Fiber Storage Center (FSC3) Instructions -...
2
Fiber Storage Center (FSC3) Instructions The fiber storage center (P/N: FSC3-(XX)) may be mounted to a 19” or 23” rack depending on the orientation of the mounting brackets. (19” position shown.) Select one of the three sets of mounting holes, based on front/rear clearance requirements, and secure the mounting brackets to each side of the FSC3 using #10-32 screws provided. 1 Position the fiber storage center in the desired loca- tion on the rack and secure with the four (4) #12-24 screws and washers provided. Note: #10-32 screws and washers may also be used (not provided). 2 Open the front door by depressing the latch locat- ed at the upper center of the door. 3 If required, remove the door from the hinges by squeezing the securing latches inward until disengaged. To facilitate reattachment of the door, push the hinge lever upward so the hinge pins remain recessed (see 2nd photo). 4 While pulling release knob, slide the fiber management tray out until it stops. Note: Removal of the set screw allows for the tray to be fully disengaged. 5 Connect both ends of the fiber jumper to equipment (active or passive). Estimate need- ed cable slack to allow tray to slide freely in and out of enclo- sure. Lace jumper into small cable management clips and main bend radius guide towers as shown. 6 Continue to coil jumpers around main bend radius towers and finish out of the enclo- sure using the small management rings. Route additional jumpers as shown in 2nd photo. 7 Allow sufficient exterior jumper slack to allow free movement of FSC3 sliding tray as well as the sliding tray of the interconnect cabinets, if applica- ble. 8 Rotate side grommet(s) to the open position and hold entering/ exiting patch cords as shown. Slide tray back into the FSC3. Rotate side grommet(s) to the closed position (see below). 9 Close enclosure doors. 10
Transcript of Fiber Storage Center (FSC3) Instructions -...
Fiber Storage Center (FSC3) Instructions
The fiber storage center(P/N: FSC3-(XX)) may bemounted to a 19” or 23” rack
depending on the orientation of themounting brackets. (19” positionshown.)Select one of the three sets ofmounting holes, based on front/rearclearance requirements, and securethe mounting brackets to each sideof the FSC3 using #10-32 screwsprovided.
1 Position the fiber storagecenter in the desired loca-
tion on the rack and secure withthe four (4) #12-24 screws andwashers provided.
Note: #10-32 screws and washers mayalso be used (not provided).
2
Open the front door bydepressing the latch locat-
ed at the upper center of the door.3 If required, remove the
door from the hinges bysqueezing the securing latchesinward until disengaged.To facilitate reattachment of thedoor, push the hinge lever upwardso the hinge pins remain recessed(see 2nd photo).
4 While pulling release knob,slide the fiber management
tray out until it stops.
Note: Removal of the set screw allowsfor the tray to be fully disengaged.
5 Connect both ends of thefiber jumper to equipment
(active or passive). Estimate need-ed cable slack to allow tray toslide freely in and out of enclo-sure. Lace jumper into small cablemanagement clips and main bendradius guide towers as shown.
6
Continue to coil jumpersaround main bend radius
towers and finish out of the enclo-sure using the small managementrings. Route additional jumpers asshown in 2nd photo.
7Allow sufficient exteriorjumper slack to allow free
movement of FSC3 sliding tray aswell as the sliding tray of theinterconnect cabinets, if applica-ble.
8 Rotate side grommet(s) tothe open position and hold
entering/ exiting patch cords asshown. Slide tray back into theFSC3. Rotate side grommet(s) tothe closed position (see below).
9 Close enclosure doors.10
© 2
007
Sie
mon
R
ev.
C
07/07
100.5
927
Fiber Storage Center (FSC3) Instructions
WARNING:Optical transmitters and fiber optic test equipment used in the
telecommunications industry uses invisible infrared energy.At sufficient power, this may cause eye or skin damage.
If you work with fiber optic products, including test equipment, consider the following:1. Do not look into fibers or connectors. They may be ‘live’.2. Know what is happening with the fiber under test at the far end!3. When connecting a light source, try to make it the last element you connect!4. Whenever possible, switch off and disconnect your light source(s) before breaking any
fiber connections.5. Always consider the hazard to other people:
a. Use warning signs, etc.b. Keep caps on unconnected fibers whenever possible.c. If using “live” optical beams, keep them low and facing away from personnel.
6. Don’t view optical outputs with a microscope, use a TV camera/monitor.7. Elect a safety officer to:
a. Train staffb. Maintain records of equipment classification, calibrations and safety checks.
8. Be careful of cut fibers. Remember they are sharp and difficult to see!
Global HeadquartersWatertown, Connecticut USA
Tel: (1) 866-548-5814
For a complete listing of our global offices visit our web site www.siemon.com
