Future-proof and precise fertilising technology

+ + 100 Hz weighing technology + + + GPS control + + + OptiPoint + + + ISOBUS + + +

With its unique performancepotential, the AXIS-M fertiliserspreader family sets newstandards for tough operatingconditions:

– Maximum spreading precisiondue to coaxial metering anddrop point adjustment – inshort: CDA spreading technology

– Easy-to-use; clear and safeadjustment with the CDAadjustment centre

– Optimum cost efficiency withhigh-speed spreading

– Comfortably large clearances foreasy handling and simple, quickcleaning

2

AXIS will change

fertiliser spreading

forever

Three perfectly adjusted AXIS-M models leave nothing to be desiredfor all power classes.

AXIS-M 20.1 provides professional spreading technology particularlyfor future-oriented businesses (working width: 12 - 36 m).

Its big brother AXIS-M 30.1 provides impressive power with a loadcapacity of three tons and a working width range from 12 to 42 m.

The special characteristics of the AXIS-M 50.1 top model are aworking width ranging from 18 to 50 m, max. load capacity of 4,000 kgand a cat. III three-point linkage especially for large tractors.

Combined with the exclusive RAUCH 100 Hz Weighing Technology,the AXIS-M 20.1 W, 30.1 W, 50.1 W models provide even more precisionand easier operation.

Optionally, AXIS-M 30.1 W and AXIS-M 50.1 W can be supplied withultra-modern, future-proof ISOBUS Technology.

CDA adjustment centre

3AXIS-M 20.1 AXIS-M 50.1 W weighing spreader

Adjusting the spreading dosage isas easy as it is precise. The dosagepre-selection for a adequate finedosing is executed infinitely from 3kg/ha on a large clear scale curve;for the left and right sideseparately.

The DfC scale proportional to theamount – exclusively from RAUCH –allows to quickly vary theapplication quantity proportionallyafter the calibration. The singleactuators are controlledhydraulically or electrically byremote control.

4

Adjustment centre AXIS-M 30.1

It has never been so easy to adjusta two-disc fertiliser spreader. Allfunctions can be adjusted in anergonomically ideal positionquickly and safely with the CDAadjustment centre.

– Fertiliser type and quality

– Working width

– Dosage

Direct contact with doublespreader vanes is no longerrequired during adjustment.

Functionality meets

elegance

Versions with actuator – required control valves

Version K

20.1 30.1 50.1

X X

X X X

X X

X X

X X X

X X X

Hydraulic actuator with 2 ew control valves, separate right/left side

Version D Hydraulic actuator with 2 dw control valves, separate right/left side

Version R Hydraulic actuator with 1 ew control valve, separate right/left side

Version Q Electronic fertiliser dosing, depending on driving speed QUANTRON-A

Version C Electrical actuator with E-Click

Version W 100 Hz weighing system with QUANTRON-E2

Version C with E-Click

Adjustment centre AXIS-M 20.1

5

Urea

Potash granules

SSA

CAN

NPK

PK

Snail granules

Fine seeds

The clear, comprehensive fertiliser chart contains allrelevant adjustment information. Typically RAUCH:detailed data on snail granules and seeds are listed inthe fertiliser chart and the internet: www.rauch.de

One easy to control turn at the CDA adjustment centreis sufficient to adjust AXIS-M quickly and safely to therequired fertiliser type and quality and the workingwidth. The desired dosage can also be easily adjustedat the adjustment centre.

2

The perfect combination offunctions:

Fertiliser dosage,

Fertiliser transfer,

Spreading fertiliser over thewhole working width

determines the quality of thespreading pattern.

Indicators for a secure spreadingpattern are wide spreading flanksand therefore also wideoverlapping zones.

The spreading pattern is thereforeless sensitive to external influenceslike weather or fertiliser property.

The result: perfect, securespreading patterns

6

Modern crop

production requires

efficient solutions!

Granusafe:

The granulate determines the

precision – grain by grain

The fertiliser-protective innovative Granusafe system guarantees thegentle and precise transfer of the sensitive granulate from thecontainer to the field via the spreader vanes.

Thanks to the harmonious design of:

• the agitators, which rotate slowly at just 17 rpm and featureoverload protection

• the flow-optimized slide openings located near the centre

• the brush-shaped turbulence stoppers

• and the aerodynamic Airfins on the spreading discs

grinding effects, the formation of broken or crushed gains and airturbulence in the sensitive spreading zone are reduced to aminimum. As a result, the precision-determining flightcharacteristics of even pressure-sensitive granulates are maintained.The spreading discs, rotating at high speeds (900 rpm), acceleratethe fertiliser granules to an optimum release speed.

The result: precise spreading patterns and thus the optimumnutrient supply to crops.

7

Driving at the limit without hitting the boundaries.

AXIS-M is designed consistently for speed at highest spreadingprecision. With AXIS-M, both the smallest application quantitiesstarting from 3 kg/ha as well as the largest application quantity canbe spread precisely without being influenced by driving speed andworking width.

The long and wide CDA slide opening at the disc centre and thegentle high-tech fertiliser transfer to the spreader vanes permitimpressive working speeds of up to 25 km/h without losing anyprecision.

Even under extreme conditions, e.g. 24 m working width, 25 km/hdriving speed, AXIS-M still allows an impressive application rate of500 kg/ha in NPK fertilising.

With High-speed spreading, AXIS-M offers an as yet unachievedpotential for efficient cost reduction and increased power infertiliser application.

High-Speed-Spreading

Quantity stabilityThe CDA spreading technologyallows precise, even spreadingpatterns even with extremelyvarying application quantities anddriving speeds.This means that AXIS-M spreadersprovide ideal conditions for high precision in area-specific cropproduction and precision farming.

Spreading quantity 150 kg/ha, CV value 6.76 %

Spreading quantity 350 kg/ha, CV value 4.46 %

Spreading quantity 350 kg/ha, CV value 4.46 %

12 km/h

16 km/h

20 km/h

8

In Combination with the RAUCH weighing system, QUANTRON-E2checks the application quantity 100 times per second – duringtravel. Spreading errors due to varying flow characteristics of thespreading material or changes in driving speeds are detectedimmediately and corrected automatically once per second.

While spreading, the smart electronics record all data automaticallyand ensure error-free documentation. The current remainingquantity is displayed at all times. On extreme slopes, the systemsimply switches to hillside spreading mode.

For AXIS-M 20.1 W and 30.1 W the small distance from the centreof gravity and the extremely low intrinsic weight allows the use oftractors in the lower performance range without any problems.

The future on board

Due to their RS 232 interface, the AXIS-M weighing spreaders areideally prepared for current applications in area-specific cropproduction as well as for the use of the RAUCH GPS control toautomatically open and close the metering slide at the ideal time.The off-the-shelf

USB interface provides elegant data exchange between theQUANTRON-E2 and a PC or the internet.

Optionally, AXIS-M 30.1 W and 50.1 W can be supplied with ultra-modern, future-proof ISOBUS technology.

100 Hz weighing

technology

Automation,

innovation, precision

Weighing technology in perfection

Weighing frame with two weighing cells.

AXIS-M 50.1 W: Electrical remote-controlled drop point adjustment

The modern innovative RAUCH CCI terminal* makes theintroduction of the future-proof ISOBUS technology as easy as it isconvenient. A clear operating logic, high-quality colour touchscreen technology and plenty of applications with CCI.Appsincrease efficiency and precision; not only for mineral fertilisationbut also for sowing, plant protection and many other procedures.

9

Innovative RAUCH ISOBUStechnology for AXIS-M weighingspreaders 30.1 W and 50.1 Wallows familiar operation withalready existing ISOBUS operatingterminals from a variety ofproviders and machines.

ISOBUS

Utilise synergies –

increase efficiency

9

CCI-Terminal – ISOBUS can be so easy

ISOBUS synergies

RAUCH ISOBUS weighingspreaders are compatible withMüller Elektronik John Deere,Fendt universal terminal

QUANTRON-VT: The inexpensivealternative for everybody whodoes not use CCI.Apps.

* expert partner: Amazone, Bergmann, Grimme, Kuhn, Krone, Lemken, Pöttinger,Rauch, Ropa, Peecon

CCI.Apps allow perfect adaption to the desiredapplication

CCI.ControlDocumentation and order processing

Parallel TrackingParallel driving aid

Field NavSection ControlAutomatic sectioncontrol

CCI.TecuTractor data

CCI.ConvertSerial interface to connect N sensors,for example (only in combination withCCI.Control)

Fertilizer ChartThe fertiliser charts can beaccessed via the CCI.Terminal

Series:

Optional:

QUANTRON-A regulates the opening position of the metering sliderand thus the flow rate depending on the driving speed and thespecified application rate.

At varying driving speeds, the pre-selected spreading quantityremains equal at all times.

QUANTRON-A impresses with its large, clear display and its logicallystructured menu navigation. All functions can be electrically andremotely controlled, both comfortably and safely with just onehand.

– Opening and closing the metering slides

– Controlling of sections

– Adjusting the quantity while driving, even separately on the rightand left

– Reducing the quantity for boundary spreading.

– Modern precision farming applications using the RS 232 serialinterface

– Documentation and storage of operating data for 200 parcels,including fertiliser name and type.

– Data manager software via off-the-shelf USB interface

– Data manager software for data exchange with PCs or the Internet(optional)

– Displaying the position for TELIMAT T25 boundary spreadingsystem (optional)

– Display of remaining quantity sensor (optional)

– GPS control – automatic opening and closing of the meteringslides in headlands and slopes (optional)

10

QUANTRON-A

metering electronics

An intelligent spreader

QUANTRON-A is the drivingspeed dependent electronicfertiliser metering solution forthe entire AXIS-M family.

Data exchange via USB stick

N-sensor connection

Serial interface for precision farming

QUANTRON-A

The GPS controlled automatic headland and partial width controlQUANTRON guide optimises fertiliser spreading on headlands andslopes.

RAUCH QUANTRON guide, including the Egnos GPS antenna, can becombined with all RAUCH QUANTRON-A/-E/-E2 displays.

Unique in spreading technology, the QUANTRON guide’s innovativeOptiPoint control opens and shuts the metering slide at the idealdistance to the field boundary at all time. On field slopes, theQUANTRON guide controls the left and right sections at the idealmoment.

The result: Maximum ease of operation, high spreadingprecision in sensitive slope and headland areas and higherefficiency by using precise parallel tracking

QUANTRON guide can be modified to a full-value ISOBUS universalterminal with the optional software applications UT (universalterminal), TC (task controller), SC (section controller) and Field-Nav.

Alternatively, GPS terminals by Teejet (Matrix 570 G) or Trimble (CFX 750) can be used in combination with the QUANTRON-A/-E2.

11

GPS-Control

Precise and comfortable on the headland

– with variable slopes

Precision and efficiency in theheadlandBrilliant – the ideal control points forthe edge metering slide are calculatedprecisely for every fertiliser type andeach working width. With thespreading distance parameter of thefertiliser chart both the specificfertiliser spreading behaviour and thetypical spreading patterncharacteristics are considered.Independently of the operator, thefertiliser distribution is optimisedautomatically in the headland.

Optimal switch point

Fertiliser 1

Fertiliser 2

Teejet Matrix 570 G Trimble CFX 750

12

Increased functionality

by tailor-made solutions

Optional equipment

TELIMAT T25/T50 allows precise edge and boundary spreadingfrom the first pass without loss. TELIMAT is folded in front of thespreader disc by remote control with single-acting hydrauliccontrols. TELIMAT can be reliably monitored using an easily visiblemechanical position display.

GSE 25 plus/GSE 50 is the boundary spray unit for AXIS-M 20.1/30.1and AXIS-M 50.1 for precise spreading right on the field boundary. Ifrequired, the simple manual operation can also be performed withsingle-acting hydraulic controls.

TELIMAT T25/T50 and GSE 25 meet European environmentalstandards.

The elaborate lighting system BLW 25 with dust and spray guardsand high-visibility reflective warning panels ensure on-road safetyeven at poor visibility or when the machine is very dirty.

The large ASR 25 parking rollers allow more flexibility for mountingand dismounting the spreader. A quick-release coupling systemallows the rollers to be easily removed or mounted in the transportposition at any time.

The high-quality UV-stabilised hopper covers ensure problem-freespreading even in adverse weather conditions. The generouslyoverlapping cover edges protect the expensive fertiliser even onlong journeys. The entire load area is available at all times in theevent of overload.

One typical RAUCH feature is the two large inspection windows onthe hopper cover for the easy checking of the fill level.

Boundary spreading unit GSE 25 plus

TELIMAT T25 incl.position display

TELIMAT T50 with electrical control

Optional equipment

13

– Container tops in narrow (L) or wide(XL) designs

– Hopper cover with large inspectionwindow

– TELIMAT T25 edge and boundaryspreading system (optional)

– Boundary spreading unit GSE 25plus/GSE 50 (AXIS-M 20.1/30.1)

- VxR plus coated spreader vane forspreading discs S2 and S4

– Climbing ladders for wide XLextensions

– Dirt trap AXIS-M 20.1

– Parking rollers

– TeleSpace articulated shaft

– PPS 5 practical test set

– Fertilizer Identification System DiS

Electronics:

– Data manager for USB data transfer between QUANTRON-E/E2/A and PC

– GPS Control: automatic headland and section control

– Driving speed sensor for QUANTRON-A/-E2

– GPS speed sensors

– TELIMAT sensor for position display with QUANTRON-A/-E2 + ISOBUS

L 800

L 1500 XL 1300

XL 1800 XL 1103

L 603

GLW 1000 GLW 2000

Extensions:

14

Standard calibration test system

The European environmental standard concerning fertiliserspreaders requires that these are fitted with calibration test devicesand hopper purging facilities. Since fertilisers vary enormously, onlythe calibration test provides the security you need.

On AXIS-M, the calibration test device is perfectly integrated intothe machine. An ingenious quick-release coupling allows thespreader disc to be removed without any tools. This createsadequate space for fertiliser collection: Simple for calibration, quickand convenient for hopper purging.

The RAUCH PPS 5 practical test set permits cross-distribution to bechecked and corrected quickly and easily in the field. This provideseven more safety and accuracy during spreading, particularly withfertilisers of poor quality, problematic discharge properties orunknown origin.

Adjustments can be made amazingly fast and reliably thanks to theeasy-to-understand AXIS-M-CAD setting logic.

Experience is good

– having control is better

The RAUCH DiS fertiliser identification system allows the quickdetermination of spreader settings, particularly for fertilisers notlisted in the fertiliser chart. (Optional equipment)

PPS 5 practical test set (optional equipment)

DiS (Optional equipment)

Optional equipment

RAUCH QUALITY

15

The sum of many

solutions in detail

determine the overall

functionality

AX-Drive – maintenance-free gear technology withoverload protection

The innovative AX Drive for spreader discs andagitators runs maintenance-free for years. Unique infertilising technology: AXIS is supplied with overloadsafety systems that protect the entire gear unitincluding the gentle agitators from overstress,blockage, incorrect operation or jerky take-off shafts.

ACS – Anti Corossion Shell

The high stainless steel content, high-quality plasticsand quality surface treatment with the latest powdercoating techniques provide an effective protective shellagainst corrosion and mechanical stress. The value andfunction of your investment will last for years.

VxR plus spreader vanes: spread longer

The highly wear-resistant VxR-plus coating increasesthe spreader vane life-cycle by many times, especiallywhen using jagged, abrasive spreading materials. Thespreader blades S6, S8, S10 and S12 have VxR pluscoated spreader vanes as a standard feature.

Standard equipment

Performance data Workingwidth

m

Hoppervolume

l

Maximumpayload

kg

Filling height

cm

Hopper sizecm

Weight

kg

Extensions Hopper sizecm

Filling height

cm

Weight

kg

Total volume

l

AXIS-M 20.1 / 20.1 W 12 – 36 1000 2100 95 240 x 130 295/350

AXIS-M 30.1 / 30.1 W 12 – 42 1200 3000 101 240 x 130 320/375

AXIS-M 50.1 / 50.1 W 18 – 50 2000 4000 125 290 x 150 620/700

L 603 240 x 130 + 0 + 30 1600 1800 -

L 800 240 x 130 + 26 + 45 1800 2000 -

L 1500 240 x 130 + 50 + 75 - 2700 -

XL 1103 280 x 130 + 23 + 60 2100 2300 -

XL 1300 280 x 130 + 38 + 65 - 2500 -

XL 1800 280 x 130 + 52 + 75 - 3000 -

GLW 1000 290 x 150 + 25 + 80 - - 3000

GLW 2000 290 x 150 + 45 + 130 - - 4000

Spreading discs

S2 option: VxR plus 12 – 18 m

AXIS-M 20.1 AXIS-M 30.1 AXIS-M 50.1

x x

x x x

x x x

x x

S4 option: VxR plus 18 – 28 m

S6 VxR plus 24 – 36 m

S8 VxR plus 30 – 42 m

xS10 VxR plus 36 – 48 m

xS12 VxR plus 42 – 50 m

VxR plus: Chromium carbide overlay of the paddles for extra-long idle periods

AXIS-M 20.1

CDA spreading technology, high speed spreading, calibration sample test, 2 large filling filtersSpreading blade covers, safety clips, container floor, metering slide, spreading vanes, stainless steel agitator shaft

Power take-off 540 rpm; maintenance-free closed Walterscheid oil bath gears

Weighing technology

100 Hz weighing technology with two weighing cells, electrical remote controlled drop-point adjustmentQUANTRON-E2 metering computer with USB interface for data transfer, mudflaps

AXIS-M 30.1 AXIS-M 50.1

– CDA spreading technology– Articulated shaft with

shear bolts– Cat. II three-point

geometry

ISOBUS option ISOBUS optionTELIMAT T50, electrically remote controlled

– CDA spreading technology– Articulated shaft with star ratchet

overload protection– Mudflaps– Illuminated warning signs– 2 windows for fill level control– Cat. II three-point geometry

– CDA spreading technology– Articulated shaft with star ratchet overload

protection– Gears for 540 or 750 rpm take-off shafts– Mudflaps– Illuminated warning signs– 2 windows for fill level control– Cat. II three-point geometry

Good reasons for AXIS-M

Precise CDA spreading technology

The innovative coaxial metering and drop point positioning providesenormous potential for reliable, precise, requirement-based nutrientsupply to crops.

Amazingly simple adjustment

Just one small turn of a knob on the operating terminal is all that’sneeded to adjust AXIS-M quickly and accurately to the spreadingmaterial’s properties and the required operating width.

Edge and boundary spreading according to Europeanenvironmental standards*

The TELIMAT T25 and GSE 25 boundary spreader units allowconvenient and precise spreading at field boundaries.

More power with high-speed spreading

High-speed spreading allows driving speeds over 20 km/h withoutany loss of spreading accuracy.

Gentle for granulates

The Granusafe system gently guides even the most pressure-sensitive fertiliser granulate from the hopper to the spreader vanesand the field with the utmost care.

Agitator is gentle on the fertiliser

The cast agitator rotates at only 17 rpm. High-quality bearings, sealsand stainless steel agitator ensure operational reliability withoutmaintenance.

Maintenance-free gears for spreading discs and agitator

All transmissions operate in a closed oil bath and are maintenance-free. The standard-fitted overload devices protect transmission andagitator from damage caused by excessive loads.

Less spreader vane wear*

High-quality VxR plus coated spreader vanes extend the service lifesignificantly. For S6 and S8 spreader blades, the VxR plus coating isstandard.

Easy and quick cleaning

Good access to all components and generous amounts of spacemake light work of cleaning and maintenance tasks.

Optimum corrosion protection

The high-quality powder coating, high stainless steel content and theuse of UV-stabilised plastics protect from rust and maintain the valueof your investment.

* Optional

RAUCH Landmaschinenfabrik GmbHD-76545 Sinzheim · Postfach 1162Phone +49 (0) 7221/985-0 · Fax +49 (0) 7221/985-200info@rauch.de · www.rauch.de

We reserve the right to make changes to improve our products.

AXIS

-580

0041

-en-

b-10

13

AXIS-H 50.1 EMC+W Large-area spreader TWS Pneumatic spreader AGT