FTI-HDK2 Type 2B3 - Vehicle Coverage & …...Honda Honda Honda CR-V STD Key Civic STD Key Civic...
2
FTI-HDK2 Type 2B3 - Vehicle Coverage & Preparation Notes Make Model Year Install I/O Changes DL-HA3 Honda Honda Honda CR-V STD Key Civic STD Key Civic Hybrid STD Key 2012-16 2012-15 2012-15 Type 2 Type 2 Type 2 CAN Lights RAP Trunk Green White/Blue Park / Auto Hey! Read this stuff before you start the installation... Firmware: Covered vehicles use BLADE-AL(DL)-HA3 firmware, flash module and update the controller firmware before installing. Install: Type 2 vehicles use the gray 7-pin immobilizer adapter and the 8-pin CN1 adapter, green 7-pin immobilizer adapter is not required. The covered vehicles require use of the 20-pin BLADE connector marked HA3, the HA6 connector is not required and should be secured for safety. Lights: ( - ) Parking lights and Auto-light shutoff require additional wiring and direct connection from the CM I/O connector to the headlight switch connector, as illustrated. Known wire colors and common alternates are included in the list above. Okay, now get to work... IMMO IMMO IMMO *blue/org *gray/org *blue/org *gray/org *blue/org *gray/org CM-900 CM-900S/900AS CM7X00 CM7000/7200 Cut loop for A/T CM900AS/900S Jumper SUPPORT - 1(888) 820-3690, EXT. 203 DEREK ZOOLANDER Est. 2001 CENTER KIDS WHO CAN’T READ GOOD AND W H O W ANNA LEAR N T O D O O T H E R S T U F F G O O D T O O IIIIIIIII IIIIIIIIIIIIIIIIIIIIIII I I I I I I I I I I IIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII for
Transcript of FTI-HDK2 Type 2B3 - Vehicle Coverage & …...Honda Honda Honda CR-V STD Key Civic STD Key Civic...
FTI-HDK2 Type 2B3 - Vehicle Coverage & Preparation Notes
Make Model Year Install I/O Changes
DL-HA3
Honda
Honda
Honda
CR-V STD Key
Civic STD Key
Civic Hybrid STD Key
2012-16
2012-15
2012-15
Type 2
Type 2
Type 2
CAN Lights RAP Trunk
Green White/BluePark / Auto
Hey! Read this stuff before you start the installation...
Firmware:Covered vehicles use BLADE-AL(DL)-HA3 firmware, flash module and update the controller firmware before installing.
Install:Type 2 vehicles use the gray 7-pin immobilizer adapter and the 8-pin CN1 adapter, green 7-pin immobilizer adapter is not required.The covered vehicles require use of the 20-pin BLADE connector marked HA3, the HA6 connector is not required and should besecured for safety.
Lights:( - ) Parking lights and Auto-light shutoff require additional wiring and direct connection from the CM I/O connector to the headlightswitch connector, as illustrated. Known wire colors and common alternates are included in the list above.
Okay, now get to work...
IMMO
IMMO
IMMO
*blue/org*gray/org*blue/org*gray/org*blue/org*gray/org
CM
-900
CM-900S/900AS
CM7X00
CM7000/7200 Cut loop for A/T
CM900AS/900S Jumper
SUPPORT - 1(888) 820-3690, EXT. 203
DER
EK Z
OOLANDER
Est.
2001
CENTER K
IDS
WH
O C
AN’T
READ
GO
OD
AND WHO WANNA LEARN TO D
O O
TH
ER
ST
UF
F G
OO
D T
OO
IIIIIIIII
III
IIIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
II
II
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII
for
A
B
C
D
Harness covers both HA3 and HA6 applications, the BLADE connector is the same for both firmwareapplications and harness configurations including those requiring use of ADPT B.
HDK2 harness provides multiple immobilizer/parking light connections, this install type uses the grayType 2 immobilizer connector as illustrated
Type 2 installations REQUIRE using the included CN1 adapter. Please note, Types 1 & 2 havedifferent ACC, IGN, and START circuit locations, proper programming and operation depend on usingthe correct CN1 configuration. This install type does not use the Type 1 immobilizer adapter(+) Parking lights are provided for convenience, ( - ) parking lights and GWR for Auto-light off areavailable in the CM I/O connector . Type B parking lights pin #8, auto-lights off pin #1, colors varyby model, but pin positions remain constant.
LED Programming Error CodesModule LED flashing RED during programming
1x - CAN error, confirm immobilizer connections
12
SUPPORT - 1(888) 820-3690, EXT. 203
FTI-HDK2 Type 2B3
Module Programming ProcedureStep 1 - Insert key into cylinderStep 2 - Activate IGNStep 3 - Wait for module LED to go solid blueStep 4 - Deactivate IGNStep 5 - Press unlock on OEM remote, programming complete
FTI-HDK2 Type 2B3 - Installation Notes & Wiring Diagram
A
B
BLADE
FUSE
FUSEPK LIGHTS
GWR
PK LIGHTS
( - )
blackgreen/white
66 11
88 77
1
82121
Ignition Switch
Type B Headlight Switch
or
PWR
2
1
B
C
D
AD
*COLORS VARY
CType 1 Immobilizer
8
*Not required
BLADE
GREEN
GRAY
ADPT B
