DUAL BANDPASS EXTERNAL ANTENNA DUPLEXER...The Mimomax Dual Bandpass MiMO Antenna Duplexer is a high...
Transcript of DUAL BANDPASS EXTERNAL ANTENNA DUPLEXER...The Mimomax Dual Bandpass MiMO Antenna Duplexer is a high...
The Mimomax Dual Bandpass MiMO Antenna Duplexer is a high performance, tuneable cavity RF Filter. With low insertion loss and a very compact footprint, the Dual channel format provides an economical site filter solution for congested sites where space is at a premium. Using only 2U of rack height the Mimomax Dual Antenna filter provides a high quality stable filtering solution for two radio channels (MiMO) in one standalone compact mechanical packaging solution. Mimomax supplies the Dual Bandpass Filter pre-tuned and complete with a 19in 2U Front Panel ready for installation. Note: The Mimomax Dual Bandpass Filter is also suitable for other radio equipment and can be used as an economical solution for multi-channel conventional trunked analogue or digital radio systems.
DUAL BANDPASS EXTERNAL ANTENNA DUPLEXERSpec Sheet
Electrical SpecificationsFrequency Band 440-470MHz product variant
Example 1 Example 2
Low 1 HIgh 1 Low 2 High 2
Frequency Range 439.5-440.5MHZ 449.5-450.5MHZ 439.5-440.5MHZ 444.5-445.5MHZBandwidth 1 MHz (Typically)Insertion Loss Typically < 1dB, worst case over temperature < 1.75dBReturn Loss ≥20dB (typically); ≥15dB (-30°~70°)Rejection ≥85dB @ 450MHz
≥70dB @ 445MHz≥85dB @ 440MHz≥70dB @ 445MHz
≥85dB @ 450MHz≥70dB @ 445MHz
≥85dB @ 435MHz≥70dB @ 440MHz
Power 100W (Continuous)Impedance 50ΩSurface Finish Silver PlatedOperating Temperature -30° to 70°Port Connectors N-FemaleWeight About 5.8kgConfiguration As Below (±0.2mm)
Frequency Band 440-470MHz product variantExample 1 Example 2
Low 1 HIgh 1 Low 2 High 2Frequency Range 459.5-460.5MHZ 469.5-470.5MHZ 464.5-465.5MHZ 469.5-470.5MHZ
Insertion Loss Typically < 1dB, worst case over temperature < 1.75dBReturn Loss ≥20dB (typically); ≥15dB (-30°~70°)Rejection ≥85dB @ 470MHz
≥70dB @ 465MHz≥85dB @ 460MHz≥70dB @ 465MHz
≥85dB @ 475MHz≥70dB @ 470MHz
≥85dB @ 460MHz≥70dB @ 465MHz
Power 100W (Continuous)Impedance 50ΩSurface Finish Silver PlatedOperating Temperature -30° to 70°Port Connectors N-FemaleWeight About 5.8kgConfiguration As Below (±0.2mm)
DUAL BANDPASS EXTERNAL ANTENNA DUPLEXER SPECIFICATIONS
www.mimomax.com
Important: Specifications are subject to change without prior notice
Product Orders
Product Code Frequency Band DescriptionACC-BPD-415-DB-XX00 400-430MHz Dual MiMO Bandpass Duplexer (2x TX 2x RX)ACC-BPD-450-DB-XX00 440-470MHz Dual MiMO Bandpass Duplexer (2x TX 2x RX)
ACC-BPD-490-DB-XX00 470-500MHz Dual MiMO Bandpass Duplexer (2x TX 2x RX)ACC-BPD-510-DB-XX00 500-520MHz Dual MiMO Bandpass Duplexer (2x TX 2x RX)ACC-BPD-420-DB-XX00 410-425MHz 5MHz Passband, 410-415Mhz, 420-425MHzACC-BPD-450-SG-XX00 450-470MHz Single Bandpass Duplexer, can fit 2 in a 2U Rack
www.mimomax.com
v1_2019
www.mimomax.com www.mimomax.com
v1_2019
www.mimomax.com
v1_2019
The Mimomax bandpass filters are designed specifically with the Mimomax radios in mind but may also be used in conjunction with any suitable wireless transmitter or receiver. The band pass filter design is a low insertion loss, wide-band filter solution to fit in both antenna leads of a Mimomax radio. With 6MHz & 11MHz wide design pass-bandwidths, both the Mimomax transmit and receive frequencies can freely pass through the filters, while out of band signals are strongly attenuated.
The Mimomax band pass filter should be considered for use in sites where there are a large number of transmitters or a few high power transmitters in adjacent or nearby bands that are likely to cause blocking problems.
The wide tuning range, steep filter cut rate together with the high power rating ensure these filters are compatible with a wide range of radio equipment and applications. In conjunction with optional band-stop filters, the Mimomax band-pass filter provides an economical low loss solution to site engineering problems encountered on busy sites.
BANDPASS FILTERSpec Sheet
Electrical SpecificationsPass-Band Width 6MHZ (+/- 3MHz) 11MHZ (+/- 5.5MHz)
Pass-Band Loss Typ. < 1dB, Max. < 1.5dB Typ. < 0.7dB, Max, < 1dB
Configuration 6 Element Comb-Line Band Pass Filter
Center Frequency Tuning Range 375-475MHzStop-Band Attention > 70dB at +/- 15MHzPort Impedance 50 OhmsPass-Band Return Loss Typ. > 15dBPower Rating 100 WattsAmbient Temperature Rating -30 to +70 CelsiusConnectors N Type FemaleTuning Adjustments 6 Frequency Adjustment Screws Plus 2 Coupling Adjustment ScrewsDimensions (L x B x H) 420 x 130 x 55 mmWeight (Filter Only) 1.5 kgsMounting Options No Mounting Panel
1 Filter Mounted on 2U Panel2 Filters Mounted on 3U Panel
BANDPASS FILTER SPECIFICATIONS
www.mimomax.com
Important: Specifications are subject to change without prior notice
No Mounting Panel ACC-BPF-425-06-XX00 ACC-BPF-425-11-XX00
1 Filter Mounted on 2U Panel ACC-BPF-425-06-XX01 ACC-BPF-425-11-XX01
2 Filters Mounted on 3U Panel ACC-BPF-425-06-XX02 ACC-BPF-425-11-XX02
v1_2019
Frequecny Response of Filter Tuned to its Bottom, Middle & Top of its Tuning Range
The Mimomax UHF Antenna Combiner is a compact, wideband and rugged T-style antenna combiner. It enables high-gain and cost-effective antenna solutions to be built without the use of expensive and bulky frequency selective phasing harness.
These combiners are designed specifically with Mimomax antennas in mind, however can also be used to combine antennas from any other manufacturers. The Mimomax UHF Antenna Combiner covers the 350-520MHz frequency range and combines two 50 ohms antenna feeds. With a continuous power rating of 100 W (average), a return loss of greater than 20 dB (420-500MHz) and forward loss of less than 0.05dB, the antenna combiner has a good impedance match over the whole band ensuring optimum transmitter and receiver performance. With amplitude balance better than 0.1 dB and phase balance less than 1°, the Mimomax antenna combiner provides a high-performance antenna combining solution.
The Mimomax antenna combiner allows multiple antennas to work with medium diameter cables with Type N connectors. The antenna combiner is suitable for outdoor conditions and waterproof rated IP65.
UHF ANTENNA COMBINERSpec Sheet
Material SpecificationsFrequency Range 350-520MHz
2 x Antenna Ports Type N Female 50 ohm connectors
1 x Common Port Type N Female 50 ohm connector
Power Rating 100 W (average)Impedance Match > 20 dB Return Loss (400-500MHz)
> 15 dB Return Loss (390-520MHz)Forward Loss < 0.05 dBAmplitude Balance < 0.1 dBPhase Balance < 1°Temperature -30°C to +70°C (-22°F to +158°F)Water Tolerance IP65*Dimensions: W x H x T 157 x 60 x 25 mm (6.2 x 2.4 x 1.0 in)Weight 300g (0.7 lbs)*Mimomax recommends that all interface cables and connectors are sealed with appropriate waterproof sealant.
UHF ANTENNA COMBINER SPECIFICATIONS
www.mimomax.com
Important: Specifications are subject to change without prior notice
Product Orders
Product Code Description
ACC-ACO-350-520-00 MiMOMax UHF Antenna Combiner
v1_2019
The Mimomax Four Wire Audio Interface is an external full duplex audio solution that communicates directly with a Mimomax radio unit. It is highly flexible and intended for connectivity to analogue audio equipment, such as VF modems or radio systems with analogue interface. Multiple channels configuration options are avail-able, with optional E & M signalling, and an asynchronous serial interface that eables data communications, such as inter-site signalling or SCADA.
FOUR WIRE AUDIO INTERFACESpec Sheet
Key Features• Toll Quality Audio via a 32 kbp/s ADPCM Vocoder• Tone Transparent to Selcall and CTCSS Tones• Flexible Modes of Operation• Very High Throughput - Up to 6 x 4 Wire Audio E & M plus 9600 Serial• Very Low Latency - Audio <12ms & Serial <7ms end-to-end in a 16QAM 25kHz channel bandwidth• Multiple Configuration Options - Audio - Dynamic (E & M signalling), Static (Non E & M) - Serial - 9600 bps EIA232 Compliant UART• Wide Audio Frequency Range• Multipurpose Solution for: - Fixed Long Haul Analogue Linking - Signalling for VF Modems - Inter-site Signalling - SCADA
Benefits• High Quality• Highly Reliable• Very Robust• Scalable• Near Instantaneous• Environmentally Sound• Very Versatile• Economical• Secure
AudioConnector RJ45
Number of Channels Up to 6
Input Range to Unit -20 dBm to +9dBm (320-35000 Hz)-20 dBm to -10dBm (65-320 Hz)
Insertion Loss +0.6 dB (+/- 0.3 dB) @ 1000 Hz
Nominal Impedance 600 ohm
Delay (1) <6ms (12ms @ 25kHz, 16QAM)
Vocoder 32 kbps ADPCM
Audio Bandwidth 60-3.5kHz
E&M SignalingConnector RJ45 (co-located with audio)
Type Current sense input / switch output
Delay (1) <6ms (2) (12ms@ 25kHz, 16QAM)
UART (EIA232) DataConnector RJ45
Data Rate 9600 (3)
Delay (1) <1ms (4) (7ms @ 25kHz, 16QAM)
Network PortConnector RJ45
PowerConnector Detachable screw terminal
Type Isolated DC/DC converter
Isolation 1500 volts
Nominal Input Voltage 12 to 48 V DC
Power Consumption < 1.5W
Mechanical Dimension 38mm x 140mm x 258mm (H x W x D)
EnvironmentalTemperature (Operational)
- 25 ºC to 60 ºC
Relative Humidity (Operational)
4% to 100% (per EN 300 019 sec. 3.3 & 4.2H)
Altitude (Operational)
0 to 3000m
Environmental Protection
IP20 (Indoor use only)
FOUR WIRE AUDIO INTERFACE SPECIFICATIONS
www.mimomax.com
v1_2019
Radio Unit Bandwidth Net Available Radio Unit Bandwidth (bps)
16 QAM 64 QAM 256 QAM
25 kHz 129000 194000 258000
12.5 kHz 65000 97000 129000
Interface Bandwidth Requirements7 Channel Mode (6 x Audio & 1 x UART) (5)
Active Channels (Static or Dynamic)
No UART Plus UART (6)
0 Audio 0 19200 bps
1 Audio 64000 bps 73600 bps
2 Audio 96000 bps 105600 bps
3 Audio 128000 bps 137600 bps
4 Audio 160000 bps 169600 bps
5 Audio 192000 bps 201600 bps
6 Audio 224000 bps 233600 bps
3 Channel Mode (2 x Audio & 1 x UART)
Active Channels (Static or Dynamic)
No UART Plus UART (7)
0 Audio 0 19200 bps
1 Audio 64000 bps 64000 bps
2 Audio 96000 bps 96000 bps
Fixed Channel Mode
Fixed Channels No UART(8)
0 Audio 0
1 Audio 32000 bps
2 Audio 64000 bps
(1) Quoted delays are for back-to-back connected FWA Interfaces following channel initialization. Quoted delays within brackets are including radio unit and are dependant on modulation settings.(2) E & M delay includes a 5ms debounce delay.(3) Additional rates are available by request only.(4) For the UART the quoted delay does not account for the interface transmission delay (eg. The time to transfer a word between the UARTs).(5) Concurrent channel operation is dependent on available radio bandwidth.(6) In 7 Channel Mode the bandwidth required for UART data is equal to the nominal UART data rate. When only UART data is present bandwidth is also required for protocol overheads.(7) In 3 Channel Mode the data bandwidth is carried in a protocol header and therefore the required bandwidth is Independent of the UART data rate. Nominal rates greater than 9600 bps are NOT supported.
(8) UART data is NOT supported.
Four Wire Audio Interface Connected to Mimomax Radio
Mimomax Link-end Radio Unit Mimomax Four Wire Audio Interface Box
These filters are designed to allow Mimomax RRU-T and BRU-T to coexist in very close proximity to adjacent-band cellular services (such as Verizon and FirstNet), without suffering interference.
The filters are intended to be fitted in each of the antenna feedlines of either the RRU-T or BRU-T as required.
Each path through the filter consists of a parallel pair of very sharp filters intended to pass the Mimomax signals while rejecting the cellular signals on either side.
There are two variants of the filter, one optimised for the use at radio with Tx high locations and one optimised for radio with Tx low locations.
Key Features:• Low Insertion Loss• High Integration• High Reliability
700MHZ DUAL CAVITY FILTER - TX HIGHSpec Sheet
www.mimomax.comwww.mimomax.com
v3_2019
Figure 1 Wall mount configuration
Figure 2 Rack mount configuration
Electrical SpecificationsParameter Tx High
Frequency Range 757-758 MHz 787-788 MHz
Return Loss ≥ 15 dB ≥ 15 dB
Insertion Loss (+77°F/+25°C) ≤ 3.0 dB ≤ 1.0 dB
Insertion Loss (-4°F/-20°C to +158°F/+70°C) ≤ 4.5 dB ≤ 1.1 dB
Rejection ≥ 15 dB @ 757.5MHz ± 1.5MHz
≥ 15 dB @ 787.5MHz ± 4MHz
Power Handling 5 Watts (37dBm)
Temperature Range -4°F to +158°F (-20°C to +70°C)
Mechanical SpecificationsDimension (L x W x H) Rack mount: 440 x 150 x 43.6 mm
Wall mount: 263 x 150 x 95 mm
Port Connectors N-Female
Finish White
Mounting Wall mount and 19” Rack mount
Indoor use
700MHZ DUAL CAVITY FILTER - TX HIGH SPECIFICATIONS
www.mimomax.com
Important: Specifications are subject to change without prior notice
Product Orders
Product Code DescriptionACC-BPF-700-DB-01TH 700MHz Dual Cavity Filter - Tx High
www.mimomax.com
v3_2019
700MHZ DUAL CAVITY FILTER - TX HIGH PICTURES
www.mimomax.com
v3_2019
Picture 1 Wall mount configuration
Picture 2 Rack mount configuration
These filters are designed to allow Mimomax RRU-T and BRU-T to coexist in very close proximity to adjacent-band cellular services (such as Verizon and FirstNet), without suffering interference.
The filters are intended to be fitted in each of the antenna feedlines of either the RRU-T or BRU-T as required. Each path through the filter consists of a parallel pair of very sharp filters intended to pass the MiMOMax signals while rejecting the cellular signals on either side.
There are two variants of the filter, one optimised for the use at radio with Tx high locations and one optimised for radio with Tx low locations.
Key Features: • Low Insertion Loss • High Integration • High Reliability
700MHZ DUAL CAVITY FILTER - TX LOWSpec Sheet
www.mimomax.comwww.mimomax.com
v3_2019
Figure 1 Wall mount configuration
Figure 2 Rack mount configuration
Electrical SpecificationsParameter Tx Low
Frequency Range 757-758 MHz 787-788 MHz
Return Loss ≥ 15 dB ≥ 15 dB
Insertion Loss (+77°F/+25°C) ≤ 1.0 dB ≤ 3.0 dB
Insertion Loss (-4°F/-20°C to +158°F/+70°C) ≤ 1.1 dB ≤ 4.5 dB
Rejection ≥ 15 dB @ 757.5MHz ± 4MHz ≥ 15 dB @ 787.5MHz ± 1.5MHz
Power Handling 5 Watts (37dBm)
Temperature Range -4°F to +158°F (-20°C to +70°C)
Mechanical SpecificationsDimension (L x W x H) Rack mount: 440 x 150 x 43.6 mm
Wall mount: 263 x 150 x 95 mm
Port Connectors N-Female
Finish White
Mounting Wall mount and 19” Rack mount
Indoor use
700MHZ DUAL CAVITY FILTER - TX LOW SPECIFICATIONS
www.mimomax.com
Important: Specifications are subject to change without prior notice
Product Orders
Product Code DescriptionACC-BPF-700-DB-01TL 700MHz Dual Cavity Filter - Tx Low
www.mimomax.com
v3_2019
700MHZ DUAL CAVITY FILTER - TX LOW PICTURES
www.mimomax.com
v3_2019
Picture 1 Wall mount configuration
Picture 2 Rack mount configuration
This is a filter designed to split a band of frequencies into two sub-bands. It has 3 ports, a common port for the combined bands and separate port for each of the sub-bands.
It is primarily intended to allow two radio transceivers operating on different bands to share the same antenna.
This removes the need to fit an additional antenna and coaxial cable, saving cost and overcoming the difficulty in fitting two omni-directional antennas on the same pole.
BAND SPLITTING FILTERSpec Sheet
Mechanical SpecificationsDimension (L x W x H) 5.39” x 2.36” x 1.25” (max 1.53”)
(137mm x 60mm x 32mm (max 39mm))Port Connectors N-Female
Finish White painted
Notes RoHS
Electrical SpecificationsParameter LOW Band HIGH BandFrequency Range 757-788 MHz 900-930 MHzReturn Loss ≥ 15 dBInsertion Loss ≤ 0.5 dBIsolation ≥ 70 dB @ 757-788 MHz &
900-930 MHzPower Handling 5 Watts (37dBm)Temperature Range -4°F ~ +158°F (-20°C ~ +70°C)
BAND SPLITTING FILTER SPECIFICATIONS
www.mimomax.com
Important: Specifications are subject to change without prior notice
Product Orders
Product Code Description
ACC-BSF-700-900-00 Band-Splitting Filter
v1_2019
TORNADO AND PYXIS RJ45 TO DB9-F ADAPTER FOR RS232 CONNECTION TO A DTESpec Sheet
Pin OutSignal Name RJ45 Pin dB9 Pin
Signal Ground 4 5
Rx Data 5 2
Tx Data 6 3CTS 7 8RTS 8 7
Material SpecificationsTerminal Material Gold plated brassHousing Material ABSScrew Material Nickel plated steelScrew Thread #4-40 UNCWire Gauge 26AwgFlammability UL94 V-0
Mechanical SpecificationsDimensions 2.1 x 1.3 x 0.6 inches (53 x 33 x 16 mm)
Important: Specifications are subject to change without prior notice
Product Orders
Product Code Description
ACC-RJ45-DB9F-DTE Tornado and Pyxis RJ45 to DB9-F adapter for RS232 connection to a DTE
TORNADO AND PYXIS RJ45 TO DB9-M ADAPTER FOR RS232 CONNECTION TO A DCESpec Sheet
Pin OutSignal Name RJ45 Pin dB9 Pin
5VDC 1 4
Signal Ground 4 5
Rx Data 5 3
Tx Data 6 2CTS 7 7RTS 8 8
Material SpecificationsTerminal Material Gold plated brassHousing Material ABSScrew Material Nickel plated steelScrew Thread #4-40 UNCWire Gauge 26AwgFlammability UL94 V-0
Mechanical SpecificationsDimensions 2.1 x 1.3 x 0.6 inches (53 x 33 x 16 mm)
Important: Specifications are subject to change without prior notice
Product Orders
Product Code Description
ACC-RJ45-DB9M-DCE Tornado and Pyxis RJ45 to DB9-M adapter for RS232 connection to a DCE