of 26

• date post

27-Apr-2015
• Category

Documents

• view

87

4

Embed Size (px)

description

Gear & Gear Design

Transcript of Gear Noise

GEAR NOISE AND VIBRATION A LITERATURE SURVEYMats kerblom mats.akerblom@volvo.com Volvo Construction Equipment Components AB SE631 85 Eskilstuna, Sweden

Abstract This paper is a survey of the literature on gear noise and vibration. It is divided into three parts, Transmission error, Dynamic models and Noise and vibration measurement. Transmission error (TE) is considered to be an important excitation mechanism for gear noise and vibration. The definition of transmission error is The difference between the actual position of the output gear and the position it would occupy if the gear drive were perfectly conjugate. Dynamic models of the system consisting of gears, shafts, bearings and gearbox casing are useful in order to understand and predict the dynamical behaviour of a gearbox. Noise and vibration measurement and signal analysis are important tools when experimentally investigating gear noise because gears create noise at specific frequencies, related to number of teeth and the rotational speed of the gear. Keywords: gear, noise, vibration, transmission error, dynamic models.

CONTENTS1 TRANSMISSION ERROR................................................................................................. 2 1.1 Introduction to transmission error.................................................................................... 2 1.2 Transmission error theory ................................................................................................ 2 1.3 Transmission error measurement..................................................................................... 5 1.4 Gear inspection using transmission error measurement .................................................. 7 1.5 Transmission error calculation......................................................................................... 8 1.6 Correlation between calculated TE, measured TE and measured noise and vibrations 10 1.7 Other noise and vibration measurements....................................................................... 14 1.8 Friction and bending moments as gear noise excitations............................................... 15 2 DYNAMIC MODELS....................................................................................................... 15 2.1 Introduction to dynamic models .................................................................................... 15 2.2 Lumped parameter dynamic models.............................................................................. 15 2.3 Dynamic models of complete gearboxes ....................................................................... 17 2.4 Experimental investigations........................................................................................... 18 2.5 Noise prediction models (equations) ............................................................................. 19 3 NOISE AND VIBRATION MEASUREMENT.............................................................. 20 3.1 Introduction to noise and vibration measurement.......................................................... 20 3.2 Gear noise measurement ................................................................................................ 20 3.3 Gear fault detection........................................................................................................ 21 4 CONCLUSIONS................................................................................................................ 21 REFERENCES ..................................................................................................................... 22

1

1 TRANSMISSION ERROR1.1 Introduction to transmission error The most frequently used type of gear profile is the involute. It is used for cylindrical spur and helical gears as well as for conical gears like beveloid, hypoid and spiral bevel gears. Some characteristics of involute (cylindrical) gears that have made them so common are: Uniform transmission of rotational motion, independent of small error in centre distance. The sum of the contact forces is constant and the direction of the total contact force always acts in the same direction. An involute gear can work together with mating gears with different number of teeth. Manufacturing is relatively easy and the same tools can be used to machine gears with different numbers of teeth. (Applies to hobs, shaper cutters, grinding worms, shaving cutters but not to profile tools like milling cutters and profile grinding wheels).

If the gears were perfectly rigid and no geometrical errors or modifications were present, the gears would transmit the rotational motion perfectly, which means that a constant speed at the input shaft would result in a constant speed at the output shaft. The assumption of no friction leads to that the gears would transmit the torque perfectly, which means that a constant torque at the input shaft would result in a constant torque at the output shaft. No force variations would exist and hence no vibrations and no sound (noise) could be created. Of course, in reality, there are geometrical errors, deflections and friction present, and accordingly, gears sometimes create noise to such an extent that it becomes a problem. 1.2 Transmission error theory Transmission error (TE) is considered to be an important excitation mechanism for gear noise and vibration. The definition of transmission error made by Welbourn [20] is The difference between the actual position of the output gear and the position it would occupy if the gear drive were perfectly conjugate. This may be expressed as angular displacement or as linear displacement at the pitch point. An example of a typical transmission error signal is shown in figure 1.1.

2

50

Pinon run out

Twice per tooth-pass error

Once per tooth-pass error

0 Gear run out -50

-100Total TE

-150Tooth to tooth TE

-200Figure 1.1 Example of typical transmission error signal and its components. The causes of transmission error are deflections, geometrical errors and geometrical modifications. Examples of deflections: Contact deformations (hertzian) in the gear mesh Gear teeth bending deflections Gear blank deflections Shaft deflections Bearing and gearbox casing flexibility Examples of geometrical errors: Involute alignment deviations Involute form deviations Lead deviations Lead form deviations Gear tooth bias Pitch errors Run-out Error in bearing position in the casing

3