ESSRBOND PG 101 · 2020. 12. 4. · BS 4254 10-20 5 hours Passed >300 ASTM D 412 Passed >120min No...
3
ESSRBOND PG 101 is a two component pourable, self leveling polysulphide resin based joint sealant. ESSRBOND PG 101 is specifically designed to be used as a watertight seal for moderate movement and control joints in horizontal areas. ESSRBOND PG has excellent adhesion to concrete, stone, metal and other common building surface. The cured sealant has good resistance to most environmental chemical & resists deterioration on prolonged exposure to UV. ESSRBOND PG 101 is suitable for use in horizontal areas with a maximum slope gradient of 10%. CHARACTERISTICS Ÿ High resilient with excellent recovery characteristics Ÿ Provides permanent and uniform watertight seal Ÿ Non- staining Ÿ Excellent resistance to fatigue and stays flexible throughout its service life won’t become brittle, caulk or crack due to UV exposure Ÿ Prevent uncontrolled cracking by allowing expansion and contraction during temperature changes Ÿ Excellent adhesion to most common building substrate ESSRBOND PG 101 2 Component Pourable Grade Polysulphide Joint Sealant DESCRIPTION Website: www.essrbond.com E-mail for enquiries : offi[email protected] E-mail for enquiries : [email protected] Ph No.: 7447766238 Ph No.: 7447478803 SR 3 CORPORATION - Vision Plus, office No,16-19 Near bhakti-shakti garden, Old Mumbai- Pune Highway, Nigdi, Pune- 411044(MH) INDIA Full Cure Standard Condition Color Chemical Resistance Solvent & Veg oils. Shrinkage Density [g/cc] 1.6 - 0.05 Pot life Shore ‘A’ Hardness Tack Free Time Elongation Water Potability Passes Cracking & Chalking after Heat Ageing70C InitialCure @ Standard Condition Application Temperature Service Temperature Movement Accommodation Factor (MAF) 7days Grey Ph.2.5 to 11.5 Hydrocarbon Fuels Negligible BS 4254 10-20 5 hours ASTM D 412 Passed >300 Passed >120min No Deterioration TT-S-0027E BS 6920 24 hours 25% +5 C to +40 C -20 C to +80 C TECHNICAL PROPERTIES: PROPERTIES RESULTS TEST METHODS ASTM C 531 ASTM D 543 ASTM D 792 ASTM D 2240 + - - - - - - - Ÿ Good resistance to ageing. Ÿ Retains joint soundness once cured Ÿ Resistance against mild chemicals, hydrocarbon fuels, sea water Ÿ Non-Toxic Can be used in potable water applications, swimming pools STANDARDS ESSRBOND PG 101 complies with the requirement of :BS EN ISO 11600:2003 (formerly BS 4254), BS 5212: Part 1,BS 6920 test on suitability with potable water Manufactured under ISO 9001 & ISO 14001 TDS No : SR 3- TDS-015 Rev No. 01 / Nov 2019
Transcript of ESSRBOND PG 101 · 2020. 12. 4. · BS 4254 10-20 5 hours Passed >300 ASTM D 412 Passed >120min No...
ESSRBOND PG 101 is a two component pourable, self leveling polysulphide resin based joint sealant. ESSRBOND PG 101 is specifically designed to be used as a watertight seal for moderate movement and control joints in horizontal areas. ESSRBOND PG has excellent adhesion to concrete, stone, metal and other common building surface. The cured sealant has good resistance to most environmental chemical & resists deterioration on prolonged exposure to UV. ESSRBOND PG 101 is suitable for use in horizontal areas with a maximum slope gradient of 10%.
CHARACTERISTICS
Ÿ High resilient with excellent recovery characteristics
Ÿ Provides permanent and uniform watertight seal
Ÿ Non- staining Ÿ Excellent resistance to fatigue and
stays flexible throughout its service life won’t become brittle, caulk or crack due to UV exposure
Ÿ Prevent uncontrolled cracking by allowing expansion and contraction during temperature changes
Ÿ Excellent adhesion to most common building substrate
ESSRBOND PG 101 2 Component Pourable Grade Polysulphide Joint Sealant
DESCRIPTION
Website: www.essrbond.comE-mail for enquiries : [email protected] for enquiries : [email protected]
Ph No.: 7447766238Ph No.: 7447478803
SR 3 CORPORATION - Vision Plus, office No,16-19 Near bhakti-shakti garden, Old Mumbai- Pune Highway, Nigdi, Pune- 411044(MH) INDIA
Full Cure Standard Condition
Color
Chemical Resistance Solvent & Veg oils.
Shrinkage
Density [g/cc] 1.6 - 0.05
Pot life
Shore ‘A’ Hardness
Tack Free Time
Elongation
Water Potability Passes
Cracking & Chalking after Heat Ageing70C
InitialCure @ Standard Condition
Application Temperature
Service Temperature
Movement Accommodation Factor (MAF)
7days
Grey
Ph.2.5 to 11.5 Hydrocarbon Fuels
Negligible
BS 4254
10-20
5 hours
ASTM D 412Passed >300
Passed >120min
No Deterioration TT-S-0027E
BS 6920
24 hours
25%
+5 C to +40 C
-20 C to +80 C
TECHNICAL PROPERTIES:
PROPERTIES RESULTS TEST METHODS
ASTM C 531
ASTM D 543
ASTM D 792
ASTM D 2240
+
--
-
----
Ÿ Good resistance to ageing. Ÿ Retains joint soundness once
curedŸ Resistance against mild chemicals,
hydrocarbon fuels, sea waterŸ Non-Toxic Can be used in potable
water applications, swimming pools
STANDARDS
ESSRBOND PG 101 complies with the r e q u i r e m e n t o f : B S E N I S O 11600:2003 (formerly BS 4254), BS 5212: Part 1,BS 6920 test on suitability with potable water Manufactured under ISO 9001 & ISO 14001
TDS No : SR 3- TDS-015Rev No. 01 / Nov 2019
BACK-UP MATERIAL
The backer rod will also provide resistance to sealant tooling pressure and help to attain proper wetting of substrate when the sealant is being tooled. The diameter of the backing rod shall be at least 20% larger but not greater than 33% of the joint width.CAUTION: Do not damage or poke holes in the backer rod dur ing of af ter installation, since this may cause air bubbles in the sealant and effect its performance.
MIXING & APPLICATION
ESSRBOND PG is supplied in pre-weighed two parts pack which requires on site mixing. Pour the hardener (part B) into the base (part A). Once the sealant has been installed a suitable rounded tool soaked in soapy water can be used to achieve an hour glass profile any masking tape app l ied shou ld be removed immediately after the sealant is installed.
PRIMING
Primer should be applied to clean, dry surface prior to the installation of backer rod or bond breaking tape. The joints edges shall be reprimed if the sealant installation is not carried out within 3 hours of application of the primer. For obtaining a clean neat finish, masking tape shall be applied on both the edges of the groove before applying the primer.
ESSRBOND PG 101
Website: www.essrbond.comE-mail for enquiries : [email protected] for enquiries : [email protected]
Ph No.: 7447766238Ph No.: 7447478803
SR 3 CORPORATION - Vision Plus, office No,16-19 Near bhakti-shakti garden, Old Mumbai- Pune Highway, Nigdi, Pune- 411044(MH) INDIA
2 Component Pourable Grade Polysulphide Joint Sealant
APPLICATION INSTRUCTIONS
JOINT PREPARATION
The joint surface must be clean, dry and free from oil, loose particles, cement and other contaminants which may affect the adhesion.
JOINT DESIGNS
The width of the joint should be a minimum of 4 times the anticipated movement. Joint with cyclic movement should have a wide to depth ratio of 2:1 for butt joint depth shall not exceed the width. the joint width and d e p t h s h o u l d b e m a i n t a i n e d a s recommended.Joint Width Ÿ 6mmŸ 50mmJoint depthŸ 6mmŸ 20mm for heavily trafficked floor joints
and areas exposed to hydrostatic pressure.
PACKING
ESSRBOND PG 101 : 1Kg ,4 Kg, 32 Kg
STORAGE
SHELF LIFE
HEALTH & SAFETY
Keep out of reach from children. Before handling, read both the product and material safety data sheet for detailed use and health information.
Store in a cool and dry place. Away from direct sunlight and moisture. Storage temperature to be below 35 C
1 2 m o n t h s f r o m t h e d a t e o f manufacturing in unopened condition.
LIMITATION
E S S R B O N D P G 1 0 1 i s n o t recommended for:Ÿ Vertical jointsŸ Movement joints having MAF >
25%Ÿ Damp and contaminated surfaceŸ Asphalt pavementsŸ Over painting (paint compatibility
with sealant shall be checked prior to painting) for joints> 50mm width
TDS No : SR 3- TDS-015Rev No. 01 / Nov 2019
ESSRBOND PG 101
Website: www.essrbond.comE-mail for enquiries : [email protected] for enquiries : [email protected]
Ph No.: 7447766238Ph No.: 7447478803
SR 3 CORPORATION - Vision Plus, office No,16-19 Near bhakti-shakti garden, Old Mumbai- Pune Highway, Nigdi, Pune- 411044(MH) INDIA
2 Component Pourable Grade Polysulphide Joint Sealant
25
Depth(mm) Width(mm)
6 10 15 20 25 30 40 50
6
10
15
20
30
27.7 16.5
10 6.5 5
4.4 3.3 2.6 2.2
2.5 2.0 1.6
1.6 1.3 1 0.8
1.1 0.83 0.66
COVERAGE
NOTE
The company’s product are sold subject to the company’s standard terms and conditions of sale product are warranted against defective materials & workmanship. The company makes every effort to ensure that all the information recommendations or to ensure that all the information, recommendations or the specifications provided by it are accurate and true. However as the company has no control over the conditions of use, it cannot accept any liability, either directly or indirectly regarding the usage of its product.
Length of joints in metres filled per litre of ESSRBOND PG 101
TDS No : SR 3- TDS-015Rev No. 01 / Nov 2019
![Wild Heart of the Seas- Birth of the Avenging Angel · BOPZS ]T 1]\bS\ba >`]Z]UcS 1VO^bS` =\S 1VO^bS` Be] 1VO^bS` BV`SS 1VO^bS` 4]c` 1VO^bS` 4WdS 1VO^bS` AWf 1VO^bS` ASdS\ 1VO^bS`](https://static.fdocuments.in/doc/165x107/60ae8a4c3fbde2177c4b2f1b/wild-heart-of-the-seas-birth-of-the-avenging-angel-bopzs-t-1bsba-zucs.jpg)
