Echlin Digital Fuel Injector Belden Flow Bench and ...
Transcript of Echlin Digital Fuel Injector Belden Flow Bench and ...
BeldenEchlin Digital Fuel Injector Flow Bench and Ultrasonic
Cleaning System
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
IMPORTANT - INJECTOR SERVICE INFORMATION
QUALIFY THE INJECTORS TO BE SERVICED BY PART NUMBER AND APPLICATION.
CORROSION OR RUST CONTAMINATION IN INJECTOR INLET CANNOT BE PROPERLY
CLEANED. CLEANING INJECTOR WILL NOT RESOLVE PROBLEM AND INJECTORS MUST BE
REPLACED.
INJECTORS WITH BROKEN OR DAMAGED PINTLE TIPS CANNOT BE REPAIRED.
INJECTORS MUST BE REPLACED.
BEFORE DISASSEMBLING THE INJECTOR, MAKE SURE YOU HAVE THE NECESSARY REPAIR
COMPONENTS. SOME INJECTOR COMPONENTS CANNOT BE REPLACED OR ARE NOT
AVAILABLE FROM ASNU. REFER TO THE INJECTOR INDEX.
ADAPTER APPLICATIONS: WE ARE NOT ABLE TO IDENTIFY EVERY APPLICATION THIS IS
ONLY A GUIDE, PLEASE REPER TO PAGES TO THE INJECTOR INDEX.
ACCESSORY INFORMATION: REFER TO PAGES
FOR THE BEST PERFORMANCE, CLEANED INJECTORS SHOULD BE INSTALLED IN VEHICLE
IMMEDIATELY AFTER SERVICING WITH ASNU.
SHELF LIFE: SERVICED INJECTORS THAT WILL NOT BE RE-INSTALLED TO A VEHICLE
ENGINE MUST BE TREATED WITH AN INHIBITER AND FITTED WITH EITHER 2-15110 OR
2-15114 DUST PROTECTION CAPS. FAILURE TO FOLLOW RECOMENDATIONS COULD
RESULT IN SEIZURE OF INTERNAL COMPONENTS.
REFER TO ASNU OPERATION MANUAL FOR PROPER PROCEDURE.
DUST PROTECTION CAPS MUST BE INSTALLED TO PREVENT CONTAMINATION & PRE-
SURVE INJECTOR SHELF LIFE. SEE INJECTOR INDEX TO SELECT PROPER
PROTECTIVE CAPS.
Page Page Page Page 2222
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Machine Warranty
Page Page Page Page 3333
All repairs or replacements of machines will be handled NAPA Echlin DSM. All questions regarding inoperative machines will be conducted through your local NAPA Echlin DSM.
If a machine breaks down and repairs cannot be determined in the field, the NAPA Echlin DSM will get authorization to ship the machine back to the factory for repairs or replacement for up to one year after purchase. The customer will be instructed where to ship the machine prepaid and then all freight charges will be re-reimbursed.
If the customer is able to determine the problem causing an inoperative machine, upon approval of the NAPA Echlin DSM, the necessary parts will be shipped on a no charge basis for up to one year after purchase. The customer will perform the replacement of these parts. No labor will be paid for customer installed components.
In instances where the machine has been damaged due to user neglect, we will ship parts for a charge, plus freight. If repairs are done at the ASNU repair center, all freight, parts and labor are the responsibility of the user.
After the 12 month warranty period, the user may continue to have the machine serviced at the ASNU Repair Center, on a labor, materials and freight cost basis.
The ASNU Repair Center will not be responsible for any damage which occurs during the shipment of a machine back to the user.
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
BOSCH
Various
Page
ROCHESTER
GM MULTEC
Page
LUCAS
DISC
Page
WEBER
MPI
Page
DENSO
Ford/Mazda/Kia
Page
HONDA
KEIHIN STYLE
Page
BOSCH
Various
Page
DELPHI
Page
Machine Warranty
Section 1 Page Section 1 Page Section 1 Page Section 1 Page 1111
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Injector Index
BOSCH
Page
BOSCH D-JET
Page
BOSCH
Trumpet Cap Type
Page
BOSCH
Ford/Mazda
Page
BOSCH D-JET
Page
BOSCH K-JET
Various Types
Page
BOSCH
Toyota/Mitsubushi
Page
DENSO
Chrysler/Mitsubishi
Page
JECS
Nissan
Page
BOSCH
Chrysler
Page
BOSCH
Ford CFI
Page
SIEMENS GDI
Citroen/Peugeot
Page
Page Page Page Page 2222
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Injector Index
HITACHI GDI
Mitsubushi
Page
BOSCH GDI
VW
Page
BOSCH GDI
Ford
Page
BOSCH
Ford
Page
WEBER
Fiat/PSA
Page
SIEMENS
VW/Audi
Page
SIEMENS
VW/Audi
Page
BOSCH
Ford
Page
SIEMENS
Chysler
Page
SAGEM AIR ASSISTED
BMW/KIIA
Page 40
Page Page Page Page 3333
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Injector Index
ROCHESTER/WEBER
Page
ROCHESTER/WEBER
Page
BOSCH / HOLLY
Page
DENSO
Nissan /Subaru
Page
BOSCH
Chrysler
Page
BOSCH/WEBER
DENSO/SIEMENS
Page
JECS
Nissan/Toyota
Page
JECS
Nissan
Page
JECS
Toyota
Page
JECS
Nissan
Page
DENSO
Mazda
Page
DENSO
Nissan
Page
Page Page Page Page 4444
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Injector Index
KEIHIN
Honda
Page
KEIHIN
Honda
Page
BOSCH
Ford
Page
BOSCH
Nissan
Page
BOSCH
Chrysler
Page
DENSO
Susuki
Page
GM EARLY VORTEC SYSTEMS
Page
GM LATE VORTEC SYSTEMS
Page
GM LATE VORTEC SYSTEMS
Page
Page Page Page Page 5555
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
GM / BMW
MERCEDES
(16V & 24V ENGINES)
BOSCH
MULTI HOLE TYPE
2-15536 with filter in.
2-15001
FILTER
2-15004
O-RING-BROWN
TOP & BOTTOM
2-15114
DUST CAP
2-15662
SPACER-1mm
2-15038
PINTLE CAP
MULTIHOLE 3mm
HOLE
2-15012
SPACER 2mm
2-15671
PINTLE CAP
MULTIHOLE
OPEN ENDED
2-15663
PINTLE CAP
FOR BMW
3mm HOLE
2-15035
PINTLE CAP
3mm HOLE
2-15511
Test Adapter for
injectors with
filter removed
2-15536
Test Adapter for
injectors with
filter installed
2-15502
Universal Injector
Wire Harness
Top Feed Injectors
Section 3 Page 1Section 3 Page 1Section 3 Page 1Section 3 Page 1
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
GM
ROCHESTER MULTEC
Use Adapter 2-15536
with filter in.
2-15001
FILTER
2-15004
O-RING-BROWN
TOP & BOTTOM
2-15114
CAP (2 REQ)
2-15109
SPACER
2-15511
Test Adapter for
injectors with
filter removed
2-15536
Test Adapter for
injectors with
filter installed
2-15502
Universal Injector
Wire Harness
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 2222
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Warning
Use only ASNU
02 with these
Injectors
ROVER / BMW
SAAB / PSA
LUCAS IDISC
Use Test Adapter
2-15536 with filter in.
2-15013
O-RING
TOP AND BOTTOM
NA
FILTER
2-15110
CAP (2 REQ)
2-15511
Test Adapter for
injectors with
filter removed
2-15536
Test Adapter for
injectors with
filter installed
2-15502
Universal Injector
Wire Harness
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 3333
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
FORD / FIAT
PSA (EUROPE)
Weber
Use Test Adapter
2-15536 with filter in.
NA
FILTER
NA
PINTLE CAP
2-15012
SPACER
2-15004
O-RING
2-15114
CAP (2 REQ)
2-15511
Test Adapter for
injectors with
filter removed
2-15536
Test Adapter for
injectors with
filter installed
2-15502
Universal Injector
Wire Harness
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 4444
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
FORD / FIAT
PSA (EUROPE)
Weber
Use Test Adapter
2-15536 with filter in.
2-15001
FILTER
2-15019
PINTLE CAP
2-15009
O-RING
2-15007
DUST SEAL
2-15114
DUST CAP
2-15008
HEAD SEAL
2-15110
DUST CAP
2-15511
Test Adapter for
injectors with
filter removed
Test Adapter 2-15538
test injectors with
filter installed
2-15502
Universal Injector
Wire Harness
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 5555
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
HONDA
KEIHIN STYLE
Use Test Adapter
2-15538 with filter in.
2-15014
GREEN SEAL
2-15015
O-RING
2-15041
HEAD SEAL
PINTLE CAP CANNOT BE REPLACED. DO NOT REMOVE
FOR INJECTOR CLEANING OR TESTING
2-15016
GROMMET
2-15064
FILTER
2-15114
CAP
2-15110
CAP
2-15511
Test Adapter for
injectors with
filter removed
2-15538
Test Adapter for
injectors with
filter installed
2-15502
Universal Injector
Wire Harness
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 6666
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
VARIOUS
VEHICLES
BOSCH EV6
MULTIPOINT
Use Test Adapter
2-15538
use Adapter 2-15640
plate in fuel rail for testing
2-15013
O-RING
(TOP & BOTTOM)
2-15001
FILTER
USE 2-15640 - INJECTOR MOUNTING PLATE IN
FUEL RAIL TO HOLD INJECTORS
PLASTIC O'RING RETAINING WASHER NOT YET
AVAILABLE, REMOVE CAREFULLY AND RE-USE OLD WASHER
2-15511
Test Adapter for
injectors with
filter removed
2-15536
Test Adapter for
injectors with
filter installed
2-15502
Universal Injector
Wire Harness
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 7777
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 8888
BUICK Delphi production
Use Injector Adapter 2-15536
Use custom harness 2-15637
2- O-RING (LOWER)
2- O-RING (UPPER)
2-15001 FILTER
USE ASNU 89 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS
PINTLE CAP NOT YET AVAILABLE DO NOT REMOVE
INJECTOR ADAPTER 2-15536
(Tests Injectors with filter installed)
DELPHI WIRING HARNESS 2-15637
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
GM / JAGUAR FIAT-ALFA
Use Adapter 2-15537 with hose and filter
installed
2-15020 PINTLE CAP
2-15019 PINTLE CAP
2-15006 O-RING
2-15001 FILTER
2-15110 CAP
2-15114 CAP
2-15010 O-RING
2-15024 FERRULE
2-15011 SEAL
2-15511 Test Adapter for injectors with filter removed
2-15537 Tests injectors with hose
& filter installed
2-15502 Universal Injector Wire Harness
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 9999
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
MERCEDES JAGUAR / VOLVO
BOSCH D-JETRONIC Use Adapter 2-15537 with hose installed Use Adapter 2-15511
without hose and filter installed
Connect Injectors with 2-15502
Universal Harness
2-15019 PINTLE CAP
2-15001 FILTER
2-15006 O-RING
2-15011 SEAL
2-15110 CAP
2-15114 CAP
2-15006 HEAD SEAL
2-15024 FERRULE
2-15511
(ASNU 51) Test Adapter for injectors with filter removed
2-15537
(ASNU 58) Tests injectors with hose
& filter installed
2-15502
(ASNU 70) Universal Injector Wire Harness
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 10101010
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 11111111
GM / SAAB Chimney Style
Aliminium Pintle Cap 2-15536 with filter in
Replacement cap not available, remove and replace
with 2-15672
2-15012 WASHER
ASNU 14 O-RING (2 REQ)
2-15001 FILTER
2-15017 PLASTIC PINTLE CAP RENAULT CLIO ONLY
ASNU 23 BOTTOM O'RING RENAULT
CLIO ONLY
2-15110 CAP
2-15114 CAP
2-15511 Test Adapter for injectors with filter removed
2-15536 Tests injectors with hose &
filter installed
2-15502 Universal Injector Wire Harness
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 12121212
FORD / HYUNDAI MAZDA / PROTON Pintle type with
SINGLE SPRAY exit hole. For Multi Hole Spray
See page 25
Use Test Adapter 2-15538 with filter in
2-15096 PINTLE CAP BLACK - 10 DEG
2-15097 PINTLE CAP BLACK - 18 DEG
2-15098 PINTLE CAP BLACK - 3 DEG
2-15099 PINTLE CAP
2-15067 PINTLE CAP
2-15070 PINTLE CAP 18 SPRAYS
2-15001 FILTER
2-15110 CAP
2-15114 CAP
2-15007 bushing
2-15009 O'RING
2-15102 O'RING
2-15008 HEAD SEAL
2-15511 Test Adapter for injectors with filter removed
2-15538 Tests injectors with filter in-
stalled
2-15502 Universal Injector Wire Harness
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 13131313
CADILLAC Use Test Adapter 2-15511
Connect Injectors with 2-15502 Universal Harness
2-15019 PINTLE CAP
ASNU 240 COPPER WASHER
2-15001 FILTER
2-15110 CAP
2-15107 BLEEDER O-RING
2-15006 HEAD SEAL
2-15302 O-RING
Test Adapter 2-15511
tests injectors with hose & filter removed
2015502 Universal Injector Wire Harness
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 14141414
K-JETRONIC BOSCH MECHANICAL FUEL INJECTOR &
COLD START VALVES
Use Adapter 2-15535 or 2-15514 or 2-15515
2-15002 O-RING
2-15109 0-RING
AUDI APPLICATIONS
2-15114 CAP
2-15110 CAP
2-15108 MOUNTING SEAL
VARIOUS
2-15101 MOUNTING SEAL
BMW
Test Adapter 2-15535 10mm Female Coupling For Male K-Jet & Cold Start
Test Adapter 2-15514 8mm Male
Coupling for Female K-Jet & Cold Start
Test Adapter 2-15515 12mm Female Coupling
for Male K-Jet
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 15151515
MAZDA Use Test Adapter
2-15538 with filter in
2-15009 O-RING
2-15008 HEAD SEAL
2-15106 BUSHING
2-15019 PINTLE CAP
2-15001 FILTER
2-15110 CAP
2-15114 CAP
Test Adapter 2-15511 test s injectors with filter removed
Test Adapter 2-15538 tests injectors with filter
installed
2-15502 Universal Injector Wire Harness
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 16161616
TOYOTA MAZDA Use test Adapter
2-15538 with filter in
2-15009 O-RING
2-15008 HEAD SEAL
2-15007 DUST SEAL
ASNU 241 O-RING
2-15055 SEALING O-RING
ASNU 243 HOUSING SEAL
2-15062 HOUSING RING
2-15001 FILTER
2-15021 PINTLE CAP
2-15019 PINTLE CAP
2-15110 DUST CAP
2-15114 DUST CAP
Test Adapter 2-15511 tests injectors with filter
removed
Test Adapter 2-15538 tests injectors with
filter installed
2-15502 Universal Injector Wire Harness
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 17171717
CHRYSLER NISSAN
Use Test Adapter 2-15538 with filter in
Connect Injectors w/ 2-15502 Universal Harness
2-15009 O-RING
2-15033 COLLAR
2-15094 INSULATOR SEAL
2-15110 DUST CAP
2-15114 DUST CAP
Test Adapter 2-15511tests injectors with filter removed
Test Adapter 2-15538 tests injectors with filter installed
2-15502 Universal Injector Wire Harness
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 18181818
NISSAN Use Test Adapter 2-15538
with filter in Connect injectors w/ 2-15502
Universal Harness
2-15001 FILTER
2-15019
PINTLE CAP
2-15006 O-RING
2-15009 O-RING
2-15051 BUSHING
2-15110 DUST CAP
2-15114
DUST CAP
2-15511 Test Adapter for injectors with filter removed
2-15538 Test Adapter for injectors with filter installed
2-15502 Universal Injector Wire Harness
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 19191919
CHRYSLER TBI
SINGLE UNIT
Use Test Adapter 2-15536
with filter in
2-15001 FILTER
2-15110 DUST CAP BOTTOM
2-15114 DUST CAP TOP
2-15004 TOP O-RING
2-15011 BODY CLAMPING SEAL
ASNU 273 LOWER BODY O'RING SEAL
2-15536 INJECTOR ADAPTER
Tests injectors with filter installed
2-15502 Universal Injector Wire Harness
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 20202020
FORD CFI DUAL UNIT
Use Test Adapter 2-15511
2-15501 FILTER
2-15312 FILTER CFI
2-15068 PINTLE CAP
2-15069 PINTLE CAP
2-15304 LOWER O-RING
2-15302 UPPER O-RING
2-15114 DUST CAP TOP
2-15110 DUST CAP BOTTOM
2-15511 INJECTOR ADAPTER
Tests injectors with filter removed
2-15502 Universal Injector Wire Harness
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 21212121
CITROEN PEUGEOT- GDI
SIEMENS Gasoline Direct Injection
Use Test Adapter ASNU 56 with filter in
ASNU 262 O-RING (TOP)
ASNU 264 FILTER
ASNU 263 SPLIT SPACER
ASNU 265 NYLON SEALING BUSH
INJECTOR ADAPTER ASNU 56
Tests injectors with filter installed
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 22222222
MITSUBUSHI HITACHI - GDI
Gasoline Direct Injection Use Test Adapter 2-15536
with filter in
TO TEST: REMOVE TOP O'RING & SPLIT WASHER.
REPLACE WITH 2 x 2-15004 & USE 2-15536 COUPLING
ASNU 234 O-RING
ASNU 20 FILTER
INJECTOR ADAPTER 2-15536
Test injectors with filter installed
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 23232323
FORD - GDI BOSCH
Gasoline Direct Injection Use Test Adapter 2-15536
with filter in
ASNU 14 O-RING (TOP)
2-15001 FILTER
ASNU 265 NYLON SEALING BUSH
INJECTOR ADAPTER 2-15536 (Tests injectors with filter installed)
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 24242424
VW - GDI Bosch
Gasoline Direct Injection Use Test Adapter 2-15536
with filter in
ASNU 14 0-RING (TOP & BOTTOM)
2-15001 FILTER
ASNU 265 NYLON SEALING BUSH
INJECTOR ADAPTER 2-15536 (Tests injectors with filter installed)
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 25252525
FORD - USA BOSCH
Use Test Adapter 2-15536 with filter in
Use 2-15640 Adapter Plate in fuel rail for testing
ASNU 14 BOTTOM O-RING
2-15001 FILTER
USE 2-15640 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS
ASNU 239 BOTTOM 0-RING
Test Adapter 2-15511 tests injectors with hose & filter removed
INJECTOR ADAPTER 2-15536
(Tests injectors with filter installed)
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 26262626
CITROEN PEUGEOT RENAULT
FIAT Weber & Siemens
Use Test Adapter 2-15536 with filter in Use 2-15640 Adapter Plate in fuel rail for
testing
ASNU 14 O-RING (TOP & BOTTOM)
ASNU 04 FILTER
USE 2-15640 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS
Test Adapter 2-15511 tests injectors with hose & filter re-
moved
INJECTOR ADAPTER 2-15536
(Tests injectors with filter installed)
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 27272727
VW / AUDI SIEMENS
Use Test Adapter 2-15536 with filter in
ASNU 14 O-RING (TOP & BOTTOM)
ASNU 03 FILTER
PINTLE CAPS ARE NOT REMOVABLE
Test Adapter 2-15511 tests injectors with hose & filter removed
INJECTOR ADAPTER 2-15536
(Tests injectors with filter installed)
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 28282828
VW / AUDI SIEMENS
Use Test 2-15536 with filter in
ASNU 14 O-RING (TOP & BOTTOM)
2-15001 FILTER
PINTLE CAPS ARE NOT REMOVABLE
Test Adapter 2-15511 tests injectors with hose & filter removed
INJECTOR ADAPTER 2-15536
(Tests injectors with filter installed)
WIRING HANESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 29292929
FORD USA SIEMENS
Use Test Adapter 2-15536 with filter in
ASNU 14 0-RING (TOP & BOTTOM)
2-15001 FILTER
PINTLE CAPS ARE NOT REMOVABLE
INJECTOR ADAPTER 2-15536
(Tests injectors with filter installed)
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 30303030
CHRYSLER USA
SIEMENS Use Test Adapter 2-15536
with filter in
ASNU 14 0-RING (TOP & BOTTOM)
2-15001 FILTER
PINTLE CAPS ARE NOT REMOVABLE
INJECTOR ADAPTER 2-15536
(Tests injectors with filter installed)
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Top Feed Injectors
Section 3 Page Section 3 Page Section 3 Page Section 3 Page 31313131
BMW / KIA Air Assisted
Sagem Use Tests Adapter 2-15536
with filter in
ASNU 14 O-RING (TOP)
2-15001 FILTER
Test Adapter 2-15511 tests injectors with hose & filter removed
ASNU 21 O-RING (BOTTOM)
INJECTOR ADAPTER 2-15536
(Tests injectors with filter installed)
WIRING HARNESS 2-15502
Universal Injector
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 1111
WEBER / ROCHESTER LARGE
MONO POINT / SINGLE POINT TBI (USA)
Use Test Adapter 2-15518(single injector block
includes custom harness) or
Use Test Adapter 2-15598 (twin injector block includes
custom harness)
2-15110 DUST CAP
2-15031 SIDE FEED FILTER
ASNU 60F HOUSING WASHER
ASNU 60C WEBER FILTER
2-15301 ROCHESTER FILTER
2-15320 HOUSING O-RING
ASNU 60B WEBER BOTTOM O-RING
2-15319 ROCHESTER BOTTOM O-RING
ASNU 60J DUST SEAL
2-15518 ADAPTER BLOCK
2-15598 ADAPTER BLOCK
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
VARIOUS APPLICATIONS
WEBER / ROCHESTER SMALL
MONO POINT / SINGLE POINT
TBI (USA)
Use Test Adapter 2-15519 (single
injector block includes custom
harness) or Use Test Adapter 2-15632 4
injector block (includes custom har-
ness)
2-15110
CAP
2-15307
O-RING (ROCHESTER)
2-15093
WEBER FILTER
ASNU 64F
ROCHESTER FLTER
ASNU 64C
WEBER FILTER
ASNU 64E
ROCHESTER FILTER
ASNU 64B
O-RING
2-15519
ADAPTER BLOCK
2-15632
ADAPTER BLOCK & HARNESS
GM TBI MULTEC 700
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 2222
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
CHRYSLER
CFI
SINGLE UNIT
BOSCH
(LONG VERSION)
Use Test Adapter 2-15597 (single block)
or
Test Adapter 2-15528(twin block)
2-15065
FILTER
2-15321
O-RING (LOWER)
2-15669
2-15528
(twin block w/harness)
2-15597
(single block w/harness)
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 3333
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
NISSAN / SUBARU
SINGLE POINT
Use Test Adapter 2-15523
(single block)
MULTI POINT
Use Adapter
2-15608 (6 inj. block)
Connect injectors with universal
harness 2-15502
2-15077
FILTER
2-15019
PINTLE CAP
2-15048
SEAL
(Nissan)
2-15049
PLASTIC WASHER
2-15673
O-RING
2-15635
CAP
2-15674
LOWER O-RING
2-15523
SINGLE BLOCK
Use 2-15608
4 INJ. BLOCK
2-15608
6 INJ. BLOCK
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 4444
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
VARIOUS APPLICATIONS
BOSCH
MONOPOINT / SINGLE POINT
TBI (USA)
Use Test Adapter 2-15524
(single block includes custom
harness)
2-15032
O-RING (UPPER)
2-15043
O-RING (LOWER)
2-15066
CLIP (UPPER)
2-15672
FILTER (NEW TYPE) (UPPER)
2-15065
FILTER (UPPER)
2-15093
FILTER (LOWER)
2-15524
ADAPTER BLOCK WITH CUSTOM
HARNESS
2-15110
DUST CAP
2-15671
PINTLE CAP
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 5555
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
VARIOUS APPLICATIONS
BOSCH, WEBER, DENSO,
SIEMENS
Use Test Adapter 2-15530 (block
holds 4 injectors)
or
Test Adapter 2-15635
(block holds 6 injectors for
Chrysler 3.5L)
Connect injectors with universal
harness 2-15502
2-15032
O-RING TOP
2-15679
O-RING BOTTOM
2-15065
FILTER
WEBER & SIEMENS INJECTORS
HAVE NO REMOVABLE
PINTLE CAPS
2-15659
SINGLE SPRAY PINTLE CAP
BOSCH
2-15070
TWIN SPRAY
PINTLE CAP
DENSO
2-15530
ADAPTER BLOCK
(Holds 4 injectors - Ford Zeta
2-15635
ADAPTER BLOCK
(Holds 6 injectors - Jaguar &
Chrysler 3.5L)
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 6666
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
NISSAN
&
TOYOTA
Use Test Adapter 2-15598
(block holds 2 injectors,
includes custom harness)
2-15682
O-RING (UPPER)
2-15114
CAP
2-15612
O-RING (LOWER)
ASNU 102C
FILTER
2-15607
ADAPTER BLOCK
Side Feed Injectors
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 7777
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
NISSAN JECS
Use Test Adapter 2-15609
(block holds 6 injectors)
Connect injectors with
universal harness 2-15502
2-15039
TOP O-RING
2-15613
BOTTOM O-RING NISSAN
2-15685
BOTTOM O-RING TOYOTA
2-15053
TOP O-RING Nissan / Toyota Housing
seal (large)
2-15050
TOP O-RING Nissan /
Toyota Housing seal (small)
2-15052
TOP O-RING Nissan / Toyota
Housing seal (medium)
ASNU 103C
FILTER
ASNU 103E
PINTLE CAP
2-15685
FILTER / SPACER
2-15609
ADAPTER BLOCK
2-15613
BLANKING OFF PLUG
2-15110
DUST CAP
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 8888
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
TOYOTA JECS
Use Test Adapter 2-15606
(block holds 4 injectors)
Connect injectors with universal
harness 2-15502
2-15058
O-RING
2-
15060
O-RING
2-15687
O-RING
REPLACEMENT FILTER
CURRENTLY NOT
AVAILABLE DO NOT REMOVE
FILTER
2-15059
INSULATOR
2-15110
CAP
2-15606
TWIN ADAPTER BLOCK
2-15502
UNIVERSAL INJECTOR
WIRE HARNESS
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 9999
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
NISSAN
JECS
Use Test Adapter 2-15529
(block holds 4 injectors)
Connect injectors with
universal harness 2-15502
2-15029
O-RING (UPPER)
2-15689
O-RING (LOWER)
REPLACEMENT FILTER NOT CURRENTLY
AVAILABLE DO NOT REMOVE FILTER
2-15114
CAP
2-15529
ADAPTER BLOCK
2-15502
UNIVERSAL INJECTOR WITH HARNESS
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 10101010
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
MAZDA
NIPPON DENSO
Use Test Adapter 2-15634
(Injector block)
Connect injectors with universal
harness 2-15502
2-15690
TOP O-RING
2-15004
BOTTOM O-RING
REPLACEMENT FILTER CURRENTLY
NOT AVAILABLE DO NOT REMOVE
FILTER
2-15659
SINGLE SPRAY PINTLE
CAP BOSCH 2-15070
TWIN SPRAY PINTLE CAP
DENSO
2-15634
6 INJ. BLOCK
2-15613
BLANKING OFF PLUG
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 11111111
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
NISSAN
JECS
Use Test Adapter 2-15661
(4 Injector block)
Connect injectors with universal
harness 2-15502
2-15692
TOP O-RING
2-15693
BOTTOM O-RING
REPLACEMENT FILTER CURRENTLY NOT
AVAILABLE DO NOT REMOVE FILTER
2-15661
4 INJ. BLOCK
2-15502
UNIVERSAL INJECTOR WIRE HARNESS
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 12121212
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
HONDA CIVIC
KEIHIN
Use Test Adapter 2-15636
(double block)
Connect injectors with universal harness
2-15502
2-15029
TOP O-RING
2-15030
MIDDLE O-RING
2-15040
UPPER SEAL
2-15110
CAP
2-15636
TWIN ADAPTER BLOCK
2-15502
UNIVERSAL INJECTOR WIRE
HARNESS
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 13131313
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
HONDA CIVIC
KEIHIN
Use Test Adapter 2-15636
(double block)
Connect injectors with universal harness
2-15502
2-15029
TOP O-RING
2-15030
MIDDLE O-RING
2-15036
BOTTOM O-RING
2-15040
UPPER SEAL
2-15110
CAP
2-15636
TWIN ADAPTER BLOCK
2-15502
UNIVERSAL INJECTOR WIRE
HARNESS
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 14141414
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
FORD CFI
SINGLE UNIT
BOSCH
Use Test Adapter 2-15597
(single block) or
Test Adapter 2-15528 (block)
2-15309
O-RING (LOWER)
2-15314
O-RING (UPPER)
ASNU 61C
FILTER
2-15597
ADAPTER BLOCK
(Includes Custom Harness)
2-15528
ADAPTER BLOCK
(Includes Custom Harness)
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 15151515
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
NISSAN CFI
SINGLE UNIT
BOSCH
Use Test Adapter 2 2-15597
(single block) or
Test Adapter 2-15528 (twin block)
2-15322
O-RING (UPPER)
2-15306
FILTER
2-15321
O-RING (LOWER)
2-15597
(single block w/harness)
2-15528
(twin block w/harness)
2222----15669156691566915669 CUPCUPCUPCUP (Bosch Style Only)(Bosch Style Only)(Bosch Style Only)(Bosch Style Only)
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 16161616
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
CHRYSLER
CFI
SINGLE UNIT
BOSCH
(LONG VERSION) 2-15597
(single block)
or
Test Adapter 2-15528
(twin block)
2-15065
FILTER
2-15322 O-RING (UPPER)
2-15321 O-RING (LOWER)
2-15669
2-15597 (single block w/harness)
2-15528 (twin block w/harness)
2222----15669156691566915669 CUPCUPCUPCUP (Bosch Style Only)(Bosch Style Only)(Bosch Style Only)(Bosch Style Only)
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 17171717
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Side Feed Injectors
SUZUKI
MONOPOINT
DENSO
Use Test Adapter 2-15525
(single block)
2-15027
O-RING
2-15026
O-RING
REPLACEMENT FILTER CURRENTLY
NOT AVAILABLE DO NOT REMOVE
FILTER
2-15114
DUST CAP
2-15525
ADAPTER BLOCK WITH CUSTOM HARNESS
Section 4 Page Section 4 Page Section 4 Page Section 4 Page 18181818
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Vortec Injectors
Use Test Adapter 2-15631 (tests &
cleans complete assembly )
Connect injectors with 2-15629
Universal Harness
GM VORTEC
4.3L V-6 & 5.7L CPI
SPRAYING SECURING FLOWING
2-15631 Test Adapter Kit
Includes plastic cleaning tray (see below) for ultrasonic cleaning of individual
injector coils & frame mount shown below.
Injector components not available at this time
2-15631
Test Adapter Stainless Steel
Frame in Anodized Aluminum
Rail Complete with cleaning
tray
2-15660
Cleaning Tray
2-15629
Vortec Harness
Section 5 Page Section 5 Page Section 5 Page Section 5 Page 1111
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
GM VORTEC
4.3L V-6 CPI
MODELS 92-95
Use Test Adapter 2-15630
(tests complete assembly)
ASNU 108A
O-RING Early style GM Vor-
tex 4.3L
ASNU 108B
O-RING Early style GM Vor-
tex 4.3L
ASNU 108C
O-RING Early style GM
Vortex 4.3L
ASNU 108D
O-RING Early style GM Vor-
tex 4.3L
ASNU 108E
O-RING Early style GM
Vortex 4.3L
2-15630
Test Adapter Kit
ASNU 108T
Cleaning Tray
(optional)
Vortec Injectors
Section 5 Page Section 5 Page Section 5 Page Section 5 Page 2222
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Accessories, Components and Adaptors
2-15627
BIO-CLEAN ULTRASONIC CLEANING FLUID
5 LITER BOTTLE
2-15593
FLOW-RITE
CALIBRATION FLUID
5 LITER BOTTLE
ASNU 46
ADAPTER COUPLING HITACHI INJECTORS
USED ON AUDI QUATTRO
2-15532
8MM FEMALE ADAPTER COUPLING FOR
8MM MALE COLD START INJECTOR
2-15533
10MM MALE ADAPTER COUPLING
FOR 10MM FEMALE COLD START
INJECTOR
2-15534
ADAPTER COUPLING COLD START
INJECTOR HOSE TYPE (12-13MM)
2-15535
10MM FEMALE ADAPTER COUPLING
FOR 10MM MALE COLD START
INJECTOR
2-15511
ADAPTER COUPLING TOP FEED MULTI-
PORT INJECTORS WITH FILTER
BASKET REMOVED
2-15512
SMALL O-RING FOR 2-15511 COUPLING
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 1111
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
2-15513
LARGE (TOP) O-RING FOR ASNU ADAPTER
COUPLING
2-15514
8MM MALE ADAPTER COUPLING FOR 10MM
FEMALE CIS (K-JET)
2-15515
12MM FEMALE ADAPTER COUPLING
FOR 12MM MALE CIS (K-JET)
ASNU 56
ADAPTER COUPLING FOR SLIM TOP
SIEMENS GDI INJECTORS TESTS INJEC-
TORS WITHOUT REMOVING INLET FILTER
2-15536
ADAPTER COUPLING BOSCH, LUCAS,
WEBER, MARELLI, SIEMENS TESTS
INJECTORS WITHOUT REMOVING INLET
FILTER
2-15537
ADAPTER COUPLING TESTS
MULTIPORT INJECTORS WITH FUEL
HOSE INSTALLED
2-15538
ADAPTER COUPLING SLIM TYPE DENSO
TESTS INJECTORS WITHOUT REMOVING
INLET FILTER
2-15502
UNIVERSAL INJECTOR HARNESS
CONNECTS MOST MULTIPORT INJECTORS
2-15610
REPAIR KIT FOR MAIN ASNU
INJECTOR HARNESS
NOT AVAILABLE
Accessories, Components and Adaptors
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 2222
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
2-15518
ADAPTER BLOCK
GM TBI MAXI WITH CUSTOM HARNESS
(single block - use 2-15598 for double
block)
2-15519
ADAPTER BLOCK
GM TBI MULTEC WITH CUSTOM HARNESS
(single block - use 2-15632 for Quad
Block)
2-15526
ADAPTER BLOCK
FORD CFI - HOLLEY SPI CHRYSLER &
BOSCH WITH CUSTOM HARNESS
(single block - use 2-15528 for double
block)
2-15522
ADAPTER KIT
MITSUBISHI MPI WITH CUSTOM HAR-
NESS
(Tests 2 injectors)
2-15529
ADAPTER BLOCK
NISSAN / SUBARU SPI
(Tests 4 injectors)
2-15524
ADAPTER BLOCK
BOSCH SPI
(Tests 1 injector)
2-15525
ADAPTER BLOCK
SUZUKI SPI
(Tests 1 injector)
2-15530
ADAPTER BLOCK
FORD ZETA MPI / SPI
(BOSCH / WEBER / SIEMENS / DENSO)
(Tests 4 injectors)
ADAPTER BLOCK
NISSAN / SUBARU SPI
(Tests 1 injector)
Injector Index
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 3333
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Accessories, Components and Adaptors
FILTER BASKET
REMOVAL TOOL
T-HANDLE TYPE
2-15638
CUSTOM NYLON COVER
FOR ASNU MACHINE
NLA
"FOAMEX"
WEATHERPROOF SIGN
COMPONENT ASSTS
2-15100 / FILTERS & CAPS
2-15200 /O'RINGS-SEALS
2-15300 /MONOPOINT KIT
2-15639
PINTLE CAP & FILTER BASKET
ASSEMBLY TOOL
2-15594
PINTLE CAP
REMOVAL TOOL
GUN TYPE
2-15595
FILTER REMOVAL TOOL
GUN TYPE
2-15510
RUBBER BENCH MAT
2-15521
PLASTIC
RAIL HOLDER
DISCONTINUED DISCONTINUED
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 4444
FILTER BASKET
REMOVAL TOOL
T-HANDLE TYPE
2-15638
CUSTOM NYLON COVER
FOR ASNU MACHINE
NLA
"FOAMEX"
WEATHERPROOF SIGN
COMPONENT ASSTS
2-15100 / FILTERS & CAPS
2-15200 /O'RINGS-SEALS
2-15300 /MONOPOINT KIT
2-15639
PINTLE CAP & FILTER BASKET
ASSEMBLY TOOL
2-15594
PINTLE CAP
REMOVAL TOOL
GUN TYPE
2-15595
FILTER REMOVAL TOOL
GUN TYPE
2-15510
RUBBER BENCH MAT
2-15521
PLASTIC
RAIL HOLDER
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
2-15640
WEBER / SIEMENS
TOP FEED MULTIPOINT
"MINI PECO INJECTOR"
ADAPTER PLATE
2-15605
INJECTOR SERVICE
REPORT PAD
50 SELF CARBON
(ENGLISH ONLY)
2-15531
TBI ADAPTER RING
USE W/ 2-15507 CRADLE
LARGE TBI INJECTORS
(GM MAXI)
2-15601
TBI ADAPTER RING
USE W/ 2-15507 CRADLE SMALL TBI IN-
JECTORS
GM MULTEC / DAEWOO
2-15520
CIS (K-JET) INJECTOR
CLEANING TRAY
2-15641
SIDE FEED INJECTOR CLEANING
TRAY
(SHALLOW)
ASNU 1992 onward
2-15600
ASNU UPTO 1992 (DEEP)
2-15642
CLEANING TRAY
PECO INJECTOR
2-15598
ADAPTER BLOCK
GM TBI MAXI
(Tests 2 injectors, includes custom harness)
2-15607
ADAPTER BLOCK
NISSAN / TOYOTA 2 WIRE
(Tests 2 injectors, includes blanking off
plug & custom harness
Accessories, Components and Adaptors
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 5555
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Injector Index
2-15609
ADAPTER BLOCK
NISSAN JECS
(Tests 6 injectors)
2-15606
ADAPTER BLOCK
TOYOTA JECS MPI
PREVIA / TARAGO
(Tests 6 injectors)
ASNU 105
ADAPTER BLOCK
NISSAN PATHFINDER / NAVARA
(Tests 4 injectors)
2-15608
ADAPTER BLOCK
NISSAN / SUBARU SPI
(Tests 6 injectors)
2-15634
ADAPTER BLOCK
MAZDA / DENSO
(Tests 6 injectors)
2-15630
ADAPTER GM VORTEC 4.3 EARLY VERSION
(Tests complete assembly)
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 6666
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Injector Index
2-15631
ADAPTER KIT GM VORTEC 4.3L & 5.7L LATE VERSION
(Tests complete assembly includes cleaning tray)
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 7777
Echlin Part Numbers 2-15630 and 2-15631 Adapters comes complete with 2-15629 harness and plastic cleaning tray for ultrasonic cleaning of individual injector coils.
2-15629 Harness assembly is a available separately.
The later GM Vortec (late) system is a Multi Point operation with 6 or 8 individual injectors mounted in the housing, allowing either a simultaneous or sequential injection delivery.
The fuel is pressurized into the injector housing and as the injector is electronically opened, the fuel is pressure fed into a nylon delivery tube. At the end of the tube is a pressure poppet valve. The poppet valve sits in the inlet manifold and can be subject to extremely harsh conditions that may affect the per-formance of the valve. The opening and closing of the poppet valve is controlled by pressure and deter-
mines the fuel distribution, fuel atomization and the fuel delivery to each cylinder. The is therefore very important to examine the performance of this system, both before servicing (to un-derstand the cause of the engine problem) and after, to ensure the cause of the problem had been elimi-
nated and that the system is working properly.
SPRAYING SECURING FLOWING
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Injector Index
2-15631
ADAPTER KIT GM VORTEC 4.3L & 5.7L LATE VERSION
(Tests complete assembly includes cleaning tray)
2-15635
ADAPTER BLOCK
FORD ZETA / SIEMENS
CHRYSLER 3.5L
(Tests 6 injectors)
2-15636
ADAPTER BLOCK
HONDA CIVIC
NIKI KEIHIN
(Tests 2 injectors
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 8888
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Accessories, Components and Adaptors
2-15637
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 9999
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Accessories, Components and Adaptors
Section 6 Page Section 6 Page Section 6 Page Section 6 Page 10101010
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Numerical Parts Listing Echlin # DESCRIPTION
2-15001 Standard Injector Filter Basket with Brass Collar
2-15002 K-Jetronic (CIS) Injector O'Ring
2-15003 BMW Finned Pintle Insulator Cap - Yellow
2-15004 Standard L-Jetronic O'Ring - 15mm - Black
2-15006 L-Jetronic / Nissan / GM Injector Head Seal - Medium
2-15007 Nippon Denso Injector Rail Dust Seal (50)
2-15008 O'Ring Toyota Bottom Small Flat
2-15009 Toyota / Mazda / Nippon Denso Top O'Ring Seal
2-15010 D-Jetronic Injector O'Ring Head Seal - Small
2-15011 DUST SEAL OD 27MM ID22MM WIDTH 8MM
2-15012 Bosch L-Jetronic Injector Spacer - 2mm
2-15014 Nikki Injector Head Seal
2-15015 Nikki Injector Top O'Ring
2-15016 Honda Injector Grommet
2-15017 Bosch Trumpet End Pintle Cap
2-15018 Bosch/Nippon Denso Standard Pintle Insulator Cap
2-15019 L-Jetronic Standard Pintle Insulator Cap-Black
2-15020 D-Jetronic Pintle Insulator Cap-Black 18mm
2-15021 CAP, PKG TOYOTA PINTLE
2-15022 24 Compartment tray
2-15024 FERRULE, PKG
2-15026 O-RING, PKG INJECT LOW
2-15027 O-RING, PKG INJECT UPP
2-15029 NA FROM ACE
2-15029 O-RING, PKG INJECT UPP
2-15030 O-RING, PKG INJECT LOW
2-15031 SIDE FEED FILTER, PMAXI TBI INJ
2-15032
2-15032 O-RING, PKG INJECT UPP
Section 7 Page Section 7 Page Section 7 Page Section 7 Page 1111
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Numerical Parts Listing 2-15033 COLLAR, PKG INJECTOR
2-15035 Pintle Cap
2-15036 O-RING, PKG AUX INJECT
2-15039 Nissan/Toyota Side Feed Injector - Top- O-Ring
2-15040 SEAL, PKG INJECT UPPER
2-15041 SEAL, PKG INJECTOR
2-15042 CLIP, PKG INJECTOR
2-15043 O-RING, PKG INJECT LOW
2-15048 SEAL, PKG INJECTOR
2-15049 SEAL, PKG INJECTOR
2-15050 SEAL, PKG INJECTOR
2-15051 SEAL, PKG INJECTOR
2-15052 SEAL, PKG INJECTOR
2-15053 SEAL, PKG INJECTOR
2-15055 INSULATOR, PKG TOYOTA
2-15056 INSULATOR, PKG TOYOTA
2-15058 INSULATOR, PKG TOYOTA
2-15059 INSULATOR, PKG TOYOTA
2-15060 O-RING, PKG INJECTOR
2-15061 O-RING, PKG INJECTOR
2-15062 O-RING, PKG INJECTOR
2-15064 FILTER, HONDA INJECTOR
2-15065
2-15065 Screen Filter 25pk
2-15066 CLIP, SPI BOSCH
2-15067 CAP, MAZDA PINTLE
2-15068 CAP, FORD LRG PINTLE
2-15069 CAP, FORD SMALL PINTLE
2-15070 CAP, FORD 2HOLE PINTLE
Page Page Page Page 2222
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Numerical Parts Listing 2-15071 O-RING, TOYOTA
2-15072 CAP, WEBER PINTLE
2-15074 Fuel Injector Pintle Cap
2-15075 SPACER, NISSAN INJECTOR
2-15076
2-15076 Fuel Injector Filter Screen
2-15077 Fuel Injector Filter Screen
2-15091 FUEL INJECTOR HOSE
2-15092 SPACER, ROCH INJECTOR
2-15093 FILTER, TBI INJECT LOW
2-15094 Inj. O-Ring 25pk
2-15095 CAP, PINTLE L-JET
2-15096 VAPOR CAP 2-HOLE
2-15097 CAP, DENSO 2HOLE VAPOR
2-15098 CAP, 2HOLE INSULATOR
2-15099 CAP, FORD INSULATOR
2-15100 Multipoint Fuel Injection Kit 2 - O'Rings, Rubber Seals & Dust Caps.
2-15101 BMW CIS (K-Jetronic) Injector O'Ring
2-15102 Mazda Injector O'Ring - Lower Mazda Injector Head Seal
2-15103 Rail Washer 100pk
2-15104 Mazda Injector O'Ring - Lower Mazda Injector Head Seal
2-15106 Mazda Grommet
2-15107 Mazda Air Bleed Socket O'Ring
2-15108 Cadillac Fuel Rail Grommet
2-15109 Audi CIS (K-Jetronic) Injector Seal
2-15110 Injector Protective Cap - Small
2-15111 Injector Protective Cap Rail Fitted Injector Protective Dust Cap
2-15112 Injector Protective Cap
2-15113 Injector Protective Cap Hose Fitted Injector Protective Dust Cap
2-15114 Injector Protective Cap - Large
Page Page Page Page 3333
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Numerical Parts Listing
2-15300 Singlepoint/Monopoint Fuel Injection Kit 3 - Fiter Baskets, O'Rings & Seals.
2-15301 Rochester bottom filter basket
2-15302 Ford Injector O'Ring - Upper
2-15304 Ford Injector Mounting - Lower O'Ring
2-15305 Hitachi InjectorO'Ring - Small
2-15306 Hitachi Injector Filter Screen
2-15306 Bosch/Chrysler / Hitachi Tbi Filter Screen
2-15307 Rochester TBI Model 700 Injector O'Ring - Upper
2-15308 Inj. Washer 25pk
2-15309 Holley Tbi Injector O'ring - Lower
2-15310 Nissan Injector O'Ring
2-15311 Rochester TBI Larger Filter Screen (50)
2-15312 Ford Injector Filter Screen
2-15313 Bosch Injector O'Ring BLACK (50)
2-15314 Holley Tbi Upper O'ring
2-15315 Rochester Injector Housing Dust Seal
2-15316
2-15316 Niisan Single Point Injector
2-15317 Injector Body Support Rubber - Thick(SQUARE CORNERS)
2-15318 Bosch Injector O'Ring
2-15319 Rochester TBI Large - Lower O'Ring
2-15320 Rochester/Bendix/Weber small TBI O'Ring - Upper
2-15321 Bosch/Chrysler / Hitachi Tbi O'ring - Lower
2-15322 Bosch/Chrysler / Hitachi Tbi O'ring - Upper
2-15323 Chrysler / Hitachi Injector O'Ring
2-15500 ASNU Ultrasonic Injector Cleaner & Flow Bench
2-15502 Universal Injector Harness - Connects most multiport Injectors
2-15503 Plastic Moulded Flow Display Window
2-15504 Calibration Fluid Tank Cover
2-15506 Power Cord USA - 3metre
Page Page Page Page 4444
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Numerical Parts Listing 2-15507 Ultrasonic Bath Injector Cradle
2-15508 Steel Braided Fuel Hose Complete with Quick Coupler
2-15509 Glass Measuring Cylinder - MM
2-15510 Rubber Bench Mat
2-15511 Adaptor Coupling Top Feed Multiport Injectors w/filter basker removed
2-15512 Small O-Ring for 2-15511 Coupling
2-15513 Large(TOP) O-Ring for 2-15511 Adaptor Coupling
2-15514 8mm Male Adaptor for 10MM Female CIS (K-Jet)
2-15515 12mm Female Adaptor Coupling for 12MM Male CIS (K-Jet)
2-15518 Adaptor Black GM TBI Maxi with Custom Harness (single block / use 2-15598 for double block)
2-15519 GM TBI Multec w/Custom Harness (single block / use 2-15632 for Quad block)
2-15520 CIS K-Jet Cleaning Tray
2-15521 Plastic Fuel Rail Holder
2-15522 Adaptor Kit Mitsubishi MPI w/Custom Harness(Tests two injectors) ECI Two
2-15523 Adaptor Block Nissan / Subaru SPI (tests 1 injector)
2-15524 Adaptor Block Bosch SPI (tests 1 injector)
2-15525 Adaptor Block Suzuki SPI (tests 1 injector)
2-15526 Adaptor Block Ford CFI - Holly SPI Chrysler & Bosch w/Custom Harness (single block / use 2-15528 for double block)
2-15527 Adaptor Block Bosch / Holly / Nissan / Ford (tests 2 injectors)
2-15528 Adaptor Block Bosch / Holly / Nissan / Ford (tests 2 injectors)
2-15529 Adaptor Block Subaru / Nissan SPI (tests 4 Injectors)
2-15530 adaptor Block Ford Zeta MPI /SPI (Bosch / Weber / Siemens / Denso) (tests 4 injectors)
2-15531 TBI Adaptor Ring - use w/2-15507 Cradle large TBI Injectors (GM Maxi)
2-15532 8mm Female Adaptor For 8mm Male Cold Start Injector
2-15533 10mm Male Adaptor for 10mm Female Cold Start Injector
2-15534 Adaptor Coupling Cold Start Injector Hose Type 12-13MM
2-15535 10mm Female Adaptor Coupling for 10MM Male Cold Start Injector
2-15536 Adaptor Coupling Bosch, Lucas, Weber, Marelli, Siemens - Tests Injector w/o
2-15537 Adaptor Coupling Tests Multiport Injectors with Hose Attached
2-15538 Adzaptor Coupling Slim Tyope Denso - Tests Injectors w/o removing inlet filter
Page Page Page Page 5555
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Numerical Parts Listing 2-15539 Calibration Fluid In-Line Fuel Filter
2-15540 Calibration Fluid In-Tank Pre-pump Filter
2-15562 Ultrasonic Tank Complete Assembly
2-15593 Flow Rite calibration fluid
2-15594 Pintle Cap Removal Tool - Hand Gun Type
2-15595 Filter Basket Removal Tool - Hand Gun Type
2-15597 Adaptor Block Ford CFI - Holly SPI Chrysler & Bosch w/Custom Harness (single block / use 2-15528 for double block)
2-15598 GM-TBI Large (TBI) Dual Injector Manifold and Harness Kit
2-15599 ASNU Main Board-Service Exchange ($750 Core)
2-15600 Side Feed Injector Cleaning Tray (Deep)
2-15601 TBI Adaptor Ring - use w/2-15507 Cradle Small TBI Injectors (GM Multec / Dae-woo)
2-15602
2-15603 Quick Reference Wall Chart - English
2-15604 Instruction Manual
2-15605 Injector Service Report Pad (50 Pages per Pad)
2-15606 Toyota Tarago/Previa Quad Injector Manifold Kit
2-15607 Nissan / Toyota 2 Wire Dual Injector Manifold and Harness Kit
2-15608 Subaru / Nissan Maxima 6 Injector Manifold Kit
2-15609 Nissan Navara Multipoint Six Injector Manifold Kit
2-15610 Repair Lits for Main Injector Harness
2-15612 Injector Blank - Nissan / Toyota 2 Wire
2-15613 Injector Blank - Nissan Navara Multipoint
2-15627 Bio-Clean Ultrasonic Cleaneing Fluid
2-15629 Universal Injector Harness for Vortec System
2-15629 Wiring Harness for Vortec
2-15630 Adaptor Block GM Vortec 4.3 - Early Version
2-15631 Adaptor Kit GM Vortec - 4.3 & 5.7 Later Version
2-15632 Adaptor Block GM TBI Multec 700 ( tests 4 injectors) includes harness
2-15634 Adaptor Block Mazda / Denso (tests 6 injectors) 2-15635 Adaptor Block Ford Zeta / Siemens Chrysler 3.5 (tests 6 injectors)
Page Page Page Page 6666
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Numerical Parts Listing 2-15636 Adaptor Block Honda Civic / Nikki Keihen (tests 2 injectors)
2-15637 Custom Harness Delphi Pin Type Connectors (tests up to 8 injectors)
2-15638 Injector Nylon Cover for 2-15500 ASNU Machine
2-15639 Injector Filter Basket & Pintle Cap Assembly Tool
2-15640 Adaptor Plate for Weber / Siemens (Mini Peco Injector)
2-15641 Side Feed Injector Cleaning Tray (Shallow) 1992 onward / 2-15600 up to 1992 (Deep)
2-15642 Perspex cleaning tray for K-jet & Weber/Sieman Mini Peco injectors
2-15643 Magnetically Couples Electric High Performance Pump
2-15644 High Performance Fuel Rail Top Feed Injectors (tests 8 injectors) includes extension bolts for long GDI injectors
2-15645 Lid for ultra-sonic tank
2-15646 GDI injector Drive box
2-15647 Mercury Optimax
2-15648 Filter removal tool replacement bit
2-15649 Late Bosch Pintle
2-15650 Late Bosch Pintle
2-15651 Late Bosch Pintle
2-15652 Late GM Pencil Pintle
2-15653 Top O-Ring Retainer
2-15654 GM Vortex 4.3L V5 CPI Filter
2-15655 Pintle Cap Holden
2-15656 Pintle Cap Ford AU
2-15660
2-15660 NA FROM ACE
2-15661 NA FROM ACE
2-15662 1MM Spacer
2-15663 Pintle Cap; Ribbed for BNW w/4MM hole for 24V engine
2-15669 SPI/TBI Plastic Clip Cover
2-15671 Pintle Cap
2-15671 Pintle Cap- Bosch Cone Type Single Point Injector
2-15672
Page Page Page Page 7777
Copyright 2009 ASNU Corporation All Rights Reserved
IMPORTANT
Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used
only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.
Match & select the components with the injector. Ensuring they are suitable for use.
Numerical Parts Listing
2-15672 NA FROM ACE
2-15673 Upper O-Ring - Nissan SPI / MPI
2-15674 O-RING, PKG INJECTOR
2-15679 14.5 MM O-RING Brown
2-15682 Hitachi InjectorO'Ring Seal - Upper Large
2-15685 O-RING, PKG INJECTOR
2-15687 NA FROM ACE
2-15689 O-RING, PKG
2-15690 Top O-Ring for Mazda Side Feed Injectors
2-15692 NA FROM ACE
2-15693 NA FROM ACE
2-15698 Pintle Cap - Large Hole Type for "V" Spray Injectors
TBA Brass / Plastic Filter Basket for Lucas Injectors
TBA Brass / Wire Filter Basket for Weber Injectors
Page Page Page Page 8888