DuraTape RGB RGBW Indoor - DuralampHigh output indoor RGB and RGB+W LED Tapelight strip emits sharp,...
Transcript of DuraTape RGB RGBW Indoor - DuralampHigh output indoor RGB and RGB+W LED Tapelight strip emits sharp,...
DURATAPETM HOINDOOR RGB+W
MODEL(S)
PROJECT TYPE
Spacing 0.66” OC LED Spacing
LEDs 18 LEDs per foot
End Preps Factory preped end preps available (See Page 2)
Field Cuts See page 2 for cut zones
Mounting Includes installation-ready 3M tape adhesive for simplified installation directly to mounting channel or application surface
Installation Optional aluminum channels with base and cover can be used to install decorative, protective covers
Power Supply Listed Class II 24 VDC power supply required
Listing cULus / CE listed
Compliance ROHS compliant
Warranty 3 year warranty
Duratape™
Ordering GuideLED COLORWATTAGE
44 = 4.4 W/ft RGB = Red: 625nm Green: 520nm Blue: 450nm
RGBW = Red: 625nm Green: 520nm Blue: 450nm 3000°K White
IP RATING
I = Indoor IP20
D=Damp IP65 Sleeve
SEE PAGE 5 FOR POWER SUPPLIES& DMX CONTROLS
MODEL INTENSITY
HO = High Output
High Output RGB+W TapelightHigh output indoor RGB and RGB+W LED Tapelight
strip emits sharp, color changing effects in indoorniche, cove and architectural decorative applications.
5/16” O.C.
8“
9/16”
3/16”
Duralamp - Durastrip RGB Indoor
LED DataWattage Viewing Angle Lifespan at 90% drive
0.24W per LED 120° 40,000hrs
* LEDs operating at 90% of LED manufacturers maximum current rating.
Fixture DataModel Efficacy Lm/Wt Lm/Ft Wt/Ft Wt/LED
RGB 37.27 164 4.4 0.24
RGB+W 46.60 205 4.4 0.24
VOLTAGE
24 = 24 VDC
Key Features• Flexible flat conductor strip with High Output Red 625nm,
Green: 520nm, Blue: 465nm + 3000°K White LEDs, RGB colors can be used together with White LED to create different tone of White or soften the RGB color pallet
• Ideal for IP20 interior or IP65 (with optional sleeve) location applications such as cove, under-counter/cabinet, and lighting accents
• Sold per foot and manufactured to specified lengths with factory attached end preps
• All Duratape features 2-circuit substrate for optimum heat dissipation, minimizing voltage drop while increasing run lengths per power feed, standardizing electrical flow over entire length of the strip for maximum product reliability
• All Duratape features double sided solder points for maximum conductivity and durability
• Pre-assembled to specific lengths with various connector options for project requirements and efficient power configuration
• Max continuous length: up to 16’ per run• DMX 512 interface available (see pg. 6)
Dimensional Drawings
0.56"
0.66" O.C.
DL HO 44 24
Details
RGB
RGB+W
IP20 Indoor
5/16”O.C.
13/32”
Duralamp - Duratape Static Indoor
Duralamp - Duratape Static Indoor. With option PVC sleeve
0.09"
IP65 Damp
5/16”O.C.
13/32”
Duralamp - Duratape Static Indoor
Duralamp - Duratape Static Indoor. With option PVC sleeve
5/16”O.C.
13/32”
Duralamp - Duratape Static Indoor
Duralamp - Duratape Static Indoor. With option PVC sleeve
0.17"
5/16”O.C.
13/32”
Duralamp - Duratape Static Indoor
Duralamp - Duratape Static Indoor. With option PVC sleeve
5/16” O.C.
8“
9/16”
3/16”
Duralamp - Durastrip RGB Indoor
0.48"
07.07.15 - Page 1 of 6Copyright © 2015 Duralamp USA – A Targetti Group Company - 3184-C Airway Ave. Costa Mesa, CA 92626 - Phone (714) 513-1991 - Email: [email protected] - www.duralampusa.com
High output indoor RGB and RGB+W LED Tapelightstrip emits sharp, color changing effects in indoor
niche, cove and architectural decorative applications.
RGBRGB
RGB+WRGB+W
DURATAPETM HO INDOOR RGB+W
Field Cut DetailsDuratape can be field cut to accomodate most installations, by cutting at the indicated field cut sections.
Caution! Field cutting should only be done before connection power.
ASingle lead wire prep. 24” Lead wire/dead end allows for connection to power at lead end and field trim of Duratape product at the other end.
BDouble ended lead wire prep. 24” lead wire at both ends.One end can be used for power connectivity while the other end can be used for a jumper cable to run to an additional length of Duratape. Caution: Pay attention to max run lengths and voltage drops from total lead/jumper wire lengths.
CJumper cable (specified length)Jumper cables can be factory attached to Duratape to meet your specified installation requirements. Jumper lengths available as 1”, 2”, 3”, 4”, 6”, 12”. Add length number to end of part number. Caution: Pay attention to max run lengths and voltage drops from total lead/jumper wire lengths.
D12” Additional lead wire Purchased per foot and factory attached to specified run leads. Lead wire can be field cut to desired length.
07UI3CBL1 (3-circuit RGB)07UI4CBL1 (4-circuit RGBW)
07UI3CBL2 (3-circuit RGB)07UI4CBL2 (4-circuit RGBW)
07UI3JMPCBL-XX (3-circuit RGB)07UI4JMPCBL-XX (4-circuit RGBW)
07UI3ADDCBL (3-circuit RGB)07UI4ADDCBL (4-circuit RGBW)
EAdditional connectors. Lead wire connectors 2/ea per connection.
07UI3ADDCON (3-circuit RGB)07UI4ADDCON (4-circuit RGBW)
F
H G
F F
FRemovable/lockable interconnect lead wire. 24” lead wire with locking and unlocking lead connector.
07UI3LICON (3-circuit RGB)07UI4LICON (4-circuit RGBW)
Wiring Options
A B C
H G
F F
D E
H G
F F
H G
F F
H G
F F
H G
F F
5/16” O.C.
8“
9/16”
3/16”
Duralamp - Durastrip RGB Indoor
4” (RGB)
8” (RGB+W)
5/16”O.C.
13/32”
Duralamp - Duratape Static Indoor
Duralamp - Duratape Static Indoor. With option PVC sleeve
Duratape features solder points for maximum continuity for long lifespan.
0.09"
IP20 Indoor IP65 Damp
5/16”O.C.
13/32”
Duralamp - Duratape Static Indoor
Duralamp - Duratape Static Indoor. With option PVC sleeve
5/16”O.C.
13/32”
Duralamp - Duratape Static Indoor
Duralamp - Duratape Static Indoor. With option PVC sleeve
0.17"
5/16”O.C.
13/32”
Duralamp - Duratape Static Indoor
Duralamp - Duratape Static Indoor. With option PVC sleeve
07.07.15 - Page 2 of 6Copyright © 2015 Duralamp USA – A Targetti Group Company - 3184-C Airway Ave. Costa Mesa, CA 92626 - Phone (714) 513-1991 - Email: [email protected] - www.duralampusa.com
DURATAPETM HOINDOOR RGB+W
Mounting Accessories
DL-3-LIC (3-circuit RGB)DL-4-LIC (4-circuit RGBWW)Duratape lockable interconnect. Can be unlocked for easy replacement or maintenance.
DL-3-LIC-90 (3-circuit RGB)DL-4-LIC-90 (4-circuit RGB)Duratape 90º lockable interconnect. Can be unlocked for easy replacement or maintenance.
DL-ALUM-U-4Low profile aluminum U-Channel for linear run lengths, available in 4’ lengths.1/2” ID, 5/8” OD, 1/4” H
DL-ALUM-L-4Low profile aluminum 1/2” x 1/2” L-Channel for linear run lengths. Duratape can be mounted at either 0º or 90º mounting positions. Available in 4’ lengths.
0.69”
0.63”
17mm
19.2mm
22mm24.8mm
0.66”
0.20”
0.66”
0.62”
0.375”
0.20”
0.20”
0.66”
17mm
19.2mm
22mm24.8mm
0.66”
0.20”
0.66”
0.62”
0.375”
0.20”
17mm
19.2mm
22mm24.8mm
0.66”
0.20”
0.66”
0.62”
0.375”
0.20”
0.20”
0.375”
0.66”
0.62”
DL-HT-TAPE1/2” wide thermally conductive mounting tape. Factory attached and sold per foot.
DL-HS-TAPE2” wide aluminum foil tape, used to create a flexible thermal sink. Sold in 100’ rolls.
DL-I-MCHAN-8Mounting channel, sold in 8 foot lengths. Can be used with Duratape (no PVC sleeve) and outdoor Duratape (with PVC sleeve) for linear applications.
DL-I-45-MCH-445° mounting base, sold in 4 foot lengths. Used with Duratape (no PVC sleeve) for 45° mounted linear applications.
DL-I-45-CVR-4-C (Clear)DL-I-45-CVR-4-F/10/F30/F60 (Frosted)45° mounting base cover, sold in 4 foot lengths.
DL-I-2PC-C (Clear)DL-I-2PC-F10/F30/F60 (Frosted)Two-piece mounting tube; base (clear) with cover, sold in 8 foot lengths. Used with Duratape (no PVC sleeve) for linear applications. Clear or frosted at 3 diffusion levels, 10%, 30% or 60%.
DL-3/4-FOLD-I-1Wire fold 1” 18ga wire factory attached between specified lengths of segments (4” intervals). For curved applications that require lateral bends for upward illumination.
DL-3/4-FOLD-I-XSpecified lengths of 18ga wire fold.
DL-3/4-LIC-FOLD-1Duratape lockable interconnect with flexible 1” 18ga wire fold.
DL-3/4-LIC-FOLD-XDuratape lockable interconnect with flexible (specified lengths) 18ga wire fold.
DL-HOEC-20 Silicone end cap for termination of indoor IP20 tape.
DL-HOEC-65Silicone end cap for termination of outdoor IP65 tape.
DL-SLEEVE-CLP-65Sleeve mounting clips. Package of 10 each for 5 ft section.
07.07.15 - Page 3 of 6Copyright © 2015 Duralamp USA – A Targetti Group Company - 3184-C Airway Ave. Costa Mesa, CA 92626 - Phone (714) 513-1991 - Email: [email protected] - www.duralampusa.com
DURATAPETM HO INDOOR RGB+W
17mm
19.2mm
22mm24.8mm
0.66”
0.20”
0.66”
0.62”
0.375”
0.20”
17mm
19.2mm
22mm24.8mm
0.66”
0.20”
0.66”
0.62”
0.375”
0.20”
17mm
19.2mm
22mm24.8mm
0.66”
0.20”
0.66”
0.62”
0.375”
0.20”
PRDE Aluminum channel with dual lens for dual tape runs illuminating in opposite directions.
PRDSAP Aluminum channel with curved lens for dual tape runs for unique lighting effects.
PRDSAN Aluminum channel with curved lens for 45º angled dual tape run illumination.
0.63”
0.75”0.50”0.47”
0.63” 0.63”
2.00” 2.00”
2.00”2.00”
3.75”
1.38”
PRAN20 45º aluminum channel. Anodized aluminum rigid profile complete with white diffuser plastic cover for flush mounting. Suitable for IP65 and IP66 installation applications. Available in 4’ lengths.
DL-AL-CHAN-20-LENS Frosted lens, available in 4’ lengths.
DL-AL-CHAN-20-45EC-1 45º end cap with hole for interconnectivity.
DL-AL-CHAN-20-45EC-2 45º end cap with no hole for run length termination.
DL-AL-CH-45-C-I Mounting clip for indoor aluminum channel.
PRIN20 Flush mount aluminum channel. Anodized aluminum rigid profile complete with white diffuser plastic cover for flush mounting. Suitable for IP65 and IP66 installation applications. Available in 4’ lengths.
DL-AL-CHAN-20-LENS Frosted lens, available in 4’ lengths.
DL-AL-CHAN-20-EC-1 End cap with hole for interconnectivity.
DL-AL-CHAN-20-EC-2 End cap with no hole for run length termination.
DL-AL-CH-WOC-I Mounting clip for indoor aluminum channel.
PRAP20 Surface mount aluminum channel. Anodized aluminum rigid profile complete with white diffuser plastic cover. Suitable for IP65 and IP66 installation applications. Available in 4’ lengths.
DL-AL-CHAN-20-LENS Frosted lens, available in 4’ lengths.
DL-AL-CHAN-20-EC-1 End cap with hole for interconnectivity.
DL-AL-CHAN-20-EC-2 End cap with no hole for run length termination.
DL-AL-CH-WOC-I Mounting clip for indoor aluminum channel.
PRINTC Recessed aluminum channel for walk-over inground applications, includes frosted polycarbonate cover. Suitable for IP65 and IP66 installation applications. Available in 4’ lengths.
DL-AL-CHAN-WOEC-1 End cap with hole for interconnectivity.
DL-AL-CHAN-WOEC-2 End cap with no hole for run length termination.
DL-AL-CH-WOC Mounting clip for indoor aluminum channel.
0.50”
0.50”
Profiles
0.76”
1.00”
50,5
5 m
m 12,4 mm
12,5 mm
47,4 mm
50 mm
49,7
mm
50 mm
12,42 mm
85 mm
47,4 mm
35 m
m
33 m
m
we changed the color fo the back slide because this is aluminum as the rest of the channel, while we colored bluish the polycarb screens, psl note
19,4
mm
16 mm
25 mm
8 m
m
07.07.15 - Page 4 of 6Copyright © 2015 Duralamp USA – A Targetti Group Company - 3184-C Airway Ave. Costa Mesa, CA 92626 - Phone (714) 513-1991 - Email: [email protected] - www.duralampusa.com
DURATAPETM HOINDOOR RGB+W
Power Supplies
Electronic Driver Magnetic Transformer
DuraLamp S.p.A.- A brand of Targetti Poulsen Industries •P.IVA • E-mail:[email protected]
Ver. 1.1 06-2014foegaP
LineVoltage
Input
Duratape
UL listedJ-box
by others
Wiring fromtransformer to
J-box must be toClass II standard.
Refer to NECand local coderequirements.
PowerSupply
LineVoltage
Input
Duratape
UL listedJ-box
by others
Wiring fromtransformer to
J-box must be toClass II standard.
Refer to NECand local coderequirements.
PowerSupply
LineVoltage
Input
Duratape
UL listedJ-box
by others
Wiring fromtransformer to
J-box must be toClass II standard.
Refer to NECand local coderequirements.
PowerSupply
Electronic Driverin Enclosure
LineVoltage
Input
Duratape
UL listedJ-box
by others
Wiring fromtransformer to
J-box must be toClass II standard.
Refer to NECand local coderequirements.
PowerSupply
Cat No Type Voltage Wattage Listing Dimensions
DEL-I-120-1-4-24-D Electronic 90-305V AC / 24V DC 96W / 1X4A** cULus 10”W X 10”L 4”D*
DEL-I-240-2-4-24-D 90-305V AC / 24V DC 192W / 2X4A** cULus 10”W X 10”L 4”D*
DEL-I-320-3-4-24-D 90-305V AC / 24V DC 288W / 3x4A** cULus 10”W X 10”L 4”D*
DEL-120-1-4-24-D 90-305V AC / 24V DC 96W / 1X4A** UL/CE 2.67”W X 9.66”L 1.53”D
DMG-40-1-1.6-24-D Magnetic 120V AC / 24V DC 40W / 1X1.6A** cETLus 2.00”W X 5.06”L 2.14”D
DMG-60-1-2.4-24-D 120V AC / 24V DC 60W / 1X2.4A** cETLus 2.25”W X 6.55”L 2.55”D
DMG-120-1-4-24-D 120V AC / 24V DC 96W / 1X4A** cETLus 3.00”W X 9.80”L 3.00”D
DMG-192-2-4-24-D 120V AC / 24V DC 192W / 2X4A** cETLus 3.00”W X 9.80”L 3.00”D
* Dimensions include enclosure with mounting bracket** 4A maximum current protection for each seconday circuit*** Constant voltage drivers 50HZ , voltage regulated with short circuit protection. operating temperature -40 C- 80° C
Electronic Driver Magnetic Transformer
07.07.15 - Page 5 of 6Copyright © 2015 Duralamp USA – A Targetti Group Company - 3184-C Airway Ave. Costa Mesa, CA 92626 - Phone (714) 513-1991 - Email: [email protected] - www.duralampusa.com
DURATAPETM HO INDOOR RGB+W
System Layout Example Diagram
RGB ControllersCat No Application Voltage Type Listing Dimensions
ZKC-DMX Indoor 12-24V DC RGB DMX Controller cULus 2.25”W X 6.25”L X 1.75”D
ZKTPC-RGBW Indoor 5V DC RGB+W DMX Controller cULus 4.20”W X 5.75”H X 0.40”D
ZKC-DMXW Indoor 24V DC RGW+W DMX Interface cULus 6.60”L X 2.00”W X 0.87”D
ZKC-DMXDimming Module
V+ V- N L
Controller 1
Controller 2
Controller 1
ZKTPC-RGBWRGB+W DMX
Controller
Positive
Negative
Hot
NeutralGround
Standard Dimmable Power Supplies
DEL-I-120-1-4-24DEL-I-240-2-4-24DEL-I-320-3-4-24
ZXC-DMXW
07.07.15 - Page 6 of 6Copyright © 2015 Duralamp USA – A Targetti Group Company - 3184-C Airway Ave. Costa Mesa, CA 92626 - Phone (714) 513-1991 - Email: [email protected] - www.duralampusa.com