F-100
description
Transcript of F-100
![Page 1: F-100](https://reader034.fdocuments.in/reader034/viewer/2022051820/55cf9b1b550346d033a4c14a/html5/thumbnails/1.jpg)
1/4
F-100C interior S.A.
49 470
49 4701/48 scale detail set for kit • sada detailù pro model Trumpeter 1/48 Trumpeter
ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM
1.
2.28
33
30
26
27
32
H23, H37 4.
10
10
22
23
17
18
H23, H37
78
11
11142 pcs.
H23, H37
2929
24
25
3.
35
34
H23, H37
FE 470 + 49 470 F-100C interior
FILM
![Page 2: F-100](https://reader034.fdocuments.in/reader034/viewer/2022051820/55cf9b1b550346d033a4c14a/html5/thumbnails/2.jpg)
2/4 49 470
46
H20 H21
2
1
21
16
6
H32
44
45
film
H30
=
39
5
4
A1
?
=
40
5
4
A7
?
=
47
48
4
4
19
15
13
31
12
9
A5
32 pcs.
![Page 3: F-100](https://reader034.fdocuments.in/reader034/viewer/2022051820/55cf9b1b550346d033a4c14a/html5/thumbnails/3.jpg)
© EDUARD M.A. 2010 www.eduard.com Made in Czech Republic
eduardFor further detail sets look for 48 639 F-100C exterior(not included in this set)
3/4 49 470
OPEN CANOPY?=
A2
20
36
K1
37
43
41
38
42
A3
K8
eduardFor further detail sets look for 48 656 F-100C undercarriage(not included in this set)
16
2,8mm
G6, G7
2
G1
20
27
24 23- 0,3mm
H18 H19
![Page 4: F-100](https://reader034.fdocuments.in/reader034/viewer/2022051820/55cf9b1b550346d033a4c14a/html5/thumbnails/4.jpg)
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem pøilepíte, pøi pokusu o odlepení dojde k poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddìlujte od rámeèku na podkladovém papíøe. Po oddìlení je sejmìte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za èásti, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì manipulovat.
PARTS WITH GLUE DÍLY OPATØENÉ LEPIDLEM
4/4 49 470