FireFox GB 29052013 - GESIPA and threaded mandrels Tool versions Accessories System components &...
2
312 312 Ø31 31 68 68 Ø50 50 275 275 Ø106.5 106.5 217.5 217.5 Working range Technical Data Standard Accessories Standard equipement Spécial accessories • Complete sets of nosepieces and threaded mandrels • Adapters for use of allen DIN EN ISO 4762 (12.9 quality) instead of threaded mandrels M4 to M8 • Adapters for setting of blind rivet nut studs M4 to M8 • Nosepieces and threaded mandrels with UNF/UNC threads Threaded mandrel and nosepiece from M3 to M12 as per customer’s choice 2 wrenches SW24/27 1 allen screw driver SW4 1 oil can with 100ml hydraulic oil 1 oil refilling can Operation manual Weight: 2,4 kg ( 4,4 lbs) Course, ajustable, max: 10mm Traction force, ajustable max: 18,5 KN at 5 bar Operating air pressure: 5-7 bar Air hose connection: 6 mm Ø (1/4’’) Air consumption: Approx. 2 to 4 l per cycle (depends of nut size) From M3 to M12 all materials Performances FireFox ® — Just innovative! Most blind rivet nut setting tools on the market are stroke controlled, while only a handful are traction force controlled. GESIPA ® now offers both features together in a single pneumatic-hydraulic tool and provides the user with the choice between both setting modes: easy, fast and safe! FireFox ® — The new one FireFox ® — The canny one … can be operated with DIN EN ISO 4762 allen screws instead of threaded mandrel. Special adapters available as accessory for M4 to M8 threads allows the original threaded mandrels to be replaced by allen screws: a substantial cost saving without any quality or perfor- mance loss and higher endurance when far away from the spare parts source. Best results are obtained with 12.9 grade screws. FireFox ® — The reliable one FireFox ® — The versatile one Sets blind rivet nuts from M3 to M12, also those with extended grip range. The wide range of suitable thread sizes provides the FireFox ® with a large variety of possible operation. The choice bet- ween stroke and traction force control also makes it suitable for industrial applications where several material thicknesses need to be covered, which would normally require the use of several tools. Moreover, its outstanding 10mm stroke is ideally suited to the new generation of large grip range blind rivet nuts, like the GESIPA ® PolyGrip ® products. Setting blind rivet nuts with constant stroke adjustment This means that the tool will pull the blind rivet nut with its maximum force and stop immediately when the pre-adjusted stroke has been covered, nut for nut, safely and reliably. The stroke adjustment is easily and clearly performed using a millimetre scale on the tool adjustment thumb wheel, without the need for any tool, after having adjusted the pulling force to its maximum. The millimetre adjustment scale exactly reflects the effective stroke of the threaded mandrel, so that maladjust- ment is nearly impossible. Moreover it is safely locked to prevent any drift. The protruding length of the threaded mandrel can be adjusted manu- ally according to the shaft length of the blind rivet nut. Setting blind rivet nuts with traction force adjustment This means that the tool will stop pulling the blind rivet nut when a pre-adjusted traction force threshold is reached. No re-adjustment is needed when setting blind rivet nuts into different material thicknesses or when using blind rivet nuts with different shaft lengths. Traction force control prevents damage of the material which cannot be overstressed by a too high setting pressure and preserves the integrity of the blind rivet nut thread. As a bonus, it also extends the life duration of the threaded mandrels. The desired traction force threshold can be very simply adjusted with an allen wrench once the stroke adjustment has been set to the maximum. FireFox ® — All inclusive The FireFox ® special accessories GESIPA ® not only offers threaded mandrels and nosepieces for the current thread sizes M3 to M12, but also adapters for blind rivet nut studs from M4 to M8. This range of threaded mandrels and nosepieces is also availa- ble with equivalent UNC/UNF thread dimensions. All these parts can be ordered separately, either individually or in complete sets. They are not included in the standard delivery of the tool. FireFox ® — The simple one Easy operation through automatic drill-on function The drill-on process will automatically start when a blind rivet nut is lightly pressed onto the mandrel tip. This avoids the cumbersome double action on twin triggers. Thereafter introduce the blind rivet nut into its setting hole, press the trigger and keep it depressed until the setting cycle is completely finished, nut drilled off and tool free. It couldn’t be easier! FireFox ® — The fast one Extremely fast working cycle Great care has been taken to shorten every sequence of the setting cycle to its absolute minimum: Pulling sequence and subsequent automatic drill-off take place at breathtaking speed and require only a single action on the trigger. FireFox ® — The complete range This new tool doesn’t come alone. GESIPA ® is offering a comprehensive range of accessories in order to cope with special applications and difficult tasks: easy, fast and safe!
Transcript of FireFox GB 29052013 - GESIPA and threaded mandrels Tool versions Accessories System components &...
312
312
Ø3131
6868
Ø5050
275275
Ø106.5106.5
217.5
217.5
Working range
Technical Data
Standard Accessories
Standard equipement
Spécial accessories• Complete sets of nosepieces and threaded mandrels• Adapters for use of allen DIN EN ISO 4762 (12.9 quality) instead of threaded mandrels M4 to M8• Adapters for setting of blind rivet nut studs M4 to M8• Nosepieces and threaded mandrels with UNF/UNC threads
Threaded mandrel and nosepiece from M3 to M12 as per customer’s choice
2 wrenches SW24/271 allen screw driver SW41 oil can with 100ml hydraulic oil1 oil refilling canOperation manual
Weight: 2,4 kg ( 4,4 lbs)Course, ajustable, max: 10mmTraction force, ajustable max: 18,5 KN at 5 barOperating air pressure: 5-7 barAir hose connection: 6 mm Ø (1/4’’)Air consumption: Approx. 2 to 4 l
per cycle (depends of nut size)
From M3 to M12 all materials
Performances FireFox ® — Just innovative!Most blind rivet nut setting tools on the market are stroke controlled, while only a handful are traction force controlled. GESIPA® now offers both features together in a single pneumatic-hydraulic tool and provides the user with the choice between both setting modes: easy, fast and safe!
FireFox® — The new one FireFox® — The canny one
… can be operated with DIN EN ISO 4762 allen screws instead of threaded mandrel.Special adapters available as accessory for M4 to M8 threads allows the original threaded mandrels to be replaced by allen screws: a substantial cost saving without any quality or perfor-mance loss and higher endurance when far away from the spare parts source. Best results are obtained with 12.9 grade screws.
FireFox® — The reliable one FireFox® — The versatile one
Sets blind rivet nuts from M3 to M12, also those with extended grip range.The wide range of suitable thread sizes provides the FireFox® with a large variety of possible operation. The choice bet-ween stroke and traction force control also makes it suitable for industrial applications where several material thicknesses need to be covered, which would normally require the use of several tools.Moreover, its outstanding 10mm stroke is ideally suited to the new generation of large grip range blind rivet nuts, like the GESIPA® PolyGrip® products.
Setting blind rivet nuts with constant stroke adjustmentThis means that the tool will pull the blind rivet nut with its maximum force and stop immediately when the pre-adjusted stroke has been covered, nut for nut, safely and reliably. The stroke adjustment is easily and clearly performed using a millimetre scale on the tool adjustment thumb wheel, without the need for any tool, after having adjusted the pulling force to its maximum. The millimetre adjustment scale exactly reflects the effective stroke of the threaded mandrel, so that maladjust-ment is nearly impossible. Moreover it is safely locked to prevent any drift.The protruding length of the threaded mandrel can be adjusted manu-ally according to the shaft length of the blind rivet nut.
Setting blind rivet nuts with traction force adjustmentThis means that the tool will stop pulling the blind rivet nut when a pre-adjusted traction force threshold is reached. No re-adjustment is needed when setting blind rivet nuts into different material thicknesses or when using blind rivet nuts with different shaft lengths. Traction force control prevents damage of the material which cannot be overstressed by a too high setting pressure and preserves the integrity of the blind rivet nut thread. As a bonus, it also extends the life duration of the threaded mandrels.The desired traction force threshold can be very simply adjusted with an allen wrench once the stroke adjustment has been set to the maximum.
FireFox® — All inclusive
The FireFox® special accessoriesGESIPA® not only offers threaded mandrels and nosepieces for the current thread sizes M3 to M12, but also adapters for blind rivet nut studs from M4 to M8.This range of threaded mandrels and nosepieces is also availa-ble with equivalent UNC/UNF thread dimensions.All these parts can be ordered separately, either individually or in complete sets. They are not included in the standard delivery of the tool.
FireFox® — The simple one
Easy operation through automatic drill-on functionThe drill-on process will automatically start when a blind rivet nut is lightly pressed onto the mandrel tip. This avoids the cumbersome double action on twin triggers. Thereafter introduce the blind rivet nut into its setting hole, press the trigger and keep it depressed until the setting cycle is completely finished, nut drilled off and tool free. It couldn’t be easier!
FireFox® — The fast one
Extremely fast working cycleGreat care has been taken to shorten every sequence of the setting cycle to its absolute minimum: Pulling sequence and subsequent automatic drill-off take place at breathtaking speed and require only a single action on the trigger.
FireFox ® — The complete rangeThis new tool doesn’t come alone. GESIPA® is offering a comprehensive range of accessories in order to cope with special applications and difficult tasks: easy, fast and safe!
Nosepieces and threaded mandrels
Tool versions
Accessories
System components & accessories FireFox ®
The new GESIPA® hydro-pneumatic toolsets blind rivet nuts…
and the benchmark as well!
FireFox ®highlights• Selectable stroke or
pulling force control• Automatic drill-on func-
tion• Extremely fast working
cycle• For M3 to M12 blind
rivet nuts• Threaded mandrels can
be replaced by allen screws
• Comprehensive range of accessories
Special threaded mandrels (extended length or fi ne thread) available on request
FireFox® with threaded mandrel M6 Part number 772 0001
FireFox® with threaded mandrel M3 Part number 772 0002
FireFox® with threaded mandrel M4 Part number 772 0003
FireFox® with threaded mandrel M5 Part number 772 0004
FireFox® with threaded mandrel M8 Part number 772 0005
FireFox® with threaded mandrel M10 Part number 772 0006
FireFox® with threaded mandrel M12 Part number 772 0007
Nosepiece M3 Part number 772 1053 Threaded Mandrel M3 Part number 772 1046
Nosepiece M4 Part number 772 1054 Threaded Mandrel M4 Part number 772 1047
Nosepiece M5 Part number 772 1055 Threaded Mandrel M5 Part number 772 1048
Nosepiece M6 Part number 772 1056 Threaded Mandrel M6 Part number 772 1049
Nosepiece M8 & 5/16“ - 18 UNC Part number 772 1057 Threaded Mandrel M8 Part number 772 1050
Nosepiece M10 Part number 772 1058 Threaded Mandrel M10 Part number 772 1051
Nosepiece M12 Part number 772 1059 Threaded Mandrel M12 Part number 772 1052
Nosepiece 6 - 32 UNC Part number 772 1108 Threaded Mandrel 6 - 32 UNC Part number 772 1101
Nosepiece 8 - 32 UNC Part number 772 1109 Threaded Mandrel 8 - 32 UNC Part number 772 1102
Nosepiece 10-24 UNC/10 - 32 UNF Part number 772 1110 Threaded Mandrel 10 - 24 UNC Part number 772 1103
Threaded Mandrel 10 - 32 UNF Part number 772 1104
Nosepiece 1/4“ - 20 UNC Part number 772 1111 Threaded Mandrel 1/4“ - 20 UNC Part number 772 1105
Nosepiece M8 & 5/16“ - 18 UNC Part number 772 1057 Threaded Mandrel 5/16“ - 18 UNC Part number 772 1106
Nosepiece 3/8“ - 16 UNC Part number 772 1113 Threaded Mandrel 3/8“ - 16 UNC Part number 772 1107
Conversion kit for DIN screws M4 Part number 772 1117
Conversion kit for DIN screws M5 Part number 772 1132
Conversion kit for DIN screws M6 Part number 772 1136
Conversion kit for DIN screws M8 Part number 772 1137
Conversion kit for blind rivet nut studs M4 Part number 772 1138
Conversion kit for blind rivet nut studs M5 Part number 772 1139
Conversion kit for blind rivet nut studs M6 Part number 772 1140
Conversion kit for blind rivet nut studs M8 Part number 772 1141
Complete set metrisch Part number 772 1115 Complete set UNC/UNF Part Number 772 1142
05/2
013
- 79
0 03
51
Working with stroke control?When always the same blind rivet nut size is to be set into the same material thickness, working with stro-ke control will be just fi ne.
Or working with pulling force control?Pulling force control should be used when one blind rivet nut diameter size with various lengthes (ex: M6 x 15,5 and M6 x 18) is to be set into changing material thicknesses.
GESIPA Blindniettechnik GmbH T +49 (0) 6105 962 0Nordendstraße 13-39 F+49 (0) 6105 962 28764546 Mörfelden-Walldorf [email protected] www.gesipa.com
A company of
GESIPA Blindniettechnik GmbH T +49 (0) 6105 962 0Nordendstraße 13-39 F+49 (0) 6105 962 28764546 Mörfelden-Walldorf [email protected] www.gesipa.com
A company of
