DOOR SWING AND HANDLE REVERSAL …...Steps 3 & 4 apply only to certain models DOOR SWING AND HANDLE...
2
Steps 3 & 4 apply only to certain models DOOR SWING AND HANDLE REVERSAL INSTRUCTIONS W10661461B (OPTIONAL) Remove food and any adjustable bins from the doors. IMPORTANT: Unplug refrigerator or disconnect power. Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working. When removing the door, keep the screws and hinges. You will need them to reinstall the door. For more detailed door reversing instructions, see the User Instructions. Lift freezer door from the center hinge pin. 2 Center Hinge - Loosen the 2 screws (6 turns) on the left- hand side and remove the screw from the right-hand side. 3 4 Remove Freezer and Refrigerator Doors NOTE: After removing the doors, place them on a soft surface to avoid damaging the finish. Move the door stop, located on the bottom of the door, to the opposite side. A. Door Stop Screw B. Door Stop Move the door stop, located on the bottom of the door, to the opposite side. A. Door Stop Screw B. Door Stop Move the 3 cabinet hole plugs to the opposite side. 1 Insert the 3 Top Hinge screws so they are halfway into the Top Hinge and the top of the cabinet. 2 Set the freezer door onto the Center Hinge. 3 Remove the door handle, the screw and the decal or hole plug from the door. 2 Move the decal or hole plug and the handle screw to the opposite sides of the door. Tighten the handle screws. 4 Set the Refrigerator door onto the bottom hinge pin. 2 Reverse Doors Freezer Door Refrigerator Door Install Doors Freezer Door Refrigerator Door Align Doors Align the Freezer and Refrigerator doors. NOTE: Make sure to allow a ¾" (19 mm) gap between the doors. 1 Completely tighten the 4 Top Hinge screws. 2 Move the base grille cover to the opposite side. 3 Reinstall the base grille. 4 Tighten the two screws (previously loosened), and reinstall and tighten the Center Hinge screw. Tools Required " Hex head socket wrench " Open-end wrench Phillips screwdriver ¼" Hex key Flat 2" putty knife Reversibility Kit (a) Removal tool (b) Brand badge (c) Instructions (d) Hole plug (e) Two screws 5 16 / 5 16 / (a) (b) (c) (d) (e) WARNING Excessive Weight Hazard Use two or more people to move and install refrigerator. Failure to do so can result in back or other injury. 5 W10661461B © 2014 Whirlpool Corporation. All rights reserved. 6/14 Printed in Mexico Open doors left to right. Open doors right to left. 1 While holding the door, remove 3 hex head screws and the hinge pin. A B A B 1 1 Remove the handle and brand badge from the door. NOTE: Handles are not factory-installed on some models. 2 Brand Badge Place the badge (using the template provided on the last page of the manual), and the handle on the opposite sides of the door. 3 Tighten the handle screws. 4 Brand Badge 3 3 Tighten the screws (previously loosened), and reinstall and tighten the Center Hinge screw. NOTE: Make sure washers are on both the top and bottom pins of the center hinge. Brand Badge Center Hinge - While holding the door, loosen the 2 screws on the right-hand side and remove the screw from the left-hand side. 5 For models with base grilles, firmly pull the grille toward you to remove. Lift refrigerator door from bottom hinge. NOTE: The hinge style will vary depending on the model. 6 or Move the bottom hinge to the opposite side of the cabinet. Make sure the washer remains on the hinge pin. NOTE: The hinge style will vary depending on the model. 1 or 1 8 / ¾" (19 mm)
Transcript of DOOR SWING AND HANDLE REVERSAL …...Steps 3 & 4 apply only to certain models DOOR SWING AND HANDLE...
Ste
ps 3
& 4
app
ly o
nly
to c
erta
in m
odel
s
DOOR SWING AND HANDLE REVERSAL INSTRUCTIONS W10661461B (OPTIONAL)Remove food and any adjustable bins from the doors. IMPORTANT: Unplug refrigerator or disconnect power. Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.When removing the door, keep the screws and hinges. You will need them to reinstall the door. For more detailed door reversing instructions, see the User Instructions.
Lift freezer door fromthe center hinge pin.
2
Center Hinge - Loosen the 2screws (6 turns) on the left-hand side and remove the
screw from the right-hand side.
3 4
Remove Freezerand Refrigerator
DoorsNOTE: After removing thedoors, place them on a softsurface to avoid damagingthe finish.
Move the door stop, located on the bottom of the door,to the opposite side.
A. Door Stop Screw B. Door Stop
Move the door stop, located on the bottom of the door,to the opposite side.
A. Door Stop Screw B. Door Stop
Move the 3 cabinet holeplugs to the opposite side.
1
Insert the 3 Top Hinge screwsso they are halfway into the
Top Hinge and the top ofthe cabinet.
2
Set the freezer dooronto the Center Hinge.
3
Remove the door handle, the screwand the decal or hole plug from the door.
2
Move the decal or hole plug and the handlescrew to the opposite sides of the door.
Tighten the handlescrews.
4Set the Refrigerator door onto
the bottom hinge pin.
2
Rev
erse
Do
ors
FreezerDoor
RefrigeratorDoor
Inst
all D
oo
rs
FreezerDoor
RefrigeratorDoor
AlignDoors
Align the Freezer and Refrigeratordoors. NOTE: Make sure to allow a¾" (19 mm) gap between the doors.
1
Completely tighten the4 Top Hinge screws.
2
Move the base grille coverto the opposite side.
3
Reinstall the base grille.
4
Tighten the two screws (previouslyloosened), and reinstall and
tighten the Center Hinge screw.
Tools Required
" Hex head socket wrench
" Open-end wrench
Phillips screwdriver
¼" Hex key
Flat 2" putty knife
Reversibility Kit
(a) Removal tool
(b) Brand badge
(c) Instructions
(d) Hole plug
(e) Two screws
516/
516/
(a) (b)
(c)(d)
(e)
WARNINGExcessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
5W10661461B© 2014 Whirlpool Corporation.All rights reserved.
6/14Printed in Mexico
Open doors left to right. Open doors right to left.
1
While holding the door,remove 3 hex head
screws and the hinge pin.
A
B
A
B
1
1
Remove the handle and brandbadge from the door.
NOTE: Handles are not factory-installedon some models.
2
Brand
Badge
Place the badge (using the template providedon the last page of the manual), and thehandle on the opposite sides of the door.
3
Tighten the handlescrews.
4Brand
Badge
3
3
Tighten the screws (previously loosened),and reinstall and tighten the Center Hinge screw.NOTE: Make sure washers are on both the top
and bottom pins of the center hinge.
BrandBadge
Center Hinge - While holding thedoor, loosen the 2 screws on theright-hand side and remove thescrew from the left-hand side.
5
For models with base grilles,firmly pull the grille
toward you to remove.
Lift refrigerator door from bottomhinge. NOTE: The hinge style will
vary depending on the model.
6or
Move the bottom hinge to the opposite sideof the cabinet. Make sure the washer remains
on the hinge pin. NOTE: The hinge stylewill vary depending on the model.
1or
18/
¾"(19 mm)
2 3 4
1 2 3
2 4
2
1 2 3 4
¼
5/
5
1
A
B
A
B
1
1
2 3 4
3
3
Insigne dela marque
5
15/
Insigne de
la marque
Insigne de
la marque
AVERTISSEMENT
W10661461B©2014
ts é Ut s e a Ca a
/14I p é Me e
18/
