Earthbag Building_ Step by Step Construction

7/30/2019 Earthbag Building_ Step by Step Construction

1/13

Step by Step Earthbag Constructionby Dr. Owen Geiger

To illustrate just how easy earthbag building canbe, this article shows each main step ofconstruction for

building vertical earthbag walls. Follow these steps and you and half-dozen friends can build the walls ofa

625 square foot (58m 2 ) house in about 5-10 days. Videos on my YouTube channel demonstrate theprocess.

The following instructions assume you have cleared and leveled the site, removed topsoil, positioned fill

soil around the building site to minimize work, dug a trench to stable subsoil, put about 12" ofgravel in the

trench, and added corner guides and stringlines.

1. Tools and materials (listed left to right): wovenpolypropylene bags (about 18" x 30" ), bucket chute (4-

gallon bucket withbottom cut off), 4 or 5 heavy duty 2-gallon cement buckets, stringline, metal chisel and

scrap steel for cutting barbed wire (or bolt cutters), hammer, sheetmetal slider (about 13" x 16"), 15 gauge

galvanized wire, knife, wire cutters, tape measure, 4-point barbed wire, corner guide, grub hoe or grape

hoe, level, tampers, bundle 500 bags, shovel.


2/13

2. Fill the bags: use 2-gallon cement buckets to measure the fill material. Use the same number ofbuckets

for each bag. Fill bags approximately 90% full, leaving just enough to sew the bags closed. This technique

ensures a.) each bag is filled to capacity to save bags, and b.) each bag is the same size, which helps keepwalls level. Bag stands are not needed.


3/13

3. Sew or stitch the bags closed: fold the bag end over; use 15 gauge wire about 9" long with one end cut


4/13

at a sharp angle; make one stitch on one side and bend the end over; make a stitch in the center and pull

the corner over; make a stitch in the other corner and pull the corner over; poke the remaining wire into

the earthbag. This technique facilitates handling, prevents spills and enables bags to be filled to capacity.


5/13

4. Lower courses: place gravel-filled bags (double bagged) working from the corners and openings to the

center. It helps to tilt the first two bags against each other. Alignbags to stringline; tamp the bags solid and

level after the course is complete, working from the center ofthe bags outward. Always put tops ofbags(the ends you've sewn closed) butted against other bags (never facing outward on corners or ends).

Maintain a running bond as in masonry.


6/13

5. Add barbed wire: use two strands of4-point barbed wire in-between each course ofbags; bricks or


7/13

stones temporarily hold the barbed wire inplace.


8/13

6. Use a sheetmetal slider to place additional courses so bags do not snag on the barbed wire: fill the bags

on the slider; sew the end closed; tilt the bag into position and push it against the previous bag; after the

bag is aligned, hold the end ofthe bag (it helps to lift it slightly) andjerk the slider out. Continue with

gravel-filled bags until you are safely above grade to avoid risk ofmoisture damage.


9/13

7. Repeat the process using earth-filled bags, but with a few minor changes: turn bags inside out to avoid

protruding corners; use lightly moistened soil; tamp the contents slightly after each bucket load is added;

pre-tamp each bag after it is aligned in position. This last step lengthens each bag to ensure good overlap.


10/13

8. Make custom-sized bags to fill odd-sized spaces: measure the opening; fill the bag to the approximate

level; cut offexcess bag material; fold each side ofthe end toward the center and tuck under the bag;

place the bag in the wall.


11/13

9. Tamping: Tamp earthbags solid and level after each course is complete. Tamp the high points first. Then


12/13

evenly tamp the entire wall several times as you continually move the tamper. This last step avoids creating

low spots.

Notes for 'speed builders':

Here's a recap ofimportant points, along with a few other comments to maximize production.

- First ofall, get 'clean' (mostly free ofrocks, roots, and large clay chunks) sandy-clay soil delivered to the

site and dumped in piles around the building.

- To minimize handling, fill the bags in place on the wall.

- Gravel could be shoveled from the truck directly into the rubble trench foundation.

- Work in teams -- say, two teams for a small house -- and try a little friendly competition.

- Bag size is important. Even a slightly larger bag than 18" x 30" uses more materials and requires extra

work. Bags much less than 18" wide will be unstable for 8' high vertical walls.

- Refine your technique for making custom-sized bags - they tend to be a real time killer. One idea is to

hold a partially filled bag next to where it will go and eyeball how much soil to use. Add more than you

think because it will compress quite a bit.

- Let go ofperfectionism. There's a middle ground between high-precision work, such as masonry, and

careless work. Use reasonable care and no one will notice minor imperfections after the plaster goes on.

And ifyou want, it's relatively easy to tweak and flatten the wall with a tamper before plastering ifthe wall

hasn't dried. (But don't be careless. We've seen some very poorly built walls.)


13/13

- There's no need to tamp the bags excessively, just tamp until they're solid. One minute per bag should be

plenty, maybe go two minutes ifyou're slow and tired. There's a change in tone when they become solidly

compacted.

Owen Geiger, Ph.D. is a TLSCorrespondent, Mother Earth News Green Home Adviser and the

Director ofthe Geiger Research Institute ofSustainable Building. www.grisb.org

Photos and videos by Got Chankamol

Visit ourEarthbagBuilding Blogwhere we provide all the latest earthbag news and answer reader's

questions.

Earthbag Building_ Step by Step Construction

Documents

Transcript of Earthbag Building_ Step by Step Construction