GPS Adapter Bracket Installation...
Transcript of GPS Adapter Bracket Installation...
Page 1 AFG01 V.01 – Install Manual Mar 26, 2012 © 2012 The Attachment Farm Inc. All rights reserved.
GPS Adapter Bracket Installation Manual
GPS Adapter Bracket Installation Instructions:
Note that this bracket is only to be used as intended in this document any other uses of the product are solely at the risk of the end user. The Attachment Farm Inc. may be referred to as TAF.
First open box and ensure that you have all the pieces.
AFG01 package contents include: a. GPS Adapter bracket (AFG01) b. Lock Pin and clip c. Installation Manual
Customer Supplied components: a. Ratchet with 10 mm and 13mm socket b. On some cab installations an extension harness (PF80722) may be needed c. On some cab a cordless drill and assortment of drill bits may be needed
STEP 1
Test to ensure lock pin will fit thru holes in existing original Greenstar GPS bracket. If holes are too small drill out with electric cordless drill in small increments until you reach a 29/64” drill bit size. Remember to do this on both sides. ** Do NOT drill out straight to 29/64” as that only works in a drill press **
Photos shown from 9770 STS combine (7000 series tractor installs the same):
Page 2 AFG01 V.01 – Install Manual Mar 26, 2012 © 2012 The Attachment Farm Inc. All rights reserved.
GPS Adapter Bracket Installation Manual
STEP 2
With GPS receiver removed install AFG01 by sliding triple tab into slotted opening of original Greenstar bracket on cab. While pushing up on bracket slide pin thru Greenstar bracket as shown, locking AFG01 in place.
STEP 3
Install cutter pin to lock pin in place.
STEP 4
If it is too tight to push pin thru then drill out holes one size larger and repeat step 2
STEP 5
Install Starfire with Deluxe shroud. At any time change to Original Shroud by removing adapter.
Original Shroud Deluxe Shroud
(with AFG01 adapter bracket)
Check www.TheAttachmentFarm.com for the latest installation manuals.
Printed in Canada
Page 1 AFG02/AFG03 V.02 – Install Manual Mar 26, 2012 © 2012 The Attachment Farm Inc. All rights reserved.
GPS Combo Bracket Installation Manual
GPS Combo Bracket Installation Instructions:
Note that this bracket is only to be used as intended in this document any other uses of the product are solely at the risk of the end user. The Attachment Farm Inc. may be referred to as TAF.
First open box and ensure that you have all the pieces.
AFG02 package contents include: a. GPS Combo bracket (AFG02) b. Installation Manual
AFG03 Kit package contents include: a. GPS Combo bracket (AFG02) b. Adapter bracket for 30 series (AFP03) c. Adapter bracket for 00-20 series (AFP04) d. Two – M8x30mm flange head mounting bolts
(ONLY required for use with AFP4) e. Installation Manual
Customer Supplied components: a. Starfire GPS receiver b. Ratchet with 10 mm and 13mm socket
R Series Cab Install (8360RT shown) STEP 1
Remove 4 bolts from factory GPS receiver bracket as shown. **Be careful to hold the bracket(s) when removing the last bolt.
Factory Deere Original Shroud Factory Deere Deluxe Shroud
Page 2 AFG02/AFG03 V.02 – Install Manual Mar 26, 2012 © 2012 The Attachment Farm Inc. All rights reserved.
GPS Combo Bracket Installation Manual
STEP 2
Install the AFG02 bracket with 4 bolts removed in step 1 as shown. Try to keep bracket as square to bolt holes as possible.
STEP 3
Install complete, attach either Starfire ITC/ITC3000 with original shroud or deluxe shroud with ease. Route harness as shown.
STEP 4
Remove deluxe shroud by reaching under bracket and pull release lever to release latch.
Page 3 AFG02/AFG03 V.02 – Install Manual Mar 26, 2012 © 2012 The Attachment Farm Inc. All rights reserved.
GPS Combo Bracket Installation Manual
00, 10, 20 and 30 Series Tractors and sprayers. (9530 shown) STEP 1
Remove 3 bolts depending on series of factory GPS receiver bracket as shown below. **Be careful to hold the 2 piece bracket when removing the last bolt
Factory Deere Deluxe Shroud Factor Deere Original Shroud
STEP 2
Reinstall bottom bolt on front of cab leaving 1/4” of thread showing.
AFP03 adapter bracket for 30 series cabs AFP04 adapter bracket for 00, 10 and 20 Series cabs
Slide the adapter bracket (shown) onto the bolt, adjust in slot to enable top portion of bracket to match the surface of the cab and hand tighten the bolt.
Page 4 AFG02/AFG03 V.02 – Install Manual Mar 26, 2012 © 2012 The Attachment Farm Inc. All rights reserved.
GPS Combo Bracket Installation Manual
STEP 3
Now install AFG02 bracket with remaining 2 bolts removed in step 1 (for 00, 10 & 20 series use included M8x30 bolts). Adjust brackets to align straight with front of cab then tighten all three bolts as shown.
STEP 4
Install either Starfire ITC/ITC3000 with original shroud or deluxe shroud.
STEP 5
Remove deluxe shroud by reaching under bracket and pull release lever to release latch.
Installation complete, enjoy!
Check www.TheAttachmentFarm.com for the latest installation manuals.
Printed in Canada