8” x 4”4” x 8” x 4”
Ammon’s Wall®
Ammon’s Wall® Radius
Ammon’s Wall® Mixed
32 (8”) - 21.3 (12”)*
30
32 (8”)
3 (8”) - 4.5 (12”)
–
–
96
108
144
24
–
–
2892.48
2735
2850
27GARDEN & LANDSCAPE WALLS | AMMON’S WALL® INSTALLATION GUIDELINES
Existing Undisturbed Subgrade
Hanover® Edge 300
Finish Grade
3/4" - 1” Sand Setting Bed (ASTM-C-33)
Hanover® Prest® Brick
Adhere Ammon’s Wall® at every course with Concrete Adhesive.Apply 1/4” bead in “S” shape.
Ammon’s Wall®
Adhere with Concrete Adhesive. A wall with a 12” depth is shown. Use two Ammon’s Wall® units turned in the opposite directions to create a cap with overhang.
4" Compacted Base (2 A Modified or similar)
or Concrete Footer. Place on level surface
Existing Undisturbed Subgrade
Hanover® Edge 300
Finish Grade
4" Compacted Base (2 A Modified or similar)
or Concrete Footer. Place on level surface
3/4" - 1” Sand Setting Bed (ASTM-C-33)
Hanover® Prest® Brick
Adhere Ammon’s Wall® at every course with Concrete Adhesive.Apply 1/4” bead in “S” shape.
Ammon’s Wall®
Adhere with Concrete Adhesive. A wall with an 8” depth is shown. Use one Ammon’s Wall® unit turned in the opposite direction to create a cap with overhang.
AMMON’S WALL® INSTALLATION | 8” DEPTH
AMMON’S WALL® INSTALLATION | 12” DEPTH
Please Note for Ammon’s Wall® only : Ammon’s Wall® is sold by the full cube only. 21.3 face feet/cube (4.5 pcs/face ft.) is based on creating a 12” solid wall. 32 face feet/cube (3 pcs/face ft.) is based on creating an 8” solid wall.
Contact Hanover® for product quantity and Installation Guidelines for Ammon’s Wall® Radius and Ammon’s Wall® Mixed.
PLEASE NOTE: When constructing seat walls, columns or free standing walls, be sure to adhere each course with a concrete adhesive. When constructing a low garden wall, bonding is not necessary but is suggested.
Assuming normal conditions, maximum wall height for Ammon’s Wall® with a 12” depth when used as a garden wall is 36”. Maximum wall height for Ammon’s Wall® with an 8” depth is 28 - 32”.
1. Determine the length( L ), height( H ) and depth of your
wall. Will you be constructing a wall with a depth 8” or 12” ?
2. Calculate wall materials needed.
For an 8” wall :
_____ (L) x _____ (H) = _____ x 3 = _____ pcs. needed
For an 12” wall :
_____ (L) x _____ (H) = _____ x 4.5 = _____ pcs. needed
3. Prepare the footing. Dig a trench 16” wide and 3” - 6”
below grade. The height of the wall will determine the
number of units to bury. As a rule of thumb, you will bury
1” of block for every 8” of exposed wall height. Add 4” for
the depth of the base material. Make sure the soil is well
compacted to prevent settling.
4. Construct the base. A level compacted base is
crucial for wall stability. Consisting of 2 A modified stone
or concrete footer, the base should be 4” deep with 8”
behind and 8” in front of the wall.
4. Install the base course. Position the units side by side
on prepared base. Along the back of the block, level
the units with a carpenter’s level from front to back and
side to side. Use a string line to verify straightness.
5. Install additional courses. Attempt to offset joints
of units for maximum design strength. Ammon’s
Wall® should be installed in a random pattern. When
constructing seat walls, columns or free standing walls,
be sure to adhere each course with a concrete
adhesive. When constructing a low garden wall,
bonding is not necessary but is suggested. Shims
may be occasionally needed for leveling blocks.
Assuming normal conditions, maximum wall height
for Ammon’s Wall® with a 12” depth when used as a
garden wall is 36”. Maximum wall height for Ammon’s
Wall® with an 8” depth is 28 - 32”. Higher elevations
require engineering design. Certain conditions might
reduce the maximum wall height such as soil that does
not drain well, a slope behind the wall or a nearby
structure. To complete the installation, adhere the top
course with concrete adhesive.
28
Above and Right Photos: Chapel Stone® Garden Walling, 9” Deep, Various Lengths, 3” & 6” Heights, Canyon Blend; Chapel Stone® Wall Caps, Canyon Blend
Chapel Stone® Garden Walling, 9” Deep, Various Lengths, 6” Height, NEW Russet Blend
Chapel Stone® Garden Walling
is a versatile and interesting
addition to our paving product
lines. It is available in four naturally
blended colors – Gray Blend,
Tan Blend, Canyon Blend and
Russet Blend. Garden Walling is
manufactured in random lengths
and two heights – 2 13/16” and
5 5/8”. Colors and heights can
be used separately or mixed
together. The natural stone
characteristics of the walling
lend it to a large variety of uses
— surrounding a patio, raising
a flower bed, creating a low
retaining wall, or building steps,
walkways and paths. Walling
can add so much to the
landscaping theme. It adds detail
and interest to the project, as
well as, plant and bedding areas.
The entire landscape seems to
come together!
Each stone has been faced (or
textured) with half of the pieces
faced on both sides. The double
faced pieces can be used for free
standing walls or installed mixed
with those without facing for a
natural effect. Though not all units
are textured on both sides, it can
be requested as part of a custom
order. Three of the four lengths
also have return ends for corners.
Because the pieces are consistent
in shape, they will lay neatly
creating dimensional stability
and saving installation time. Both
homeowners and professional
masons will appreciate the ease
of wall construction.
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® GARDEN WALLING
Chapel Stone® Garden Walling, 9” Deep, Various Lengths, 3” & 6” Heights, Tan Blend; Chapel Stone® Wall Caps, Tan Blend; ; Chapel Stone® Pillar Caps, Sand
29
Chapel Stone® Garden
Walling can be laid as a dry
wall with no mortar or as a
mortared wall with mortar joints.
If a mortared system is used, weep
holes along the bottom of the
wall are required. Chapel Stone®
Garden Walling can be laid up
to 3 feet high. Elevations beyond
3 feet require engineering design.
Chapel Stone® is not meant as
a highway retaining wall. Both
systems require a crushed stone
backing between walling and
soil. See pages 34 and 35 for
installation guidelines. Chapel
Stone® Garden Walling may be
cleaned with masonry cleaners
as necessary.
Right Photo: Chapel Stone® Garden Walling, 9” Deep, Various Lengths, 3” & 6” Heights, Tan Blend; Chapel Stone® Wall Caps, Tan Blend
Chapel Stone® Wall Caps,
complete the installation. Sized
at 11 3/4” x 11 3/4” x 3”, they are
produced in the same blends
as Garden Walling – Gray, Tan,
Canyon and Russet Blends.
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® GARDEN WALLING
CHAPEL STONE® WALL CAPS
Above and Top Left Photos: Chapel Stone® Garden Walling, 9” Deep, Various Lengths, 6” Heights, Gray Blend; Chapel Stone® Wall Caps, Gray Blend
30
Chapel Stone® Radius pieces
allow the walling to blend and
curve with the landscaping and
architecture. Gentle arcs can be
accomplished without the radius
pieces, however, a tighter joint
can be maintained using these
wedge shaped stones.
Radius pieces are available
in four colors - Gray Blend,
Tan Blend, Canyon Blend and
Russet Blend. Two heights,
2 13/16” and 5 5/8”, are available.
Each height is packaged
separately with a random mix of
the four angled shapes.
Chapel Stone® Radius is shown with
a 6” height in Tan Blend. A 3” height
and other colors are available.
Heights and colors are packaged
separately with a random mix of
the four angled shapes.
18” Radius 12” Radius
6” Radius 6” Radius
Chapel Stone® Garden Walling Radius, 9” Deep, Various Lengths, 3” Height, Canyon Blend; Chapel Stone® Wall Caps, Canyon Blend
Chapel Stone® Garden Walling Radius, 9” Deep, Various Lengths, 3” & 6” Heights, Gray Blend
Chapel Stone® Garden Walling Radius, 9” Deep, Various Lengths, 3” Height, Tan Blend; Chapel Stone® Wall Caps, Tan Blend
Chapel Stone® Garden Walling Radius, 9” Deep, Various Lengths, 6” Height, Tan Blend
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® RADIUS
CHAPEL STONE® RADIUS
31
Above Photo: Chapel Stone® Garden Walling, 9” Deep, Various Lengths, 3” & 6” Heights, Canyon Blend; Chapel Stone® Wall Caps, Canyon Blend
Left Photo: Chapel Stone® Garden Walling, 9” Deep, Various Lengths, 3” Height, Gray Blend; Chapel Stone® Pillar Cap, Gray
Large and Top Left Photos: Chapel Stone® Garden Walling, 9” Deep, Various Lengths, 3” Height, Gray Blend; Chapel Stone® Pillar Cap, Sand
Sized at 30” x 30” x 2 1/2”, Chapel
Stone® Pillar Caps are available
for use with Chapel Stone®
Garden Wall. They are prefect for
use on top of columns, as stair
treads or outdoor table tops. Pillar
Caps can be used alone or in
conjunction with Hanover’s other
Wall Caps.
They are available in three
colors - Chocolate, Gray and
Sand. All three colors compliment
Hanover’s Chapel Stone® Garden
Walls. The Pillar Cap can also be
special ordered in a 3” thickness
when quantities permit.
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® PILLAR CAPS
CHAPEL STONE®
PILLAR CAPS
32
Please Note: Although Chapel Stone® Pavers offer an undulant, irregular top surface to the pavement, these pavers do not meet ADA requirements.
Chapel Stone® Step Block, Chocolate, Gray and Sand
Hanover’s Chapel Stone® Step
have a pitched face with a
SlateFace top surface for a
more natural appearance. They
are produced in three colors -
Chocolate, Gray and Sand - to
compliment Hanover’s extensive
line of paving products. Available
with lengths of 24” and 36”,
steps are 6” high with an
18” depth.
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® STEP BLOCK
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® PAVERS
CHAPEL STONE®
STEP BLOCK
CHAPEL STONE® PAVERSHanover's Chapel Stone® Pavers
create a bold stone paving
design. With uneven and rocky
top surfaces, they are perfect
for the project that requires a
more rugged appearance. With
the vertical edges being true in
size, the product can be installed
quickly and economically without
the use of mortar.
Sized at 6" x 12" x 4", Chapel
Stone® Pavers are available in
the same Gray and Tan Blends
as Garden Walling. Custom
blending is available for a variety
of applications.
Woodland Park Crossing, Herndon, VA; Architect: MV+A Architects; Landscape Architect: Landscape Architecture Bureau, LLC, Washington, DC; Size & Color: Chapel Stone® Pavers, Gray and Tan Blends
33
PLEASE NOTE: Garden Walling is packaged with randomly sized lengths (6”, 12” , 18” and 24”). Each height and color blend is packaged separately. Pieces are made with return ends for corners on 6”, 12”, and 18” lengths. This product is for garden walls and should be limited to 3’ in height. Refer to pages 32 & 33 for installation guidelines.
Hanover® Chapel Stone® Garden Walling is stocked in the four color blends shown below. Custom colors
and aggregates are available upon special order and when quantities permit. Chapel Stone® lengths are
mixed within a cube to ensure a natural looking, random installation. Each color and height is cubed separately.
Garden Walling can be installed using either height or mixing the two together.
SoilSoil
Drainage Stone
Exposed Edge
6”12”18”24”
6”12”18”
HEIGHT
HEIGHT
HEIGHTLENGTH
LENGTH
LENGTHDEPTH
DEPTH
DEPTH
2 13/16”
5 5/8” 24” 18”
2 13/16”
5 5/8”
5 5/8” 36” 18”
5 5/8”
9” 9”
30 sf/cube
3100 lbs/cube
420 sf/truck
14 cubes/truck
96 sf/cube
3450 lbs/cube
1248 sf/truck
13 cubes/truck
30 sf/cube
2925 lbs/cube
450 sf/truck
15 cubes/truck
10 pcs/cube6.25 sf/unit62.5 sf/cube
27.2 lbs/sf1700 lbs/cube
11 3/4” x 11 3/4” x 3”
29 3/4” x 29 3/4” x 2 1/2”
GARDEN WALLING SIZES
STEP BLOCK SIZES
WALL CAP SIZE
PILLAR CAP SIZE
RADIUS SIZESPACKAGING INFORMATION
PACKAGING INFORMATION
PACKAGING INFORMATION
PACKAGING INFORMATION
PACKAGING INFORMATION
21 sf/cube 1350 lbs/cube
31.5 sf/cube 2042 lbs/cube
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® GARDEN WALL STOCKED COLORS
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® STANDARD SIZE & PACKAGING
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® RADIUS INSTALLATION GUIDELINES
PLEASE NOTE: Hanover’s blended colors consist of several shades and will include some solid and some blended pieces.
Tan Gray Russet BlendGray Blend Canyon Blend
Chapel Stone® Radius pieces are
used to create arcs and curves
within a wall design. Radius
pieces can be used in several
ways by turning them over. Follow
the installation guidelines shown
on page 34 for Chapel Stone®
Garden Walling.
34
4"
3' H
eig
ht
Fin
ish
Gra
de
to
Fi
nis
h G
rad
e
Wall CapAdhere with Concrete Adhesive.
Geogrid Soil Reinforcement (Min. LTDS = 900 PLF Min.)MIRAFI MARAGRID 2 XT EXTEND, see notes.
Adhere Geogrid to Chapel Stone® with Concrete Adhesive.
Adhere Chapel Stone® at every coursewith Concrete Adhesive.Apply a 1/4” bead in an “S” shape
Finish Grade
4" Compacted Base 2 A Modified (or similar)or Concrete Footer. Place on level surface.
25"
9"8" 8"4" Dia. Perforated PVC Drain TileSlope and extend to suitable drain location.
Reinforced BackfillExtend min. 6” past Geogrid. See notes for properties.
Finish GradeFinished grade should dissect first course.
8"
min
.
Woven Filter FabricWrap around backfill.
3'
2' 6
"
6"min.
1" Setback at each course
GEOGRID SOIL REINFORCEMENT NOTES:1. Pull Geogrid taut and anchor prior to backfi ll placement over Geogrid.2. Geogrid reinforcement shall be continuous throughout the embedment length.100% coverage shall be provided at each level.3. Geogrid extends min. 8” over the Chapel Stone® and shall be bonded to the stone.4. Apply adhesive to both sides of Geogrid to insure proper bond to both courses.
REINFORCED BACKFILL NOTES:1. Use ballast stone (min. 1 1/2” diameter) for backfi ll, or structural fi ll as per the geotechnical report prepared by specialized engineering, fi le no. 063503, dated Oct. 18, 2006.2. Place reinforced backfi ll in 12” lifts.3. Compact reinforced backfi ll to 95% of maximum dry density as determined by modifi ed proctor tests, ASTM D-1557.4. Tracked compaction equipment shall not be used directly on Geogrid reinforcement. A min. thickness of 12” of reinforced backfi ll is required above Geogrid to utilize tracked compaction equipment.5. Only small vibratory hand operated rollers or walk behind rollers or equipment shall be allowed within 5’ of the wall.
PLEASE NOTE: Proper installation methods must be followed to ensure wall strength and stability. Freestanding walls should not exceed 3 feet in height. Retaining walls and walls with elevations beyond 3 feet must also employ proper installation methods and may require engineering design. Chapel Stone® Garden Walls can be laid as dry walls or as mortared walls. Chapel Stone® is not meant as a highway retaining wall.
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® GARDEN WALL INSTALLATION GUIDELINES
Calculate wall materials needed. Determine the square footage of the wall by multiplying length by the height.
Prepare the footing. Dig a trench 25” wide and 3 - 6” below grade. The height of the wall will determine the number of units to bury. As a rule of thumb, you will bury 1” of block for every 8” of exposed wall height. Add 4” for the depth of the base material. Be sure the soil is well compacted to prevent settling. Be sure disturbed soils are stabilized.
Construct the base. A level compacted base is crucial for wall stability. Consisting of 2 A modified stone or concrete footer, the base should be 4” deep with 8” behind and 8” in front of the wall. Total base width would be 16” plus the 9” depth of the wall unit for a total of 25”.
Install the base course. Position the units side by side on the prepared compacted base. Along the back of the block, level the units with a carpenter’s level from front to back and side to side. Use a string line to verify straightness.
Each course should be set back 1” from the front of the previous course and adhered with manufacturer recommended concrete adhesive. If using a concrete footer as the base, adhere the first course to the footer. Apply 1/4” bead of adhesive in an “S” shape for maximum strength. Care should be taken to insure that the adhesive is not exposed at the joints.
As the next course and all additional courses are placed, be sure to stagger the joints. Joints between wall units on adjacent courses should not align. Each unit should span two below.
Backfill the wall as you go. The wall should be backfilled using clean washed ballast stone (minimum 1 1/2” in diameter). The depth of the backfill should be equal to the height of the wall and wrapped on the top, back and bottom with woven filter fabric.
Stabilize wall sections as you go. The use of GeoGrid reinforcement to stabilize wall sections is recommended. GeoGrid should be adhered to the wall units between courses starting 12” from the base/foundation and continuing every 12”. Be sure top layer of GeoGrid is covered by a minimum of 12” of backfill stone.
1.
2.
3.
4.
5.
6.
35
Chapel Stone®
Step Block
Finish Grade
3/4" - 1” Sand Setting Bed (ASTM-C-33)
Hanover® Prest® Brick
Hanover® Edge 300
4" Compacted Base (3/4" to fines)
Existing Undisturbed Subgrade
Concrete Adhesive
Chapel Stone®
Garden Wall
Finish Grade
3/4" - 1” Sand Setting Bed (ASTM-C-33)
Hanover® Prest® Brick
Hanover® Edge 300
4" Compacted Base (3/4" to fines)
Existing Undisturbed Subgrade
Concrete Adhesive
Overlap the corners to create a bond. Using the corner
pieces provided, overlap the units to build your corner.
Be sure to stagger the joints; Joints between blocks on
adjacent courses should not align. Each block should
span two blocks below.
*A variety of Hanover® products such as Chapel Stone® Wall Caps or Appian® 6” x 9” brick can be incorporated into the step construction. They should be bonded to the Garden Walling units which are beneath them using a concrete adhesive. Be sure to allow cure time for the units to stabilize.
STEP BLOCK STEP CONSTRUCTION GARDEN WALLING STEP CONSTRUCTION*
GARDEN WALLING 90º CORNER
PLEASE NOTE: Chapel Stone® Garden Walling requires a stable footing,
compacted base and proper drainage with filter fabric. Please see
Page 34 Installation Guidelines or contact a Hanover® representative
for more information.
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® STEP CONSTRUCTION
Stair width, length and rise should be determined prior to beginning.
Compact existing subgrade if area has been excavated. Be sure disturbed soils are stabilized. Place compacted gravel
over compacted subgrade. Screed setting bedding sand.
Begin installation at bottom by installing the first step or course. Install the next layer of compacted gravel base behind
the first step. Install the second step. Use a Concrete Adhesive to adhere the second step to the first. Keep proper tread
depth in mind when setting this course. Continue this procedure for the desired number of steps or courses.
Adhere Step Blocks at each course or step. Concrete Adhesive should be applied in a 1/4” bead to the full length of the
block in an “S” shape. Care should be taken to insure that the adhesive is not exposed at the joint.
1.
2.
3.
4.
GARDEN & LANDSCAPE WALLS | CHAPEL STONE® 90º CORNER CONSTRUCTION
VERT-2016
5000 Hanover Road, Hanover, PA 17331 717.637.0500 • fax 717.637.7145
www.hanoverpavers.com
Cover Photo: Vanderbilt University Recreation & Wellness Center, Nashville,TN; Owner: Vanderbilt University; Architect: Moody Nolan; Size & Color: 23 5/8” x 35 5/8” x 6”, #M3468; Finish: Ground, Stipple, Heavy Tudor®
PRODUCT INSTALLATION : Each project and site conditions are unique. It is important to contact a Hanover® representative for product details and installation guidelines. An architect, landscape architect, and/or structural engineer should be consulted to develop a specification suited for the individual project. • Neither this catalog, nor any of the individual product catalogs from Hanover® Architectural Products, is intended to be a design manual. The projects pictured and the installation suggestions given in this catalog are only illustrations of Hanover® products. Each application and specification for installation should have the attention of an architect, landscape architect, and/or structural engineer. • As product use and site conditions are not within our control, Hanover® does not guarantee results from use of such products or other information herein: no warranty, express or implied is given. As government regulations and use conditions may change, it is the Buyers responsibility to determine the appropriateness of these products for the specific end uses.
PLEASE NOTE : The color photos shown in this catalog were prepared with great concern for accuracy. However, it is suggested that actual samples be requested before specifying. Due to the natural variance of the raw materials used, products can be expected to differ slightly from sample to actual product. It is recommended that the products be cleaned after the installation is finished. Please contact our representatives for product suggestions.
Hanover® Architectural Products reserves the right to modify, alter or discontinue the texture, color, content, shape or size of its products or any product line at any time for any reason.
CONTACT US for product details and information. We invite you to call us at 800-426-4242 to discuss your project, visit our web site www.hanoverpavers.com to download current catalogs and more detailed product information, or request our complete product brochures and samples.
©1971-2016 Hanover® Architectural Products
AMERICAN MADE
AMERICAN OWNED
Inside Cover PhotosEstuary at Lincoln Harbor, Weehawken, NJ; Developer: Roseland Property; Landscape Architect: Marchetto Higgins Stieve; Size & Color: 23 7/8” x 23 7/8”, 12” x 36” x 6” Battered RockCurb®, Cream, #M1929, #M1704; Finish: Tudor®, #13
Top Right Photo: Office Building, Durham, NC; Architect: Little and Associates; Size & Color: 3 5/8” x 23 5/8” x 3 5/8”, 23 1/2” x 35 7/8” x 2”, 24” x 36” x 2”; #M1930, #M115; Finish: Tudor®