EInstruction AdjustItPro G2 Installation Guide

8/12/2019 EInstruction AdjustItPro G2 Installation Guide

1/18

Assembly instruction for

standfor Dual Board 1279, 1289 and 1297


2/18


3/18

3Assembly instruction for AdjustIt Pro stand

Overview

The AdjustIt Pro height adjustable mount and stand for eInstruction Dual Boards accom-modates the needs of both teacher and student. Now everyone can raise or lower the white-board to a comfortable level. The spring mechanism provides smooth operation with 20inches of height-adjustability.

The AdjustIt Pro is a modular conguration for mounting the 1279, 1289 or 1297 DualBoard with a projector arm to accommodate short throw or ultra short throw projectors.

Important considerations

1. Measure the height of any door that the system is expected to pass through.This information is required for initial setup.

2. The total system weighs between 154 - 200 lb (70 kg - 91 kg) and should be installed withcare. Two people are required for some steps of the installation.

3. The installer must verify compliance with all local building codes and ensure that thesupporting wall surface will safely support the combined load of all equipment plus aconservative safety factor and that correct mounting hardware is being used.

4. Please use the system only as intended. Do not hang from or climb on the system.

5. No unauthorized modications or additions are to be made to the system.

CAUTION The springs in the height adjustable unit can store a large amount of energy; use carewhen assembling, installing and adjusting.DO NOT remove the locking pin to raise the assembly without rst installing the boardand projector.Follow all installation instructions when setting tension and adjusting height ofassembly.Failure to place system in equilibrium prior to pin removal could result in seriouspersonal injury.


4/18


5/18


Before installation SKU explanation

The AdjustIt Pro mount & stand is a modular system, providing a height adjustable solutionfor merely every application.

The system consists of the following components:

description:

spring tension mechanism

G2 board framewith integrated support for G2` postRecommended for mobile applications.

G2 height adjustable post withswivel head, to accommodateG2-AP-.. projector mounts

`G2 long projector arm with universalmount to accommodate short throwprojectors with max. 4 ft. throw distance

G2 projector head / mounting plate foruse with Ultra Short Throw projectors

part number:

IW-A-118-075-001-R

IW-A-118-075-003-R

IW-A-118-075-004-R

IW-A-118-075-006-R

IW-A-118-075-0xx-R

Picture:


6/18


Before installation SKU explanation

description:

`G3` board framewith integrated FIXED projector arm supportto accommodate third party wall mount armsor to accommodate G3-AP-G1G projector arm

`G3` long projector arm with universal mountto accommodate short throw projectors withmax. 4 ft. throw distance

Mobile stand

Notebook shelf (optional)

part number:

IW-A-118-075-002-R

IW-A-118-075-013-R

IW-A-118-075-005-R

IW-A-118-075-014-R

Picture:


7/18


Before installation hardware / required tools

Mounting hardware included:

NHV-G2:

Required tools:

To assemble board frame to spring mech:4x Allen head screw M8 x 20 6mm Allen wrench8x 8 mm washer4x selocking nut M8

To assemble board to board frame:4x hexagon head screw 10/32 x 3/4 8mm hexagon headwrench

The NHV-G3 comes with before mentionedNHV-G2 hardware and also includes:

To assemble G3 plate to board frame:

To assemble the stand:8x Allen head screw M10 x 60 8 mm Allen wrench8x 10 mm washer

To assemble the handles to the stand:4x Button head screw M8 x 55 5mm Allen wrench

To assemble the spring mech. to the stand:4x Allen head screw M8 x 85 6mm Allen wrench4x 8mm washer large (on back side of the stand)4x 8mm washer small (on front side of the stand)4x self locking screw nut M6

Mounting hardware included:

MST-US:

Required tools:


8/18


Assembly of the mobile stand

To assemble the stand:

1. Unpack the 2 legs, 2 feet and center bar.Sort the left hand and right hand legs andfeet, see picture below

2. Attach the feet to the legs, using the 2 pcs.M10x60 screws and 2 pcs. M10 washersper foot/leg. Ensure that the casters withbrakes are in front.

3. Attach the center bar between the 2 legs,using 2 pcs. M10x60 screws and 2x M10

washers on each side.4. Attach the handles to the stand using the

button head screws M8x55.

5. Tighten all screws rmly.

6. Put the stand in its upright position andlock the casters.

LR

L

R


9/18


Add the notebook shelf (optional)

To install the notebook shelf:

1. Put the shelf on the frame with the raisedlip towards the rear of the stand

2. Position the screws and push them throughnotebook shelf and stand base.Use a rubber hammer to gently drive thescrews into the shelf

3. Install one washer and one wing nut oneach side and secure the shelf


10/18

Assembly instruction for AdjustIt Pro stand

Assembly of height adjustable mount NHV-G2

1. Unpack spring mechanism and G2 frame

2. Attach board frame to the spring mechanism using 4x M8 Allen head screws, washers

and bolts

Assembly of height adjustable mount NHV-G3

1. Unpack spring mechanism and G3 frame

2. Attach board frame to the spring mech.using 4x M8 Allen head screws, washers

and bolts

10


11/18


Attaching the mount to the wall

1. Mark the position of the 4 holes on the wall:- lower holes at appr. 51 from the oor- lateral distance between the holes: 55.1- vertical distance between holes: 19.1

2. Drill the holes, using a 12mm drill

3. Fix the mount to the wall, using the correcthardware

Mounting hardware for wall mounting is NOT included. Its the responsibility of the installer to verify compliance with all local building codes and

to ensure that the supporting wall surface will safely support the combined load of allequipment and that the proper mounting hardware is being used.

1.400 mm

1.400 mm

2 7 7 m m

2 7 7 m m

1 . 3

0 0 m m

Floor


12/18


Attaching the mount to the mobile stand

1. Choose the mounting height:The mobile stand allows for the mountto be at tached in 3 different heights.Low position: use the lowest position(3rd and 6th hole) if clearance of lowestdoor is less than 77.5 / 195cm or forapplications in Kindergarten or Primaryeducation where lower board heightsare required.High position: if clearance is greater than77.5 / 195cm and for applicationswhere higher board heights are prefered.

2. Put the M8x80 screws in the desired upperholes from the back side of the frame.Useone washer under each bolt head.

3. Tape the screws to the frame. This willmake it easier to attach the mount to thestand.

4. Place the mount onto the stand andsecure the mount with one M8 washer

and M8 nut per screw .


13/18


Securing the spring tension

Securing the spring tension mechanism to the lowest position

CAUTION The springs in the height adjustable unit can store a large amount of energy;use care when assembling, installing and adjusting.DO NOT remove the locking pin to raise the assembly without rst installing the boardand projectorFollow all installation instructions when setting tension and adjusting height of assembly.Failure to place system in equilibrium prior to pin removal could result in serious personalinjury.

The spring tension mechanism should be secured in its lowest position before proceeding withthe installation of board and projector.Two people are required to perform this step.

To secure the spring tension mechanism to the lowest position:

1. pull the mechanism down. Use caution;the spring mechanism stores a largeamountof energy. If suddenly released,the moving carriage could inict personalinjury.

2. Have a second person secure the system inits lowest position by inserting the retentionpin. The retention pin ts in the through-and-through hole of the vertical tube.After inserting pin, roll clip around thevertical tube to secure.


14/18


Installing the G2 projector post (applies only for mounts with G2 board frame)

To install the G2 post:

1. Remove the M10 bolts, which will be usedafter assembly to secure the arm in theprojection position.

2. Slide the projector post into the projectorarm support

3. Select one of the 7 available mountingpositions, considering the available roomheight and door clearance, and secure thepost with the M10 hexagon head screws.

Post

Projector arm support


15/18


Attaching the Dual Board to the frame

The Dual Board is attached to the mount using the mounting rail on the back side of theboard.To attach the Dual Board to the height adjustable mount:

1. Insert 2 #10-32 x 3/4 screws into the inserts in the upper mounting rail on theback side of the board.

2. Hang the board into the frame

3. Before inserting the 2 #10-32 x 3/4 screws into the lower mounting rail,position the aluminium pen tray between the Dual Board and the board frame.

4. Secure all 4 screws tightly


16/18


Installing the projector mount to NHV-G2 projector post

1. Mount the projector to the projector mount(see assembly instruction projector mount)

2. Temporarily loosen the knurled head screwand remove the 2 Allen head screwson the projector post

3. Slide the mount underneath theknurled head screw and washerand secure it.

4. Secure the mount by reinstalling andtightening the Allen head screws

5. Use the crank at the projector arm toadjust the height of the projector.

6. Use the two socket head jack screwsto adjust the side-to-side tilt of the projector.Tightening the right screw raises the rightside of the projector and tightening the leftscrew raises the left side of the projector.

7. If, in case of a mobile application, theprojector needs to be pushed sideways toallow for the stand to t through a dooropening, loosen the knurled head screwat the bottom of the mount and push themount and projector parallel to the board.

8. At the place of presentation reposition themount and projector in its initial positionand secure the knurled head screw.


17/18


Adjusting the spring tension

During installation, the spring-tension mechanism is secured in its lowest position.

After installation is complete and both board and projector have been mounted

the mount has to be balanced to the total weight of the conguration.

To balance the system the spring tension needs to be adjusted.

CAUTION The springs in the height adjustable unit can store a large amount of energy;use care when assembling, installing and adjusting.DO NOT remove the locking pin to raise the assembly without rst installing the board

and projector

Before adjusting the spring tension:

1. apply downward force to the board2. release the locking pin3. release the board slowly

If the board comes down, spring tension has to be increased,if the board starts moving up, spring tension has to be decreased.

This is accomplished by using a 17 mm ratchet to turn the screw located on the right handside of the spring-ension mechanism. Turn clockwise to increase the tension,turn counter-clockwise to decrease the tension.

Adjust tension such that the board stays in the same position when moved up/down andreleased and such that the system moves up and down with little operator effort.


18/18

EInstruction AdjustItPro G2 Installation Guide

Documents

Transcript of EInstruction AdjustItPro G2 Installation Guide