ESC Three Phase IEC Low Voltage - maybomchinhhang.vn

Three phase sychronousESC Series Motors Enhanced performance cast iron units

3Editio

n

rd

ESC Three Phase IEC

Low Voltage

3Editio

n

rd

Product CatalogueProduct Catalogue

1

Introduction

ESC motors are suitable for driving various kinds of

machines or equiment. The output ratings are from

0.18KW to 355kW. The frame sizes are from 80 to 355.

ESC the motors have cast iron stator frame, endshields

and terminal boxes. The feet integrally cast into the stator

frame. The terminal box is mounted on the top as standard.

All motors comply with the requirements for European CE

marking.

Standard ESC series motors with the terminal box is

located on the top.The terminal box can be rotated through

4 positions, 90 part.

All motors are designed for high efficiency and low

temperature giving a long economical service life.

• Motors with terminal boxes on the right side or on the left

side are available.

• Motors from frame sizes 63 to 160 with aluminium stator

frames, terminal boxes and cast iron endshields are also

available.

Coolingandventilation

Enclosure

Voltageandfrequency

Connection

Noise

Vibration

The standard cooling method is totally Enclosed Fan Cooled

(TEFC) in accordance with code IC411 of IEC60034-6.

Standard motors in sizes 80-315 are equipped with radial-flow

plastic fans.

Standard motors in size 355 are equipped with radial-flow

aluminium fans.

The standard degree ofprotection is IP55.

The IP55 enclosure means complete hoseproof and dustproof

protection.

Ahigher degree ofprotection is available.

Standard voltages are 380V 50Hz or 425V 50Hz, but can be

wound for any single voltage in the range 200-600V at a

frequency 50 or 60 Hz.

The motors will operate satisfactorily with voltage variations of

±10% from the rated voltage.

Direct - on line starting can be used on all frame sizes. Motors up

to and including 2.2kW are star connected and cannot be started

with Star/Delt started.Motors above 2.2kWare delta staring.

The permitted noise levels of electrical machines are fixed in

IEC60034 - 9 (EN60034-9). The noise level of ESC motors is well

below this limit value.

Fordetails, please refer to the performance data tables.

Standard motors are designed to vibration class N (normal)

vibration class R (reduced) and vibration class S (special) are

available on request.

Stringent quality procedures are observed from first design to

finished products in accordance with ISO9001 documented

quality systems.Our factories have been assessed to meet these requirements, afurther assurance that only the highest possible standards ofquality are accepted.

Qualityassurance

Specification

General specification

ESC motors are built to comply with the requirements of the following international standards and regulation

1. International Electrotechnical commission - IEC 60034 and IEC 60072.

2. British Standards - BS5000 and BS 4999.

3. Australian Standards -AS 1359.

4. The requirements of European EC marking. Low voltage Directive 73/23 (1973). Modified by Directive 93/68 (1993) and the

EMC - Directive 89/336. These ESC motors are designed for use with other machinery, and they should only be used if the

complete machinery is in conformity with the provisions of the Directive of safety of machinery (89/93/EEC).

5. CEMEP agreement-all motors with standard rating include in this catalogue comply with efficiency class EFF2 and bear the

corresponding label on the rating plate. For efficiency data at 50%, 75% and full load, please refer to the performance data tables.

Motors comply with efficiency class EFF1 are available on request.

2

Standards IEC CENELEC BS

Methods of determining losses and efficiency

Degrees of protection

Methods of cooling

Mounting arrangements

Terminal markings and direction of rotation

Noise limits

Starting performance

Mechanical vibration

Standard voltages

Dimensions and output ratings

Mounting dimensions and relationshipframesizes-output ratings

Shaft dimensions

EN 60034-1

HD 53 2

EN60034-5

EN60034-6

EN60034-7

HD 53 8S4

EN60034-9

EN60034-12

EN60034-14

HD 472 S1

HD 231

HD 231

4999-14999-69

4999-34

4999-20

4999-21

4999-22

4999-3

4999-51

4999-112

4999-50

4999-1051-110

4999-10

Classification of environmental conditions

Insulation material

60034-1

60034-2

60034-5

60034-6

60034-7

60034-8

60034-9

60034-12

60034-14

60038

60072

60072

60072

600721-2-1

60085

General requirements for electrical machines

Standards and regulations

Foot mounting

3

Connection diagrams three phase motors with cage rotor

Standards and regulations

Against solar radiation

Degree of protection

IP standards explanation

Shaft

Finish

High solar radiation will result in undue temperature rise. In

these circumstances motors should be screened from solar

radiation by placement of adequate sunshades which do not

inhibit air flow.

Standard levels of enclosure protection for all ESC frame

sizes for both motor and terminal box is IP55, with IP56, IP65

and IP66 available on request. Enclosure designations

comply with IEC or AS60529. The enclosure protection

required will depend upon the environmental and operational

conditions within which the motor is to operate.

First characteristic numeral Degree of protection of persons

against approach to live parts or contact with live or moving

parts (other than smooth rotating shafts and the like) inside

the enclosure, and degree of protection of equipment within

the enclosure against the ingress of solid foreign bodies.

4 = Protected against solid object greater than 1.0 mm:

Wires or strips of thickness greater than 1.0 mm,

solid objects exceeding 1.0 mm

5 =Dust protected: Ingress of dust is not totally

prevented but it does not enter in sufficient

quantity to interfere with satisfactory operation

of the equipment.

6 = Dust tight: No ingress of dust.

Second characteristic numeral

4 = Protected against splashing water: Water

splashed against the enclosure from any

direction shall have no harmful effect.

5 = Protected against water jets: Water projected

by a nozzle against the enclosure from any

direction shall have no harmful effect.

6 = Protected against heavy seas: Water from

heavy seas or water projected in powerful jets

(larger nozzle and higher pressure than

second numeral 5) shall not enter the enclosure

in harmful quantities.

ESC motors have standard shaft extension lengths and are

provided with standard key, and drilled and tapped hole.

Non standard shaft extensions are available upon special

order, with shaft design outlined on a detailed drawing.

Shaft extension run out, concentricity and perpendicularity to

face of standard flange mount motors, comply with normal

grade tolerance as specified in IEC 60072-1 and AS1359.

Precision grade tolerance is available upon special order.

Standard ESC motor color is RAL 7044. Other colors are also

available. All castings and steel parts are provided with a

prime coat of rust-resistant paint.

The finishing coat of enamel paint is sufficient for normal

conditions, however special paint systems can be provided

to accommodate stringent requirements for motors in

corrosive environments. Special coatings are needed to

resist such substances as acid, salt water and extreme

climatic conditions.International protection rating prefix (IEC 60034 - 5)

First numeral

Second numeral

Electrical design

As standard, ESC motors have the following design and

operating parameters. Performance data is based on this

standard. Any deviation should be examined and

performance values altered in accordance with the

information provided in this section.

Three phase, 380V, 50Hz

Ambient cooling air temperature, 40°C

Altitude - 1000m Duty cycle S1 (continuous)

Rotatio - Clockwise viewed from drive end

Connection - 230 volt Delta/380 volt Star (3kW and below)

- 380 volt Delta/660 volt Star (4kW and above)

Standard ESC motors are designed for a power supply of

three phase 380V, 50Hz. Motors can be manufactured for any

supply between 100V and 1100V and frequencies other than

50Hz.

Standard ESC motors wound for a certain voltage at 50Hz can

Voltage and frequency

4

I P 5 5

1 2


Temperature and altitude

Rotation

Rated power specified in the performance data tables apply

for standard ambient conditions of 40°C at 1000m above sea

level. Where temperature or altitude differ from the

standard, multiplication factors in the table below should

be used.

Effective Power required = 15kW

Air temperature = 50°C (factor 0.93)

Altitude = 2500 metres (factor 0.91)

The appropriate motor is one with a rated power above the

required, being 18.5kW.

For clockwise rotation, viewed from drive end, standard

three phase ESC motor terminal markings coincide with

the sequence of the phase line conductors.

For counter clockwise rotation, viewed from drive end, two of

the line conductors have to be reversed. This is made clear

in the accompanying table.

Example 1

Example 2

Rated power = 11kW

Air temperature = 50°C (factor 0.93)

Altitude = 1500 metres (factor 0.98)

Effective Power = 11 x 0.93 x 0.98 = 10.0kW

5

Rated power

required=

15= 17.7kW

0.93 x 0.91

also operate at other voltages at 50Hz and 60Hz without

modification, subject to the changes in their data .

Not applicable for motors with F class temperature rise.

* Note: This table is not applicable for hazardous area motors

1) N = Full load current TN = Full load torque

I /I =Locked rotor current/ full load current

T /T =Locked rotor torque/ full load torque

T /T = Breakdown torque/full load torque

Standard torque values for alternative supplies are

obtainable only with special windings. For these

purpose-built motors the performance data is the same

as for 380V motors except for the currents which are

calculated with the accompanying formula:

Where:

I = Current

I = Full load current at 380 volt

U = Design voltage

*

L N

L N

B N

X

N

X

IX

=

380 x

UX

IN

Motor

wound

for 50Hz

at rated

voltage -

Connected

to

Data in percentage of values at 50Hz and

rated voltage

Output r/min I /IN N

IL

TN

T /TL N

T /TB N

380V

400V

415V

525V

400V

380V

400V

415V

440V

460V

380V

415V

400V

415V

440V

460V

480V

380V

400V

440V

415V

440V

460V

480V

550V

525V

550V

575V

600V

50Hz

60Hz

60Hz

60Hz

60Hz

60Hz

50Hz

50Hz

60Hz

60Hz

60Hz

60Hz

60Hz

50Hz*

50Hz

50Hz

60Hz

60Hz

60Hz

60Hz

50Hz

60Hz

60Hz

60Hz

60Hz

100

100

105

110

115

120

100

100

100

104

110

115

120

100

100

100

100

105

110

115

100

100

105

110

115

100

120

120

120

120

120

100

100

120

120

120

120

120

100

100

100

120

120

120

120

100

120

120

120

120

95

98

98

98

100

100

105

96

98

98

98

100

100

109

104

94

98

98

98

100

95

98

98

98

100

110

83

90

95

100

105

91

108

83

89

95

100

105

84

93

112

83

90

95

100

110

83

90

95

100

100

83

87

91

96

100

100

100

83

86

91

96

100

100

100

100

83

87

91

96

100

83

87

91

96

110

70

80

85

95

100

90

108

70

75

85

93

100

84

93

112

70

80

85

95

110

70

80

85

95

110

85

90

93

98

103

90

108

85

88

93

98

103

84

93

112

85

90

94

98

110

85

90

94

98

Power=

Powerx

Factorx

Effective Rated Temperature Altitude

Factor

Ambient

temperature

Temperature

factor

Altitude above

sea level Altitude factor

30°C 1.06 1000m 1.00

35°C 1.03 1500m 0.98

40°C 1.00 2000m 0.94

45°C 0.97 2500m 0.91

50°C 0.93 3000m 0.87

55°C 0.88 3500m 0.82

60°C 0.82 4000m 0.77


DutyESC motors are supplied suitable for S1 operation (continuous operation under rated load). When the motor is to operate

under any other type of duty the following information should be supplied to determine the correct motor size:

• Type and frequency of switching cycles as per duty factors S3 to S7 and duty cycle factor.

• Load torque variation during motor acceleration and braking (in graphical form).

• Moment of inertia of the load on the motor shaft.

• Type of braking (eg mechanical, electrical through phase reversal or DC injection).

Permissible output

Connection

Internal connections, voltages andVF drive selection

Apply the factors in the accompanying table to the output

rating for motors with duty cycles that are not continuous.

For other duties (S4, S5, S6 and S7) contact ESC for

appropriate duty cycle factors.

A motor’s rated voltage must agree with the power supply

line-to-line voltage. Care must therefore be taken to ensure

the correct connection to the motor terminals.

Standard terminal connections for motors 3kW and below is

220V delta / 380V star. These motors are designed for 380V

Direct On Line (D.O.L.) starting, when connected in the star

configuration. They are also suitable for operation with 220V

three phase variable frequency drives. when connected in

the delta configuration. Standard terminal connections for

motors 4kW and above is 380V delta / 660V star. These

motors are designed for 380V Direct On Line (D.O.L.)

starting, when connected in the delta configuration. They

are also suitable for operation with 380V three phase

variable frequency drives. Alternatively they can be

operated D.O.L. in the star configuration from a 660V supply

or with a 660V variable frequency drive.

In this case the drive must be supplied with an output reactor

to protect the winding insulation. These size motors are also

suitable for 380V tar-delta starting as described below.

Motor connected for D.O.L. starting with bridges in place for

star connection ( 3kW and below)

Poles

Duty cycle factor

For frames

80 to 132

For frames

160 to 250

For frames

280 to 355

Short-time duty, S2

30 min 2 1.05 1.20 1.20

4 to 8 1.10 1.20 1.20

60 min 2 to 8 1.00 1.10 1.10

Intermittent duty, S3

15% 2 1.15 1.45 1.40

4 to 8 1.40 1.40 1.40

25% 2 1.10 1.30 1.30

4 to 8 1.30 1.25 1.30

40% 2 1.10 1.10 1.20

4 to 8 1.20 1.08 1.20

60% 2 1.05 1.07 1.10

4 to 8 1.10 1.05 1.10

380 Volt

6

Symbol

Type

S1 Operating time Continuous

S2 Operating time 0.5; 1; 3; 5; 10; 30; 60; 90 mins

S3 S6 Period of one cycle 10 mins

S4 S5 S7 S8 Switching rate 60, 90, 120, 240, 600 c/h

S3 S4 S5 S6 Relative on period 15%; 25%; 40%, 60%

S4 S5 S7 S8 moment of inertia factor F1 1.2; 1.6; 2.5; 4

Design data

Preferred value


Motor connected for D.O.L. starting with bridges in place for

delta connection (4kW and above).

All of the following starter options are available through

ESC Drives division, and are best supplied together with the

motor.

When an electric motor is started by direct connection

to the power supply (D.O.L.), it draws a high current,

called the ‘starting current’, which is approximately equal

in magnitude to the locked rotor current I . As listed in

the performance data, locked rotor current can be up

to 8 times the rated current I of the motor. In circumstances

where the motor starts under no load or where high starting

toque is not required, it is preferable to reduce the starting

current by one of the following means.

ESC motors 3.0kW and above are suitable for thestar-delta starting method. Through the use of astar-delta starter, the motor terminals are connected in thestar configuration during starting, and reconnected to thedelta configuration when running.

The benefits of this starting method are a significantly lower

starting current, to a value about 1/3 of the D.O.L. starting

current, and a corresponding starting torque also reduced

to about 1/3 of its D.O.L. value. It should be noted that a

second current surge occurs on changeover to the delta

connection. The level of this surge will depend on the speed

the motor has reached at the moment of change over.

Variable Voltage Variable Frequency drives are primarily

recognized for their ability to manipulate power from a

constant 3 phase 50/60Hz supply converting it to variable

voltage and variable frequency power. This enables the

speed of the motor to be matched to its load in a

flexible and energy efficient manner. The only way of

producing starting torque equal to full load torque with

full load current is by using VVVF drives. The functionally

flexible VVVF drive is also commonly used to reduce

energy consumption on fans, pumps and compressors and

offers a simple andrepeatable method of changing speeds

or flow rates.

Capacitive voltages in the rotor can be generated due to an

effect caused by harmonics in the waveform causing voltage

discharge to earth through the bearings. This discharge

results in etching of the bearing running surfaces. This effect

is known as Electrical Discharge Machining (EDM). It can be

control with the fitment of appropriate filters to the drive.

To futher reduce the of EDM, an insulated non drive bearing

can be used. ESC recommends the use of insulated

bearings for all motors 315 frame and above.

Starting

EDM Concerns

D.O.L Starters

Star - delta starting

VVVF Drives

L

N

380 Volt

110

100

90

80

70

60

50

40

30

20

10

0

5 10 15 20 25 30 35 40 45 50 55 60 65 70 75

Torq

ue (

% o

f ra

ted)

Frequency (Hz)

7


8

Insulation

Thermal protection

Speed at partial loads

Torque characteristics

The insulation system is Class F (150K) and the motors are

designed to operate with Class B (80K).

This ensures long life and reliability with the ability to

withstand ambient temperatures as high as 54 C or up to

15% overload in adverse electrical supply situations.

Non-Standard ESC will provide a safety margin of 45K and

can be safely operated at elevated ambient temperatures.

Due to their conservative design many sizes in the ESC

range of motors have temperature rises considerably

less than 80K and therefore provide even greater

safety margins.

Motors can be protected against excessive

temperature rise by inserting, at various positions within

the windings, thermal probes which can either give a

warning signal or cut off the supply to the motor in the event

of a temperature abnormality.

The units fitted to ESC motors, frame sizes 160 and above,

are PTC thermistors. These thermovariable resistors, with

positive temperature co-efficient, are fitted one per phase,

series connected and are terminated in a terminal

strip located in the terminal box. Trip temperature is

160°C (180°C for ESC series). Additional 130°C

thermistors can be fitted as an option for alarm connection.

The relationship between motor speed and degree of

loading on an ESC motor is approximately linear up

to the rated load. This is expressed graphically in

the accompanying drawing.

Where:

n = full load speed

n = synchronous speed

P/P = partial load factor

Current at partial loads can be calculated using the

following formula:

Where:

I = partial load current (amps)

Pout = partial load (kW)

U = rated voltage

cos = partial load power factor

= partial load efficiency (%)

Typical characteristics of torque behaviour relative to

speed are shown in the torque speed curve example

below.

Where:

T = full load torque

T = locked rotor torque

T = pull-up torque

T = break down torque

n = full load speed

n = synchronous speed

ESC motors all exceed the minimum starting torque

requirements for Design N (Normal torque) as specified

in IEC60034-12, and in most cases meet the

requirements of Design H (High torque). Rated torque

can be calculated with the following formula:

Where:

T = full load torque (Nm)

P = full load output power (kW)

n = full load speed (r/min)

0

N

S

N

X

X

N

X

X

N

L

U

B

N

S

N

N

N

Current at partial loads

φ

η

Insulation class

B F H

Max. permissible winding temp. (°C) 130 155 180

Less ambient temp. (°C) -40 -40 -40

Less hotspot allowance (K) -10 -10 -15

Equals max. permissible temp.rise (K) 80 150 125

Less max. design temp. rise (K) -80 -80 -80

Equals min. safety margin (K) - 25 45

I =x

Poutx x 105

3 x U X XN XcosφX η

pN

TN

=9950 x

nN

Load Torque


9

3000r/min = 2 poles

2 Pole - 3000 rpm synchronous speed 50Hz

0.75

1.1

1.5

2.2

3

4

5.5

7.5

11

15

18.5

22

30

37

45

55

75

90

110

132

160

200

280

315

5.5

11

75

110

100 75 50

Efficiency %

at % full loadFull load I , 50HzN

380V 400V 415V

Current

(A) (A) (A)

Locked

rotor

I /IL N

Moment

of inertia

(kg m )

J=1/4 GD

x

2

2

Nosie

level

at1meter

dB(A)

Net

weight

(kg)

Locked

rotor

T /TL N

Pull

up

T /TU N

Break

down

T /TB N

Torque

Full

load

T

(Nm)N

Output

(kW)

Full

lock

speed

(rpm)

100 75 50

power factor, cos

at % full load

φFrame

Size

High Output Design*

* The motor is increased output (kW) in a reduced frame size electric motor.

220

250

2840

2840

2850

2850

2880

2880

2900

2900

2930

2930

2930

2940

2950

2950

2970

2970

2970

2970

2980

2980

2880

2910

2970

2980

2980

2980

2980

2980

2980

2980

1.80

2.60

3.40

4.80

6.30

8.30

11.1

14.9

21.1

28.6

34.6

41.0

55.4

67.9

82.1

99.6

134.8

159.5

194.6

233

282.1

347.7

11.1

21.4

135.1

194.7

478

537

379

429

1.70

2.50

3.20

4.60

6.00

7.90

185

128.4

20.4

10.5

270

330.1

221.4

184.9

151.5

128.1

10.5

14.2

20.1

94.6

78.0

64.5

52.6

38.9

32.9

27.2

510

457

361

408

1.67

2.40

3.10

4.40

5.80

7.60

10.2

13.5

19.4

26.2

31.8

37.6

50.7

62.2

75.3

91.3

123.5

146.1

178.2

213.4

258.4

318.4

437

491

10.2

19.7

123.8

178.3

349

393

6.5

6.5

6.2

7.7

5.5

5.6

6.1

6.1

6.5

6.5

6.9

6.9

6.7

6.7

6.7

6.7

6.6

6.6

6.7

6.7

6.8

6.8

6.5

6.5

6.6

6.8

5.46

6.69

5.42

5.74

75.5

76.1

79.5

81.7

83.1

83.5

85.9

87.2

88.7

89.5

90.2

90.6

91.5

92.0

92.5

93.2

93.9

94.2

94.4

94.6

94.7

95.0

95.6

95.7

94.3

85.7

88.4

93.7

95.5

95.6

74.8

75.8

78.8

80.3

82.6

84.1

85.7

86.9

87.2

89.5

93.9

93.4

88.0

85.4

89.3

90.1

90.1

91.6

90.9

92.9

93.2

93.9

93.7

94.4

94.2

94.5

94.9

95.1

95

94.9

72.3

73.1

76.7

78.6

81.3

83.3

84.4

84.7

86.1

88.6

88.4

89.4

87.0

88.1

88.4

92.9

84.6

83.8

51.9

94.0

93.0

93.6

93.0

93.0

92.3

92.5

91.2

90.1

94.1

93.0

0.83

0.84

0.85

0.85

0.87

0.88

0.88

0.88

0.89

0.89

0.90

0.90

0.90

0.90

0.90

0.88

0.88

0.90

0.91

0.90

0.90

0.91

0.91

0.91

0.91

0.92

0.92

0.93

0.92

0.92

0.79

0.81

0.81

0.81

0.83

0.84

0.85

0.84

0.85

0.80

0.87

0.87

0.88

0.92

0.93

0.91

0.91

0.90

0.89

0.88

0.89

0.87

0.90

0.89

0.87

0.89

0.87

0.87

0.91

0.91

0.66

0.68

0.70

0.71

0.73

0.78

0.78

0.79

0.81

0.83

0.81

0.79

0.83

0.90

0.82

0.82

0.84

0.83

0.85

0.81

0.82

0.86

0.83

0.86

0.87

0.89

0.88

0.90

0.89

0.88

2.5

3.7

5.0

7.4

10.0

13.3

18.1

24.5

35.8

97.2

71.4

60.4

48.8

13.3

36.2

241

354

1010

641

513

423

353

290

241

177

145

119.8

705

897

802

2.7

2.2

2.3

2

2.3

2.3

2.5

2.7

2.7

2.6

2.3

2.5

2.6

2.6

2.5

2.6

2.5

2.4

2.4

2.5

2.4

2.4

2.0

2.1

1.9

1.9

2.01

1.61

1.48

1.65

1.9

2.4

2.1

2.0

1.8

2.0

2.1

2.3

2.5

2.2

2.0

2.3

2.2

2.1

2.0

2.1

2.2

2.0

2.2

1.8

1.9

1.9

1.7

1.9

1.7

1.7

1.6

1.5

1.31

1.40

2.6

2.6

2.9

2.9

2.9

2.9

2.6

2.8

2.9

2.4

3.2

3.2

2.5

2.9

2.8

2.8

2.7

2.6

2.6

2.8

2.7

2.7

2.5

2.5

2.4

2.4

2.76

2.29

2.34

2.44

67

67

72

72

76

77

78

83

94

96

80

80

86

86

89

89

92

92

92

93

94

94

96

96

99

99

103

103

103

103

42

72

440

546

13

15

20

23

30

40

54

60

99

110

127

167

220

242

281

373

477

516

792

828

932

1044

1798

1834

1490

1638

0.0008

0.0009

0.0012

0.0014

0.0039

0.0055

0.0109

0.013

0.038

0.045

0.055

0.076

0.124

0.139

0.233

0.312

0.597

0.675

1.18

1.55

1.76

4.1

0.007

0.028

0.412

0.86

2.02

3.91

3.21

3.56

80M1

80M2

90S

90L

100L

112M1

132S1

132S2

160M1

160M2

160L

180M

200L1

200L2

225M

250M1

280S

280M1

315S

315M

112M2

132M

250M2

280M2

315L1

315L2

355L1

355L2

355M1

355M2

Performance data

10


High Output Design*


1500r/min = 4 poles

11

75

315

355

110

0.55

0.75

1.1

1.5

2.2

3

4

5.5

7.5

11

15

18.5

22

30

37

45

55

90

132

160

110

75

200

250

220

280

132M2

250M2

280M2

80M1

80M2

90S

90L

100L1

100L2

112M

132S

132M1

160M

160L

180M

180L

200L

225S

225M

250M1

280M1

280S

315M

315L1

315L2

355M2

315S

355M1

355L2

355L

355L1

1480

1480

1480

1490

1490

1490

1440

1480

1480

1390

1390

1400

1400

1420

1420

1440

1440

1440

1460

1460

1470

1470

1470

1480

1480

1480

1480

1480

1480

1490

1490

240

287

358

554

620

22.6

138.4

201

1.60

2.10

2.90

3.80

5.10

6.80

8.80

11.7

15.6

22.5

30.3

36.2

42.9

57.5

69.7

84.5

103

165

200.5

138.1

388

440

492

228

272.7

340.1

420

521

592

21.5

131.5

191

1.50

2.00

2.80

3.60

4.80

6.50

8.40

11.1

14.8

21.4

28.8

34.4

40.8

54.6

66.2

80.3

97.9

156.8

190.5

131.2

372

471

219.8

262.8

327.8

506

567

20.7

126.7

184

1.40

1.90

2.70

3.50

4.70

6.20

8.10

10.7

14.3

20.6

27.7

33.1

39.3

52.7

63.8

77.4

94.3

151.1

183.6

126.5

356

403

450

6.8

6.6

6.4

6.2

6.5

6.8

5.5

5.6

5.4

5.2

6.0

6.1

6.5

6.8

6.5

6.9

6.8

6.4

6.9

6.8

6.5

6.3

6.4

6.9

6.5

6.8

6.05

6.44

6.21

6.18

6.17

95.0

95.2

95.4

95.6

95.7

95.8

88.4

93.6

94.5

71.4

73.5

76.2

78.7

81.0

82.7

84.5

85.7

87.1

88.6

89.5

90.2

90.7

92.1

92.7

93.0

93.3

94.1

94.7

93.8

95.6

95.7

70.9

73.2

75.9

78.3

80.7

82.3

84.0

85.2

86.5

87.6

88.5

89.6

90.2

91.5

92.1

92.4

92.6

93.8

93.9

93.3

94.3

94.4

94.6

94.8

95.6

95.7

87.9

93.4

94.0

94.8

95.6

93.0

93.3

93.6

93.3

94.4

94.6

86.5

91.4

91.9

68.9

71.4

74.6

76.6

79.6

80.9

81.9

83.9

84.5

86.5

87.2

88.1

88.0

88.8

90.3

90.3

90.4

91.6

91.9

91.6

93.8

94.4

0.88

0.89

0.89

0.90

0.90

0.91

0.84

0.88

0.89

0.75

0.76

0.77

0.78

0.81

0.82

0.82

0.83

0.84

0.84

0.85

0.86

0.86

0.86

0.87

0.87

0.87

0.88

0.88

0.88

0.90

0.90

0.88

0.86

0.87

0.89

0.87

0.88

0.79

0.87

0.87

0.67

0.66

0.66

0.70

0.71

0.76

0.75

0.77

0.79

0.82

0.82

0.82

0.83

0.83

0.85

0.84

0.84

0.87

0.88

0.87

0.86

0.87

0.83

0.81

0.78

0.87

0.85

0.86

0.71

0.82

0.82

0.55

0.55

0.52

0.58

0.58

0.64

0.66

0.68

0.70

0.76

0.75

0.72

0.74

0.78

0.76

0.78

0.78

0.81

0.86

0.83

0.79

0.85

73

483.9

709.8

3.8

5.2

7.5

10.2

14.8

20.2

26.5

36.5

49.8

72.0

98.2

120.2

143

195

238.9

290.5

851.8

355.1

580.7

709.8

483.9

2275

1032

1290

1603

2020

1410

1795

2.3

2.6

2.2

2.1

2.2

2.3

2.1

2.2

2.2

2.2

2.4

2.3

2.3

2.3

2.3

2.4

2.3

2.3

2.3

2.3

2.4

2.2

2.3

2.2

2.2

1.9

2.1

1.93

1.94

2.17

2.01

75

427

830

2083

13

15

20

24

29

32

42

57

69

918

107

129

162

172

224

277

302

383

548

850

527

1018

1122

1650

1804

1592

1758

1.7

1.6

1.8

1.8

1.6

1.8

1.8

1.9

1.8

2.0

1.9

2.0

2.1

2.0

2.1

1.9

2.0

2.1

1.9

2.1

2.0

1.9

1.8

1.6

1.8

1.9

1.7

1.8

1.8

1.7

1.6

3.2

2.8

3.0

2.7

2.6

2.3

2.4

2.4

2.5

2.6

2.6

2.7

2.8

2.9

3.0

2.9

2.9

2.9

2.9

2.9

2.7

2.5

2.5

2.7

2.7

2.8

2.33

2.42

2.32

2.41

2.35

7.9

0.057

0.88

2.68

0.002

0.002

0.002

0.003

0.007

0.007

0.0095

0.0214

0.0296

0.0075

0.0092

0.139

0.158

0.262

0.406

0.469

0.66

1.46

1.12

3.29

3.79

4.49

5.67

6.66

3.11

5.28

6.17

58

58

61

61

64

64

65

71

71

75

75

76

76

79

81

90

97

97

101

101

101

75

86

93

81

83

86

86

93

101

101

100 75 50

Efficiency %


380V 400V 415V

Current

(A) (A) (A)

Locked

rotor

I /IL N

Moment

of inertia

(kg m )

J=1/4 GD

x

2

2

Nosie

level

at1meter

dB(A)

Net

weight

(kg)

Locked

rotor

T /TL N

Pull

up

T /TU N

Break

down

T /TB N

Torque

Full

load

T

(Nm)N

Output

(kW)

Full

lock

speed

(rpm)

100 75 50

power factor, cos

at % full load

φFrame

Size

Performance data

11


1000 r/min = 6 poles

High Output Design*


0.37

0.55

0.75

1.1

1.5

2.2

3

4

5.5

7.5

11

15

18.5

22

30

37

45

75

90

55

75

110

132

160

185

200

250

220

280

890

890

910

910

920

940

960

960

960

970

970

970

970

970

980

980

980

985

990

990

990

990

990

990

990

990

990

990

990

1.30

1.80

2.3

3.20

4.10

5.60

7.20

9.70

12.8

17.1

24.5

31.6

38.5

44.7

59.3

70.1

86.0

140

105

142

170

206

244

291

448

335

361

395

501

1.20

1.70

2.20

3.00

3.90

5.30

7.00

9.20

12.2

16.2

23.3

30.0

36.6

42.5

56.3

66.6

81.7

99.8

134.9

161.5

195.7

231.8

133

275

342

317

376

425

477

1.20

1.60

2.10

2.90

3.80

5.10

6.80

8.90

11.7

15.7

22.4

28.9

35.3

40.9

54.3

64.2

78.7

96.1

130

155.7

188.6

223.4

267

330

409

128.2

306

365

460

4.4

4.5

4.1

4.6

5.0

5.2

5.6

6.2

6.5

5.6

5.8

5.7

6.7

6.6

6.8

6.2

6.1

6.7

6.5

6.2

6.0

5.8

5.8

7.13

7.09

6.59

6.94

5.90

6.32

62.5

65.0

69.1

72.0

76.0

79.1

81.3

82.3

84.7

86.6

87.6

89.0

90.2

90.2

91.5

92.2

92.5

92.9

94.4

93.9

94.5

94.6

95.4

95.5

95.6

93.6

95.4

95.5

95.6

61.4

64.7

68.7

71.6

76.6

78.6

80.8

81.9

84.3

86.1

87.1

88.4

90.0

89.8

91.0

91.9

92.2

92.5

93.6

93.5

94.2

94.3

95.0

96.2

95.1

93.0

95.0

95.0

95.1

55.2

63.0

65.6

69.5

73.1

76.5

77.8

79.5

82.0

83.6

85.2

86.3

87.4

87.6

88.1

89.3

89.4

90.4

91.7

91.6

92.3

92.3

93.1

94.1

92.9

91.6

93.1

92.8

92.9

0.70

0.72

0.72

0.73

0.75

0.76

0.76

0.76

0.77

0.77

0.78

0.81

0.81

0.83

0.84

0.86

0.86

0.86

0.86

0.86

0.86

0.87

0.87

0.88

0.89

0.87

0.88

0.88

0.89

0.63

0.62

0.65

0.66

0.73

0.67

0.67

0.67

0.68

0.74

0.76

0.77

0.78

0.80

0.82

0.81

0.83

0.86

0.84

0.84

0.85

0.87

0.87

0.85

0.86

0.83

0.88

0.85

0.86

0.50

0.53

0.56

0.52

0.56

0.59

0.54

0.56

0.55

0.68

0.67

0.63

0.69

0.71

0.76

0.75

0.76

0.81

0.80

0.77

0.82

0.81

0.83

0.81

0.82

0.77

0.84

0.81

0.82

0.002

0.003

0.003

0.004

0.007

0.014

0.029

0.036

0.045

0.088

0.116

0.207

0.315

0.36

0.547

0.834

3.21

1.39

1.65

4.11

4.28

5.45

6.12

8.85

9.55

9.13

10.05

10.3

10.8

82

54

54

57

57

61

65

69

69

69

73

73

73

76

76

76

78

80

80

85

85

85

85

92

92

92

92

92

92

15

16

21

23

29

37

52

59

72

98

121

164

208

217

287

355

456

502

786

884

964

1060

1554

1768

1902

630

1620

1796

1962

280M2

80M1

80M2

90S

90L

100L

112M

132S

132M1

132M2

160M

160L

180L

200L1

200L2

225M

250M

280S

280M1

315S

315M

315L1

315L2

355M1

355M3

355L2

355M2

355L1

355L

4.0

5.9

7.9

11.5

15.6

22.4

29.9

39.8

54.7

73.9

108

148

182

217

293

361

438

536

724

869

727

1062

1274

1544

1930

1785

2413

2122

2701

1.9

2.1

2.3

2.3

2.4

2.1

1.9

2.1

2.3

2.0

2.1

2.0

2.2

2.3

2.2

2.0

1.9

2.1

2.0

2.0

1.9

2.0

2.28

2.3

2.16

2.1

2.24

1.84

2.08

2.3

2.4

2.7

2.7

2.8

2.5

2.5

2.7

2.8

2.6

2.4

2.4

2.8

2.9

2.7

2.5

2.5

2.7

2.7

2.6

2.7

2.7

2.3

2.95

2.89

2.64

2.84

2.73

2.52

1.8

1.6

1.9

1.7

1.8

1.8

1.7

1.9

1.7

1.7

1.6

1.8

1.7

1.6

1.9

1.6

1.8

1.8

1.7

1.4

1.5

1.4

1.6

1.6

1.8

1.7

1.4

1.6

1.6

100 75 50

Efficiency %


380V 400V 415V

Current

(A) (A) (A)

Locked

rotor

I /IL N

Moment

of inertia

(kg m )

J=1/4 GD

x

2

2

Nosie

level

at1meter

dB(A)

Net

weight

(kg)

Locked

rotor

T /TL N

Pull

up

T /TU N

Break

down

T /TB N

Torque

Full

load

T

(Nm)N

Output

(kW)

Full

lock

speed

(rpm)

100 75 50

power factor, cos

at % full load

φFrame

Size

Performance data

12


750 r/min = 8 poles

0.18

0.25

0.37

0.55

0.75

1.1

1.5

2.2

3

4

5.5

7.5

11

15

18.5

22

30

37

45

55

75

90

110

132

160

200

185

220

630

640

660

660

690

690

690

710

710

720

720

720

730

730

730

740

740

740

740

740

740

740

740

740

740

740

740

740

0.88

1.15

1.48

2.16

2.41

3.35

4.4

5.90

7.80

10.2

13.6

17.7

25.4

34.0

41.0

47.2

63.3

77.5

94.1

110.8

150.1

177.4

216.4

259

315

393

363

425

0.84

1.09

1.41

2.05

2.29

3.18

4.20

5.60

7.40

9.70

12.9

16.8

24.1

32.3

39.0

44.8

60.1

73.6

89.4

105.3

142.6

168.5

205.6

246

298

370

342

410

0.81

1.05

1.36

1.98

2.21

3.07

4.00

5.40

7.10

9.30

12.5

16.2

23.3

31.1

37.5

43.2

58.0

71.0

86.2

101.5

137.4

162.4

198.1

240

292

361

334

390

2.9

3.0

3.4

3.5

3.5

3.6

3.9

4.3

4.4

4.4

5.0

5.7

5.6

5.5

5.6

5.4

5.3

5.6

5.2

5.7

5.9

6.2

6.0

5.03

5.28

5.42

5.29

4.76

51.2

54.2

62.21

63.1

70.5

72.4

74.5

79.3

80.1

81.6

83.3

85.9

87.8

88.3

90.2

90.8

91.2

91.8

92.0

93.1

93.7

94.0

94.2

94.6

94.7

94.8

94.8

94.8

46.5

49.2

61.3

62.5

70.0

71.9

74.0

78.7

79.8

81.1

82.9

85.6

87.4

88.0

89.8

90.4

90.9

91.3

91.5

92.9

93.4

93.6

93.8

94.5

94.5

94.6

94.6

94.6

38.9

39.3

54.6

55.8

63.6

69.5

72.0

77.6

78.1

79.7

81.7

83.7

85.5

86.3

87.8

88.3

88.9

88.8

89.4

91.3

91.9

92.1

92.4

91.9

92.2

92.3

92.3

92.3

0.61

0.61

0.61

0.61

0.67

0.69

0.70

0.71

0.73

0.73

0.74

0.75

0.75

0.76

0.76

0.78

0.79

0.79

0.79

0.81

0.81

0.82

0.82

0.82

0.81

0.82

0.82

0.83

0.56

0.55

0.54

0.53

0.53

0.57

0.62

0.64

0.64

0.66

0.66

0.68

0.69

0.72

0.72

0.75

0.76

0.75

0.74

0.77

0.78

0.76

0.80

0.79

0.78

0.81

0.79

0.82

0.47

0.47

0.45

0.43

0.44

0.46

0.49

0.53

0.52

0.57

0.55

0.55

0.58

0.62

0.65

0.66

0.68

0.66

0.65

0.70

0.70

0.70

0.71

0.71

0.72

0.75

0.73

0.76

2.8

3.7

5.4

8.0

10.4

15.2

20.8

29.6

40.4

53.1

73.0

99.5

144

196.3

242.1

284

387.3

477.7

581

710.1

968.3

1162

1420

1704

2066

2582

2388

2839

2.0

2.1

2.0

2.1

2.0

2.2

2.4

2.3

2.2

2.2

2.2

2.1

2.3

2.1

2.2

2.1

2.2

2.3

2.1

1.9

2.1

2.3

2.2

1.86

2.03

2.12

2.04

1.8

1.7

1.7

1.8

1.6

1.8

1.7

2.0

2.0

1.8

1.9

1.9

1.7

1.9

1.8

1.7

1.8

1.8

1.8

1.9

1.7

1.6

1.8

1.7

1.8

1.6

1.6

1.6

1.6

2.2

2.4

2.2

2.3

2.2

2.4

2.5

2.4

2.5

2.4

2.3

2.5

2.4

2.6

2.4

2.5

2.7

2.8

2.5

2.8

2.9

2.8

2.22

2.3

2.6

2.33

2.29

2.04

0.002

0.003

0.004

0.004

0.008

0.01

0.017

0.031

0.04

0.075

0.093

0.126

0.203

0.339

0.491

0.547

0.83

1.39

1.65

7.23

7.55

6.37

4.79

5.58

12.86

12.48

11.73

13.05

52

52

56

56

59

59

61

64

64

68

68

68

70

73

73

73

75

76

76

82

82

82

82

90

90

90

90

91

15

17

21

24

28

33

45

51

61

89

107

120

158

228

258

282

367

468

515

752

870

976

1096

1556

1704

1989

1876

2049

80M1

80M2

90S

90L

100L1

100L2

112M1

132S2

132M1

160M1

160M2

160L

180L

200L

225S

225M

250M

280S

280M1

315S

315M

315L1

315L2

355M1

355M2

355L2

355L1

355L

100 75 50

Efficiency %


380V 400V 415V

Current

(A) (A) (A)

Locked

rotor

I /IL N

Moment

of inertia

(kg m )

J=1/4 GD

x

2

2

Nosie

level

at1meter

dB(A)

Net

weight

(kg)

Locked

rotor

T /TL N

Pull

up

T /TU N

Break

down

T /TB N

Torque

Full

load

T

(Nm)N

Output

(kW)

Full

lock

speed

(rpm)

100 75 50

power factor, cos

at % full load

φFrame

Size

Performance data

Frame size from 80 to 132




Dimensions foot mount B3

13

GD

G

F

D

DH

GD

GF

D

DH

GD

G

F

D

DH

GD

G

F

D

DH

AC

BB

BCE

ED

LG 2xKK

L

AC

BB

BCE

ED

LG2xKK

L

H

HA

AB

A KAA

HD

AG

AC

BB

BCE

ED

LG 2xKK

L

AC

BB

BCE

ED

LG2xKK

L

HD

H

HA

AB

A

AG

K AA

H

HA

AB

AK AA

HD

AG

HD

H

HA

AB

A

KAA

AG

14

Dimensions foot mount B3

‘*’ Means that the cable gland is only one.

125

140

140

160

190

216

216

254

254

279

279

318

356

356

356

406

406

457

457

457

457

508

508

508

508

508

508

610

610

610

610

610

610

34

36

36

40

45

52

52

67

67

74

74

75

80

80

80

88

88

90

90

90

90

120

120

120

120

120

120

125

125

125

125

125

125

160

180

180

200

230

265

265

320

320

350

350

395

436

436

436

495

495

550

550

550

550

635

635

635

635

635

635

735

735

735

735

735

735

175

190

190

215

236

275

275

330

330

380

380

420

465

465

465

520

520

570

570

570

570

650

650

650

650

650

650

735

735

735

735

735

735

51

60

60

60

75

75

75

95

95

95

95

120

120

120

120

160

160

160

160

160

160

195

195

195

195

195

195

330

330

330

330

330

330

100

100

125

140

140

140

178

210

254

241

279

286

305

311

311

349

349

368

368

419

419

406

457

508

406

457

508

560

630

560

560

630

630

130

135

160

182

195

205

245

260

305

297

335

370

355

380

380

515

440

440

494

494

535

535

515

625

625

625

625

675

775

775

775

775

775

50

56

56

63

70

89

89

108

108

121

121

133

149

149

149

168

168

190

190

190

190

216

216

216

216

216

216

254

254

254

254

254

254

100

19

24

24

28

28

38

38

42

42

48

48

55

60

55

60

60

65

65

75

65

75

65

75

65

80

80

80

75

75

95

95

100

*M6X16

*M8X19

*M8X19

*M10X22

M10X22

M12X28

M12X28

M16X36

M16X36

M16X36

M16X36

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M24X50

M24X50

M24X50

M24X50

M24X50

M24X50

40

50

50

60

60

80

80

110

110

110

110

110

140

110

140

140

140

140

140

140

140

140

140

140

170

170

170

140

140

170

170

210

210

22

32

32

40

40

56

56

80

80

80

80

90

100

80

100

100

100

100

100

100

100

100

100

100

130

130

130

140

110

110

160

140

160

6

8

8

8

8

10

10

12

12

14

14

16

18

16

18

18

18

18

18

18

18

18

20

20

22

22

22

20

20

25

28

25

28

67.5

67.5

15.5

20

20

24

24

33

33

37

37

42.5

42.5

49

53

49

53

53

58

58

67.5

58

67.5

58

58

58

71

71

71

86

86

90

90

6

7

7

7

7

8

8

8

8

9

9

10

11

10

11

11

11

11

12

11

12

11

11

11

14

14

14

12

12

14

16

14

16

80

90

90

100

112

132

132

160

160

180

180

200

225

225

225

250

250

280

280

280

280

315

315

315

315

315

315

355

355

355

355

355

355

10

12.5

12.5

14

14

16

16

19

19

22

22

25

28

28

28

33

33

35

35

35

35

45

45

45

45

45

45

49

49

49

49

49

49

230

260

260

275

310

350

350

425

425

460

460

515

560

560

560

620

620

685

685

685

685

820

820

820

820

820

820

1000

1000

1000

1000

1000

1000

10

10

10

12

12

12

12

14.5

14.5

14.5

14.5

18.5

18.5

18.5

18.5

24

24

24

24

24

24

28

28

28

28

28

28

28

28

28

28

28

28

M24X1.5

M24X1.5

M24X1.5

M24X1.5

M64X25

M30X2

M30X2

M30X2

M36X2

M36X2

M36X2

M36X2

M48X2

M48X2

M48X2

M48X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

295

320

345

385

410

480

520

610

655

680

720

760

825

820

850

925

925

960

975

1000

1015

1160

1270

1270

1190

1300

1300

1500

1500

1530

1570

1530

1570

168.5

140

156

193

200

239

258

270

270

270

277

298

338

338

338

360

360

344

344

344

344

417

417

417

417

417

417

420

420

450

490

450

490

Framesize

A AA AB AC AG B BB C D DH E ED F G GD H HA HD K KK LGLAD

150

140

150

160

185

205

205

250

250

270

270

325

335

335

335

370

370

395

395

395

395

495

495

495

495

495

495

640

640

640

640

640

640

1) 2 Pole motors only.

2) These motor can also be supplied. Please state the

dimensions of the shaft extension on order.

80

90S

90L

100L

112M

132S

132M

160M

160L

180M

180L

200L

225S

225M

225M

250M

250M

280S

280S

280M

280M

315S

315M

315L

315S

315M

315L

355M

355L

355M

355M

355L

355L

1)

1)

1)

1)

1)

1)

1)

1)

1)

2)

2)

The “R” dimension is zero.

15

Dimensions foot-flange mount B35





2xKK

AC

NP

BB

BCE

R

ED

LA

LG

L

AC

NP

BB

BCER

T

LA

LG

ED

2xKK

L

NP

C

E

R

AC

BB

B

ED

LGLA

T

2xKK

L

NP AC

BB

BCR

E

LG

ED

LA

T

2xKK

L

GD

G

F

D

DH

GD

G

F

D

DH

GD

G

F

D

DH

GD

G

F

D

DH

45

o

AG

SM

HD

H

HA

AA

AB

A

K

HD

H

HA

AB

A

M

S

22.5

o

AA K

AG

16

Dimensions foot-flange mount B35

80

90S

90L

100L

112M

132S

132M

160M

160L

180M

180L

200L

225S

225M

225M

250M

250M

280S

280S

280M

280M

315S

315M

315L

315S

315M

315L

355M

355L

355M

355M

355L

355L

125

140

140

160

190

216

216

254

254

279

279

318

356

356

356

406

406

457

457

457

457

508

508

508

508

508

508

610

610

610

610

610

610

A

34

36

36

40

45

52

52

67

67

74

74

80

80

80

80

88

88

90

90

90

90

120

120

120

120

120

120

125

125

125

125

125

125

160

180

180

200

230

265

265

320

320

350

350

395

436

436

436

495

495

550

550

550

550

635

635

635

635

635

635

735

735

735

735

735

735

ABAA

175

190

190

215

236

275

275

330

330

380

380

420

465

465

465

520

520

570

570

570

570

650

650

650

650

650

650

735

735

735

735

735

735

AC

140

150

150

160

185

205

205

250

250

270

270

325

335

335

335

370

370

395

395

395

395

495

495

495

495

495

495

640

640

640

640

640

640

AD

100

100

125

140

140

140

178

210

254

241

279

286

305

311

311

349

349

368

368

630

419

419

406

457

508

406

457

508

560

560

560

630

560

B

130

135

160

182

195

205

245

260

297

305

335

370

355

380

380

440

440

494

494

535

535

515

625

625

515

625

625

675

775

775

775

775

775

BB

50

56

56

63

70

89

89

108

108

121

121

133

149

149

149

168

168

190

190

190

190

216

216

216

216

216

216

254

254

254

254

254

254

C

19

24

24

28

28

38

38

42

42

48

48

55

55

75

75

80

80

60

60

60

65

65

65

65

65

65

65

75

75

95

95

100

100

D

*M6X16

*M8X19

*M8X19

*M10X22

M10X22

M12X28

M12X28

M16X36

M16X36

M16X36

M16X36

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X50

M20X50

M24X50

M24X50

M24X50

M24X50

DH

40

50

50

60

60

80

80

110

110

110

110

110

140

110

140

140

140

140

140

140

140

140

140

140

170

170

170

140

140

170

170

210

210

E

22

32

32

40

40

56

56

80

90

80

80

90

100

80

100

100

100

100

100

100

100

100

100

100

130

130

130

110

110

140

160

140

160

ED

6

8

8

8

8

10

10

12

12

14

14

16

18

16

18

18

18

18

20

20

18

18

18

18

22

22

22

20

20

25

28

25

28

F

15.5

86

42.5

42.5

20

20

24

24

33

33

37

37

49

49

67.5

53

53

53

58

58

58

58

58

58

71

71

71

67.5

67.5

67.5

86

90

90

G

6

7

7

7

7

8

8

8

8

9

9

10

11

10

11

11

11

11

12

11

12

11

11

11

14

14

14

12

12

14

16

14

16

GD

80

90

90

100

112

132

132

160

160

180

180

200

225

225

225

250

250

280

280

280

280

315

315

315

315

315

315

355

355

355

355

355

355

H

10

12.5

12.5

14

14

16

16

19

19

22

22

25

28

28

28

33

33

35

35

35

35

45

45

45

45

45

45

49

49

49

49

49

49

HA

230

260

260

275

310

350

350

425

425

460

460

515

560

560

560

620

620

685

685

685

685

820

820

820

820

820

820

1000

1000

1000

1000

1000

1000

HD

18.5

18.5

14.5

14.5

14.5

14.5

18.5

18.5

10

10

10

12

12

12

12

24

24

24

24

24

24

28

28

28

28

28

28

28

28

28

28

28

28

K

M24X1.5

M24X1.5

M24X1.5

M24X1.5

M30X2

M30X2

M30X2

M36X2

M36X2

M36X2

M36X25

M48X2

M48X2

M48X2

M48X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64x2

M64X2

M64X2

M64X2

M64X2

KK

140

156

168.5

193

200

239

258

270

270

277

277

298

338

338

338

360

360

344

344

344

344

417

417

417

417

417

417

420

420

450

490

450

490

LG

295

320

345

385

410

480

520

610

655

680

720

760

825

850

850

925

925

960

975

1000

1015

1160

1270

1270

1190

1300

1300

1500

1500

1530

1570

1530

1570

L

12

12

12

14

14

14

14

15

15

15

15

17

19

19

19

20

20

22

22

22

22

24

24

24

24

24

24

25

25

25

25

25

25

LA

165

165

165

215

215

265

265

300

300

300

300

350

400

400

400

500

500

500

500

500

500

600

650

600

600

600

600

740

740

740

740

740

740

M

130

130

130

180

180

230

230

250

250

250

250

300

350

350

350

450

450

450

450

450

450

550

550

450

550

550

550

680

680

680

680

680

680

N

200

200

200

250

250

300

300

350

350

350

350

400

450

450

450

550

550

550

550

550

550

660

660

550

660

660

660

800

800

800

800

800

800

P

12

12

12

14.5

14.5

14.5

14.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

24

24

24

24

24

24

24

24

24

24

24

24

S

3.5

3.5

3.5

4

4

4

4

5

5

5

5

5

5

5

5

5

5

5

5

5

5

5

5

5

6

6

6

6

6

6

6

6

6

TAG

51

60

60

60

75

75

75

95

95

95

95

120

120

120

120

160

160

160

160

160

160

195

195

195

195

195

195

330

330

330

330

330

330

‘*’ Means that the cable gland is only one.1) 2 Pole motors only.




1)

1)

1)

1)

1)

1)

1)

1)

1)

2)

2)

Framesize

17





AC

P N

R

E

LG

ED

LA

T

2xKK

L

P N

E

R

LG

ED

LAT

L

LM

AC

2xKK

AG

S

M

P N

ER

LG

LA

T

L

LM

AC

ED

2xKK

ADM

S

AG

AC

2xKK

L

LM

P N

LG

LA

T

E

AG

M

AD

S

GD

G

F

D

DH

GD

G

F

D

DH

GD

G

F

D

DH

GD

G

F

D

DH

Dimensions flange mount B5 and V1

18

Dimensions flange mount B5 and V1

Framesize

LA

355M(V1)

355L(V1)

355M(V1)

355M(V1)

355L(V1)

355L(V1)

AC

175

190

190

215

236

275

275

330

330

380

380

420

465

465

465

520

520

570

570

570

570

650

650

650

650

650

650

735

735

735

735

735

735

AD

140

150

150

160

185

205

205

250

250

270

270

325

335

335

335

370

370

400

400

400

400

495

495

495

495

495

495

645

645

645

645

645

645

AG

51

60

60

60

75

75

75

95

95

95

95

120

120

120

120

160

160

160

160

160

160

195

195

195

195

195

195

330

330

330

330

330

330

D

19

24

24

28

28

38

38

42

42

48

48

55

60

60

60

55

65

65

75

65

75

65

65

65

80

80

80

75

75

95

100

95

100

DH

M6X16

M8X19

M8X19

M10X22

M10X22

M12X28

M12X28

M16X36

M16X36

M16X36

M16X36

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M20X42

M24X50

M24X50

M24X50

M24X50

M24X50

M24X50

E

40

50

50

60

60

80

80

110

110

110

110

110

140

110

140

140

140

140

140

140

140

140

140

140

170

170

170

140

140

170

170

210

210

ED

22

32

32

40

40

56

56

80

80

80

80

90

80

100

100

100

100

100

100

100

100

100

100

100

130

130

130

110

110

140

160

140

160

F

6

8

8

8

8

10

10

12

12

14

14

16

18

16

18

18

18

18

18

18

18

18

20

20

22

22

22

20

20

25

28

25

28

G

15.5

86

42.5

42.5

20

20

24

24

33

33

37

37

49

49

58

53

53

53

58

58

58

58

58

71

71

71

67.5

67.5

67.5

67.5

86

90

90

GD

6

7

7

7

7

8

8

8

8

9

9

10

11

10

11

11

11

11

12

11

12

11

11

11

14

14

14

12

12

14

16

14

16

KK

*M24X1.5

*M24X1.5

*M24X1.5

*M24X1.5

M30X2

M30X2

M30X2

M36X2

M36X2

M36X2

M36X2

M48X2

M48X2

M48X2

M48X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

M64X2

L

295

320

345

385

410

480

520

610

655

685

720

760

825

820

850

925

925

960

975

1000

1015

1160

1270

1270

1190

1300

1300

1500

1500

1530

1570

1530

1570

LG

140

156

168.5

193

200

239

258

270

270

277

277

298

338

338

338

360

360

344

344

344

344

417

417

417

417

417

417

420

420

450

490

450

490

LM

1630

-

-

-

-

-

-

-

665

720

755

795

845

894

889

919

1051

1051

1090

1090

1090

1090

1258

1368

1368

1288

1398

1398

1600

1600

1630

1670

1670

12

12

12

14

14

14

14

15

15

15

15

17

19

19

19

20

20

22

22

22

22

24

24

24

24

24

24

25

25

25

25

25

25

M

165

165

165

215

215

265

265

300

300

300

300

350

400

400

400

500

500

500

500

500

500

600

600

600

600

600

600

740

740

740

740

740

740

N

130

130

130

180

180

230

230

250

250

250

250

300

350

350

350

450

450

450

450

450

450

550

550

550

550

550

550

680

680

680

680

680

680

P

200

200

200

250

250

300

300

350

350

350

350

400

450

450

450

550

550

550

550

550

550

660

660

660

660

660

660

800

800

800

800

800

800

S

12

12

12

14.5

14.5

14.5

14.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

18.5

24

24

24

24

24

24

24

24

24

24

24

24

T

3.5

3.5

3.5

4

4

4

4

5

5

5

5

5

5

5

5

5

5

5

5

5

5

6

6

6

6

6

6

6

6

6

6

6

6

‘*’ Means that the cable gland is only one.1) 2 Pole motors only.




1)

1)

1)

1)

1)

1)

80

90S

90L

100L

112M

132S

132M

160M

160L

180M

180L

200L

225S

225M

225M

250M

250M

280S

280S

280M

280M

315S

315M

315L

315S

315M

315L

1)

1)

1)

2)

2)

Dimensions face-flange mount B14A and B14B

Frame size from 80 to 160 B14A

Frame size from 80 to 112 B14B

19

AC

L

P N

R

E

LG

ED

T

2xKK

GD

G

F

D

DH

P N

R

T

AC

E

ED

LG

L

2xKKG

DG

F

D

DH

Frame

sizeM N P S T M N P S T

80 100 80 120 M6 3 130 110 160 M8 3.5

90S 115 95 140 M8 3 130 110 160 M8 3.5

90L 115 95 140 M8 3 130 110 160 M8 3.5

100L 130 110 160 M8 3.5 165 130 200 M10 3.5

112M

AC

175

190

190

215

236

AD

150

165

165

170

195

AG

51

60

60

60

75

D

19

24

24

28

28

DH

M6X16

M8X19

M8X19

M10X22

M10X22

E

40

50

50

60

60

ED

22

32

32

40

40

F

6

8

8

8

8

G

15.5

20

20

24

24

GD

6

7

7

7

7

KK

*M24X1.5

*M24X1.5

*M24X1.5

*M24X1.5

M30X2

L

295

320

345

385

410

LG

140

156

168.5

193

200 130 110 160 M8 3.5 165 130 200 M10 3.5

B14A B14B

160M 330 265 95 42 M16X36 110 80 12 37 8 M36X2 610 270 215 180 250 M12 4 265 230 300 M12 4

132M 275 215 75 38 M12X28 80 56 10 33 8 M30X2 520 258 165 130 200 M10 3.5 215 180 250 M12

132S 275 215 75 38 M12X28 80 56 10 33 8 M30X2 480 239 165 130 200 M10 3.5 215 180 250 M12 4

160L 330 265 95 42 M16X36 110 80 12 37 8 M36X2 655 270 215 180 250 M12 4 265 230 300 M12 4

4

‘*’ Means that the cable gland is only one.


Frame size from 160 to 31531 4

C

6 7 8

B

A

C

4321

B

A

5 7 86

B

5 6 87Frame size 355

A

C

1 2 3 4

Terminal box

20

Frame

sizeA B C 1 2 3 4 5 6 7 8

80~90 104 104 48 M6X16 M4 M6X25 M6X12 M6X12 M5X16 2XM25X1.5 2XPG16

100~132 118 181 62 M6X16 M5 M6X25 M6X12 M6X12 M5X16 2XM32X1.5 2XPG21

160~180 200 164 83 M6X20 M3 M8 M8X30 M4X25 M8X16 M8X16 M5X16 2XM40X1.5 2XPG29



315 441 326 195 M8X30 M3 M12 M10X50 M4X25 M10X16 M10X20 M8X30 2XM63X1.5 2XPG48

315 490 365 220 M8X30 M3 M16 M10X25 M4X25 M10X25 M10X25 M8X30 2XM63X1.5 2XPG48

Metric Gland

Sizes

PG Gland

Sizes

21

Bearing and oil seal

Bearing data

D d

B

DE NDE d D B

80 6204 ZZ C3 6204 ZZ C3 20 47 14

90 6205 ZZ C3 6205 ZZ C3 25 52 15

100 6206 ZZ C3 6206 ZZ C3 30 62 16

112 6306 ZZ C3 6306 ZZ C3 30 72 19

132 6308 ZZ C3 6308 ZZ C3 40 90 23

160 6309 C3 6309 C3 45 100 25

180 6311 C3 6311 C3 55 120 29

200 6312 C3 6312 C3 60 130 31

225 6313 C3 6313 C3 65 140 33

250 6314 C3 6314 C3 70 150 35

280 2P 6314 C3 6314 C3 70 150 35

280 4-8P 6316 C3 6316 C3 80 170 39

(Horizontal)315 2P 6316 C3 6316 C3 80 170 39

315 4-8P (Horizontal) NU319 C3 6319 C3 95 200 45

315 4-8P (Vertical) NU319 C3 7319 95 200 45

355 4-8P (Horizontal) NU322 C3 6322 C3 110 240 50

355 4-8P (Vertical) NU322 C3 7322 110 240 50

315 2P (Vertical) 6316 C3 7316 80 170 39

355 2P (Horizontal) 6319 C3 6319 C3 95 200 45

355 2P (Vertical) 6319 C3 7319 95 200 45

Oil seal data

B

d D

Frame sizeFrame size DE NDE

d D DdB B

80 20 35 5 20 35 5

90 25 40 5 25 40 5

100 30 52 7 30 52 7

112 30 52 7 30 52 7

132 40 62 5 40 62 5

160 45 65 8 45 65 8

180 55 75 8 55 75 8

200 60 80 8 60 80 8

225 65 90 10 65 90 10

250 70 95 10 70 95 10

280 2P 70 95 10 70 95 10

280 4-8P 80 100 10 80 100 10

315-2P 80 100 10 80 100 10

315 4-8P 95 120 12 95 120 12

355 2P 95 120 12 95 120 12

355 4-8P 110 140 12 110 140 12

22

Notes:* 2 Pole motors only.1. Vertical motors should be greased twice as often as horizontal motors.2. Regreasing time should be reduced if bearing operating temperature is in excess of 70 C.

0

Enertech Electric Motors (Australia) reserves right to make changes to this brochure without notice.

Bearing lubrication

Frame

size

Drive

end bearing

Non–drive

end bearing

Regreasing period hours for

operating temperatures up to 70°C

Quantity of

grease in

bearing chamber

rpm<3600 rpm<1800 rpm<1200 grams

160 6309 C3 6309 C3 6000 12000 18000 13

180 6311 C3 6311 C3 4000 11000 16000 15

200 6312 C3 6312 C3 3500 8500 13000 20

225 6313 C3 6313 C3 3000 6000 9000 22

250 6314 C3 6314 C3 2000 5000 8000 23

280* 6314 C3 6314 C3 1200 – – 30

315* 6316 C3 6316 C3 1200 – – 30

355* 6319 C3 6319 C3 1200 – – 30

280 6316 C3 6316 C3 – 4000 6000 30

315 NU319 C3 6319 C3 – 2000 3000 45

355 NU322 C3 6322 C3 – 1400 2200 60

1

4

5

6

7

8

2

3

1011

12

1314

15

16

17

18

9

Motors of frame sizes 160–355 are fitted with open bearings and regreasing device. Depending on the useful

life of grease, open bearings must be regreased in good time so that the scheduled bearing service life is

reached.

ESC motors are equipped with bearings from excellent manufacturers.

In general the bearings have C3 clearances.

Motors of frame sizes 80–132 are fitted with life–lubricated bearings.

1. Endshield D.E2. Flange3. Oil seal4. Terminal Box Lid5. Seal Gasket

6. Terminal Box Base7. Terminal Board8. Terminal Gasket9. Stator10. Key

11. Bearing D.E12. Rotor13. Inner Bearing Cap14. Bearing N.D.E

15. Endshield N.D.E16. Fan17. Snap Ring18. Fan Cowl

Enertech Electric Motors Products are sold and recommended by :

HEAD OFFICE

Address:

Tel:

Fax:

5 Kintyre Court, Greenvale 3059, Victoria, Australia.

+ 61 (0)3 9333 6605

+ 61 (0)3 9333 6603

Trung Kien

Text Box

Trung Kien

Typewriter

122, Do Xuan Hop, Phuoc Long A Ward, District 9, Ho Chi Minh City. Phone: +84.8 3728 2738 Fax: +84.8 3728 2740 www.cuulongmachinery.com

Trung Kien

Stamp

ESC Three Phase IEC Low Voltage - maybomchinhhang.vn

Documents

Transcript of ESC Three Phase IEC Low Voltage - maybomchinhhang.vn