DC2 Alarm Enabling - geeksquad.compustar.com...Microsoft Word - DC2 Alarm Enabling Author: nickf...

5
Technical Tip www.Compustar.com | Tech. Support: 888-820-3690 FT-DC2-S/AS Alarm Feature Activation With a new product comes a learning curve. While we attempted to minimize the differences between our standard brains (CM800-S, CM600-AS, CM7x00, etc.), there are some important differences to note. When attempting to use the DC2 as a full remote start with security, whether it’s the DC2S or DC2AS the alarm feature is OFF by default. This will give you a step by step walk through to enable the alarm feature. a. Select the Vehicle the DC2 is Getting Installed Into For demonstration purposes we’ve already selected a vehicle. Once you’ve selected the vehicle it will show you the firmware the control module will be flashed to. Before hitting “ FLASH!” you’ll want to select “CONFIGURE FEATURES.”

Transcript of DC2 Alarm Enabling - geeksquad.compustar.com...Microsoft Word - DC2 Alarm Enabling Author: nickf...


Technical Tip

www.Compustar.com | Tech. Support: 888-820-3690

FT-DC2-S/AS Alarm Feature Activation

With a new product comes a learning curve. While we attempted to minimize the differences between our standard brains (CM800-S, CM600-AS, CM7x00, etc.), there are some important differences to note. When attempting to use the DC2 as a full remote start with security, whether it’s the DC2S or DC2AS the alarm feature is OFF by default. This will give you a

step by step walk through to enable the alarm feature.

a. Select the Vehicle the DC2 is Getting Installed Into

For demonstration purposes we’ve already selected a vehicle. Once you’ve selected the vehicle it will show you the firmware the control module will be flashed to. Before hitting “FLASH!” you’ll want to select “CONFIGURE FEATURES.”


Technical Tip

www.Compustar.com | Tech. Support: 888-820-3690

b. Select Menu #3 – “Security” You’ll be presented with 8 menus in which to control different features of the DC2. Menu #3, labeled “Security” is where

we will need to be to enable the alarm features.


Technical Tip

www.Compustar.com | Tech. Support: 888-820-3690

c. Select the Alarm Feature & Turn it On


Technical Tip

www.Compustar.com | Tech. Support: 888-820-3690

d. Click “SAVE / FLASH”


Technical Tip

www.Compustar.com | Tech. Support: 888-820-3690

e. Installation Notes

The Brown / Black Dot wire on the M2 connector (Black 12 pin connector, pin 7) is your siren output.

The Red 4-pin connector at the end of the DC2 (near LED 2) is for the FT-DAS sensor.

The dial, next to the Red 4-pin FT-DAS port is for the FT-DAS sensitivity with settings OFF to 10. 1 is the LEAST sensitive, 10 is the MOST sensitive - - this is opposite when compared to the FT-7S and FT-7AS controllers.