FP1200 Spec Sheet (2) [Read-Only] - BuildSite.com · 2013. 8. 30. · Water absorption: ASTM 5-570
Transcript of FP1200 Spec Sheet (2) [Read-Only] - BuildSite.com · 2013. 8. 30. · Water absorption: ASTM 5-570
©Copyright Hubbell Inc. 2011 Bulletin PC-75
Wt. Lbs. Description
ChannelsFP12xx Sloped Channels 96” FP12xxN Neutral Channel 96” FP12xxH Neutral Channel 48”
*see page 12 for channel weights and layouts
FramesFF1200 44 Gray Coated Channel Frame - 96"FF1200H 22 Gray Coated Channel Frame - 48"
AccessoriesFA1200A 3.25 End Cap - 6" Inlet/OutletFA1200S 2.25 Vertical Outlet - 6" OutletFA1200D 1 Splice AdapterFP12xxRE 54.5 Right Hand Elbow Assemblies (05, 10 & 15)FP12xxLE 54.5 Left Hand Elbow Assemblies (05, 10 & 15)FP12xxRT 79 Right Hand Tee Assemblies (05, 10 & 15)FP12xxLT 79 Left Hand Tee Assemblies (05, 10 & 15)
GratesFG1241 42.5 Class C - Ductile Iron - slotted grate - 24"FG1242 58 Class E - Ductile Iron - slotted grate - 24"FG1275 66.75 Class E - Ductile Iron - ADA grate - 24"FG1246 65 Class F - Ductile Iron - slotted grate - 24"
*grates are supplied with bolts and washers
Part No.
FP1200 SERIESSPECIFICATIONS
FA1200A
End Cap with Pipe Outlet
FA1200S
Bottom Outlet Adapter
FA1200D
Splice Adapter
Steel frame cap included
Half Channel End View - InletEnd View - Outlet
Standard Channel
Prefabricated Elbow
Prefabricated Tee
Right and Left turns available
5, 10, & 15 Depths
Right and Left inlet designs available
5, 10, & 15 Depths
General Dimensions
48.00"
INLETDEPTH
50.75"
96.00"
98.75"
REBAR BRACKET NELSON STUD
14.73"21.87"
12.19"
13.06"R6.09"
14.73"21.87"
R6.09"12.56"
12.19"OUTLETDEPTH
24.00"
24.00"
41.12"
50.00"
48.00"
24.00"
24.00"
15.00"
24.59"
FITS 6", 8", & 10" PIPE
12.57"
2.62"
9.03"
FITS 6", 8" & 10" PIPE
12.00"
12.62"
22.44"
R6.31"1.00"
R6.31"
6.31"
1.00"
8.46"
Wt. Lbs. Description
FP1251 Catch BasinFP1251 26 12" x 24" Catch BasinFF1251 15.5 FP1251 Grey Coated Frame
GratesFG1241 42.5 Class C - Ductile Iron - slotted grate - 24"FG1242 58 Class E - Ductile Iron - slotted grate - 24"FG1275 66.75 Class E - Ductile Iron - ADA grate - 24"FG1246 65 Class F - Ductile Iron - slotted grate - 24"
*grates are supplied with bolts and washers
AccessoriesFP1200L 0.5 FP1200 Series Inlet AdapterFP1251U 2 Catch Basin 6"/8"/10" Pipe Outlet
FP1255 Catch BasinFP1255 34 24" x 24" Catch BasinFF1255 19.25 FP1255 Grey Coated Frame
GratesDG0659 20 Class A - Fiberglass - ADA bar grateDG0653D 130 Class D - Ductile Iron - slotted grate
*grates are supplied with bolts and washers
AccessoriesFP0800L 0.5 FP0800 Series Inlet AdapterFP1200L 0.5 FP1200 Series Inlet AdapterFP1251U 2 Catch Basin 6"/8"/10" Pipe OutletFA2424TA Trash Basket
Part No.
SPECIFICATIONSUniversal Catch Basins
SQ. 24.52"
34.06"
24.38" 15.06"
34.06"
FP1200 GratesFP1251 Catch Basin & Grates
Slotted Iron - 1241, 1242, 1246
ADA Iron - 1275
FP1255 Catch Basin & Grates Slotted Iron - 653D
Fiberglass ADA Bar - 659
Accessories
FA1251U - Pipe Outlet
FA1200L – Catch Basin Inlet
FP1200 SERIES
Slotted Iron - 1241, 1242, 1246
ADA Iron - 1275
12.62"
1.56"R6.31"
23.44"22.32"
0.94"
14.87"
4.13" 9.50"
FITS 6",8" & 10"PIPE11.33"
11.33"
Part Number
Inlet Depth (in.)
Outlet Depth (in.)
Flow (gpm)
Flow Velocity
(fps)Wt. (lbs)
Part Number
Inlet Depth (in.)
Outlet Depth (in.)
Flow (gpm)
Flow Velocity
(fps)Wt. (lbs)
1201 8.07 9.03 2057 7.02 29.6 1209 15.75 16.71 4728 7.02 48.81202 9.03 9.99 2381 7.02 32.0 1210 16.71 17.67 5069 7.02 51.21203 9.99 10.95 2709 7.02 34.4 1211 17.67 18.63 5412 7.02 53.61204 10.95 11.91 3040 7.02 36.8 1212 18.63 19.59 5756 7.02 56.01205 11.91 12.87 3374 7.02 39.2 1213 19.59 20.55 6101 7.02 58.41206 12.87 13.83 3710 7.02 41.6 1214 20.55 21.51 6446 7.02 60.81207 13.83 14.79 4047 7.02 44.0 1215 21.51 22.47 6792 7.02 63.21208 14.79 15.75 4387 7.02 46.4
SPECIFICATIONSConfiguration Chart
FP1200 SERIES
TRENCH DRAIN SPECIFCATION
General: The work specified in this section shall consist of furnishing and installing preformed trench drains including drain channels, frames, grates, and accessories as shown on the contract plans. The surface drainage system shall be POLYCAST FP1200 High Capacity Trench Drain. One manufacturer shall provide all drain components unless noted otherwise at piping connections. The number of component joints shall be minimized for products in this section.
Materials: The preformed trench drain shall be a polyester matrix as shown on the contract plans. The frame clear opening dimension shall be 11.86“. The channel widths shall be 12.19” with a full bottom radius. The frame shall fully support the grate and transfer vertical loads linearly into adjacent concrete.Sloped and non-sloped channels shall be used as shown in contract plans. Channels shall be 8' long. Sloped channels shall have a minimum 1% inverted slope. Maximum capacity without extensions shall be 6700 GPM at flat and level grade. The channels shall permit a continuously sloped run of 120' without extensions.
The fiberglass channels shall have minimum material properties as follows:
DESCRIPTION TEST METHOD VALUESWater absorption: ASTM 5-570 <1%Chemical resistance: ASTM D-543 75% strength, <2% change in weight/dimensionAccelerated service ASTM D-7566-E 75% strength, <2% change in weight/dimensionCTE (coefficient of thermal expansion) ASTM D-696 4.4x10-6 in/in/°F
Grates and Frames: The grating and frames shall be made of steel (ASTM A-36), ductile iron (ASTM A-536 minimum grade 65-45-12), or gray iron (ASTM A-48) and meet DIN 19580 and FAA 150-5320-6E load requirements. The frames shall be non-removable from the concrete. The grates shall be removable or non-removable as shown on the contract plans. Removable grates shall have threaded bolt lockdowns that do not unduly impede fluid flow in the channel. The lockdowns shall withstand cyclical loads of 700 pounds after salt exposure per ASTM B-517.
Installation: The manufacturer’s installation recommendations shall be followed. The reinforcement in the concrete surrounding the drain shall be adequate for the anticipated loads. The trench drain shall not be used in place of a defacto expansion joint.