DOOR SWING REVERSAL INSTRUCTIONS W10661460B ... - Whirlpool
2
Steps 3 & 4 apply only to certain models While holding the door, remove 3 hex head screws and the hinge pin. DOOR SWING REVERSAL INSTRUCTIONS W10661460B (OPTIONAL) Remove food and any adjustable bins from the doors. IMPORTANT: Unplug refrigerator or disconnect power. Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working. When removing the door, keep the screws and hinges. You will need them to reinstall the door. For more detailed door reversing instructions, see the User Instructions. Lift freezer door from the center hinge pin. 2 Center Hinge - Loosen the 2 screws (6 turns) on the left- hand side and remove the screw from the right-hand side. 3 4 Center Hinge - While holding the door, loosen the 2 screws on the right-hand side and remove the screw from the left-hand side. 5 Remove Freezer and Refrigerator Doors NOTE: After removing the doors, place them on a soft surface to avoid damaging the finish. Move the door stop, located on the bottom of the door, to the opposite side. A. Door Stop Screw B. Door Stop Move the door stop, located on the bottom of the door, to the opposite side. A. Door Stop Screw B. Door Stop Move the 3 cabinet hole plugs to the opposite side. 1 Reverse Door Stops Freezer Door Refrigerator Door Install Doors Freezer Door Refrigerator Door Align Doors 1 Completely tighten the 3 Top Hinge screws. 2 Move the base grille cover to the opposite side. 3 Reinstall the base grille. 4 Tighten the two screws (previously loosened), and reinstall and tighten the Center Hinge screw. Tools Required " Hex head socket wrench " Open-end wrench Phillips screwdriver ¼" Hex key Flat 2" putty knife Reversibility Kit (a) Removal tool (b) Brand badge (c) Instructions (d) Hole plug (e) Two screws 5 16 / 5 16 / (a) (b) (c) (d) (e) WARNING Excessive Weight Hazard Use two or more people to move and install refrigerator. Failure to do so can result in back or other injury. 5 W10661460B © 2014 Whirlpool Corporation. All rights reserved. 6/14 Printed in Mexico Open doors left to right. Open doors right to left. 1 Insert the 3 Top Hinge screws so they are halfway into the Top Hinge and the top of the cabinet. 2 Set the freezer door onto the Center Hinge. 3 A B A B 1 1 Brand Badge Lift refrigerator door from bottom hinge. NOTE: The hinge style will vary depending on the model. 6 or For models with base grilles, firmly pull the grille toward you to remove. Move the bottom hinge to the opposite side of the cabinet. Make sure the washer remains on the hinge pin. NOTE: The hinge style will vary depending on the model. 1 or Set the refrigerator door onto the bottom hinge pin. 2 3 Tighten the screws (previously loosened), and reinstall and tighten the Center Hinge screw. NOTE: Make sure washers are on both the top and bottom pins of the center hinge. 1 8 / Align the Freezer and Refrigerator doors. NOTE: Make sure to allow a ¾" (19 mm) gap between the doors. ¾" (19 mm)
Transcript of DOOR SWING REVERSAL INSTRUCTIONS W10661460B ... - Whirlpool
Ste
ps 3
& 4
app
ly o
nly
to c
erta
in m
odel
s
While holding the door,remove 3 hex head screws
and the hinge pin.
DOOR SWING REVERSAL INSTRUCTIONS W10661460B (OPTIONAL)Remove food and any adjustable bins from the doors.
IMPORTANT: Unplug refrigerator or disconnect power. Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.When removing the door, keep the screws and hinges. You will need them to reinstall the door. For more detailed door reversing instructions, see the User Instructions.
Lift freezer door fromthe center hinge pin.
2
Center Hinge - Loosen the 2screws (6 turns) on the left-hand side and remove the
screw from the right-hand side.
3 4
Center Hinge - While holding thedoor, loosen the 2 screws on theright-hand side and remove thescrew from the left-hand side.
5
Remove Freezerand Refrigerator
DoorsNOTE: After removing thedoors, place them on a softsurface to avoid damagingthe finish.
Move the door stop, located on the bottom of the door,to the opposite side.
A. Door Stop Screw B. Door Stop
Move the door stop, located on the bottom of the door,to the opposite side.
A. Door Stop Screw B. Door Stop
Move the 3 cabinet holeplugs to the opposite side.
1
Rev
erse
Do
or
Sto
ps
FreezerDoor
RefrigeratorDoor
Inst
all D
oo
rs
FreezerDoor
RefrigeratorDoor
AlignDoors
1
Completely tighten the3 Top Hinge screws.
2
Move the base grille coverto the opposite side.
3
Reinstall the base grille.
4
Tighten the two screws (previouslyloosened), and reinstall and
tighten the Center Hinge screw.
Tools Required
" Hex head socket wrench
" Open-end wrench
Phillips screwdriver
¼" Hex key
Flat 2" putty knife
Reversibility Kit
(a) Removal tool
(b) Brand badge
(c) Instructions
(d) Hole plug
(e) Two screws
516/
516/
(a) (b)
(c)(d)
(e)
WARNINGExcessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
5W10661460B© 2014 Whirlpool Corporation.All rights reserved.
6/14Printed in Mexico
Open doors left to right. Open doors right to left.
1
Insert the 3 Top Hinge screwsso they are halfway into the
Top Hinge and the top ofthe cabinet.
2
Set the freezer dooronto the Center Hinge.
3
A
B
A
B
1
1
BrandBadge
Lift refrigerator door from bottomhinge. NOTE: The hinge style will
vary depending on the model.
6or
For models with base grilles,firmly pull the grille
toward you to remove.
Move the bottom hinge to the opposite sideof the cabinet. Make sure the washer remains
on the hinge pin. NOTE: The hinge stylewill vary depending on the model.
1or
Set the refrigerator door ontothe bottom hinge pin.
2 3
Tighten the screws (previously loosened),and reinstall and tighten the Center Hinge screw.NOTE: Make sure washers are on both the top
and bottom pins of the center hinge.
18/
Align the Freezer and Refrigeratordoors. NOTE: Make sure to allow a¾" (19 mm) gap between the doors.
¾"(19 mm)
2 3 4 5
Démontage desportes du
réfrigérateur et ducongélateur
REMARQUE :
1
Inve
rsio
n de
s bu
tées
de
port
eIn
stal
latio
n d
es p
ort
es
Alignementdes portes
1 2 3 4 5
1
2 3
A
B
A
B
1
1
REMARQUE :
REMARQUE :
1 2 3
REMARQUE :
W10661460B (FACULTATIF)IMPORTANT :
AVERTISSEMENTRisque du poids excessif
Utiliser deux ou plus de personnes pour déplacer et installer le réfrigérateur.
Le non-respect de cette instruction peut causer une blessure au dos ou d'autre blessure.
W10661460B©2014
ts é Ut s e a Ca a
/14I p é Me e
Outillage nécessaire
¼
5/
Insigne dela marque
5/
18/
¾
REMARQUE :
