Fs imms - pdl-o - mdl 501 mastery journey timeline - joel soucie
FS 501 Installation
-
Upload
itsthegris -
Category
Documents
-
view
214 -
download
0
Transcript of FS 501 Installation
7/27/2019 FS 501 Installation
http://slidepdf.com/reader/full/fs-501-installation 1/7
E-1
FS-501 Finisher
4684-7701-01
INSTALLATION MANUAL Applied Machine:
for Product Code 4038
I. Accessory parts
* This machine doesn’t use the Rail guide A.
No. Name Shape Q’ty
1. Rail guide A
1
2. Rail guide B
1
3. Ground plate
1
4. Rail
1
5. Stabilizing pin
1
6. Magnet plate
1
7. Horizontaltransport unit
1
8. Tray
1
9. Protective
guide
1
4698U044AA
4684U061AB
4684U062AA
4683IXC505DA
4683IXC504DA
4698U047AA
4698U048AA
4684U075AA
4684U070AA
10. Label
1
11. Screws A
(4 × 12 mm)
3
12. Screws B
(4 × 8 mm)
2
13. Installation
Manual1
set
14. Spacer
1
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.Putting your head in the wrapper involves
danger of suffocation.
No. Name Shape Q’ty
4684U076AB
4684U072AA
9735U001AA
4980IXC019DA
4583U018AA
7/27/2019 FS 501 Installation
http://slidepdf.com/reader/full/fs-501-installation 2/7
E-2
II. Before Installing the Finisher
In order to adjust the height of the machine to the
height of the finisher, the Paper Feed Cabinet PC-
103, or PC-203, or PC-403, or Desk DK-502 must
be installed.
Machine + Paper Feed Cabinet PC-103/PC-203
Machine + Paper Feed Cabinet PC-403
Machine + Desk DK-502
III. Installation procedures
1. Remove protective tape and packing materials
from different parts of the finisher.
4684IXC007DA
4684IXC008DA
4684IXC009DA
Packing
bracket
Note:
Do not remove these parts.
Packing bracket
C4683U006AB
4684U074AA
C4683U008AA
4683U013AA
4643U003AA
Tape
7/27/2019 FS 501 Installation
http://slidepdf.com/reader/full/fs-501-installation 3/7
E-3
Note:
• Make sure that the installation site is flat and
level.
• After the Finisher has been set up, avoid mov-
ing it unless it is absolutely necessary.
See “VII.Removing the Rail” of P.E-7 to move it.
After moving it, follow step 13 to 15 of P.E-5 and
step 8 and 9 of P.E-4.
2. Turn off the machine and unplug the power cord
from the power outlet.
3. Remove the Sub tray of the machine.
4. Peel off the seal covering the area where the sta-
bilizing pin and magnet plate will be attached.
5. Attach the stabilizing pin and magnet plate to the
left side of the machine as shown (three screw
A’s furnished with the Finisher).
6. Place the Ground Plate in Rail Guide B.
7. Attach the rail guide B to the left side of the Paper
Feed Cabinet as shown in the illustration (two
screw B’s furnished with the Finisher).
Note:
Fit Rail Guide B in the tab on the lower portion of
the Paper Feed Cabinet.
4684IXC001DA
4684IXC002DB
4684IXC003DB
4684U063AB
4684U064AA
7/27/2019 FS 501 Installation
http://slidepdf.com/reader/full/fs-501-installation 4/7
E-4
8. Insert the rail into the Rail Guide B.
9. Protrude the leading edge of the rail out about 60
mm to the right from the right end of the machine.
Note:
• If the rail is pulled out more than necessary, it is
caught by the flat spring fitted to the machine
as it is brought back into the original position.
• When setting it, make sure the rail notch comes
under.
10.Insert the spacer into the rail.
Note:
Slide out the rail to the left and check that it does
not come off the Rail Guide B.
11.Slide the other end of the rail installed in step 8
into the rail guide on the finisher.
Note:
Insert the rail until it snaps into place.
At this time, the finisher should stay attached to
the machine, even if you try to pull it away.
12.Remove protective tape of the horizontal trans-
port unit.
4684U065AA
4684IXC012DA
OK NG
4583U017AB
C4683U011AA
C4683U010AA
C4651U023AB
Tape
7/27/2019 FS 501 Installation
http://slidepdf.com/reader/full/fs-501-installation 5/7
E-5
13.Place the horizontal transport unit on the paper
output section of the machine, and make sure
that the plastic guide pin on the bottom of the hor-
izontal transport unit hooks into the bracket on
the finisher.
14.Press the horizontal transport unit up against the
rear side.
Note:
Make sure that the gear on the finisher and that on
the horizontal transport unit are in positive mesh
with each other.
15.Secure the horizontal transport unit with the lock.
IV. Adjusting the Height and Tilt of the Fin-
isher
1. If the finisher gradually tilts toward the machine,
check the following:
• Are the stabilizing pin and the hole in the finisher
at the same height?
• Is the horizontal transport unit not extremely
tilted?
* If the finisher is not at the same height as the
machine, adjust the machine as follows.
2. Slide the finisher away from the machine, and
then remove the lower-front cover of the finisher
(two screws).
3. Lift the finisher’s two caster covers up, and then
pull them off.
C4683U023AA
C4683U014AA
C4683U013AA
4684IXC004DA
4643U021AB
4643U020AA
7/27/2019 FS 501 Installation
http://slidepdf.com/reader/full/fs-501-installation 6/7
E-6
4. Without turning the adjusting bolt (lower bolt) on
the caster, loosen the securing bolt (upper bolt),
and then turn the adjusting bolt (lower bolt) as
indicated below to adjust the height of the fin-
isher.
<Two rear casters>
If the stabilizing pin is too high:
Turn the bolt clockwise
If the stabilizing pin is too low:
<Two front casters>
If the magnet plate is too high:
Turn the bolt clockwise
If the magnet plate is too low:
Turn the bolt counterclockwise
5. If the finisher tilts toward the machine, check the
following:
• Are distances a and b equal?
* If a and b are not equal, refer to step 4 above and
turn the adjusting bolt (lower bolt) as indicated to
adjust the tilt of the finisher.
6. After the adjustment is finished, without turning
any of the adjusting bolts (lower bolts), tighten
the four securing bolts (upper bolts).
7. Reinstall the caster cover which has been
removed in step 3.
8. Reinstall the lower-front cover which has been
removed in step 2 (two screws).
V. Connecting the Hookup Cord
1. Connect the hookup cord to the horizontal trans-
port unit and the machine.
2. Secure the hookup cord of the Horizontal Trans-
port Unit using the cord clamp (large) of the fin-
isher.
4643U022AB
Securing bolt
Adjusting
bolt
4684IXC005DA
a
b
4643U029AA
Securing bolt
Adjusting bolt
4684IXC014DA
4684U069AA
7/27/2019 FS 501 Installation
http://slidepdf.com/reader/full/fs-501-installation 7/7
E-7
VI. Installing the Tray and Protective Guide
Install the tray and protective guide at the positions
shown in the illustrations.
VII. Removing the Rail1. Pinch together the rail stoppers on the left side of
the finisher to release them.
2. Disconnect the two hookup cords.
3. Remove the horizontal transport unit from the fin-
isher, and then place it on top of the machine.
4. Carefully pull the finisher away from the machine.
5. Slide the rail under the machine, and then
remove it from the right side of the machine.
VIII. Affixing the Labels
Affix the labels to the position shown below.
4643U017AA
4643U024AA
4684IXC015DB
4698U109AA
C4683U018BA
for Machine
for Automatic Doc-
ument Feeder
Label for Machine
Label for Automatic Document Feeder
4684U076AB