Gazette 18-24 Dated 27 June 2018 - Tomax · 6/27/2018 · Applicant: INOV8 ACCESS PTY LTD 50 5% ....

Commonwealth of Australia Gazette

No. TC 18/24, Wednesday, 27 June 2018 Published by the Commonwealth of Australia

TARIFF CONCESSIONS

CONTENTS

TCO Applications ....................................................................................................... 2

TCO Applications Refused ........................................................................................ 6

TCOs Made.................................................................................................................. 7

Intention to Revoke TCOs not used in over 2 years ............................................. 11

By-Laws Made .......................................................................................................... 12

The Commonwealth of Australia Tariff Concessions Gazette (the Tariff Concessions Gazette) is free of charge on

the Department of Home Affairs internet site at: https://www.homeaffairs.gov.au/busi/domestic-manufacturers-and-importers

The Tariff Concessions Administration Section is located at 5 Constitution Ave Canberra City 2601 Contact details: General Email Inquiries:………………………………[email protected] General Inquiries: (02) 6229 3567 TAPIN help desk: (02) 6275 6534 Facsimile: (02) 6223 8180

Cat. No.

ISSN 0813-8389

©Commonwealth of Australia, 2018

https://www.homeaffairs.gov.au/busi/domestic-manufacturers-and-importers

2 TCO Applications Commonwealth of Australia Gazette

No TC 18/24, Wednesday, 27 Jun 2018

TCO Applications

CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269K(1) - APPLICATIONS MADE FOR TARIFF CONCESSION ORDERS

Applications have been lodged for Tariff Concession Orders for the goods described in the following TABLE.

Australian manufacturers who wish to contest the granting of a Tariff Concession Order for the goods described

are invited to lodge a submission in writing in an approved form. Submissions must be lodged within 50 days

of the date of publication of this Notice.

The operative date (Op.) and TC reference number follow the description of goods.

To assist local manufacturers, the use(s) to which the goods can be put follow the description of goods.

Objections to the making of TCO submission forms are available at

https://www.homeaffairs.gov.au/Forms/Documents/b444.pdf

Contact: Email [email protected]

THE TABLE

Description of Goods including the Schedule 4 Item Number

Customs Tariff Classification General Duty Rate

8424.49.00 SPRAYERS, CROP, self-propelled, ride-on, having BOTH of the

following:

(a) spraying boom length NOT less than 20 m;

(b) spray tank volume capacity greater than 4 000 L

Op. 30.05.18 - TC 1862197

Stated Use:

For spraying agricultural crops

Applicant: JOHN DEERE LIMITED

50

5%

8424.89.90 SPRINKLERS, WATER MIST, including BOTH of the following:

(a) infrared flame detectors;

(b) water mist spray nozzles

Op. 04.06.18 - TC 1863274

Stated Use:

For the detection of fires and deployment of water mist as a

fire suppressant in applications such as particle board presses,

gas turbines, industrial fryers, paint shops and engine test beds

Applicant: BORG MANUFACTURING PTY LTD

50

5%

8425.31.00 WINCHES, portable, electric, having ALL of the following:

(a) safe working load NOT greater than 300 kg;

(b) weight NOT greater than 20 kg;

(c) battery powered;

(d) remote control

Op. 05.06.18 - TC 1864381

Stated Use:

Portable rope winches for lifting people

Applicant: INOV8 ACCESS PTY LTD

50

5%

https://www.homeaffairs.gov.au/Forms/Documents/b444.pdf

mailto:[email protected]





8431.49.90 PARTS, EXCAVATOR REVOLVING SHOVEL FRAME, being centre gudgeon

assemblies, consisting of ALL of the following:

(a) centre gudgeon;

(b) screws;

(c) tie wire;

(d) locking key;

(e) shim;

(f) nuts;

(g) adjusting collar;

(h) plates;

(i) washers

Op. 29.05.18 - TC 1861025

Stated Use:

To hold excavator revolving shovel frames

Applicant: JOY GLOBAL AUSTRALIA PTY LTD

50

5%

8431.49.90 PARTS, RIM AND/OR WHEEL, being rim AND/OR wheel bases, having

BOTH of the following:

(a) width NOT less than 254 mm;

(b) diameter NOT less than 840 mm

Op. 08.06.18 - TC 18350654

Stated Use:

Wheel components for large loaders and graders

Applicant: RIMEX WHEEL PTY LTD

50

5%

8438.90.10 ROLLERS, CHOCOLATE REFINING, having BOTH of the following:

(a) length NOT less than 850 mm and NOT greater than

1 850 mm;

(b) diameter NOT less than 300 mm and NOT greater than 500 mm

Op. 07.06.18 - TC 1865171

Stated Use:

Parts of a chocolate refining machine which process mass

into refined chocolate

Applicant: MONDELEZ AUSTRALIA PTY LTD

50

5%

8467.29.00 POWERHEADS, battery operated

Op. 30.05.18 - TC 1861927

Stated Use:

Providing power to various detachable garden tools such as

brush cutters, hedge trimmers, sweepers, cultivators, blowers and

pruners

Applicant: STIHL PTY LTD

50

5%

8479.89.90 DRY CONCRETE INGREDIENTS BATCHING PLANT, programmable logic

controlled, having ALL of the following:

(a) maximum volume capacity NOT less than 100 cubic metres per

hour;

(b) hopper, with OR without hopper liners;

(c) conveyors;

(d) discharge chutes;

(e) moisture meters;

(f) vibrators;

(g) weigher AND batcher;

(h) control panel;

(i) truck loading station housing

Op. 29.05.18 - TC 1860934

Stated Use:

For the measurement and batching of dry concrete ingredients to

predetermined specifications for loading into concrete mixing

trucks

Applicant: BGC (AUSTRALIA) PTY LTD

50

5%





8501.10.00 MOTORS, DC, including ALL of the following:

(a) length NOT greater than 120 mm;

(b) rated voltage NOT greater than 42 V;

(c) planetary gearhead diameter NOT greater than 32 mm

Op. 30.05.18 - TC 1861923

Stated Use:

Welding equipment wire feed

Applicant: MAXON MOTOR AUSTRALIA PTY LTD

50

5%

8537.10.90 SYSTEM, EXPLOSION PROTECTIVE ALERT AND FIRE SUPPRESSION

ACTIVATION, programmable logic controlled, with or without

electric current isolators, consisting of BOTH of the following:

(a) control panel;

(b) explosion pressure, spark, flame AND temperature detection

sensors

Op. 04.06.18 - TC 1863271

Stated Use:

For the activation of explosion alert communication and fire

suppression systems in industries such as wood chip production

lines for the manufacture of particle boards


50

5%

8537.10.90 CONTROL PANELS, SPARK DETECTION AND SUPPRESSION

Op. 04.06.18 - TC 1863277

Stated Use:

Operation of spark detection and suppression systems for use in

industrial processes such as particle board manufacture


50

5%

8537.10.90 CONTROLLERS, BUILDING SWITCH, remotely controlled OR programmed,

having ALL of the following:

(a) maximum voltage NOT less than 24 V DC;

(b) maximum power consumption NOT greater than 2 W;

(c) internet connector;

(d) connection capacity NOT greater than 6 ports

Op. 04.06.18 - TC 1863463

Stated Use:

To remotely control building switches that have electrically

connected functions such as heating, cooling, energy usage

monitoring, lighting, blinds, shutters and room occupancy signs

Applicant: SCHNEIDER ELECTRIC (AUSTRALIA) PTY LTD

50

5%

8544.49.19 DETONATOR WIRE, duplex, electronic, copper clad ferromagnetic

steel, in reels AND/OR coils, including ALL of the following:

(a) polyurethane insulation;

(b) conductor diameter NOT greater than 0.62 mm;

(c) tensile strength of NOT less than 450 newtons;

(d) electrical resistance NOT greater than 300 ohms per

kilometre;

(e) wicking resistance between conductor AND insulation NOT

less than 3 bar

Op. 25.05.18 - TC 1860018

Stated Use:

As a communication link between detonators and electronic

blasting equipment

Applicant: ORICA AUSTRALIA PTY LTD

50

5%





8544.49.19 DETONATOR WIRE, duplex, electronic, copper clad ferromagnetic

steel, in reels AND/OR coils, including ALL of the following:

(a) conductor diameter NOT greater than 0.62 mm;

(b) polyurethane OR polypropylene insulation;

(c) tensile strength NOT less than 240 newtons;

(d) electrical resistance NOT greater than 300 ohms per

kilometre;

(e) wicking resistance between conductor AND insulation NOT

less than 8.5 bar

Op. 25.05.18 - TC 1860021

Stated Use:

As a communication link between detonators and electronic

blasting equipment

Applicant: ORICA AUSTRALIA PTY LTD

50

5%

8701.95.90 TRACTORS, SHUNTING, including BOTH of the following:

(a) tyres AND rail flanged wheels;

(b) remote control

Op. 08.06.18 - TC 1886609

Stated Use:

Shunting of railway rolling stock

Applicant: UNIQUE RAIL PTY LTD

50

5%

8705.10.00 CRANES, MOBILE, LATTICE BOOM, having ALL of the following:

(a) lifting capacity NOT greater than 750 000 kg at 7 m radius;

(b) hoist height NOT greater than 193 m;

(c) radius NOT greater than 136 m

Op. 24.05.18 - TC 1859512

Stated Use:

For mobile lifting of extremely heavy loads at extreme heights

Applicant: MAMMOET AUSTRALIA PTY LTD

50

5%

6 TCO Applications Refused Commonwealth of Australia Gazette


TCO Applications R efused

CUSTOMS ACT 1901

NOTICE PURSUANT TO SECTION 269R(1) - APPLICATIONS FOR TARIFF CONCESSION ORDERS REFUSED

Applications for Tariff Concession Orders for the goods described in the following TABLE have been refused.

THE TABLE


Customs Tariff Classification

7419.99.00 TAGS, PET, with OR without connecting rings

Op. 08.03.18 - TC 1828219

Reason for refusal:

Substitutable goods produced in Australia in the ordinary course

of business by Kevron Plastics Pty Ltd, Campbellfield, Vic

50


Op. 08.03.18 - TC 1828221

Reason for refusal:



50


Op. 08.03.18 - TC 1828224

Reason for refusal:



50

7 TCOs Made Commonwealth of Australia Gazette


TCOs M ade

CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269R(1) - TARIFF CONCESSION ORDERS MADE

Tariff Concession Orders have been made for the goods described in the following TABLE.

The operative date (Op.) and TC reference No. follow the description of goods. Local manufacturers of

substitutable goods may request the revocation of TCOs at any time.

THE TABLE



2918.99.00 ISOPROPYL (E,E)-(7S)-11-methoxy-3, 7, 11-trimethy-2, 4-

dodecadienoate

Op. 03.04.18 Dec. date 20.06.18 - TC 1837935

50

3923.90.00 TUBES, polypropylene, threaded, with OR without ANY of the

following:

(a) barcodes;

(b) caps;

(c) jackets whether OR not co-moulded;

(d) lid locks;

(e) racks;

(f) tube locks;

(g) twist locks

Op. 13.03.18 Dec. date 20.06.18 - TC 1829322

50

8414.51.00 EXHAUST FANS, wall OR window OR ceiling mounted, having ALL

of the following:

(a) rated voltage NOT greater than 250 VAC;

(b) air flow NOT less than 360 m3/h and NOT greater than

600 m3/h;

(c) impeller diameter NOT greater than 250 mm;

(d) power consumption NOT greater than 45 W

Op. 15.03.18 Dec. date 20.06.18 - TC 1830872

50

8415.81.00 AIR CONDITIONERS, MARINE, reverse cycle, having ALL of the

following:

(a) cooling capacity NOT less than 1.4kW;

(b) supply voltage NOT less than 200 V;

(c) sea water inlet

Op. 29.03.18 Dec. date 22.06.18 - TC 1836692

50

8418.69.00 COOLER, WAFER SANDWICH, spiral

Op. 23.03.18 Dec. date 22.06.18 - TC 1834692

50

8421.29.90 STRAINERS, OBLIQUE Y TYPE, brass, with OR without magnet

inserts, having BOTH of the following:

(a) working temperature NOT greater than 180 Degrees Celsius;

(b) working pressure not greater than 2 000 Kpa

Op. 16.03.18 Dec. date 21.06.18 - TC 1831424

50

8421.29.90 EFFLUENT FILTRATION SYSTEM, OIL AND/OR GAS WELL, whether OR not

assembled, including BOTH of the following:

(a) NOT less than one pot;

(b) interconnecting pipes,

with OR without ANY of the following:

(i) isolation AND bypass valves AND/OR bypass drain;

(ii) telescopic frame AND/OR hoist

Op. 22.03.18 Dec. date 20.06.18 - TC 1833904

50

8428.39.00 ROD CONVEYORS, including ANY of the following:

(a) drive units;

(b) gears AND/OR bearings;

(c) protection guides

Op. 26.03.18 Dec. date 22.06.18 - TC 1835366

50





8428.90.00 ASH HANDLING SYSTEM, RECOVERY BOILER AND/OR ECONOMISER,

including ALL of the following:

(a) ash hoppers;

(b) doors;

(c) rotary feeders;

(d) slide gate valves;

(e) drag chain conveyers;

(f) vertical chutes;

(g) expansion joints

Op. 22.03.18 Dec. date 20.06.18 - TC 1833917

50

8428.90.00 LINEAR ROBOTS, sheet layer, with OR without ANY of the following:

(a) suction arm;

(b) lifting mast;

(c) slot magazine;

(d) driving rail

Op. 27.03.18 Dec. date 20.06.18 - TC 1835372

50

8428.90.00 SORTING AND FEEDING AND POSITIONING LINE, PLASTIC CONTAINER AND

CAP, including ALL of the following:

(a) conveyor;

(b) hopper;

(c) elevator;

(d) feeder

Op. 04.04.18 Dec. date 20.06.18 - TC 1837956

50

8438.10.90 MIXERS, BATTER, having ALL of the following:

(a) batch capacity NOT less than 60 kg;

(b) holding tank NOT less than 200 L;

(c) gentle mixing turbine

Op. 23.03.18 Dec. date 21.06.18 - TC 1834688

50

8438.10.90 WAFER SHEET CONDITIONING MACHINES, with OR without an air

conditioning unit, having a wafer sheet capacity NOT less than

478 and NOT greater than 1 500

Op. 23.03.18 Dec. date 20.06.18 - TC 1834690

50

8467.29.00 GRINDERS, with OR without ANY of the following:

(a) safety guards OR safety covers;

(b) wrenches;

(c) side handles OR grips;

(d) lock nuts;

(e) inner flanges;

(f) depressed centre wheels;

(g) grinding discs OR wheels;

(h) carry cases;

(i) cutting flanges;

(j) grinding flanges;

(k) wireless interface units;

(l) collets AND nuts;

(m) collet cones;

(n) collet nuts

Op. 26.03.18 Dec. date 20.06.18 - TC 1834915

50

8467.29.00 SCREWDRIVERS, with OR without ANY one OR more of the following:

(a) side grips OR handles;

(b) nozzle modules;

(c) locator modules;

(d) bits;

(e) carry cases;

(f) belt hooks OR clips;

(g) nutsetters

Op. 28.03.18 Dec. date 21.06.18 - TC 1836263

50

8479.60.00 EVAPORATIVE AIR COOLER, TURBINE INLET, having BOTH of the

following:

(a) airflow exceeding 190 000 m3 per Hour;

(b) cooling capacity exceeding 1 100 Kw

Op. 28.03.18 Dec. date 21.06.18 - TC 1836255

50





8481.80.90 BALL VALVES, having ALL of the following:

(a) brass alloy body AND aperture;

(b) brass square cap;

(c) inlet AND outlet diameter NOT less than 15 mm and NOT

greater than 80 mm

Op. 16.03.18 Dec. date 20.06.18 - TC 1831420

50

8481.80.90 BALL VALVES, having ALL of the following:

(a) flanged;

(b) ductile iron body;

(c) full bore diameter NOT less than 25 mm and NOT greater

than 200 mm

Op. 19.03.18 Dec. date 20.06.18 - TC 1832202

50

8481.80.90 FLOW CONTROL VALVES, balancing, cast iron construction, having

ALL of the following:

(a) pressure rating NOT less than 1 600 KPa;

(b) valve body size NOT less than 50 mm and NOT greater

than 300 mm;

(c) pressure differential measurement test points

Op. 19.03.18 Dec. date 20.06.18 - TC 1832204

50

8504.40.90 INVERTERS, string, multiple phase, with OR without built-in AC

OR DC disconnector switch, having ALL of the following:

(a) frequency NOT greater than 60 Hz;

(b) maximum power point tracking systems NOT greater than 6;

(c) output current being ANY of the following:

(i) NOT less than 45 A and NOT greater than 50 A;

(ii) NOT less than 61 A and not greater than 77 A;

(iii) NOT less than 140 A and NOT greater than 145 A;

(d) wired AND/OR wireless communication interface

Op. 26.03.18 Dec. date 20.06.18 - TC 1835362

50

8504.40.90 CHARGE STATION, ELECTRIC MOTOR VEHICLE BATTERIES, output voltage

NOT less than 150 VDC and NOT greater than 920 VDC,

being EITHER of the following:

(a) car chargers having an operating temperature NOT less

than -35 degrees Celsius and NOT greater than 55 degrees

Celsius, including ALL of the following:

(i) module power NOT less than 110 kW and NOT greater

than 600 kW;

(ii) charge capability 400 V cars at 150 kW;

(iii) maximum DC output current per charge post NOT

exceeding 500 A;

(iv) input voltage NOT greater than 450 VAC;

(b) heavy vehicle chargers having an operating temperatures

NOT less than -35 degrees Celsius and NOT greater than 50

degrees Celsius with OR without automated 4-pole rooftop

connection INCLUDING ALL of the following:

(i) module power NOT less than 50 kW and NOT greater

than 600 kW;

(ii) output current, per 150kW module, NOT greater than

250 A;

(iii) input voltage NOT greater than 450 VAC;

Op. 29.03.18 Dec. date 22.06.18 - TC 1836821

50

8536.50.99 ISOLATOR SWITCHES, single OR multiple pole, rail mounting

support, having ALL of the following:

(a) operational voltage NOT greater than 250 VAC;

(b) current NOT greater than 80 A;

(c) conditional short-circuit current NOT greater than 10 kA

Op. 29.03.18 Dec. date 21.06.18 - TC 1837351

50

8537.10.90 CONTROL PANELS, CO-GENERATION BOILER,


(a) programmable logic controller;

(b) safety instrument system;

(c) human machine interface

Op. 22.03.18 Dec. date 20.06.18 - TC 1833907

50





8701.94.90 TRACTORS, AIRCRAFT PUSHBACK AND TOWING, engine power NOT less

than 75 kW AND not greater than 130 kW

Op. 06.04.18 Dec. date 20.06.18 - TC 1839240

50

9405.40.00 LIGHTS, FLOOD, non-ceramic with OR without ceramic bulb-holder

OR metal halide lamp OR high pressure sodium lamp, having ALL of

the following:

(a) aluminium housing;

(b) aluminium reflector;

(c) mounting bracket;

(d) toughened glass visor;

(e) ethylene propylene diene monomer rubber seal;

(f) NOT less than 1 000 W

Op. 22.03.18 Dec. date 21.06.18 - TC 1833914

50

11 Intention to Revoke TCOs not used in over 2 years Commonwealth of Australia Gazette


Intention to Revoke TC Os not used i n over 2 years

TARIFF CONCESSION ORDERS (TCOs) NOT USED IN THE PREVIOUS 2 YEARS

The Comptroller-General of Customs is satisfied that the TCOs listed in the table below are no longer required

because, in the 2 years preceding the day of this notice, they have not been quoted in an import declaration

to secure a concessional rate of duty.

From Thursday, 26 July 2018, it is intended to take action to revoke these Orders under subsection 269SD(1A)

of the Customs Act 1901. In accordance with subsection 269SG(2) of the Customs Act 1901, in transit provisions

shall apply. If revoked, the expected date of effect will be 26 July 2018.

Interested parties are invited to provide, by close of business, Wednesday 25 July 2018, written reasons why

an Order should NOT be revoked.

Please advise if any of the Orders listed below have been quoted on an import declaration.

If a request is made to retain an Order used for the granting of a Determination, please specify the

Determination and the linked Item number to enable mapping to the Order and its scope.

THE TABLE

______________________________________________________________________________________________________________

Tariff

Classification Description Concession Number

______________________________________________________________________________________________________________

8427.20.00 WORKS TRUCKS, ALUMINIUM FLUORIDE TRANSPORT AND HOPPER FILLING,

mobile, having BOTH of the following:

(a) articulated discharge augers;

(b) centrally positioned rear cameras

Op. 22.10.13 Dec. date 13.01.14 - TC 1335329

8428.39.00 CASE AND/OR CARTON SEPARATION AND HANDLING SYSTEM, whether OR

not assembled, programmable logic controlled, having ALL of the

following:

(a) conveyors, having BOTH of the following:

(i) plastic belts;

(ii) wheels,

(b) optical sensor AND measurer;

(c) case AND/OR carton orientation pusher arm

Op. 21.11.13 Dec. date 03.03.14 - TC 1338999

8428.90.00 LIVE POULTRY PROCESSING SYSTEM, programmable logic controlled,


(a) poultry stunners;

(b) hanging platforms;

(c) module washers;

(d) gas extraction emergency controls;

(e) crate handlers AND conveyors

Op. 11.10.13 Dec. date 29.01.14 - TC 1334128

8428.90.00 HANDLING SYSTEM, programmable logic controlled, including ALL of

the following:

(a) conveyors;

(b) pouch OR parcel transfer robotic arm;

(c) conveyor belts;

(d) tray stacking robotic arm;

(e) tray sorting turntables

Op. 04.11.13 Dec. date 30.01.14 - TC 1336803

8428.90.00 SURGE HOPPERS, COPPER PROCESSING SYSTEM, cylinder AND/OR cube

shaped, rubber lined

Op. 05.12.13 Dec. date 21.05.14 - TC 1340490

12 By-Laws Made Commonwealth of Australia Gazette


By-Laws M ade

CUSTOMS ACT 1901

CUSTOMS TARIFF ACT 1995

SCHEDULE 4

BY-LAW No. 1800128

I, Alison Neil, delegate of the Comptroller-General of Customs, under section 271 of the Customs Act 1901

make the by-law set out in the Schedule below.

THE SCHEDULE

BY-LAW No. 1800128

Item 56

Schedule 4

1. This by-law may be cited as Customs By-law No. 1800128.

2. This by-law commences on 1 July 2018.

3. For the purposes of subparagraph (a)(i) of item 56 of Schedule 4 to the Customs Tariff Act 1995 (the

Customs Tariff Act), the following requirements are prescribed:

i. the kits do not indicate whether their contents are medicaments or placebos; and

ii. the kits do not contain goods other than:

a. the medicaments and/or placebos, whether or not in syringes or other delivery

mechanisms;

b. any item or packaging which is necessary for the safe transport and/or storage of the

goods;

c. any associated and necessary documentation and forms.

4. For the purposes of subparagraph 3(i), identifiers, regardless of their form, that cannot be deciphered

without additional information or equipment, do not indicate whether the contents of the kit are

medicaments or placebos.

5. For the purpose of this by-law “placebo” means a good not containing an active agent under study,

administered to some participants to compare the effects of the active agent to other participants.

6. For the purpose of this by-law, the “Customs Tariff Act 1995” means the Customs Tariff Act 1995, as

amended or proposed to be altered.

Dated this 5th day of June 2018.

Alison Neil

Delegate of the

Comptroller-General of Customs

Gazette 18-24 Dated 27 June 2018 - Tomax · 6/27/2018 · Applicant: INOV8 ACCESS PTY LTD 50 5% ....

Documents

Transcript of Gazette 18-24 Dated 27 June 2018 - Tomax · 6/27/2018 · Applicant: INOV8 ACCESS PTY LTD 50 5% ....