DRAWING MUST BE VIEWED IN ADOBE READER TO ENABLE … · drawing must be viewed in adobe reader to...
1
PROJECT: TITLE: DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY NO.: DATE: REVISION: DATE: 5.26.2017 SCALE: NTS DRAWING NUMBER: US.WSBS.08.13 USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS. PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING. US CORPORATE ADDRESS 310 QUADRAL DRIVE WADSWORTH, OHIO 44281 www.soprema.us Tel:330.334.0066 WI LLI AM GRANT GALLOWAY DRAWING MUST BE VIEWED IN ADOBE READER TO ENABLE CUSTOM LAYERING NOTES: 1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SDS) FOR ADDITIONAL INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES. 2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERTA RECOMMENDATIONS, LOCAL CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS. 3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENT. 4. SOPRAJOINT CAN ACCOMMODATE A MAXIMUM GAP OF 2 INCHES AND A MAXIMUM 3/4 INCHES OF MOVEMENT. 2 PLY SBS MEMBRANE, NON-INSULATED, LOW PROFILE EXPANSION JOINT EMBED SURFACING GRANULES AS REQUIRED POLYESTER REINFORCED FLASHING CAP SHEET WITH GRANULE SURFACING EXTEND FLASHING CAP SHEET A MINIMUM OF 6" BEYOND SEPARATOR SHEET, HEAT WELD TO CAP SHEET ONLY SOPRAJOINT VOILE 100, SEPARATOR SHEET LOOSE LAID SOPRAJOINT, HEAT WELDED, REMOVE PAPER RELEASE FILM (NOT SHOWN) AFTER IT HAS COOLED BASE SHEET/ANCHOR SHEET BASE SHEET/ANCHOR SHEET GAP FILLED WITH COMPRESSIBLE INSULATION AS REQUIRED BY SPECIFIER BASE PLY CAP SHEET SOPRAJOINT LM BANDE, MINERAL WOOL LOOSE LAID DECK DECK BARRIER BOARD DECK DECK BARRIER BOARD DECK DECK BARRIER BOARD DECK DECK BARRIER BOARD DECK BARRIER BOARD DECK DECK BARRIER BOARD OVERBURDEN NOT SHOWN FOR CLARITY, REFER TO WATERPROOFING OVERBURDEN DETAILS
Transcript of DRAWING MUST BE VIEWED IN ADOBE READER TO ENABLE … · drawing must be viewed in adobe reader to...
PROJECT:
TITLE:
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: DATE:REVISION:
DATE: 5.26.2017
SCALE: NTS
DRAWING NUMBER:
US.WSBS.08.13USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
US CORPORATE ADDRESS310 QUADRAL DRIVE
WADSWORTH, OHIO 44281www.soprema.usTel:330.334.0066
W I L L I A M G R A N T G A L L O W A Y
DRAWING MUST BE VIEWED IN ADOBE READER TO ENABLE CUSTOM LAYERING
NOTES:1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SDS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THEDETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERTA RECOMMENDATIONS, LOCALCODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENT.4. SOPRAJOINT CAN ACCOMMODATE A MAXIMUM GAP OF 2 INCHES AND A MAXIMUM 3/4 INCHES OF MOVEMENT.
2 PLY SBS MEMBRANE,NON-INSULATED,
LOW PROFILE EXPANSION JOINT
EMBED SURFACINGGRANULES AS REQUIRED
POLYESTER REINFORCED FLASHING CAP SHEETWITH GRANULE SURFACING
EXTEND FLASHING CAP SHEET A MINIMUM OF6" BEYOND SEPARATOR SHEET, HEAT WELD TOCAP SHEET ONLY
SOPRAJOINT VOILE 100, SEPARATOR SHEET LOOSE LAID
SOPRAJOINT, HEAT WELDED,REMOVE PAPER RELEASE FILM (NOT SHOWN) AFTER IT HAS COOLED
BASE SHEET/ANCHOR SHEET
BASE SHEET/ANCHOR SHEET
GAP FILLED WITH COMPRESSIBLEINSULATION AS REQUIRED BY SPECIFIER
BASE PLY
CAP SHEETSOPRAJOINT LM BANDE, MINERAL WOOL LOOSE LAID
DECKDECK
BARRIER BOARD
DECKDECK
BARRIER BOARD
DECKDECK
BARRIER BOARD
DECKDECK
BARRIER BOARD
DECK
BARRIER BOARD
DECKDECK
BARRIER BOARD
OVERBURDEN NOT SHOWNFOR CLARITY, REFER TOWATERPROOFINGOVERBURDEN DETAILS
