CTU in Prague, Faculty of Mechanical Engineering DAF Page 1

Concentration factors

y

x

S

SK t

0

1

x

y

xG

Shape Factor orStress Concentration Factor ofan Elastic Stress

Relative Stress Gradient

CTU in Prague, Faculty of Mechanical Engineering DAF Page 2

http://mechanika.fs.cvut.cz/calculator.php

Concentration factors

15

2

R 4

2010

111

CTU in Prague, Faculty of Mechanical Engineering DAF Page 3

Concentration factors

https://www.efatigue.com/constantamplitude/stressconcentration/

CTU in Prague, Faculty of Mechanical Engineering DAF Page 4

Fatigue notch factor

0

100

200

300

400

500

600

1,E+03 1,E+04 1,E+05 1,E+06 1,E+07 1,E+08

Number of cycles [1]

Stre

ss a

mpl

itude

[MPa

]

smooth

notched

FL

FL,N

,

FLf

FL N

K

1t fK K q

Theoretically, if material has high notch sensitivity q

Fatigue notch factor

CTU in Prague, Faculty of Mechanical Engineering DAF Page 5

Fatigue notch factor, Kf and notch sensitivity factor, q

Experiments have shown that the effect of notches is less than that the estimated effect according a traditional stress concentration factor, Kt.

The fatigue notch factor, Kf , can be described as the effective stress concentration in fatigue.

This effect is dealt with using a notch sensitivity factor, q.

1 1f tK K q

Notch radius

CTU in Prague, Faculty of Mechanical Engineering DAF Page 6

Fatigue limit modifiing factors

Loading factor, kL

Historically, fatigue limits have been determined from simple bending tests where there is a stress gradient in the test specimen. A specimen loaded in tension will have a lower fatigue limit than one loaded in bending. An empirical correction factor, called the loading factor, is used to make an allowance for this effect.

Loading Type kLAxial 0.9

Bending 1.0Torsion 0.57

CTU in Prague, Faculty of Mechanical Engineering DAF Page 7

Fatigue limit modifiing factors

Surface finish factor, kSF

Fatigue limits are determined from small polished laboratory specimens. A surface finish correction is made to estimate the fatigue limit of the part with the actual surface finish

kSF

CTU in Prague, Faculty of Mechanical Engineering DAF Page 8

Fatigue limit modifiing factors

Size factor, kS

Experimentally, larger parts have lower fatigue limits than smaller parts. Since the materials data is obtained from small specimens, a correction factor, called the size factor, is used for larger diameters.

CTU in Prague, Faculty of Mechanical Engineering DAF Page 9

Fatigue limit modifiing factors

Size factor, kS

For non-circular sections an effective diameter is computed. The effective diameter is obtained by equating the volume of material subjected to 95% of the maximum stress to a round bar in bending with the same highly stressed volume

exp10

exp

mDDFL

S d dFL

Vk

V

y

x

S

CTU in Prague, Faculty of Mechanical Engineering DAF Page 10

Fatigue limit modifiing factors

Surface treatment factor, kT

CTU in Prague, Faculty of Mechanical Engineering DAF Page 11

Fatigue limit of a real part

Estimation of the fatigue limit of a real part

,FL L SF S T

FL Nf

k k k kK

1. CTU in Prague, Faculty of Mechanical Engineering 1. DAF 1. 1. Page 12

Safety factor of unlimited fatigue life (permanent strength)

1. Alternating stress (R=-1)• operational loading stress amplitude a

• fatigue limit of the real part in the critical cross section area FL,N

a

NFLn

,

100

1000

1.E+04 1.E+05 1.E+06 1.E+07

N [1]

a [M

Pa]

alloy steel

CTU in Prague, Faculty of Mechanical Engineering DAF Page 13

Example – Fatigue safe factor calculation

Railway axle

Material: alloy steel 24CrMo4, ASTM 4130

Point A of the potential crack initiation

Experimental strain amplitude measurement (in the point A):

Problem description:

,max 312 microstraina

A

CTU in Prague, Faculty of Mechanical Engineering DAF Page 14

Example – continuation http://fatiguecalculator.com

0,0762 1570 2ba f N N

0,07671570 2 10 437.5 MPaFL

CTU in Prague, Faculty of Mechanical Engineering DAF Page 15

Example – continuation http://fatiguecalculator.com

2.09tK

CTU in Prague, Faculty of Mechanical Engineering DAF Page 16

Example – continuation FEM Calculation – CTU Prague

1.95tK

Wheel

Braking disc

Axle

CTU in Prague, Faculty of Mechanical Engineering DAF Page 17

Example – continuation

1.95tK

1 1 1 2.0 1 0.83 1.83f tK K q

15

0

100

200

300

400

500

600

1,E+03 1,E+04 1,E+05 1,E+06 1,E+07 1,E+08

Number of cycles [1]

Stre

ss a

mpl

itude

[MPa

]

smooth

notched

FL

FL,N

CTU in Prague, Faculty of Mechanical Engineering DAF Page 18

Fatigue Limit

Estimation of the fatigue limit of a real part

,FL L SF S T

FL Nf

k k k kK

factor k value

loading kL 1.00

surface finish kSF 0.67

size factor kS 0.70

size factor kT 1.00

,437.5 1.00 0.67 0.70 1.00 112.1 MPa

1.83FL N

Example – continuation

CTU in Prague, Faculty of Mechanical Engineering DAF Page 19

Estimation of the nominal stress amplitude

Experimental strain amplitude measurement (in the point A):

,max 512 microstraina

A

206850 0.000312 64.5 MPaa E

Fatigue loadingExample – continuation

CTU in Prague, Faculty of Mechanical Engineering DAF Page 20

Safety factor

Estimation of the safety factor nFL

A 64.5 MPaa

Example – continuation

, 112.1 MPaFL N

0

100

200

300

400

500

600

1,E+03 1,E+04 1,E+05 1,E+06 1,E+07 1,E+08

Number of cycles [1]

Stre

ss a

mpl

itude

[MPa

]

smooth

notched

FL

FL,N

, 112.1 1.7464.5

FL NFL

a

n

CTU in Prague, Faculty of Mechanical Engineering DAF Page 21

Questions and problems II

.

1. What is difference between the shape factor and the notch factor? Write their definition equations.

2. Define the notch sensitivity factor of material and write equation for it (as a function of shape and notch factor).

3. Depends the stress concentration factor of metals on a material parameters? And what about of the notch factor?

4. What is the typical value of the stress concentration factor at a large tensile loaded plate with a round hole in the middle? Is the notch factor of such plate lower or higher as the shape factor?

5. Is the fatigue limit of a real part the same as the fatigue limit of a basic material? What other factors could be taken in the account by an expression of such fatigue limit?

6. What dimension of a shaft has higher the size factor ks ? Shaft with higher or smaller diameter?

CTU in Prague, Faculty of Mechanical Engineering DAF Page 22

Questions and problems II

.

Estimate the fatigue limit and the safety factor of the part on the Fig. 1. under harmonic loading.

The material of the part is steel 4130 bar Su= 778 MPasee http://fatiguecalculator.com/cgi-bin/StressShowMatProp.pl

Fig. 1

Other inputs:D= 50 mm outer diameterd= 30 mm inner diameterr= 5 mm notch radius

F= 40 kN maximum loading forceq= 0,8 1 notch sensitivity of the steelR= -1 stress ratio

n L= ? fatigue life safety factorN FL 2,00E+06 number of fatigue limit cyclesRa= 12,5 surface roughness

Example:

Solution

shape factor Kt= 1,71notch factor Kf= 1,57fatigue limit sFL= 7,95E+01safety factor nF= 1,40E+00