ec210b-17.pdf
-
Upload
gian-carlos-levano-canales -
Category
Documents
-
view
214 -
download
0
Transcript of ec210b-17.pdf
-
8/15/2019 ec210b-17.pdf
1/13
CLICK THE VOLVO-LOGO THE LOWER RIGHT CORNTO RETURN TO THIS MEN
MAINMENU
Hydraulic Oil Tank EC210B-17-01Air Breather EC210B-17-02Fuel Tank EC210B-17-03Swing Ring Gear EC210B-17-04Bucket Clearance Adjustment EC210B-17-05Under Carriage and Track Link EC210B-17-06Measuring Method of Track Link Pitch EC210B-17-07Upper Roller EC210B-17-08Lower Roller EC210B-17-09
Sprocket EC210B-17-10Idler EC210B-17-11Recoil Spring EC210B-17-12
17 MISCELLANEOUS
http://ec210b-main.pdf/http://ec210b-main.pdf/http://ec210b-main.pdf/
-
8/15/2019 ec210b-17.pdf
2/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-01
Hydraulic Oil Tank
SIDEDOOR
FUELTANK
-
8/15/2019 ec210b-17.pdf
3/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-02
Air Breather
Hydraulic oil tank
-
8/15/2019 ec210b-17.pdf
4/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-03
Fuel Tank
HYD.TANK
TOOLBOX
-
8/15/2019 ec210b-17.pdf
5/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-04
Swing Ring Gear
"S" mark(inner race) Plug(outer race)
SECTION A-A
A
A
-
8/15/2019 ec210b-17.pdf
6/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-05
Bucket Clearance Adjustment
A
Section A-A
Detail B
Max. 2.0mm Gap
Shim
B
A
-
8/15/2019 ec210b-17.pdf
7/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-06
Under Carriage and Track Link
4
3
10 S02776C
8
6 7
2
5
9
1 unit : mm (in)
No. Check item Standard size Repair limit Remedy
1 Link pitch 190.3 (7.5) 194.3 (7.65) Turn or replace pin andbushing2 Outer diameter of bushing 59 (2.32) 53 (2.09)
3 Height of grouser (shoe) 26 (1.02) 16 (0.63) Lug welding or replace
4 Height of link 105 (4.13) 97 (3.82) Replace or replace
5 Clea rance of li nk andbushing
Standardsize
Tolerance Clearance Replace with largerbushingShaft Hole Standard
sizeRepair limit
59 (2.32) +0.040
–0.16 –0.23
–0.16~ –0.27
0.1
6 Clearance of link and pin 38(1.50)
+0.070
–0.22 –0.30
–0.22~ –0.37
0 .1 Replace with large r pin
7 Clea rance of li nk andmaster pin
38(1.50)
–0.26 –0.3
–0.22 –0.30
–0.08~ +0.04
– –
8 Clearance of pin andbushing
38(1.50)
+0.070
+0.80+0.30
0.23~0.80
5 Turn or replace pin andbushing
9 Clearance between links 1.4 (One side) 10 (Both sides)
10 Tightening torque of shoescrew
80 ~ 90 kgf·m (578 ~ 650 lbf·ft) Tighten
-
8/15/2019 ec210b-17.pdf
8/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-07
Measuring method of Track Link Pitch(Service Bulletin KORK112)
S01902C
TRACK PIN
TRACK PIN
TRACK PIN
Pitch of four link
Calculation of track link wear
• Track link wear = (Pitch of four track links / 4) - Initial track link pitch.
• % of wear = [Track link wear / (Repair limit - Initial track link pitch)] x 100.
• Remaining life (%) = 100 - Rate of wear (%)
< Initial track link pitch & Repair limit> (Unit : mm)
Track l ink p itch SE130LC-3 SE130LCM-3 SE210-3 SE240-3 SE280-3 SE350-3 SE450-3
Initial 171.75 190.3 203.5 216.2
Repair limit 175.75 194.3 207.5 220.2
Track link pitch EC140LC EC140LCM EC150 EC210 EC240 EC290 EC360 EC460
Initial 171.75 190.3 203.5 216.2
Repair limit 175.75 194.3 207.5 220.2
Track link pitch EC140BLC EC140BLCM EC150B EC210B EC240B
Initial 171.75 190.3
Repair limit 175.75 194.3
Track link pitch EC290B EC330B EC360B EC460B
Initial 203.5 216.2
Repair limit 207.5 220.2
-
8/15/2019 ec210b-17.pdf
9/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-08
Upper Roller
- After disassembly and assembly, fill SAE10W-30 engine oil 65cc.
S02779A
1 2
4 5
3
unit : mm (in)
No. Check item Standard size Repair limit Remedy
1 Outer diameter offlange
170 (6.7) – Reinforcementwelding or replace
2 Outer diameter oftread
140 (5.5) 130 (5.1)
3 Width of flange 83 (3.3) 71 (2.8)
4 Clearance betweenshaft and bushing
Standardsize
Tolerance Clearance Replace bushing
Shaft Hole Standardsize
Repair limit
55(5.17) +0.030 –0.090 +0.35+0.30 0.33~0.44 1.5
5 Clearance betweenroller and bushing
63(2.48)
+0.150+0.120
+0.0300
0.09~0.18
0 Replace bushing
6 Mounting screwtorque
52 ± 5 kgf·m (375 ± 36 lbf·ft)
-
8/15/2019 ec210b-17.pdf
10/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-09
Lower Roller
- After disassembly and assembly, fill SAE10W-30 engine oil 250cc.
2 4 5
3
1
S02778A
unit : mm (in)
No. Check item Standard size Repair limit Remedy
1 Outer diameter of flange 195 (7.7) Reinforcementwelding orreplace
2 Outer diameter of tread 160 (6.3) 148 (5.8)
3 Width of flange 20.5 (0.8) 13.5 (0.5)
4 Clearance betweenshaft and bushing
Standardsize
Tolerance Clearance Replace bushing
Shaft Hole Standardsize
Repair limit
70(2.76)
0 –0.03
+0.30+0.25
+0.25~0.33
1.5
5 Clearance betweenroller and bushing
78(3.07)
+0.132+0.102
+0.0460
0.056~0.132
0 Replace bushing
6 Mounting screw torque 27 3 kgf·m (195 22 lbf·ft)
-
8/15/2019 ec210b-17.pdf
11/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-10
Sprocket B
A Symbol Item Wear limit Remedy
A Wear limit of sprocket tooth profile 6 (0.24) Replace
B Width of sprocket tooth
Standard value 68 ± 1.5 (2.68 ± 0.06)
Allowable value 62 (2.44)
C Number of tooth 21 EA. –
14516700EC210BEC240B
Measuring datums
< Measuring Tool for tooth wear >
-
8/15/2019 ec210b-17.pdf
12/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-11
IdlerD
C E
B
F G
A Item Specification Allowable value Remedy
A 540 - Replace
B 500 488 Replace
C 83 75 Replace
D 170 - Replace
E 43.5 50 Replace
F 0.33 ~ 0.44 1.5 Replace
G 0.09 ~ 0.15 - Replace
- After disassembly and assembly, fill SAE10W-30 engine oil 365cc.
-
8/15/2019 ec210b-17.pdf
13/13
Volvo Construction EquipmentKorea Ltd.
EC210B-17-12
Recoil Spring
A90o
40cm
unit:mm(in)Condition Distance (A)
Normal soil 320 ~ 340 (12.6 ~ 13.4)
Rocky ground 300 ~ 320 (11.8 ~ 12.6)
Soft ground (swamp, clay, sandysoil)
340 ~ 360 (13.4 ~ 14.2)